Search Documents

By E. D. McMurry

INTRODUCTION Before discussing the use of the free piston; it may be well to explain briefly the type of gas lift valves with which the loo] is designed to function. The gas lift valve ii nothing more or less than a small back pressure regulator. It; construction consists of an outer hous ing covering a seamless metallic bellows in such a way as in form a sealed pressure vessel or pressure dome. To the bellow* in attached a stem and to this stem is attached a .rating member. When the valve is run into the hole, a pre-delermined pressure charge is placed in the pressure dome. As shown in Fig. 1. the valve is furnished in four different major assem-blies. to accomplish good results in different types of wells. The valve is mounted on a pup joint (Fig. 2a) : the eoin-plele assembly is entered into the tubing siring at the desired location. Each valve is furnished with a revere flow check valve (Fig. 2-b) to eliminate any back wash through the mechanism. Valve action is as follows: At any time the casing pressure is allowed to exceed the pressure forces within the pressure dome of the valve, the valve simply opens and passes gas from the rasing annulus into the tubing. When the casing pressure forces arc allowed to bleed to a force less than the pressure force within the dome, of the valve. the valve closes. With this type of construction. it is possible to open and close the valve or valves at will from the surface, the medium of the gas pressure in the rasing annnlus. The cycle of operation is governed by a tine cycle motor valve, commonly referred to as a gas lift interutitter or gas life surfacr controller (Fig. 3). In actual practice. after the well is unloaded only one valve is in operation . . . all other valve.: remain in the closed position. On pre-determined time cycles, it is possible to open and close this operating valve at will, and to pass the desired amount of gas through this valve wheneler needed. This method of gas lift is widelv used and has been found In be very efficient. However, it has long been known that even greater efficiency would be obtained if it were possible to place Piston between the injected gas and the fluid head. The free piston which will be discussed here was designed to accomplish this end and has been found to do so with very satisfactory results. DESIGN AND OPERATION OF THE FREE PISTON Basically. the free piston consist- of a telescoping assembly in which are incorporated the various control and operating parts (Fig. A set of sleeve valves which are opened and closed by movement of the telescoping section is contained in the. tool. A cross section of the free piston is shown in Fig. 4-11, 'rile main body cotain- a seamless monel bellows of the same type as that generally used in pressure charged gas lift valves (Fig. 4-c), and a valve core to permit placing a pressure charge in the bellows before the free piston is placed in service. The bellows is the main control unit of the free piston and performs two function: 1. It governs the opening and closing of the sleeve valves. a.: dictated by the producing activities of the well in which the piston is operating. 2. In its normal position, it holds a rubber packer in an elongated position to permit passage of fluid between the packer and the tubing walls. The lower section of the free piston contains a hydraulic shock absorber which cushions the return of the tool to its

Jan 1, 1953

By J. L. Moriarty, Irving Johnson, H. M. Feder

The crystallization of ternary alloys has been studied as a coprecipitation phenomenon by measuring the substitutional carrying of trace metals with CeCd11 precipitating from liquid cadmium. The Doerner-Hoskins logarithmic distribution law has been found to apply in all cases; the coprecipitation coefficients obtained were: 1.48 (La), 1.06 (Th), 0.63 (Pr), 0.24 (Gd), 0.17 (Sm), 0.13 (U), 0.10 (Er), 0.09 (Sr). Li, Na, K, Ba, Y, Sc, and Zr were not measurably carried. It has been observed that coprecipitation was most extensive for those tracers which form with cadmium an intermetallic compmdnd isostructural with CeCd11 or closely related thereto. For these tracers an inverse relation between Solubility in cadmium and coprecipitation coefficient was noted. THE partition of impurities between the liquid and solid phases of a metal or a congruently melting intermetallic compound has been extensively studied by the methods of zone melting.' However, when the composition of a liquid alloy and of the solid phase crystallizing from it differ grossly, partition of an impurity cannot be investigated in this manner. Partition of the impurity under equilibrium conditions may be studied by investigation of the appropriate phase diagram and partition under nonequi-librium conditions may be studied by observation of coring in the solidified alloys.2 The nonequilibrium case is of special interest in metallurgical practice because many complex alloys are cooled too rapidly to permit the uniform diffusion of impurities throughout the crystallizing phase(s). With this in mind, the present study was undertaken to obtain quantitative data on the phenomenon of coprecipitation via substitutional solid solution in certain metallic systems. It will be noticed that rather than adopting metallurgical ter- minology we have chosen to refer to the partition of impurities during alloy crystallization as coprecipitation.3 In the terminology of coprecipitation the impurity is referred to as the tracer and the precipitating phase as the carrier. From aqueous solution, coprecipitation may occur as a result of adsorption on the surface of the carrier, by occlusion of the liquid within the crystals, or by solid solution of the tracer in the carrier. By slow cooling of liquid metallic solutions it is relatively easy to form large, regular crystals of the carrier; the effects of adsorption and occlusion may be minimized and the influence of substitutional solid-solution formation may be made to predominate. Previous studies of the crystallization of some intermetallic compounds4 and of copper, silver, and gold5 have shown that the coprecipitation or partition behavior of trace metals is entirely analogous to that observed in aqueous systems when ionic substitution occurs, e.g., coprecipitation of Ra++ with BaSo4. The precipitation of CeCd11 from liquid cadmium was chosen for study. This choice was influenced by the following consideration. If the relative atomic sizes of the tracer atom and the atom for which it substitutes determine the tendency to coprecipi-tate, then a lattice having a substitutional site of well-defined size would be desirable. In CeCd116 (structure type cubic BaHg117) the cerium atom is completely surrounded by a cage of twelve nearly equidistant cadmium atoms. Thus, atoms much larger or much smaller than cerium should be poorly accommodated in this cage. The choice of a lanthanide central atom allowed the testing of the size hypothesis with a number of lanthanide tracers which differed in size but not in valence or electro-negativity. EXPERIMENTAL The general technique of this investigation was to prepare a slightly undersaturated solution of carrier in liquid cadmium to which a tracer was added. The concentration of tracer was always so low that saturation over the entire temperature range investigated was never exceeded. The solution was cooled in a stepwise fashion. After each step a por-

