Search Documents

By N. V. Hansell

l. INTRODUCTION. THE last few years have shown an increasing interest in the subject of beneficiating iron-ores -in all iron-producing countries. In the United States, this movement has been slower than in certain parts of Europe, for the obvious reason that the abundance and relative cheapness of the Lake Superior iron ores has hindered the development of enterprises for the preparation of low-grade ores. Gradually, however, conditions have changed. The world's consumption of iron is increasing enormously. Being in 1900 about 40,000,000 tons, in 1910 ii was already 60,000000; and there is no reason to doubt that for the near future the increase in iron-consumption will continue at the same rapid rate, especially with, the development of China, certain parts of Africa, and other regions which have hardly been touched as yet by modern industrialism. It is. therefore, not surprising that apprehension is felt that the known available iron-ore resources of the world are gradually being depleted. Signs of this feeling are the recent investigation, under the direction of the U. S. Geological Survey, of the iron-ore resources of the United States, and the estimate presented to the last International Geological Congress, at Stockholm, Sweden, of the iron-ore resources of the world. These investigations have emphasized the fact that the known high-grade ore-deposits are limited in extent, and will, at a not distant future, be exhausted, compelling the iron industry to depend for raw material on the enormous deposits of low-grade ores which are distributed over almost all the world. The discovery of new deposits of high-grade ore, in countries not yet thoroughly explored, will not materially change this prospect. Of course, the part which such new deposits will play in the future cannot be forecast. The difficulty and cost of transportation will probably exclude many of them from use at the present centers of the iron industry.

May 1, 1912

By E. A. Breitenbach

A computer program has been developed to afford rapid and complete quantitative log analysis for exploration and production decisions. The computation consists of automatic selection of tops and bottoms of porous intervals from the digitized data, and then point-by-point calculations within each selected interval. Nearly all log types can be analyzed. This paper presents the calculation techniques found to be appticable to machine evaluation and gives examples of their use. INTRODUCTION As the quantitative interpretation of well logs entails repetitive use of charts and equations, it is natural that digital computer programs would be written. A Universal Log Interpretation Computer Program (ULICP) has been developed to afiord rapid and complete analysis for exploration and production decisions. Application of this program enables the log analyst to: (I) apply rapid quantitative log analysis for exploration and production decisions on either a field, a well or on a single zone basis; (2) apply concepts of interpretation requiring detailed numerical analysis; (3) analyze all porous intervals on each log, rather than a few selected zones, and complete the analysis in less time than previously required. Computations are reported for every digitized point in each zone; (4) use empirical techniques applicable to a given area as an integral part of the computation; (5) experiment with the empirical coefficients and exponents in the interpretation equations to find the best possible solution; and (6) automatically plot both the original and computed data to scales analogous to the field prints. The primary utility of a log interpretation program stems from its ability to do an overwhelming amount of work with very little man-power. If a calculation procedure or thought process can be formalized to the extent that step-by-step logic can be written, a computer program can be developed that follows this logic. The major question is one of economics. A feasibility study of the costs for such a program indicates that digital processing is economical primarily as a means of increasing the productivity of the log analyst. In effect, the probability of missing productive intervals in any well, because of a lack of time to do detailed calculations, is greatly reduced. The nucleus of ULICP is programmed to compute large sections of a suite of logs by selecting zones automatically and then performing all pertinent computations on a data point by data point basis within each zone.'.' An entire suite of logs can be processed in this manner with very little manual intervention. Sufficient programming logic is available so that each log analyst can request computations pertinent to his area. These requests are made by simple additions or deletions of information on the input header cards. Hence, the log analyst is always in complete control of the computation process. The evaluation of a suite of logs requires pre-editing, digitization, computation, presentation of results and interpretation. Work by the log analyst is reqilired only in pre-editing and interpretation. Thus, he is allowed more time for comprehensive interpretation, rather than calculation. For continuity, the discussion of ULICP is organized sequentially: pre-editing, digitization, computation and presentation of results. DISCUSSION PRE-EDITING The extent of pre-editing prior to computation is dependent on the format of the original data. For analog prints, it requires inspection, correlation and editing of the logs, plus the entering of required data an special forms. For digitized data such as magnetic tape field recordings, only the special forms are necessary. The process for analog prints will be given here. The inspection and correlation process involves the selection of sections for digitization and the correlation of the traces to a common depth. To decrease the cost of digitization, traces that exhibit large variations in shale formations can be redrawn to a non-zero baseline. The next step is to enter all pertinent data on the input header cards. The header cards presently used for ULICP are presented as Figs. 1 through 6. Cards 1, 2, 3 and 4 (Fig. 1) are defined as the Main Header Cards. They describe the particular well for output identification and give basic information. Cards 5 through 15 (Figs. 2 through 6) are defined as the Block Header Cards. As such, they define the log types and the interpretation parameters for the block of data immediately following. Cards 1 through 10 are required for every computer run. Cards 11 through 14 pertain only to nuclear logs. Card 11 is required if any nuclear log is supplied, and cards 12 through 14 are required only when gamma-ray, density or neutron log data, respectively, are supplied. Card 15 (Fig. 6) must be supplied when cross-plot calculations are required. Either two- or three-component

