Search Documents

By Marcelo Macedo Fialho

No processo produtivo de aço, as empresas buscam continuamente a redução do custo de produção. Isto pode ocorrer através de diversas formas, tendo como as principais, o ganho de rendimento, o aumento de produtividade, a redução do homem hora aplicado e a redução do custo de matéria prima. Objetivando reduzir o custo de produção integrado placa bobina, a ArcelorMittal Tubarão busca aumentar o percentual de placas enviadas diretamente do Lingotamento Contínuo de Placas para o Laminador de Tiras a Quente. Os ganhos se dão, em primeiro plano, através da redução da intervenção nas placas aumentando o rendimento de placa e exigindo menos mão de obra para o corte e escarfagem de placa e, em segundo plano, através do aumento da temperatura média de enfornamento, propiciando maior produtividade no laminador de tiras a quente e menor consumo de energia para realizar o pré-aquecimento da placa antes do processo de laminação. Somado a isto, a maior disponibilidade de placas no pátio do LTQ, aumenta a chance de laminação exigindo menos paradas do LTQ e aumentando a produção. Os ganhos estimados com o projeto, apenas no que diz respeito a redução de custo de condicionamento são de 6MUSD/ano.

Jul 30, 2018

By Marcelo Eduardo Rocha Gesualdi

A solução de eletrocentros aplicada a subestações elétricas dentro de uma planta industrial vem se consolidando no processo de mineração no Brasil em virtude de suas diversas vantagens de modularização, montagem e testes em fábrica, acelerando a instalação e energização das subestações em campo aonde os prazos de disponibilidade são sempre curtos para o início da operação da planta. Adicionalmente ao conceito de eletrocentros, a automação de subestações elétricas tem possibilitado através da utilização de redes de comunicação baseadas na norma IEC 61850 uma nova visão de integração dos diversos equipamentos, painéis elétricos e de automação que compõem as subestações dentro de uma plataforma integrada com a automação de processos da planta, disponibilizando um maior número de informações para o correto controle da subestação e gerenciamento de energia, bem como a redução significativa do cabeamento interno de controle e comando entre painéis facilitando ainda mais a modularização dos eletrocentros. Além das vantagens de montagem e comissionamento, o conjunto eletrocentro e sistema integrado de automação possibilita para a operação e a manutenção da planta consideráveis avanços através do gerenciamento remoto e integrado de informações, garantindo uma maior eficiência em seus respectivos processos.

Aug 16, 2017

By Wilker Fernando Matias Lemos

Diferentes equipamentos e processos de produção industrializados utilizam, em maior ou menor grau algum nível de automação e controle, aos quais é possível avaliar através de alguns inputs selecionados (sensores específicos, sequências de operação, temporizadores, memórias, etc.) se o equipamento ou processo encontra-se de fato em plena execução de seu trabalho ou função principal. O objetivo do projeto é "descobrir" o momento em que os equipamentos / processos não estão em operação plena e "automaticamente" modificar o estado de funcionamento de seus órgãos principais e/ou auxiliares como: motores e bombas, qualquer mecanismo de atuação direta, (por meio de redução de velocidade, carga e/ou desligamento controlado e outros) que não precisariam necessariamente estar a pleno funcionamento. O projeto visa à aplicação do funcionamento em modo "stand by" normalmente utilizado em equipamentos eletroeletrônicos a maquinas e processos industriais, possibilitando economia de energia e permitindo que voltem imediatamente à sua condição plena de funcionamento quando maior ritmo operacional for solicitado. O trabalho mostra em aplicações práticas a possibilidade de incluir a filosofia nos sistemas automatizados em diferentes setores da indústria, logo podendo trazer grandes benefícios através de ações estratégicas com baixo custo de implementação.

Jul 31, 2018

By Douglas Glenn Stalheim

Production of structural steel with a minimum yield strength of 700 Mpa produced as hot rolled coil has become increasingly popular due to cost considerations when compared to quench and temper equivalent product. This grade when produced as hot rolled coil requires the use of microalloy precipitation strengthening mechanisms. This is typically a combination of niobium and titanium microalloys. While the metallurgical concept of structural steel precipitation strengthening mechanisms has been well researched and published, actual implementation into the production process can be very challenging. In addition to achieving a minimum yield strength of 700 Mpa, in many applications additional mechanical property attributes of formability as measured by hole expansion testing along with low temperature toughness properties are now required. Achieving a balance of all the mechanical properties in a stable and repeatable performance in production using microalloy precipitation strengthening mechanisms further increases the challenges. This paper will discuss the metallurgical/process strategies required to successfully produce 700 Mpa minimum yield strength hot rolled structural steel coil. In addition, the role and goals of both niobium and titanium in this product design will be presented.