Jan 1, 1964

By Charles E. Mann, Douglas J. Lootens, Rufino B. Bomasang

INTRODUCTION The economy of the Philippines, like that of many other developing nations, has been severely strained by the rapid escalation of imported crude oil prices over the past decade. In an effort to reduce its dependence on imported crude, significantly increased emphasis, both in the public and private sectors, is being placed on the rapid development of Philippine coal resources. This paper is designed to present an overview of the Philippine coal industry, its historical development, present status, and future potential. COAL RESOURCES AND RESERVES In 1977, a British consulting firm collated all available data on Philippine coal resources and estimated the total coals potential at about 0.9 to 1.4 billion metric tons (mt). In 1981, using more recent data the Philippine Bureau of Energy Development (BED) estimated the potential at 1.7 billion mt. The BED estimated the proven coal reserves at 257 million mt. These coal resources are scattered throughout the major islands comprising the Philippine archipelago. However, about 52 percent of the currently proven reserves are located in the tiny island of Semirara between the islands of Mindoro and Panay. About 25 percent is located in the Cagayan Valley in northeastern Luzon while 13 percent is located in Mindanao. The remaining 10 percent is scattered in the islands of Cebu, Samar, Mindoro, Negros, Polillo, Batan, and Catanduanes. The bulk of Philippine coal is sub-bituminous in rank. Some bituminous coal with coking properties has been reported in Malangas, Zamboanga del Sur in western Mindanao, and in Catanduanes, but the exact tonnages have not been accurately established. It is believed, however, to be at most 5 million tons. A little semi-anthracite coal exists in Malangas with the remaining unmined reserves estimated at a little more than one million tons. Table 1 shows the quality ranges of Philippine coal deposits.. Figure 1 shows the distribution of known Philippine coal resources PHILIPPINE COAL PRODUCTION In 1981, total coal production was 330,720 mt. Though modest by world standards, this was the highest production figure in Philippine coal mining history. This came from 25 mines, mainly small scale underground mines of capacities varying from 10 to 100 tons per day (tpd). The actual production capability was about 800,000 mt in 1981, but the producers had to scale down production to the level of local demand. Even then, some 50,000 tons of coal remained unused by year-end. The 1981 production came from the following areas: Cebu 224,751 mt (68%) Zamboanga del Sur 57,095 mt (17%) Semirara 13,222 mt (4%) Polillo 17,132 mt (5%) Cebu has always been the main source of Philippine coal production. Coal mining has been carried out in Cebu for the last 50 years, although it has been characterized by a very crude mining technology. Due to the limited size of coal deposits and complicated geology, however, Cebu's share of the total national production is expected to go down to only 10 percent by 1985. Except for Semirara's open-pit production, the balance of Philippine coal production comes from underground mines. These underground mines generally use room-and-pillar methods, except for those at Zamboanga del Sur and Polillo which use modified longwall methods patterned after those used in Taiwan. Due to the much higher mining recovery, most underground mines are now planning on switching to longwall. At Semirara, an open pit mine is now being developed for a one million ton per year capacity by 1984, and will then be the largest Philippine coal mine. While present earthmoving work is done with bulldozers, loaders, and trucks, the main coal extraction equipment will be bucket wheel excavators imported from Austria. PRESENT COAL UTILIZATION Existing coal production is sold mainly to coal- fired cement plants and power plants. The balance is sold to a sugar central, a coconut oil mill, a food processing plant, and two plants producing carbide and ferro-silicon alloys.

Jan 1, 1982

By J. Lohrenz, R. J. Francis, G. C. Clark

Compositional material balance methods have been extended to solution gas-gas cap-water drive reservoirs. Partial or complete pressure maintenance as well as reservoir repressuring by gas and/or water injection may be considered. Increrments of reservoir withdrawals and injections equivalent to a given time increment are used as the basic iterative step to allow the extension. An example field study shows how the reservoir volumes. extent of the water drive, and relative permeability ratio function may be estimated. Knowing these, the methods can be used to predict reservoir behavior. INTRODUCTION The compositional material balance is similar to conventional material balances in many aspects. The assumption of a pressure-homogenous reservoir with no transients is common to all conventional material balances1-1 although numerical methods are different. The compositional material balance also contains this assumption. Inclusion of phase equilibria directly in reservoir calculations is the key difference and improvement in the compositional material balance. A continuous account of the compositions of the reservoir fluids and effluents is determined. Calculations of fluid phases and properties can be based on these compositions. Excepting fluid phases and properties determined in this manner, the compositional material balance uses procedures exactly analogous to conventional methods. Brinkman and Weinaug5 and Jacoby and Berry6 have given compositional material balances for simple solution gas drive reservoirs; subsequently Jacoby and Berry' extended their procedure to include pressure maintenance by gas injection at constant reservoir pressure. This paper extends compositional material balance techniques to a more general combination drive reservoir with various types of pressure maintenance operations. The procedure for this extended compositional material balance and an example of its field application are presented. PROCEDURE The numerical calculations of this compositional mate- rial balance are performed on a high-speed digital computer. The most comprehensive case the present compositional material balance program can handle is a solution gas-gas cap-water drive reservoir with (1) water production, (2) water influx, (3) separate or commingled production from the oil and gas zones, (4) any surface processing arrangement including LPG and gasoline production, and (5) gas injection into the gas and/or oil zones." This description of the procedure applies to this most comprehensive case. Appropriate deletions in the procedure can be made for more simple mechanisms. ASSUMPTIONS In common with conventional material balances, the compositional material balance makes the following assumptions: (1) the total reservoir is at a uniform pressure at a given time; (2) the volumetric ratio of gas to liquid withdrawal at reservoir conditions is directly proportional to their mobilities; and (3) instead of assuming a pressure-dependent total gas-oil equilibrium, the cornpbsitional material balance makes a sianificantly different and more rigorous assumption as follows. Thermodynamic equilibrium exists for each component in the liquid-gas mixtures in the reservoir and in surface processing. These three assumptions are fundamental in the compositional material balance procedure. Other assumptions involve arbitrary simplifications of the reservoir mechanisms. This compositional material balance uses the following simplifying assumptions: (1) no bulk mixing occurs between the gas and oil zone; (2) total mixing occurs between any injected gas and the contents of the injection zone; (3) no in situ hydrocarbon liquid is produced from the gas zone; (4) no reservoir gas is retained behind any net bottom-water influx; (5) the residual saturation of hydrocarbon liquid at reservoir conditions behind any net bottom-water influx is constant; and (6) fluids retained behind any net bottom-water influx exert no further influence on the reservoir. These six assumptions are not fundamental. Modifications of the present procedure can be made for different assumptions of the reservoir mechanisms. THE TIME INCREMENT Previous compositional material balances have used a pressure increment for simple solution gas drive reservoirs"" and an increment of injected gas for pressure maintenance.' These increments are suitable for these simple cases. They are, however, inadequate for reservoirs with time dependent drive mechanisms including water drive. A time increment removes this inadequacy and is

By Ellis H. Gates

BENEFICIATION of the manganese oxide ores at Three Kids Mine near Henderson, Nev., has evolved over a period of years. Commercial application of the process is on a secure basis, and an effective working hypothesis has been formulated to help solve the problems encountered in flotation. An outstanding difference between the Manganese Inc. operation and other flotation processes is the necessity for high recovery of slime mineral values. Part of the manganese minerals in the Three Kids ore deposit occurs as primary slime or as minerals that are easily slimed by grinding. High recovery of this slime portion is essential to an economic overall manganese recovery. The aim of much of the research at Manganese Inc. was to recover these slimed and finely ground minerals by flotation. Early Agglomeration Processes: Tunbridge' in 1880, followed by Everson2 in 1886 and Cattermole" in 1904, discovered that under certain pulp conditions precious metals and sulfide minerals could be agglomerated if enough soap or oil were mixed into the pulp slurry. These agglomerated particles, Which under ideal conditions ranged from 1/16 to 1/4 in. diam, were recovered by screening, tabling, and hydraulic classification. Even flotation by air occluded in the agglomkrate particles by vigorous stirring was suggested. Cattermole nearly succeeded in getting his process into commercial operation, but it was finally abandoned, presumably because he could nat compete with the low reagent requirements of the new agitation froth process. Since Cattermole's time Christensen in 1921, Borcherdt4 in 1926, and Chapman and Littleford- in 1934 have attempted to apply the principles of agglomeration. In the light of current research at Manganese Inc. on conditioning of pulp at high energy input levels, it is interesting to note the variety of equipment such as tumbling mills, mixing drums, and shakers described by Borcherdt in his patent to produce the agglomerated particles. Ore Characteristics: Manganese in the Three Kids ore occurs as a 'complex mixture of manganese oxides commonly Known as wad. The manganese minerals have Been identified as psilorflelane, hollandite, coronadite, and pyrolusite with minor amdunts of rhodonite and rhodochrbsite. The ppincipal gangue miherals are quaktz, opal, kaolinite, montmoril-lonite, calcite, gypsum, fcelesitite, and barite. Most of the mangandse ore minerals are either porous and sponge-like in structure or soft clay-like masses composed of fine grained mineral particles approaching the size range of colloids. Consequently the ore minerals from the Three Kids mine have relatively large surface areas and high void content per unit weight. The specific area of various manganese ore samples measured at the California Research Corp. laboratories ranged from 32 to 58 sq m per g. The great surface area and high void content explains in part the unusually high reagent consumption required in the treatment of this ore. Current Milling Practice: At Henderson6 he ore is crushed to —1 in. and ground with rod mills in a closed circuit with spiral rake classifiers and cyclones. Sulfur dioxide solution is added to the pulp as it leaves the grinding circuit, immediately followed by addition of a reagent mixture of soap, oil, and wetting agent in the form of an emulsion. The reagents are initially well mixed into the pulp during their passage through centrifugal pumps to the conditioning equipment. All reagents are added prior to conditioning. The intense conditioning or mechanical stirring of the pulp, in which large amounts of power are consumed, is the principal difference between the flowsheet used at Manganese Inc. and a standard flotation circuit. As much as 38 kw-hr of energy per dry short ton of ore in a pulp containing 18 to 23 pct solids is used for conditioning. After conditioning, the pulp passes to a flotation circuit that consists of one roughing stage, a scav-