Jan 1, 1967

By J. R. Martson

The arrangement of the larger furnace at the United Verde smelter, together with the boiler layout and connecting flues, is shown in Fig. 1. The important dimensions are given in the figure, and cross-sectional areas of combustion space, flues, etc., are recorded. The location and extent of the baffling in the boilers also are shown because of their importance in the interpretation of the data. Two boilers serve each reverberatory furnace. They are of the class M-26 Stirling type (rated at 713 boiler hp. each). Steam is generated at 178-lb. gage pressure at a total temperature of 528" F., from feed water at a temperature of 113" F. The feed water is condensate from turbogenerators plus make-up softened by the lime-soda process. The make-up is rather large in amount as it must match the amount of steam consumed in reciprocating blowing engines and the like, which are not served by surface condensers. As a result the boiler feed water has a hardness of 1.5 to 3.0 grains per gallon, but this results in the formation, during six months to one year of boiler operation, of scale only of "eggshell " thickness or less. The boilers are set at the same elevation as the tapping floor of the furnace, which results in the introduction of the waste-heat gases at the top of the front bank of tubes and necessitates the inversion of the usual baffling arrangements. The boilers are equipped with valve-in-the-head soot blowers, which keep most of the dust blown off the surface of the tubes, but it is necessary to supplement the soot blowers by high-pressure air lances, inserted by an attendant through side doors in the boiler setting. Deposits of coal ash and of dust from the furnace charge accumulate in the flues between the reverberatory furnaces and the boilers and this necessitates cleaning of these connecting flues by hand during the greater part of one of the three 8-hr. shifts during each 24 hr. This cleaning operation requires the opening of clean-out doors, which, of course, has some effect on the yield of steam. Revebberatory Furnace Practice The United Verde furnaces are fired with pulverized coal of sub-bituminous type of which the screen and chemical analyses are given in Table 1.