Oct 30, 2017

By Daniel Mapa Clemente

Processing of tin slags in reduction furnaces was studied in order to optimize tin recovery and reduce recirculation rates of slags containing thorium and uranium oxides. A theoretical approach considering a mass balance of the process was developed and adjusted by experimental results in order to predict the final slag composition. A metallic phase (FeSnSi) was discovered trapped in the slag due to high apparent viscosity, raising the FeO and SnO2 contents of the slag sample. This FeSnSi alloy is rich in tin and its recovery would help to reduce the slags recirculation. High contents of ZrO2 were found in the slag, restricting it from reaching complete fluid phase. Through an analysis of the slag in the CaO-FeOx-SiO2 and ZrO2-CaO-SiO2 phase systems it can be concluded that final slags should be modeled aiming fluid phase at working conditions and additions should be planned in order to control ZrO2 levels.

Oct 30, 2017

By Luis Acainas Caballero, Karl Hoen, Stephan Krämer, Christoph Klein

The situation of the steel industry is still challenging. Worldwide overcapacities have an impact on profitability. More than ever, the point at SMS group is to provide the steel industry with flexible and profitable technologies and systems over the whole process chain. One example for that is the thin slab casting and rolling technology and, in particular the CSP® technology (Compact Strip Production), being well established for hot coil production. From its introduction in 1989, CSP® technology has been continuously further developed. Today, on a CSP® plant, the full range of high-quality steel grades can be produced with tightest geometrical and metallurgical tolerances under optimal economic conditions. With the introduction of semi-endless rolling and, as a further step, the endless rolling process, the product range for thin and ultra-thin products has been further enlarged, allowing for the production of hot rolled coils with a thickness of 0.8 mm for low carbon steel grades. Also high-strength steel grades may be produced with gauges below the minimum product thickness that can be achieved in a conventional-type hot rolling mill. Another step in the further development of CSP® technology is digitalization. In December 2016, the CSP® plant of Big River Steel (BRS), located in Arkansas, USA was put into operation. It is the first learning steel mill in the world. The CSP® plant of BRS comes with innovative technologies, providing impressive operational results right from the beginning.

Oct 1, 2019

By Jose Maria Rodriguez-Ibabe, Ronaldo Antonio Neves Marques Barbosa, Douglas Glenn Stalheim

Major costs in the production of both flat and long commodity grade structural steel products include alloy, labor and energy. Flat and long commodity grade structural steels such as ASTM A36, ASTM A527Gr50, S235, S275, S355 and other equivalent world societal standards represent over 500 million annual tons worldwide. These simple commodity grades consist of a minimum of three base common alloying elements, carbon, manganese, silicon and then can be supplemented with microalloying elements of either vanadium or niobium. Since 2016 raw material costs for two of the five alloying elements in these commodity grade structural steels, FeMn and FeV, have risen significantly and/or have become volatile making it difficult to maintain stability in profitability for these commodity grades. For steel plants producing hundreds of thousands and in some cases over a million tons annually of these common structural steel grades because of the significant alloy cost increase for Mn and V alloy additions has squeezed profitability of these grades. These grades typically represent the base loading for cost controls in most all steel plants and hence a significant cost increase or volatility in two of the five elements used for these grades having a negative effect on overall production costs. However, with a proper strategy for alloy designs working in conjunction with the mills existing processing capabilities to achieve the desired end metallurgy/mechanical properties, alloy costs and operational efficiencies can be realized.

Oct 1, 2019

By Yong Tian, Tian Zhang, Zhao-Dong Wang

To meet the requirements of high-performance steel plates, while reducing manufacturing costs and saving energy, the advanced cooling system for plate mill (ADCOS-PM) with functions of accelerated cooling (ACC), ultra-fast cooling (UFC), and direct quenching (DQ) was researched and developed by the State Key Laboratory of Rolling and Automation (RAL). Since 2003, several sets of ADCOS-PM device were developed and implemented in industrial practice. To fully utilize the ADCOS-PM technology, the combination of various strengthening mechanisms was promoted by NG-TMCP technology and low-cost, high performance plates were produced such as pipeline steels, and high-strength construction machinery steel.