Jan 1, 1958

By H. M. Myers, J. E. Funk

The two-phase flow of a drilling fluid in a diamond drill bit is investigated by deriving and solving the steady-state continuity and momentum equations. Parameters in this analysis are rotational speed of the bit, local rate of addition of drill solids, non-Newtonian nature of the drilling fluid and drilling rate. The describing equations relate the flow and pressure drop to the design characteristics of the bit. The equations are integrated numerically yielding the flow-rate pressure drop characteristics for the bit, flow distribution in the bit and velocity and static pressure as a function of position in each flow channel of the bit. Results are presented for a particular bit design. This paper shows that under normal drilling conditions certain parameters may be neglected in the hydraulic calculations for a diamond drill bit. Therefore, shortened forms of the equations presented can be used to fit the proper diamond bit to the drilling fluid hydraulic system. INTRODUCTION Like the conventional bit, the diamond drill bit is a key component in the circulating system of a well. The conventional rock bit is fitted to the circulating system by selecting the flow nozzles which provide the system with the proper flow-rate pressure drop relationship. Fluid behavior across the face of the diamond bit must be better understood so the bit can also be fitted to the circulating system. Data from field-operated diamond bits are presently available and do yield some information regarding the flow-rate pressure drop relationship. However, the number of factors affecting this relationship is quite large. Drilling parameters and conditions such as bit penetration rate, bit weight and rotational speed are important. Moreover, flow channels in the bit are part of the cutting head, and introducing drilled solids into the flow channels reduces the flow area, causes additional drag and influences the pressure drop. Many tests would have to be performed if field tests were required to study all parameters which might influence fluid behavior in the bit. A logical approach to this problem is to investigate analytically the fluid behavior in the bit, including parameters that are present under normal drilling operations. This approach, which seems to offer the best method for future studies, is presented in this paper. Following is the general procedure. 1. Equations describing the most general flow channel are written and include the addition of drilling solids (which is related to penetration rate), rotation of the bit, design parameters of the bit and non-Newtonian properties of the fluid. 2. A typical bit is designed and the bit parameters are substituted into the equations. 3. Parameters are assumed (penetration rate, rotational speed of the bit, mud weight, etc.). 4. The describing equations are numerically integrated to obtain the pressure drop across the face of the bit as a function of flow rate. 5. The pressure-drop contribution of each component (friction, acceleration, etc.) is obtained from the numerical solution, and those factors which largely influence the total pressure drop are identified. Classifying the drilling fluid is important in establishing the friction factor relationship since the frictional pressure losses are the main contributors to the total pressure drop. High-density drilling fluid is commonly assumed to be a Bingham plastic. 1-3 Govier4 presented a method for selecting a friction factor in the laminar flow region from the rheology properties of the mud and a modified Reynolds number. Metzner5 presented a criterion for selecting the friction factor in the turbulent flow region. The bit design used in conjunction with the solution of the equations has divergent flow channels. Stall, which is the backflow of fluid in the channels due to eddies that occur on the outer perimeter of the flow stream, can occur in these divergent channels (or diffusers). When stall does occur the static

By L. J. Erck, T. E. Ban

A discussion of laboratory procedures used to determine pellet quality and to simulate handling and firing conditions. Strength-temperature relationships in pelletizing; effect of chemical additives on agglomeration; and crushing, abrasion, and impact resistance of the pelletized products are discussed with respect to five different iron ore concentrates. IN most routine experimental work on products and processes, method:; of operation and product evaluation are established from accurately controlled laboratory tests. With particular emphasis on the pelletization of fine iron ore concentrates, standardized procedures of laboratory production and product testing have been established at Cleveland-Cliffs Iron Co. Research Laboratory at Ishpeming, Mich. A program of this nature was used for investigating the agglomeration characteristics of various iron ore concentrates. The factors which control the process were studied and subsequently controlled for these investigations. Pelletizing as applied to iron ore agglomeration involves the preparation of spheroidal masses from a fine moist concentrate, followed by high-tempera-ture firing to produce a final product. The preparation of moist spherorids is generally designated as balling. This produces the so-called green pellets or balls. After, these have been fired they are called pellets. Balling is accomplished by rolling moist concentrates in a revolving drum until small spheroids form by a snow-balling action. These balls are then heated in a shaft furnace, or a modification of this device, to a temperature high enough to cause agglomeration within the individual balls while they descend countercurrent to hot oxidizing gases. By this process the lour strength balls are converted through various chemical and physical-chemical processes into hard pellets. With correct balling and firing, the pellets are strong, resist abrasive action and handling treatments, and provide a suitable blast furnace and open hearth feed. In 1950 Tigerschiold and Ilmoni developed a working hypothesis to explain the formation and stability of green pellets.' Their work was presented on the basis of geologists' discoveries concerning the soil-water system and C. V. Firth's early postulates of green pellet formation.' Fundamental reactions oc-curing within fired pellets have been described by Cooke and Ban, who showed the microstructure changes caused by different firing temperatures." All these investigators have provided scientific clarifications of agglomeration by the pelletizing process and have opened avenues for greater development. Mineral grain growth and ceramic bond formation are the two basic phenomena imparting coherency to particles within a fired pellet of iron ore. Each of these is established by the transfer of thermal energy to the mineral particles. Grain growth mechanisms are chiefly physical reactions wherein smaller particles consolidate into larger ones, with resulting decrease in surface energy conforming with the second law of thermodynamics. Ceramic bond formation is a chemical reaction usually between basic and acid metallic oxides of the gangue and ore minerals. CaO, MgO, A1203, and FeO of Fe3O4, react in varying proportions with SiO, or Fe2O3, to form a great series of compounds or amorphous solid solutions. These product bond iron mineral particles together by a bridging action or by direct reaction with the surfaces of the particles. The result of the grain growth-ceramic bond formations is a consolidated, coherent compact of gangue and iron minerals formerly held together by much weaker bonds of interstitial water and forces common to dry, unconsolidated particles.4 With respect to iron ore agglomeration, these high temperature bonding reactions have been described by Schwartz, who referred to the bonds in sinters," and by Cooke and Ban, who referred to the bonds in fired pellets." The extent of the bonding phenomena and the consequent strength of fired pellets is governed by