Jan 1, 1934

By D. H. Thompson, A. W. Tracy

Season-cracking is a type of failure of brass that results from the simultaneous effect of stress and certain corrodants. The object of this paper is to present data that will aid in a more complete understanding of the mechanism of season-cracking and related phenomena. Results presented show that certain high copper alloys are susceptible to season-cracking or stress-corrosion cracking, and possible explanations are discussed. Starting at least as far back as 1906, many papers have been devoted to this subject but the symposium1 held in Philadelphia in 1944 is the richest source of information. In order to study season-cracking, several of the many variables were held constant so as to learn the effects of others. Season-cracking is generally understood to refer to the corrosion cracking of brass having internal stresses;²,³ it is a special case of the general stress-corrosion cracking. Inasmuch as applied stresses are more readily produced and controlled, they were used exclusively in this research and the resulting phenomenon must he called stress-corrosion cracking.²,³ Only constant tensile stresses were used. The agents believed to be most frequently responsible for season-cracking are ammonia. amines and compounds containing then]. Both moisture and oxygen also appear to he necessary. Therefore, an atmosphere containing ammonia, water-vapor and air was selected for these tests. Briefly, the work consisted of exposing sheet metal specimens, having a reduced section ¼ by 0.050 in., of copper-base alloys to the effect of static tensile stresses between 5,000 and 20,000 psi and simultaneous contact with a. continuously renewed atmosphere containing 80 pct air, 16 pct ammonia and 4 pct water vapor at 35°C. The gas mixture and the speci- mens were maintained above the dew-point. The time-to-failure in minutes was the primary measure of results. In order to limit the experiment to finite time, it was considered that a specimen which had neither failed nor undergone microscopically detectable cracking in 40,000 min. (4 weeks) while under a stress of 10,000 psi or more could be considered immune to cracking. This is merely a convenient limit and is not to be considered proof of immunity. Supplementary tests in the absence of stress using weight loss or microscopical appearance as measures of attack were made. Apparatus The apparatus used in this research is shown in Fig 1. To facilitate the description it may conveniently be divided into six parts: stress-producing units, test chamber, gas train, electrical controls, timers and gas analysis device. A stress-producing unit is shown in an exploded view at the left in Fig 2. At the right is an assembled unit with a specimen in place in the lower portion; it is this part that remains in the ammonia atmosphere during a test. The upper part contains a spring, a central threaded rod, a large nut and necessary washers, pins, and so forth. Stress is produced in the specimen by screwing down the top nut against the spring, thus putting a tensile load on the central rod and so on the specimen. The wrench that turns the nut by extending through the upper cap, is seen at the upper right of the figure. The magnitude of the load is gauged by measuring from the pin that extends through the side of the tube, to a fixed point on the large flange. Measurement is made with a vernier beam caliper, shown at the right of the figure. The necessary spring compression to give a desired stress is calculated from the calibration curve of the spring and the dimensions of the specimen. The test chamber, center Fig 1, consists of a thermally insulated steel box 32 in. long by 10 in. high by 7 in. wide. A horizontal baffle reaching nearly to each end divides the chamber equally. Below this baffle are inlets for air and ammonia, a heating coil and a fan. Thus the gases are warmed and mixed in the lower level and flow past the specimens in the upper level. A thermo-regulator and thermometer project into the upper space. The top is pierced by 12 ports flanked by 3/8 in. threaded studs. A test starts when a port is opened and a unit containing a stressed specimen is thrust through it and bolted down against a neoprene gasket. The test chamber is held at 35°C. The gas train, right rear Fig 1, carries ammonia and air continuously to the test chamber. Tank ammonia passes through two reducing valves, a needle valve, a flow meter and into the test chamber. The air from either the plant compressor or a small laboratory compressor passes through wool towers and flow controls to the flow-meter. It then bubbles through water at 34°C and through a heated line to the test chamber. Electrical controls, left rear, Fig 1, provide rectifiers and mercury relays for the test-chamber and humidifier-heating-control circuits and outlets for

Jan 1, 1950

Jan 1, 1908

By R. B. Snow

Inclusions revealed by the ultrasonic inspection of forgings, slabs, and blooms cause costly diversion or rejection of the product. Most of those inclusions are so large that they should have floated out of the liquid steel soon after teeming and been removed when the top discard was taken from the ingot. To investigate the source of the relatively large inclusions found in the body portions of ingots, a large forging ingot was examined from top to bottom along the centerline, and special studies were made of open-hearth and BOP ingots. A study of the inclusion distribution in the as-cast 134-inch-diameter forging ingot revealed only a few inclusions larger than 15 microns in the body of the ingot. Larger inclusions may be formed by entrapment of rising inclusions in large falling dendrites rather than by the precipitation and agglomeration of oxides from the liquid steel-dendrite interface during solidification. The original top crust of the ingot investigated broke away from the hot top and sank to the bottom during the solidification process, as indicated by entrapped inclusions found in a band 12-1/2 inches above the stool. A change in the hot-top insulation practice on subsequent ingots to insure the integrity of the top crust has produced clean ingots. A ZrO2 tracer was added to the hot-topping compound and to the top surface of open-hearth and BOP ingots after teeming. The tracer was found in large inclusions in slabs and blooms from these ingots. Large inclusions in the body of ingots appear to be related to disturbances of the natural freezing and shrinkage processes in the hot- top region of the ingot.