Oct 1, 2019

By Christoph Sedivy

Industrie 4.0 is slowly but surely arriving in the melt shops. Furnaces are being equipped with more and more sensors, digital models are increasing the degree of automation, and information is being shared between different aggregates within the plant. Because the electrode control system plays a key role in electric steelmaking, it naturally assumes an important position in the melt shop’s Industrie 4.0 strategy. In addition to reliable, state-of-the-art core regulation functionality, monitoring and reporting tools and the ability to communicate with other equipment are also required. Therefore, the latest generation of our electrode control system, the Melt Expert, was developed based on Industrie 4.0 design principles. Intelligent plant condition diagnostics, performance monitoring, and user-defined reporting are essential modules in this new system. With these functionalities, electrode control systems are developing into the information and control center of the furnace. A newly developed software app brings most relevant process information to mobile devices. This feature allows steelmakers to keep an eye on the performance of their equipment anytime and anywhere. This paper describes the new features of the electrode control system and shares our customers’ operational experience. Our focus is on the practical aspects of plant status monitoring, KPI reporting, and diagnostic functionality as well as the improvements achieved.

Oct 30, 2017

By Claudio Pereira Diogo

A lot of galvalume/aluzinc steel sheet was furnished to a metallic roof manufacturer intended for tile fabrication. But, according with the roof manufacturer, that coils develops a different superficial aspect during processing. The purpose of this work was to provide an explanation for the appearance of the observed surface on one side of the coils. In order to find out the origin of the problem, mechanical and microstructural characterization tests were done at INSPEBRAS with the support of a partner laboratory. The results are described in this paper with their analysis and conclusions.

Aug 16, 2017

By Eduardo Dominguez Trindade

Lubricant oils are subjected to reciprocating movement in the piston ring/cylinder tribocouple of automotive engines. In this kind of movement, the relative speed oscillates between zero and a maximum, and therefore the lubrication regime goes from boundary to hydrodynamic. Tribotests are widely used in laboratories to hint at the friction developed in these systems. In the present work, a SRV tribometer was used to evaluate the friction behaviour of lubricant oils under reciprocating movement up to 60 Hz. A high acquisition rate allowed the analysis of data inside each reciprocating cycle. Both a pure base oil and a fully formulated lubricant were used. Changes in the contact pressure, viscosity and speed were seen to influence friction, which was correlated to the relative thickness predicted by Hamrock-Dowson equation. While some observed characteristics were typical consequences of the Stribeck curve, other effects were also observed, such as the occurrence of seizure at high reciprocating frequency. A lower boundary coefficient of friction due to additive package in the formulated oil was also observed. The results allow a better understanding of friction in reciprocating cycles and can be used to evaluate the performance of oils and surfaces in laboratory prior to engine testing.

Jul 31, 2018

By Helênio Resende Silva Júnior

Arcelor Mittal Asturias coking plant at Gijon works, Spain, is undergoing a complete modernization of the whole coke making complex. In this context, Gijon has to be considered a brownfield project, where Paul Wurth has been awarded with the engineering, supply of key equipment as well as erection and commissioning supervision services for the rebuild of two coke oven batteries the modernization of the adjacent by-product and relevant waste water treatment plants. Main objective of this paper is to present the technological improvements introduced by Paul Wurth in the rebuild of a modern plant focusing on fulfilling all the recent environmental regulations.

Oct 30, 2017

By Karl Berger

Today we are talking about Industry 4.0, as the latest revolution of industrial processes and progress, considering that the steam engine (Industry 1.0), railways and cars, mass production in the 1920th (2.0), Industrial Automation (3.0), and finally integrated manufacturing, integrated communication, and internet (4.0) can be seen as the state-of-the-art situation in industry, nowadays. Similar to the Industry progress, we can approach the rolling process of material, which started about 150 years ago in a very basic way. Steam engine- and belt driven-mills were very operators’ intensive, brutal and risky to operate. Mechanical improvements brought throughput, safety and quantity, as also quality of the products. The rolling of steel, in particular of rails, beams, rebar, strip (focus in this paper) and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. From single stands to continuous rolling trains the production and quality of mills increased significantly. From ingots and blooms to slabs, we have to admit a big jump in which has changed the face of the world significantly. Thin Slab Rolling has revolutionized the output and the throughput of rolling mills (Generation 3.0 to 5.0). Finally, Endless Rolling, has boosted the quality and quantity of rolling mill processes and permitted nowadays to enter in market niches which were not thinkable a decade ago. Mastering the automation and applying reliable systems (mechanical and electronically) of drives, actuators and sensors, as also communication and information interchange to all levels of automation are the success factors of such complex mills, we call herein after “Rolling Mills of Generation 6.0”.