Jan 1, 1954

By R. Grierson, R. N. Parkins

The m.echanica1 properties, at high lzomologous temperatures, of the intermetallic compounds InzBi and Mg17A112 were measured as a .function of temperature, applied strain rate, previous thermal and mechanical history, and composition. Mgl,Al12 was investigated ilz compression, whereas Zn,Bi was investigated in tension. A decrease inflow stress with increasing strain was observed jor both alloys. The results obtained are discussed in terms of the dislocation-multiplication processes in these materials. MANY intermetallic compounds are reported to undergo a brittle-ductile transition at high homologous temperatures.' There is evidence in the literature that some of these compounds exhibit a large yield drop when plastically deformed.'j3 Both of these forms of behavior are shown by the covalent elements germanium and silicon4,5 and also by certain ionic compounds.8 The present work is a study of the deformation, at high homologous temperatures (>2/3 Tm), of two intermetallic compounds, In2Bi and Mg17Al12. InzBi has a disordered hexagonal structure7 (c/a = 0.598) and a solubility range of 32.3 — 33.2 at. pct Bi.8 It has a melting range from 72° to 89°C. Mg17Al12 has an ordered bcc (A12 type)7 structure and exists over the range 50 to 60 at. pct Mg8 with a melting range from 437° to 462°C. We have been unable to find any reference to previous investigations of the mechanical properties of BiIn,. Novikovg has reported that cast samples of Mg17A112 show ductility, when bend-tested, at temperatures above 380°C. EXPERIMENTAL Ingots of In2Bi and Mg17Al12 were melted under an argon atmosphere and cast, in situ, in a graphite crucible. The materials used were of 99.99 pct purity. The alloys prepared contained 66.9 at. pct In in the case of In2Bi and 58.4 at. pct Mg in the case of m17A112. The ingots were homogenized and then extruded. Two-in.-diam Mg17Al12 ingots were extruded at 375°C to give 3/8-in.-diam rod. The rate of formation of this rod was 0.25 in. per min. One-in.-diam InzBi ingots were extruded at 20°C, using a rate of 1 in. per min, to give 1/8-in.-diam rod. In both cases the extruded rod had a recrystal- lized, fine-grain, structure. (For Mg17Al12, d = 11.2 µ; for BiIn2, d = 22 µ.) Mechanical-property determinations were made in a hard-beam machine, in tension in the case of In2Bi and in compression with Mgl7Al12. The tensile tests were on specimens having a gage length of 1.1/2 in. and a diameter of 1/8 in. The compression tests on Ml7A112 were on specimens of 3/8 in. diam by 3/8 in. high and the ends were coated with poly-tetrafluorethylene to minimize friction. RESULTS In2Bi. Fig. 1 shows, particularly at the higher applied strain rates, that In2Bi exhibits a marked yield drop as the deformation increases to about 2 pct, after which the material shows neither hardening nor softening up to 15 pct strain. The magnitude of the yield drop, the stress in the region of flow under constant stress (the stress plateau), and the 0.5 pct proof stress were all dependent upon the applied strain rate according to an expression of the form

Jan 1, 1965

By R. V. Smith

The theory for unsteady radial flow of gas, as simplified by Aronofsky and Jenkins, has been reviewed and compared with actual well performance. This study indicated that the theory should be modified by the introduction of an empirical "rate of flow" function "Y(q)". The expansion of the theory on the flow of gas to include a Y(q) term bridges the gap between the theory of unsteady-state flow of gas and actual gas-well behavior. Apparently, the Y(q) term is a function only of the rate of flow for a given well. The completion factor or skin effect is associated with the Y(q) function in such a manner that at least two or more sets of drawdown or pressure build-up tests are needed to separate the Y(q) function and the completion factor. Since the Y(q) function used in this report represents an energy loss dependent on rate of flow near the well-bore of a gas well which is in addition to the loss required by Darcy's law, the Y(q) function is related to the exponent of the back-pressure curve for a gas well. Techniques and equations are presented which permit the estimation of stabilized and "short-time" deliver-abilities. INTRODUCTION The published theory of radial unsteady-state flow of gas through porous media may be divided into papers1-" which use Darcy's law as a premise and other papers4-7,16-10 which recognize that Darcy's law may not hold for flow into gas wells. Miller8 compared theory based on Darcy's law with actual gas-well behavior and concluded that flow into gas wells deviates from Darcy's law. Houpeurt4,5 in a thorough investigation of flow into gas wells concluded that the flow rate into a gas well is proportional to the difference between the squares of upstream and downstream pressures elevated to a power between 1.0 and 0.5. Houpeurt also concluded that the deviation from Darcy's law is caused by irreversible, kinetic energy exchange between the flowing gas and the porous media. Tek9 presented a complete evaluation of the flow problem in gas wells. Several investigators state that the inclusion of gas compressibility into flow equations based on Darcy's law does not begin to explain the flow problems suggested by gas-well behavior. For many years, natural-gas engineers have realized that gas wells by actual test exhibit behavior which cannot be explained entirely by Darcy's law. Many tests on gas wells have indicated that a value of 0.85 for the exponent in the back-pressure equation is a fair average for many wells. However, Darcy's law either for steady or unsteady-state conditions indicates that the exponent should be 1.0. The purpose of this paper has been to examine this deviation from Darcy's law and to present a reasonable mathematical means of evaluating the deviation. The method presented in this paper combines previous theory with an empirical function to provide a description of gas-well behavior. All equations in this report are for constant terminal-rate-of-flow conditions. While present methods of testing wells usually are not based on this concept, they are believed to approach the constant terminal-rate conditions closely in many tests. However, several gas wells were tested by holding the rates of flow constant in order to approach more closely the constant terminal rate of flow; the results confirm the concepts presented in this paper. REVIEW OF THEORY FOR UNSTEADY-STATE FLOW OF GAS The basic partial differential equation for the flow of natural gas has been given in technical literature; the equation for a cylindrical reservoir with the well in the center is