Jan 1, 1972

By N. A. Gokcen, S. Fujishiro

The dissociation pressure of Cr3C2 has been measured in the range of 1908" to 2237°K by means of graphite Knudsen effusion cells. It has been found that Cr3C2 vaporizes according to the following reaction: 1/3 Cr3C2 (s or 1) = 2/3 C (graph.) + Cr (g). The equilibrizcm pressure, P, of Cr (g) is found to be log Ps=- - (21,194/T) + 6.525 over solid Cr3C2 and estimated as log P, = - (19,535/T) + 5.76 over liquid Cr3C2. CARBIDES of chromium are of great importance in alloy steels and cemented carbides. The published data on their therm odynamic properties at high temperatures, however, are meager. The heat capacity and change in entropy of Cr3C2 were determined calorimetrically by Kelley and Moore1 in the range of approximately 50" to 300°K, and by Oriani and Murphy2 from 297" to 1188°K. The standard entropy of Cr3C2at 298.15°K, obtained by Kelley.7 was later confirmed by DeSorbo.4 Equilibrium in the reaction was investigated by Boericke.5 A recent tabular summary

Jan 1, 1962

By N. A. Zeigler

GRaphitization phenomena occurring in solid cast iron have principally been studied from the angle of the reactions taking place during annealing of white castings in the manufacturing of malleable iron. The selected bibliography at the end of this paper presents the high spots of the published information in this field. Graph-itization of gray iron upon reheating has received much less attention, primarily because only on rare occasions is this material subjected to any kind of industrial heat-treating. Moreovcr, articles made from gray iron are seldom used commercially at temperatures when any graphitization can take place. When used in such conditions, it is assumed that the articles can be replaced at frequent intervals, which can be afforded because of the low cost of gray iron. However, there is at least one commercial process in which articles made from gray iron, during their manufacturing processing, are subjectcd to rather high temperatures; that is, manufacturing of cast-iron enamelware, which is glazed at about 1600° to 1700°F. (870' to 930°C.) From practical experience, it has been found that one of the convenient and economical compositions of gray iron suitable for enameling is, in round figures, as follows: Si, 2.50 per cent; Mn, 0.35; S, 0.07; P, 0.80; T.C., 3.35; C.C., 0.70. Since this iron usually is cast into thin-walled sections, the percentage of com- bined carbon in it is relatively high. Upon heating in the enameling furnaces, this combined carbon graphitizes, which causes permanent dimensional changes of the articles. Obviously, from practical considerations, it is desirable to maintain these dimensional changes as constant as possible. In the course of experimentation with this iron, two series of experimental heats were prepared in which the manganese to sulphur ratio of the standard cupola metal was offset by ladle additions of: (I) progressively larger amounts of sulphur, and (2) progressively larger amounts of manganese. Each one of these ladle charges was cast into experimental plates 8 by 4 in. and about 5/16 in. thick. All told, 13 ladle charges were thus treated. All of them are listed in Table I, together with their chemical analyses. It may be noted that the manganese to sulphur ratio in these samples ranges between 1.2 and 30.2. Every one of these compositions was subjected to thermal allalysis, using an automatic, self-recording differential dila-tometer. The specimens used in this instrument are 50 mm. long and 4 mm. in diameter. During the dilatometer cycle they are kept under a vacuum of about 3 microns. Each one of them was subjected to a thermal cycle by heating it to I830°F. (1000°C.) in 3 hr. and cooling to room temperaturc in 5 hr. Figs. I, 2 and 3 present three automatically recorded dilatometer curves for irons: Serial No. I (normal composition), Serial No. 6 (high sulphur), and Serial No. 13 (high manganese). All three of these figures are