Aug 16, 2017

By Jari Larkiola, Aarne Pohjonen, Juha Jokisaari, Oskari Seppälä, Joonas Ilmola

Finite element method (FEM) is widely used to model the hot strip rolling process. Flatness defects e.g. front-end bending in multipass hot strip rolling is studied by authors using a finite element (FE) model with interactively operating automated controlling logic (ACL) [1]. However, industrial corresponding grade of accuracy in strip thickness subsequent to the rolling pass is not easily accessible in FE-model without separate calculation of significant rolling parameters and integrated roll gap control. In order to study flatness defects and optimize pass schedules the controlling and physics of the FE-model must correspond to the industrial process. For this need the automated controlling logic is upgraded by setup calculations to predicting roll force and work roll flattening. These predictions are utilized in setup positioning of a work rolls. Reliable setup calculation enables smooth multi stand rolling process without significant additional adjustment of roll gap clearance. State of art rolling technology requires above-mentioned setup controlling for the FE simulations to simulate different pass schedules without time consuming preparations. Operational setup calculations together with automated controlling logic of hot strip rolling enable simulation of new pass schedules and efficient problem solving.

Oct 1, 2019

By Gabriel R. Royo

This paper will cover a back up roll bearing technological upgrade, being implemented at the TERNIUM SIDERAR Hot Strip Mill (HSM), in San Nicolas, Buenos Aires, Argentina. This change was motivated by increased operating loads, which caused the original bearings to be outside the designed bearing rating. The problems were first identified by bearing seizures in some stands, and later followed by cracks forming in the back up roll neck areas due to fatigue and overload. MORGOIL engineers worked together with TERNIUM SIDERAR engineers in analysing the problem and to upgrade the mill with the newest and most economical technology. The upgrade consisted of changing the bearings to the latest generation MORGOIL bearing: the KLX, which within the same space, increases bearing capacity around 25%. This was accomplished re-utilizing all chocks. The new bearing allowed for a re-design of the geometry of the back up roll neck, making it much stiffer than the original design, and eliminating fatigue failures. In addition, an upgrade to hydraulic mounting and dismounting using the MORGOIL® HB lock was also implemented, as well as changing to the newest MORGOIL® HD seals. With the MORGOIL® KLX® upgrade, TERNIUM SIDERAR HSM increased load capacity, allowing them to roll products that were not even considered decades ago. Both older oil film bearings and roller bearing mills have been successfully upgraded while reusing existing chocks and in many cases rolls. Solutions are customized to the customer’s equipment and goals.

Oct 30, 2017

By Satish V. Kailas

For product sustainability “closing the cycle” is the first requirement. If the materials used in making the product is not replenished at the rate at which it is being extracted, the cycle is open and the product would not be sustainable. This includes the materials used in generating the energy used to make the product, the transportation, use and disposal. If the materials used in a product, that includes lubricants, is one that cannot be replenished, it has to be recycled for the product to be sustainable. The other basic condition for sustainability is the eco-friendliness of the product. It is argued that the present lubricants do not fall in this category. Using the example of cutting oil emulsions we have shown that it is possible to meet the conditions of sustainability in terms of both the material extraction-replenishment cycle and eco-toxicity. Cutting oil emulsions made from coconut oil and natural additives are shown to have superior cutting properties and are completely eco-friendly. It is concluded that products made using these conditions are possible and is a necessity for man to lead a sustainable life. Closing the cycle, with respect to the energy used in the cycle will make the product completely eco-friendly.

Jul 31, 2018

By Eduardo Vitral

The present study focuses in the simulation of pattern formation by ion beam sputtering on a material surface. This process is responsible for the appearance of unexpectedly organized patterns, such as ripples, nanodots and hexagonal arrays of nanoholes. A numerical analysis of preexisting patterns is proposed to investigate surface dynamics, based on a model derived from a Kuramoto-Sivashinsky anisotropic equation, in a two dimensional surface with periodic boundary conditions. While deterministic, its highly nonlinear character gives a rich range of results, making it possible to describe accurately different patterns. A finite-difference semi-implicit splitting scheme is employed on the discretization of the governing equation. Simulations were conducted with realistic coefficients related to physical parameters (anisotropies, beam orientation, diffusion). The study dealt with a random and a monomode 1D structure initial condition in order to understand how the shape and wavelength of the initial pattern evolve with time. Ripples and hexagonal patterns were observed in the results, being physically consistent with the phenomenon. Moreover, the Method of Manufactured Solution has been used as verification of the developed numerical scheme.