By A. Lubinski, J. E. Hansford

Rotating drill pipe passing through dog-legs suffers fatigue damage due to cyclic bending stresses. Curves of the cumulative fatigue damage incurred in either steel or aluminum drill pipe going through Such dog-legs are presented. These curves provide means for properly planning the rate of angle build-up in directionally drilled wells and allow discarding of drill pipe which has been fatigue-damaged in dog-legs. INTRODUCTION Drill pipe which is subjected to bending as it rotates, experiences a cyclically varying bending stress. If this bending stress is sufficiently large, the drill pipe is fatigue-damaged by each revolution, and ages as fatigue damage accumulates. Drill pipe can be bent intentionally, as in the case of directionally drilled holes, or unintentionally due to unde-sired changes in hole direction caused by variations in formation properties, weight on bit, etc. These changes in hole direction, whether intentional or unintentional, are called dog-legs. The theoretical limits of dog-legs which are permissible before the drill pipe begins to fatigue can be calculated.' However, in wells where the maximum permissible dogleg is exceeded, the concept of cumulative fatigue damage can be used to estimate damage suffered by the drill pipe. This concept has already been used to estimate the cumulative fatigue damage of drill pipe due to drilling vessel roll.' The purpose of this paper is to extend the usage of the cumulative fatigue damage concept to drill pipe in doglegs, and to draw conclusions which may be beneficial in preventing numerous frustrating and expensive drill pipe failures. FATIGUE OF STEEL DRILL PIPE IN IDEALIZED GRADUAL AND LONG DOG-LEGS It is taken for granted that, if necessary, the reader will become familiar with the definitions and concepts which follow by examining the reference cited in each case. For Ref. 1, it will suffce to read only through the section Abrupt Dog-Legs. 1. Concept of the two extreme kinds of idealized doglegs: gradual and long dog-legs and abrupt dog-legs,' 2. Concept of why the bending moment in drill pipe un- der tension is the largest in the vicinity of the tool joint,' 3. Concept of why dog-leg severity which drill pipe can withstand decreases with an increase in tension,' and 4. Definition of the rate of change of over-all hole angle (dog-leg severity)." Figs. 1 and 2 indicate the aging (fraction of life expended) of steel drill pipe passing through a gradual and long dog-leg. Both figures have a left-hand ordinate scale labled Length of Drill Pipe Below Dog-Legs. This scale can be used for cases in which the drill collar weight is applied to the bit and does not contribute to the tension in the drill pipe. It can be used for either 3 1/2-, 4 1/2- or 5-in. drill pipe. This is due to the fact that, if the drill collars do not contribute to the drill pipe tension, then the effect of pipe tension on bending due to a change in pipe size is nearly compensated for by a corresponding change in pipe rigidity. On the other hand, if drill pipe is rotated off bottom, then drill collars contribute to the tension in the drill pipe and this increase in tension is not compensated for. In this case, one of the three right-hand ordinates must be used (the one which corresponds to the correct drill pipe size). In the right-hand ordinates, tension should be understood as the weight in mud of the portion of the drilling string below the dog-leg, minus the weight on bit.

Jan 1, 1967

By Euclid P. Worden

In 1977, an article in World Mining1 reported a total of 2726 rotary blasthole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher. Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to reducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is best measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, there are five factors which affect the rate of penetration. They are: (1) bit selection, (2) weight on the bit, (3) rotary speed, (4) hole cleaning, and (5) formation properties. Of these factors, all but one may be controlled by the operator. Looking at any one in detail may reveal possible improvements in the system. One of these factors -- proper hole cleaning - will be discussed in this paper. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in redrilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole. In an in-depth study of the cleaning of large diameter holes, Allen2 reports that horizontal air velocities of 38.10 m/s are necessary to prevent the saltation of drilled cuttings on the bottom of the hole. The exact flow pattern on the bottom of the hole, however, is not generally known. The air leaves the bit through the jet nozzles and the mouths of the cones, but where it goes from there is uncertain. This problem should be investigated by the bit manufacturers because they can best utilize the results of such an investigation to provide a more effective product. Some work has been initiated in this area and competition will probably increase its intensity. Bailing velocity is the best criteria to measure the cleaning of the hole, including the bottom, and is the factor on which efforts toward improvement must be concentrated. The first consideration is "What should the bailing velocity really be?" In drilling deep holes for oil and gas, 15.24 m/s is the generally accepted figure. In blasthole drilling, the figures of 25.40 m/s for average rock to 35.56 m/s for iron ore were first mentioned by Capp3 in 1962. The recommendations are the same to this day. A number of questions could be asked in regard to the apparent disparity between these two sets of figures. Various investigators have derived formulas which support one or another of these criteria. A thesis on the subject was written by Alexander4 who derived a formula based on research which resulted in velocities in the lower end of the ranges quoted previously. He set out to compare this figure to laboratory tests and his tests indicated that the velocities given by the derived formula appeared to be high.1 Perhaps the best reason that the 25.40 to 35.56 m/s range has been used, is that these velocities seem to work. Below the accepted figures, low bit life and slow penetration rates occur. Above these figures, increasing amounts of abrasive wear on the drill pipe and stabilizers seem to appear. There is a fallacy to this entire approach, however. The entire velocity calculation is made using nominal bit and pipe sizes and compressor deliveries with no compensation made for losses in the system. Perhaps an examination of some of the things that are not presently considered could lead to some practical improvements in the operation.

Jan 1, 1980

By G. T. Smith, R. C. Moyer

Cadmium, along with other impurities such as lead, gallium, germanium and indium, is characteristically found associated with zinc ores, the average ratio of zinc to cadmium being about 200 to 1. The increasing demand for cadmium has led most zinc producers to develop a means for its recovery. The separation and recovery of this byproduct constitutes an important development in the metallurgical field. Zinc sulphide concentrates, principally from domestic sources, are processed at Donora Zinc Works and they assay approximately 60 pct zinc, 30 pct sulphur, 0.37 pct cadmium, and 0.8 pct lead. Concentrates are roasted to convert zinc sulphide to zinc oxide. Sulphur evolved as sulphur dioxide is used to manufacture 60º Baume sulphuric acid by the lead chamber process. The roasted calcine is sintered to remove the remaining sulphur and volatile impurities. Fume from the sintering machines is collected by Cottrell pre-cipitators and sent to the Cadmium Department for cadmium removal. The sintered product, a crude zinc oxide, is then mixed with coke and salt and charged into horizontal retorts for reduction to zinc metal. Furnace residues are then passed through a Waelz kiln which recovers practically all of the remaining zinc as an oxide. This oxide is collected by Cottrell precipi-tators and returned to the sintering plant for further processing. The following discussion covers operating procedure, and equipment used in the Cadmium Department for the manufacture of cadmium and its byproducts. (See attached Flow Sheet, Fig 1.) The production of cadmium may be divided into several steps, each of which will be discussed separately. These steps are as follows: 1. Raw Materials—Sinter Plant Cottrell dust, acid sludge and sulphuric acid. 2. Sulphating—Separation of lead. 3. Purification—Separation of impurities other than zinc. 4. Precipitation—Separation of cadmium from zinc. 5. Briquetting—Preparation of sponge for charging to furnace. 6. Smelting—Distillation of cadmium metal. 7. Remelting—Casting into commercial shapes. 8. Recovery of Rare Metals—Separation of germanium, gallium and indium. Raw Materials The raw material, or Sinter Plant Cottrell dust, from which the cadmium is manufactured, is recovered by Cottrell units collecting fume from two Dwight-Lloyd sintering machines. An average analysis of this dust is 36 pct zinc, 1.5 pct sulphur, 17 pct lead, and 5.5 pct cadmium, with associated elements in smaller amounts. A lesser tonnage of material removed from the sintering machine fans, and called fan cleanings, is also treated for cadmium. It is lower grade material and analyzes approximately 41 pct zinc, 1.2 pct sulphur, 14 pct lead, and 4 pct cadmium. Cottrell dust and fan cleanings are delivered to the Cadmium Department by monorail crane in bell-bottomed dump buckets. Acid sludge and 60" Bauine sulphuric acid are received from the Acid Department. The acid sludge is a mixture of lead sulphate, sulphuric acid and zinc sulphate, and is recovered mainly from the floors of the acid chambers or storage tanks. The acid sludge is delivered to the Cadmium Plant in a lead lined bucket. The 60º Baume sulphuric acid is delivered through a lead pipe to a lead lined storage tank. Sulphating Four well ventilated lead lined sulphating tanks, 8 1/2 ft in diam by 12 ft deep, are used. These are steel tanks lined with 20 lb lead on the bottom and 16 lb lead on the ides, equipped with Hastelloy side agitators. 15 hp motors drive 24 in. propellers at 450 rpm. There are water connections to stuffing boxes to keep sludge from entering the bearings. The tanks are covered with removable wooden lids and are connected to marine plywood