Jan 1, 1945

By S. J. Hruska

Rate expressions for the formation of two-and three-dimensional nuclei on foreign substrates are developed, taking into account previously neglected contributions to the standard Gibbs free energy of formation of critical nuclei. The temperature dependence of critical super saturation data predicted using these expressions is in accord with data for cadmium on copper and sodium on CsCl. EXPERIMENTAL data on the heterogeneous nuclea-tion of metal crystals from the vapor phase1&apos;2 exhibit the temperature dependence predicted by a nucleation rate equation derived by Pound et al.3 In their treatment, the critical nuclei are visualized according to the Volmer4 model as cap-shaped (three-dimensional). Accordingly, it seems desirable to compare these data with a nucleation rate equation which is derived on the assumption of disk-shaped (two dimensional) nuclei. Further, Lothe and Pound5 have recently shown that the standard Gibbs free energy of formation of these critical nuclei contains a contribution which has heretofore been neglected. Thus it is necessary to re-examine these nucleation data using a rate equation which contains this contribution. The van&apos;t Hoff isotherm relates n(i), the concentration of nuclei of critical size i (i = number of atoms), to nil), the concentration of adsorbed single atoms: where standard Gibbs free energy of formation of critical nuclei given by is temperature insensitive and is the bulk free energy change/volume of transformed material], T = substrate temperature and k = Boltzmann&apos;s constant. Previously,3 was determined by considering only the contributions of bulk and surface free energies in transforming i atoms from the population nil) to a cluster of i atoms. It has been shown5 that this procedure does not take into account the free energy contribution arising from the multiplicity of sites, q, where the clusters can be situated. If this contribution, -kT In q/n(l),is added to iG3 [Note that this increases n(i) by a factor q/n(l).] Since the above does not affect the remaining terms in the rate expression of Pound et al., the details are referred to their paper. The resulting nucleation rate is If the experimental AGV and T values at some common value of are employed, a plot of vs T(ln C3/l + In p&apos;) should yield a straight line of slope k/B<p and intercept . The corresponding plots for / = 1 nucleus per sq cm sec and C3 = 1018 are shown in Figs. 1 and 2 for cadmium on copper1 and sodium on CsCl2 and the values of obtained therefrom are entered in Table I. It is apparent that the data yield reasonable straight lines with about the same scatter as found using the equation of Pound et al. When the configuration of minimum free energy for a nucleus is a circular monatomic layer, the standard free energy of formation is

Jan 1, 1963

By William P. Prof. Blake

WHEN we consider the efforts made in Europe to promote the physical and moral well-being of the working classes, the question is suggested whether in this country, where, theoretically, every man is peculiarly the arbiter of his own destiny, we may not be too prone to expect every man to take care of himself, and neglect to make those provisions for the welfare of the employed, demanded alike by enlightened economy and humanity. In the older countries, where the disproportion between capital and labor is greater, and the working classes are more dependent, their welfare largely occupies the attention of employers. The subject is involved in the problem of the just relations of capital and labor, and we are rapidly approaching the time, if we have not already reached it, when a generous paternal interest in the welfare of the employed should be more generally manifested. It is a subject which is of special importance to mine-owners and engineers in this country, especially to those located in the coal regions. My own attention has been particularly directed to it by a visit made to the Hassard collieries, a few miles from Liege, Belgium, under the direction of M. Andrimont. This celebrated engineer has established a comfortable home for the miners near the mouth of the shaft of the mine. It has been highly successful and beneficent in its results, and may to a great degree be regarded as a, model for such undertakings. It is known as "Hotel Louise," this being the name of Madame d&apos;Andrimont, who laid the corner-stone of the building April 4th, 1871. The structure is of brick, upon three sides of a square, and

Jan 1, 1875

By William P. Blake

When we consider the efforts made in Europe to promote the physical and moral well-being of the working classes, the question is suggested whether in this country, where, theoretically, every man is peculiarly the arbiter of his own destiny, we may not be too prone to expect every man to take care of himself, and neglect to make those provisions for the welfare of the employed, demanded alike by enlightened economy and humanity. In the older countries, where the disproportion between capital and labor is greater, and the working classes are more dependent, their welfare largely occupies the attention of employers. The subject is involved in the problem of the just relations of capital and labor, and we are rapidly approaching the time, if we have not already reached it, when a generous paternal interest in the welfare of the employed should be more generally manifested. It is a subject which is of special importance to mine-owners and engineers in this country, especially to those located in the coal regions. My own attention has been particularly directed to it by a visit made to the Hassard collieries, a few miles from Liège, Belgium, under the direction of M. Andrimont. This celebrated engineer has established a comfortable home for the miners near the mouth of the shaft of the mine. It has been highly successful and beneficent in its results, and may to a great degree be regarded as a model for such undertakings. It is known as ((Hotel Louise," this being the name of Madame d&apos; Andrimont, who laid the corner-stone of the building April 4th, 1871. The structure is of brick, upon three sides of a square, and

THREE regional meetings are planned for this summer and fall following the spring meeting held under the auspices of the Iron and Steel Committee and the Ohio Section at Cleveland in April and in lieu of a general fall meeting of the Institute. Plans for all of them are maturing rapidly. Excellent programs and. interesting visits to points of local tech¬nical interest are already assured. THE SALT LAKE CITY MEETING This meeting will be under the auspices of the Milling Committee and the Utah Section. It will be one of the features of the joint convention held the week of August 22 to 26 with the Western Division of the American Mining Congress. The Congress will be responsible for the general arrangements and for the program on the first day. The following general committees have been appointed:

Jan 7, 1927

By J. Gurland

THE microstructure of sintered carbides consists of particles of metal carbides, such as WC and TiC, embedded in a metallic binder which is usually a cobalt—or nickel-rich solid solution. One of the important factors influencing the strength of the alloys is the degree of dispersion of the carbide particles in the binder matrix. While it is generally accepted

Jan 1, 1960

By Richard P. Sheldon

In the last several decades, techniques of data collection have been rapidly evolving. Automated spectroscopic techniques in the chemical analysis of rocks for example have advanced to the point that we can analyze samples faster than we can grind them. Remote sensors of LANDSAT give us intensity measurements in four color bands of every acre of the U.S. every 19 days. Common depth point seismic instrumentation systems used at sea for surveying and networks of seismometers arrayed around the country for earthquake studies likewise are generating vast amounts of data. These along with many other earth science data generating systems have caused a veritable data explosion. How do we deal with these enormous amounts of geologic data presently being produced as well as those produced in the past, and to be produced in the future? There is an immediate need to acquire and utilize past and present basic data in order to address today&apos;s national earth science problems. Also data being collected and stored now must be compatible with future data in order for us to be able to undertake the wide spectrum of analysis that must be made in the future. This is a big order! In order to organize and to be able to analyze these data, the USGS has embarked on a wide ranging program of compatible data base construction and the development of computer technology, based on interactive computing, to facilitate resource assessments and analyses. These activities are analogous to two sides of a coin. One side deals with the logic, philosophy, and mechanics of information storage and retrieval; and the other side deals with the sensible application of computer technology to the treatment of data. These

Jan 1, 1977

By Enrique Touceda

For a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At the outbreak of the war the firm decided to specialize in the manufacture of propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods of manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual blade mold formed, the pattern is then rotated on the spindle to the position for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this pratctice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface of each blade must be chipped to the templet and through this procedure chipped to such accuracy as will be required for a static balance. Inasmuch as the work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin of the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days of foundry work and about the same length of time for the machining. Through the use of the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity with any particular propeller-wheel design.

Jan 1, 1922

By Enrique Touceda

For a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At the outbreak of the war the firm decided to specialize in the manufacture of propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods of manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual blade mold formed, the pattern is then rotated on the spindle to the position for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this pratctice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface of each blade must be chipped to the templet and through this procedure chipped to such accuracy as will be required for a static balance. Inasmuch as the work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin of the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days of foundry work and about the same length of time for the machining. Through the use of the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity with any particular propeller-wheel design.

Jan 1, 1922

By R. H. Sweetser

The Committee on Evaluation of Coal for Blast-furnace Coke reports progress in the working out of the problem of evaluation. There has been no full meeting of the Committee but there have been several conferences with two or more of the members present, and the different members have expressed themselves freely on the five points that have been under consideration since the meeting of the Committee in New York on Feb. 16, 1932. The need of a method of coal evaluation, not only of coking coals but all other kinds, is obvious. Under NRA it becomes imperative that coals of the same size from the same seam be priced according to their variations in quality, especially in reference to cleanliness in respect to freedom from extraneous ash-forming materials. In looking over the correspondence that has passed between members of our Committee, it is evident that much of the confusion and misunderstanding would disappear if we could realize that practically all of the variations in value of coal from the same seam of coal are due to variations in the amounts of extraneous materials that are contained in the coal as it passes over the scales for shipment. It is not now a question with our committee as to the differentials in value, or in prices, between different kinds of coking coals or between noncoking and coking coals; our present problem is to arrive at the method for determining the scale of values of the coal from a certain coal seam according to the increase or decrease of extraneous ash and moisture from a predetermined base line adopted for that particular coal. The five points mentioned above are the same as discussed at the meeting in February, 1932, except that the temperature for determining the moisture content has been changed from 212" F. to 221" F., at the suggestion of Dr. A. C. Fieldner. The points are: 1. It is proposed that the coal industry adopt as a base line for evaluating all coals the analysis of the coal as it passes over the neighing device that determines the tonnage of coal bought and sold. 2. It is proposed that the Committee on Evaluation of Coal for Blast-furnace Coke approve the adoption of the base line for Pittsburgh seam coal presented by F. A. Jordan at the annual meeting of A.I.M.E.