Aug 16, 2017

By Tatiane Suelen Santos Silveira, Dagoberto Santos Brandão, Dalila Chaves Sicupira, Graziele Gianini Braga Maria, Marcos Vinícius Fonseca Ferreira, Daniela Barçante Perasoli

O aço inoxidável duplex combina as propriedades mecânicas da ferrita e a resistência à corrosão da austenita, sendo muito utilizado em aplicações industriais que requerem um bom desempenho. Quando submetido a deformações intensas, a austenita transforma-se parcialmente em martensita, aumentando a resistência do aço. Quando o aço é recozido, essa transformação é revertida e a martensita se transforma em austenita, ocasionando um refino de grão do material. Fases secundárias formadas durante o recozimento podem prejudicar suas propriedades mecânicas e corrosivas. Nesse sentido, o objetivo desse trabalho foi avaliar o efeito da temperatura de recozimento na resistência à corrosão do aço inoxidável duplex UNS S32304 laminado a frio. O aço foi submetido à laminação a frio, com deformação de 60%, e posteriormente recozido nas temperaturas de 600°C, 700°C, 800°C e 900°C por um tempo de 0,5 h. A resistência à corrosão foi estudada através da técnica de polarização potenciodinâmica. A laminação a frio promoveu a formação de martensita induzida por deformação (SIM) e a reversão parcial começou a ser observada após recozimento a 600ºC. A ocorrência de SIM promoveu significativa diminuição do potencial de pite e o aumento da temperatura de recozimento aumentou a resistência à corrosão localizada.

Mar 1, 2019

By Carlos Gonzalo Alvarez Rosario

O presente trabalho avaliou a capacidade de degradação bacteriana de cianeto da cepa Bacillus pumilus em efluentes contaminados. Para isso foram realizados estudos de degradação bacteriana de cianeto em frascos agitados e incubados em agitador orbital durante 120 horas. Os ensaios aconteceram em três etapas; a primeira etapa consistiu na ativação e crescimento da bactéria em meio Luria Bertani, seguida da adaptação a ambientes alcalinos e por ultimo a etapa de degradação de cianeto. A proporção de inoculo foi de 1:500. Utilizou-se tampão CAPS para manter o pH alcalino. Para avaliação da degradação de cianeto foi preparada uma solução sintética contendo 500mgL-1 de cianeto de potássio pH 10. Foi avaliada a influencia da temperatura na degradação bacteriana (27, 32 e 37oC). O controle do crescimento celular foi realizado por medidas de densidade óptica com comprimento de onda ?=600nm. A quantificação do cianeto livre foi realziada por polarografia utilizando-se o analisador voltamétrico (computrace control 797 Metrohm). Dos resultados obtidos foi possível determinar que a cepa B. pumilus obteve melhor desempenho na degradação de cianeto a temperatura de 27oC conseguindo degradar 100% do cianeto livre presente na solução. O tempo empregado para a degradação total do cianeto foi de 3 dias.

Oct 30, 2017

By Alexandre de Aparecida Morais

No processo de lingotamento contínuo a secagem e o pré-aquecimento do refratário do distribuidor são de fundamental importância. Estes são realizados visando: reduzir a perda de calor do aço líquido, reduzir as bolhas nas primeiras placas, evitar respingos de aço (reações) ocasionados pela umidade e prevenir a degradação refratário por choque térmico. Para aços planos, os sistemas para promover a secagem e pré-aquecimento podem ser do tipo a "quente" (mais usual) ou a "frio". É denominado "partida a quente" quando se realiza a secagem e o pré-aquecimento; e de “partida a frio”, quando apenas a secagem é realizada. Têm-se como características distintas entre os processos: - A Quente: maior consumo de gás; forte degradação do refratário; temperatura de trabalho do distribuidor mais elevada, deteriorando as condições do ambiente; - A Frio: menor consumo de gás; redução da degradação do refratário; no entanto, exige um controle rigoroso da curva de secagem, o que implica maior investimento inicial no equipamento de secagem. Em 2002, após uma análise de viabilidades a ArcelorMittal Tubarão implementou o sistema de frio. Este artigo mostra a evolução deste sistema após a sua implementação, analisando a correlação com defeitos, a implementação de melhorias e os ganhos obtidos.

Jul 30, 2018