Jan 1, 1950

By Morris E. Fine, Richard A. Kloske

The stress-strain beha1,ior in tension of Au-Ag alloy single crystals containing nominally 1,3, 5, 95, 97, and 9.9 at. pct Ag was studied uS strain role and lektlperalure down lo 4.2K. A slrain aging yield hob lc,rrs observed on aging under stress in the temperature range 30° lo 75°C. The species diffusing to the dislocation is thought to be a divacancy-solute complex wilh /he. solute then pinning the dislocation by short-Range ovdering and possibly Suzuki locking. At room tempevullcve the critical reso1ved shear stress .follo~c.s an empirical equation of the form tc = A +Bc' where A and B are 90 and 420 ,g per sy mm tor gold base alloys and 60 and 510 g p~r sq )11ttz .tor si1ver base alloys. This strengthening was attributed to a long-range size ejtect. The alloy slrenglliening at i.2'K is greafer than at room temperature. The additional atrloutzf was altribuled lo a uwak skovl-range i?~levacIion between the solute and dislocallon cove. The activation energy .tor deformation a/ 4.Z0h7 decreases on alloying. 11 increases irr other fee systetns. hi the 5 at. pcl Air-Ag- alloy in pmvlicular there is very extensive easy glide and lavge overshooting- of the synmetry line at 4.Z°K. There is also u sharp decrease in the vale of. strain hardenitlg near the widdle of stage II with the new rate bezng abold the sarne as tlzal In easy glide. This uws attributed to a sudden reduction of activity on the pvitrrarg sgstertr. In Au-Ag alloys the critical resolved shear stress Tc. at room temperature is essentially a parabolic function of atomic concentration:' the 50 at. pct Ag-50 at. pct Au alloy is about 10 times stronger than the pure metals. This strengthening occurs in spite of the similarity in valence and atomic size. Solid-solution strengthening in fcc metals is characteristically greater at low temperatures than at room temperature. In Ag-10 at. pct Au and Au-10 at. pet Ag; r, (20.4K)/Tc (300°K) is 2.3 and 2.5. respectively.- compared to 1.2 in pure silver.3 Suzuki' and Flinn5 explained the alloy strengthening at room temperature as a combination of Suzuki locking and short-range order hardening. The agreement between the computed and measured strengthening was very good: however, in Ag base-A1 alloys Hendrickson and Fine6 concluded that Suzuki locking resulted mainly in a yield drop effect. Recent reviews of the solid-solution strengthening in fcc metals by Fleischer2 and Haasen8, 9attributed the strengthening at room tenl-perature to the combined effect of atom nlisfit and change in shear modulus 011 the long-range stress field surrounding a dislocation. The parameter used by Fleischer was The shear tnoduli of Ag-0 to 6 at. pct Au alloys were measured by Pur-wins. Labusch. and Haasen.In While addition of 4 at. pct Au caused an appreciable increase in the C,, elastic constant. there was a decrease on increasing the solute to 6 at. pct Au: C,, and C :: were not measured in the 6 at. pct alloy. The greater solution hardening at low temperatures implies the presence of short-range interactions between the solute atoms and dislocations These include size and electronegativity effects. Whether the extra alloy strengthening at low temperatures is due to locking or friction hardening is still a controversy."".' In the present research the stress-strain behavior of Au-Ag single crystals containing 1 to 5 at. pct Ag and 1 to 5 at. pct Au was measured vs strain rate and temperature down to 4.2' K. Particular attention was paid to yield drop effects. These have not been previously reported. PROCEDURES The alloys were supplied by the Engelhard Industries. Inc.. as strips 0.050 by 0.250 by 12 in. The compositions are given in Table I. Single crystals were grown under static vacuum using a traveling molten zone technique. Crucibles shaped to the size of the strips were made of high-purity graphite prebaked for 24 hr at 1100°C in vacuum. The crucible and its charge were placed in

Jan 1, 1970

By W. O. Philbrook, H. E. Burner, F. S. Manning

The equation of continuity for the hydrogen reduction of hematite in a fixed bed of closely-sized particles is solved assuming a flat velocity profile, negligible temperature gradients, md negligible axial diffusion. A kinetic expression from the literature is used which assumes the reduction process is controlled at the oxide-metal interface. The integral fractional conversion is computed, and the importance of particle diameter, flow mte, temperature, bulk axial diffusion, and inter- and intra-particle mass trarnsfer is predicted. Comparison with experimental data suggests one or more additional undefined variable(s) is significant. Equipment modifications are suggested for fidture experimentcll work. WITH the increasing desire to "design" the ore feed of a blast furnace, it has become necessary to define more quantitatively the process variables and to evaluate the extent of their control upon the reduction process. The bulk of the work reported in the literature has centered about the reduction of single particles; however, the blast furnace process more closely resembles reduction of a fixed bed than that of single particles. To simplify this analysis, the isothermal reduction by hydrogen of a natural hematite in a fixed bed of closely-sized particles is examined. With appropriate modifications in the kinetic and flow rate expressions, the approach employed should be extensible to mixtures of carbon monoxide, hydrogen, and inert nitrogen, and to adi-abatic conditions, thus approaching the blast furnace process more closely. The fixed bed variables which are investigated in this study are particle diameter, flow rate, temperature, and bulk axial diffusion, as well as inter-and intra-particle mass transfer. Of particular interest is the effect of particle size upon fractional conversion for a bed operating under constant pressure drop. The constant pressure drop concept bears a close resemblance to the blast furnace process, where regions of larger particles may provide a greater permeability to divert most of the reducing gas flow from the regions of smaller ore particles. Under such conditions one would expect qualitatively that, for sufficiently small particle sizes where the flow rate is small and the total surface area is large, the reduction rate would be limited by the gas flow rate. Initially the gas entering the bed reacts very rapidly and the composition approaches the equilibrium conversion value a short distance from the reactor inlet. This concentration "wave-front" then moves up the bed as the flow of reducing gas is continued, leaving in its wake an ever increasing layer of reduced particles. Providing that the reducing gas leaves the bed at equilibrium concentrations, conversion is expected to increase with an increase in flow rate, and hence with an increase in particle diemater. Conversely, for sufficiently large particles the flow rate will be high but the surface area available for reaction will limit the reduction rate. Since the total surface area decreases with an increase in particle size, conversion, in this case, is expected to decrease as the particle diameter is increased. It is clear then that between these two extremes an optimum particle diameter must exist. THEORETICAL DEVELOPMENT Above the temperature where wiistite is stable (about 560°C) the reduction of hematite proceeds through the series Fe2O3/Fe3O4/FeO/Fe. On the basis of microstructural studies and earlier work, Edström1 has postulated a mechanism for the reduction of an ideal hematite lattice: 1) Iron phase formation at the boundary between wiistite, iron, and gas (for sufficiently porous iron). 2) Diffusion of iron across a wustite layer. 3) Phase boundary reaction of Fe3O4 to FeO. 4) Diffusion across a dense magnetite layer. 5) Phase-boundary reaction of Fe2O3 to Fe3O4. According to the mechanism postulated, gaseous reaction product has to be removed only at the boundaries between wüstite and iron or gas, the only possible exception being enveloped Fe3O4 specks. On this basis McKewan2,3 has proposed that one may consider the hematite reduction process as a simple two-phase system of oxide/metal. If, for FeO and Fe3O4 layers of negligible thickness, the hypothesis is made that the rate of formation of a

Jan 1, 1963

By S. A. Swensrud

REPORTS from smelters show that all were so occupied with the in- creased production called for during the first half of the year that little time was devoted to metallurgical developments. Improvements which have been made such as gas-firing and other alterations ill the reconstructed Hayden smelter, will require time for reporting. The labor situation at all plants held the most prominent place and put all other problems in the background. Coming events of considerable importance concerti the construction of two new smelters. The Chino unit of Nevada Consolidated which has long had its concentrate smelted at the El Paso plant of the American Smelting and Refining Co. is constructing its own smelter at the property in New Mexico. The newest Phelps Dodge development of the Clay ore body at Morenci, Ariz., will call for another new smelter.