Jan 1, 1934

By C. K. Leith, W. J. NEAD

(Glen Summit Meeting, June, 1911.) . ONE Of the most significant developments in the iron industry in recent years has been the discovery and opening of enormous reserves of low-grade ore in eastern and northeastern Cuba. The two principal fields are the Mayari and the Moa, situated on Nipe bay, in the Province of Oriente. A less well-known district of the same type is that of Baracoa, at the east of the island, and another is in Camaguey province in central Cuba. In the comprehensive estimates of the iron-ore reserves of the world, published during the summer of 1910 by the International Geological Congress in Sweden,&apos; these Cuban deposits are estimated at about 2,000,000,000 tons. Certain it is that the reserve is a large one. The Spanish-American Iron Co., the Juragua Iron Co. (Bethlehem Steel Co.), the U. S. Steel Corporation, and others have been active in this exploration.. The Spanish-American Iron Co. has established a port for the handling of these ores at Felton, has built a railway 16 miles to the ore-fields, and has opened up deposits for steam-shovel mining. Its expenditures have reached an aggregate of about $6,000,000 in preparation for the handling of these ores. Shipment of the ore to Sparrow&apos;s Point, Md., has begun and may be expected to rise to a considerable amount in the near future. The ore reaches this point at a cost per unit of iron considerably lower than Lake Superior ores, and the presence of a low percentage of nickel gives a desirable steel. It is not the purpose of this article to consider these ores from a commercial stand-point, but rather to discuss their-origin. If our conclusions are correct, they throw light on the character of the deposits which should have some commercial significance. 1 The Iron Ore Resources of the World, an inquiry made upon the initiative of the Executive Committee of the Eleventh International Geological Congress, Stockholm, vol. ii., p. 795 (1910).

Mar 1, 1911

By Merlin H. Aylesworth

THE subject assigned to me is peculiarly appropriate to the anniversary of the birth of Abraham Lincoln. If we applied to our present problems the ideals and methods of the Great Emancipator, the future of American institutions would be so definitely assured that there would be little need to discuss the matter. The only inquiries would relate to the pace of progress, not to the possibility of progress. As a nation we have grown more and more to revere the memory of Lincoln, to honor his character, to extol his teachings and to eulogize his concepts of democracy. We rec-

Jan 1, 1940

By W. M. Hirthe, E. H. Greener, D. R. McCann

It has been proposed1&apos;2 that, at low temperatures, point defects are a strengthening factor in inter-metallic compounds whereas, at high temperatures, the deformation is diffusion-controlled and, therefore, an increase in the concentration of point defects tends to soften or increase the plasticity of a compound. More recent investigations, including those of Bloem and Kroger&apos; on PbS, Kramers and smith4 on TiO, and Nadeau5 on LiF, have extended this concept to ionic crystals. Rutile (TiO2) is a tetragonal transition metal oxide which has a defect structure over at least the compositional range. The defect in near-stoichiometric rutile is either an oxygen ion vacancys or a titanium ion interstitial.&apos; This investigation does not contribute to resolving the defect question but either defect would satisfy the results obtained. Six specimens having the same orientation, see Fig., 1, utilized in an independent investigation1&apos; were cut with a diamond saw from a single-crystal boule purchased from the Linde Co. Three specimens were annealed in air at 1200°C for 4 hr and slowly cooled to room temperature in a period of 12 hr. The remaining specimens were reduced in a vacuum of l0 mm Hg at 1200°C for 4 hr and cooled at the same rate in vacuum. The reduced specimens were weighed before and after reduction and, assuming the weight loss to be oxygen, the corresponding oxygen-to-metal ratio is 1.998. All specimens were chemically polished and etched utilizing the techniques described by Hirthe, Adsit, and Brittain." The specimens were embedded in acrylic resin and mounted on a leveling vise in a Kentron micro-hardness tester. A 200-g load was applied to a Knoop indenter with a descent time of 18 sec and a dwell time of 20 sec. Eight indentations were made on a near (171) surface, approximately 3 deg from the (lii) plane, for each orientation of the major axis of the indenter relative to the crystal structure. The dependence of microhardness on orienta-

Jan 1, 1963