Jan 1, 1938

By Albert F. J. Bordeaux

Discussion of the paper of Albert F. J. Bordeaux (Bi-Monthly Bulletin, No. 23, September, 190S, pp. 629 to 640). A. H. BROMLY, Zihuatanejo, Guerrero, Mexico (communication to the Secretary*) :-The following criticism of what "is offered as a summary which may be found useful by mining engineers," is not dictated by any captious spirit, but in the interest of historical and scientific accuracy. The States of Queretaro and Oaxaca have produced sufficient silver to warrant more extended notice. Referring to Pachuca, State of Hidalgo, the somewhat loose and. inexact statement is made that "the ore-deposit is an andesite, intermixed with quartz-veins, rich from the surface." A better description would be,-the ore-deposits consist of quartz-veins in andesite. It is notable that many of the rich shoots worked in recent days did not come to surface. In consequence, Pachuca, is often quoted by the ill-informed as a camp in which values improve with depth, the truth being that the veins carry shoots, or clavos, some of which were exposed at surface and some not. The name of " electric plow," applied to the mechanical stirrer of recent use, is certainly not to be recommended. The stirrer, or agitator, consists essentially of a traversing gang-plow, operated by power through shafting, drums, and wire-rope. The fact that in certain plants the motive-power used is electricity does not make it an electric plow. Such a name suggests a machine of which the motor is an essential and integral part; which is not so in this case. A lathe in a factory driven by water-power is not called a hydraulic lathe. My experience agrees with Dr. Raymond's note as to azulaque, which in sortie districts is also applied to blue copper carbonate. The El Oro, Esperanza, and Mexico mines should be allocated to the State of Mexico; the Dos Estrellas being in Michoacan, as stated. The El Oro quartz certainly does not appeal to me

May 1, 1909

By H. J. Tschirner, L. P. Davidson, R. K. Carpenter

HE electrolytic zinc plant of the American Zinc Co. of Illinois, at Monsanto, was expanded in 1943 to a capacity of 100 tons of slab zinc daily. This capacity was not attained because of inability of the leaching plant to deliver an adequate amount of solution for electrolysis. Changing the leaching method so that the acid was added to the roasted zinc material reversed the usual procedure and made it possible to attain the desired capacity. The conditions which prevented satisfactory work before this change and the difficulties which arose in reversing the usual leaching procedure are described. The "reverse" leach operation as now practiced is carried out as follows: All the calcine to be leached is fed continuously to a slurry mixing tank. About one third of the acid to be used is fed to the tank with the calcine. The slurry is discharged continuously to a Dorr duplex classifier in closed circuit with a Hardinge mill. The classifier overflow is pumped to any of six leaching tanks where the leach is completed. A finished leach is discharged through Allen-Sherman-Hoff pumps to Dorr thickeners, from which the overflow goes to the zinc dust purification and the underflow to vacuum filters. This change in leaching procedure from the usual one of adding calcine to a large amount of acid made it possible to provide an adequate amount of purified solution to the electrolyzing division and at the same time filter and dry all the residue produced. Operating savings in reagents and better metallurgical recoveries were also important benefits. The original flowsheet of the leaching plant provided leaching, sedimentation of the insoluble residue, and purification of the neutral zinc sulphate solution with zinc dust. The thickened residue was filtered and washed. The purification cake of excess zinc dust, precipitated copper and cadmium, and any insoluble residue was filtered off on plate-and-frame duplex classifier. Settlement in the thickeners was inadequate and the suspended solids in the thickener overflow gave rise to filtration difficulties after the zinc dust purification. Further, the filtration and washing of the leach residue was poor, and it became necessary to pump a large amount of unwashed or poorly washed residue to storage ponds outside the plant building. Two causes of the poor settling and filtration were determined: Soluble silica and ferrous iron in the calcine treated. The latter was a result of poor roasting and with more experience ceased to be a major problem. The silica was a normal constituent of the feed and the working out of the problem became a matter of controlling its solubility. The obvious method to render the silica insoluble was by intensive roasting. This, however, met with total failure as such roasting resulted in silicates, probably zinc, soluble in the 13 pct acid used for leaching. Attempts were made to coagulate the fine gelatinous slime with addition agents. Glue, lime, starch, beef-blood serum and others were tried without success. All the suggested tried-and-tested means of operating the thickeners gave no consistently good results. Variations in leaching time, in addition of calcine to the leaching tanks, "conditioning" of the pulp by prolonged agitation, immediate discharge of the leach upon completion to avoid breaking up flocs were all tried and given up as ineffective. Byron Marquis, of Singmaster and Breyer, worked with the plant staff on a beaker scale until a leaching procedure was developed which gave consistent results and a promise of overcoming the difficulties which had plagued the plant operation. It was suggested that the difference in solubility of silicates and zinc oxide in sulphuric acid could be made use of in a leaching method where the acidity was controlled carefully. Such control is possible when acid is added to a slurry of calcine. This process reverses the normal procedure of adding calcine to a vessel of acid, hence the term "reverse leach" was applied. In this way, the overall acid concentration can be kept very low. In the tests made, it did not exceed 0.05 g per liter free sulphuric acid. Numerous advantages were realized when no silicates were taken into solution and later precipitated as a bulky gel. The gel had made reasonable thickening and filtration of the leach pulp and practical drying of the residue impossible. When the gel was eliminated, thickening rates were increased as much as five times. The volume of residue after thickening represented about 10 pct of the total leach pulp and had been as high as 95 pct when the gel was present. The thickened pulp was filterable and the filtered cake was dried readily after washing. The zinc extraction from the calcine was slightly lower. This was more than compensated for by the increase in zinc recovered in solution from zinc which had been trapped in the gelatinous residue. The amount of copper recovered was lower. However, the amounts of other impurities, such as arsenic, antimony, and germanium, taken into solution were lower. This was particularly true of antimony. Since the inception of reverse leaching, no concentrates have failed to yield solutions free of antimony even when present in the calcine to the extent of 0.2 to 0.3 pct. Oxidation of ferrous iron is a problem of reverse leaching. Ferrous hydrate does not precipitate at pH 5.3 to 5.4 where a leach is finished. The usual oxida-

Jan 1, 1952

By J. Blodget Britton

To the question, " Do the Pennsylvania anthracites contain phosphorus?" asked at the last meeting of the Institute during the discussion on the metallurgical value of Western lignites, I can now give a definite answer. Through the kindness of a gentleman connected with the Philadelphia and Reading Railroad, and another connected with one of the principal ironworks on the Lehigh, there was sent to the Ironmasters' Laboratory a number of samples of the coals now largely shipped from the Schuylkill and Lehigh regions. Seventeen of these I examined for their contents of ash and phosphorus, and obtained results as follows : Ash. Phosphorus. No. 1, . 4.10 .0063 2, . . . . 7.97 .0209 113, . 5.53 .0049 114, . . . . . . . 6.55 .0056 . 5, . 5.39 .0761 . . . . . . . 11 6, 14.15 .0593 7, . 10 43 ,0049 rl 8, . . . . . . . 5.29 .0354 9, . . . . . . . 3.01 .0042 6L10, . . . . . . 3.03 .0042 1 1 . 275 .0014 12, . 2.82 ,0111 l'13, . .3.69 trace L1 14, . . .2.35 trace 15, . . . . . . . 7.22 .0014 16, . . . . . . . 3.49 .0167 17, . 4.63 trace

By R. L. Dietrich

Magnesium alloy sheet has less ability to accept bending at room temperature than most of the heavier metals. In work designed to improve the bend properties, the preferred orientation of the sheet is of major importance as it is in all studies of the properties of wrought magnesium products. When rolled into sheet, all of the common magnesium alloys form an orientation texture having the basal (002) planes approaching parallel to the surface of the sheet. This texture is only slightly affected by annealing. Magnesium single crystals are highly anisotropic, and, as might be expected, so are magnesium alloy wrought products in which a strong preferred orientation is developed. It is therefore not surprising that bend properties are affected by orientation. Ansel and Betterton1 reported that the orientation of AZ3lXt sheet varies from surface to center and that bend properties are improved by etching away the sharply oriented material at the surface of the sheet to reach the more broadly oriented structure below. This paper covers a study of that orientation, either during the rolling process or by treatment of the finished sheet, in an effort to improve the bend properties and toughness of sheet. Literature The orientation texture of magnesium and magnesium alloy sheet has been studied extensively. Early determinations2 showed that pure magnesium sheet has a preferred orientation in which the basal planes are parallel to the sheet surface within very narrow limits. J. C. hIcDonald3 and J. D. Hanawalt4 reported that sheet containing a small amount of calcium develops a "double" texture, that is, the majority of the basal planes are a few degrees from parallel to the surface and there is a noticeable vacancy at the parallel position. Bakarian5 made careful quantitative pole figures of both pure magnesium sheet and MI alloy SEPTEMBER 1949 sheet which show these features. In all of these studies, however, the orientation was determined by transmission methods in which the resulting pattern is an average through the thickness of the sheet. The tendency of wrought metal to exhibit a different orientation at the surface from that in the center has been reported by many investigators. G. von Vargha and G. Wasserman6 found that with copper, aluminum, iron, and brass the textures of rolled compared to drawn wires were the same at the center but differed markedly at the surface. It was also reported by investigators7 that the orientation of rolled aluminum varies from surface to center. Har-greaves8 found that the surface texture of AM503 (magnesium alloy similar to MI) sheet was different from the center texture. It is reported by Edmunds and Fuller9 that zinc alloy sheet sometimes had a thin layer at the surface with a strong orientation of the basal planes parallel to the surface, which, if present, impaired the bend properties of the sheet. Part1 Surface Orientation ofMag- nesium Alloy Sheet and the Effect on Properties Attempts to correlate the bend properties of magnesium alloy sheet with tension ductility over short gauge lengths proved unsuccessful and the subsequent investigation showed that nonuniformity in orientation is a con- tributing factor as the properties of the surface material have a much more important effect in bending than in tension. A program to study the relationship between surface orientation at the surface and bend properties was then undertaken. First, the effect of etching away the surface of sheet on the bend properties and the orientations at the various depths were studied. Sheet samples of M1, AZ31X, and AZ61X were etched in dilute nitric acid to remove the surface material for various depths to 0.015 in. As may be seen in Table 1, the minimum bend radius improved considerably as the surface layers were etched away but it was necessary to etch the sheet quite deeply, much more so than was found necessary by Edmunds and Fuller9 on zinc sheet. It is also apparent that the amount of etching required is a function of the sheet thickness. In all of this work, radii were measured as R/t, the radius divided by the sheet thickness, in order to eliminate the effect of the reduction in sheet thickness produced by the etching. To determine the orientation texture of the sheet, X ray reflection patterns were taken using copper radiation with the bearn striking the specimen at an angle of 17' to the surface, which is the Bragg angle for the (002) planes of magnesium. Two exposures were made of each specimen, one with the beam perpendicular to the rolling direction and the other with the beam parallel to the rolling direction. The symmetry of the preferred orientation in magnesium sheet is such that these two photographs gave an approximation of the pole figure sufficiently accurate for qualitative work and it was not thought worthwhile to make complete pole figures. These X ray patterns show that the orientation has a much narrower spread at the original surface of the sheet than below the surface. The narrow spread is found in sheet having the majority of the basal planes (002) parallel to the surface, and since this is an unfavorable position for slip, it is

Jan 1, 1950

By H. Margolin, E. Ence

Two versions of the Ti-Mn binary diagram have been published recently.' , -0th diagrams show two compounds in the region between 40 and 70 wt pct Mn, but disagree as to the reaction in which these compounds are involved. The investigation of the manganese-rich portion of the Ti-Mn binary diagram was undertaken at New York University as part of an investigation of ternary systems with titanium and manganese in order to determine which of the proposed diagrams is correct. A number of alloys between 31 and 70 pct Mn were prepared in a manner similar to that described by Cadoff and Nielsen; except that low currents (110 amp in argon atmosphere) and long melting times (up to 20 min) were used to prepare the alloys. Compositions were determined from weight-loss data, assuming all loss as due to manganese. Heat treatments were carried out with relatively large pieces, since there was a tendency for manganese to be lost during heat treatment. When X-ray diffraction data was to be obtained, the central parts of heat-treated specimens were used to make filings or powders which were not heat treated. Specimens were heat treated from the as-cast state. Heat-treatment times were as follows: 1150°C, 1 day; ll00°C, 2 days; 1000°C, 5 days; and 900°C, 15 days. It should be noted that equilibrium was not attained at 900°, 1000°, and in one case, at 1150°C. Metallographic specimens were electrolytically polished and strain etched by a technique described elsewhere.' At least four, and possibly six, phases were found in the region investigated. On the basis of information available at this time, a completely self-consistent diagram cannot be constructed, and therefore data are presented only for those phases which have been identified by both X-ray and microstruc-ture. Of the compounds detected, the one highest in manganese is the Laves phase, TiMn,, which is hexagonal with a MgZn, type of structure.V he diffraction data for TiMn2 from a 70 pct Mn alloy annealed at 1150°C are shown in Table I. The c/a ratio and parameters of TiMn2 agree well with those of Wall-baum hnd Rostoker et al. The values obtained here are c/a = 1.641, a = 4.825A. Another compound is the y-phase which is estimated to contain about 60 pct Mn. The y-phase has a structure which is identical to that of TiMn, with c/a = 1.639, a = 4.906Å. The fact that y has a Laves-type lattice would suggest that TiMn, has a range of solubility which extends from the composition of TiMn2 (69.6 Mn) to that of y (60 pct Mn). However, this could not account for microstructures which, in the 60 to 70 pct Mn region, show several phases in both the as-cast state and after annealing at 1150°C. Fig. 1 shows a two-phase structure of a 60 pct Mn alloy annealed at 1150°C. The phases present are y (white) and e (dark). If y were TiMn, then, according to Rostoker et al.,' the second phase of Fig. 1 should be P-Ti. The diffraction data for the 60 pct Mn alloy of Fig. 1 are shown in Table I. The starred d-values are from the e-phase and these lines do not correspond to those of &Ti. Comparison of as-cast and 1150°C microstructures of the 60 pct Mn alloy indicates that e precipitated from y. Since y has a

Jan 1, 1955