Search Documents

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

Law of the Sea. - The Ninth Session of the Law of the Sea Conference resumed July 28 at Geneva and will run for 5 weeks. The 160-nation Conference began in 1973. Two of the major factors to be discussed are the transfer of technology to the UN-controlled Enterprise or mining authority, and how the 36-member Council will make decisions. As the session completed its third week, delegates expressed little hope of completing a treaty text this year. There was a feeling, though, that substantive issues might be settled so that a treaty text can be completed next year. The Deep Seabed Hard Mineral Resources Act signed by the President on June 28, provides an interim regulatory procedure for ocean mining activities conducted by U.S. nationals that may be superseded by a law of the sea treaty.

Jan 1, 1980

By H. W. Busch

In the course of examinations by representatives of the Bureau of Mines of several compressed-air systems in which explosions had occurred, samples were obtained of the carbon deposits that are formed normally in various parts of the systems by decomposition of the compressor lubricating oil. Experimentation with these carbon deposits has demonstrated that they contain a "carbon-oxygen complex" similar to that formed on coal and on other carbonaceous materials and generally recognized as being the cause of spontaneous heating of coal. The exothermic properties exhibited by such a complex are considered significant in relation to the possible initiation of combustion reactions that may lead to explosions or formation of carbon monoxide in compressed-air systems. This report discusses the occurrence of explosions and formation of carbon monoxide in the use of compressed air and presents results of experimentation conducted with carbon deposits from air compressors.

Jan 1, 1949

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By D. S. Kieffer

Ground characterized by hard boulders embedded in soft matrix represents one of the most challenging conditions for TBMs, as the cutterhead must cope with the non-optimal conditions of cutting hard blocks while simultaneously excavating through soft, soil-like matrix material. Dowden and Robinson (2001) and Hunt and Mazhar (2004) summarize several case histories relating to the problems of advancing a TBM through boulder-laden ground and provide guidance with respect to appropriate site investigations and baselining strategies. Some rock types constituting boulder-laden ground include: ?Sedimentary Rocks?cemented alluvial channel deposits, colluvium/talus, landslide debris, and glacial till. ?Igneous Rocks?agglomerates, lahars, and pyroclastic deposits. ?Metamorphic Rocks?tectonic mélange and cataclastic fault zones. ?Decomposed Rocks?corestone bearing saprolites. Disc cutters are commonly utilized to cut the hardblocks; however, as compared to the understanding of disc cutter behavior in hard continuous rocks, little is known regarding fundamental cutting mechanisms in highly heterogeneous bouldery ground conditions. To advance this understanding, a suite of full scale tests have been performed using a linear cutting machine at the Colorado School of Mines (CSM). This paper summarizes the observed cutting mechanisms and their practical implications for TBM excavations through boulder-laden ground.

Jan 1, 2008

By William F. Keyes

Greensand, which is widely distributed in the Eastern United States, was produced in 1975 only by Inversand Co., a subsidiary of Hungerford & Terry, Inc., near Clayton, N.J. Production and sales information are not available for publication. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was used by manufacturers as filter media in equipment for the removal of manganese, iron and other elements from water. The University of Delaware received a grant of $17,051 from the Bureau of Mines early in 1976 to continue its studies of the effectiveness of greensand in removing metallic contaminants from waste waters.

Jan 1, 1977

By Frank Chase, M. Terry Hoch, George Karabin, Joseph C. Zelanko, Christopher Mark

Pillar recovery continues to be a significant ground control hazard. During the past decade, 10 miners were killed during pillar extraction operations in southern West Virginia. Studies conducted during the past decade have identified a number of “risk factors” that can be used to evaluate pillar extraction plans: •Cut sequence •Final stump •Timber or Mobile Roof Supports •Roof bolting •Intersection span •Depth of cover •Roof quality •Age of workings For each of these factors, rock mechanics science suggests which alternative would be expected to be more risky. For example, numerical models were used to evaluate different cut sequences, and indicated that less roof convergence occurred with the outside lift method than with the Christmas tree in the particular environment simulated. For many of the risk factors, accident statistics confirm the science. One finding was that currently almost 70% of the retreat coal in southern WV is being mined with MRS. In contrast, timber supports were used in 70% of the past decade’s pillaring fatalities. This paper discusses each of the risk factors in turn, presents the relevant accident statistics, and shows how the risk factors can be combined to estimate the overall hazard. It also addresses the use of pillar design to minimize the risk of global stability hazards including squeezes, massive collapses, and bumps.

Fragmentation Characteristics of Iron Ores from Anshan, China

Sep 13, 2010

By J. N. Van der Merwe

The current state of the South African mining industry is briefly reviewed from the point of view of an engineer not schooled in the finer details of predictive economics. Based on the assumption that current world exploration targets are indicative of which commodities the world will want in the future, it is concluded that the South African mining industry will continue to be viable and growing well into the future. South Africa holds the minerals the world wants and needs, and as long as the world has people, the demand for those, including gold, will continue to grow. There still is a growing demand for vanity commodities' and even the demand for platinum as a jewellery material displays significant growth. Mine safety still needs to improve, but significant improvement has already been made although the industry is not always acknowledged for the effort in this field. The safety target set for 2013 is within reach but will require sustained effort. The physical mining conditions for the main revenue earners, coal, platinum, and gold, will change substantially in the near future. Research in mining has declined alarmingly and it is urgently necessary for that to be revitalized to generate the knowledge that will be required. In order to streamline the transfer of knowledge to the mining engineers of the future, research needs to be conducted with the full involvement of the universities. It will also be necessary for the universities to continually review curricula to incorporate the latest knowledge and to embark on a campaign of knowledge transfer to the older generation of mining engineers. The mining industry is well supported by the universities, who have done their duty with regard to societal transformation, and the universities are in turn supported by the industry through vehicles like the METE Industry is also strongly supported by a number of professional and vocational societies. The SAIMM will continue to play its vital role as the meeting point of the mining technical sciences, and will continue to disseminate knowledge via the journal, schools, and conferences. In the future, it will review its modus operandi to support the needs of growing membership in the remote branches. It will enter the research arena in an appropriate manner and give effect to the developing integration of mining and society. The most important threat to the future of the mining industry is the recurrent mention of nationalization. While interaction between the mining industry and political and economic development of South Africa has always been characteristic, the current debate is emotional more than rational, and engineers are not well equipped to participate. This matter needs to be finalized before it becomes a popular force that politicians cannot control.

Jan 1, 2011

By José De Piérola

En los procesos de flotación y lixiviación de la producción de cobre se utilizan aguas recicladas y agua fresca. Este último es un insumo indispensable para ambos procesos, ya que constituye un elemento determinante del volumen de producción, así como un medio de vinculación obligado con el entorno social de las operaciones. En ese sentido, el presente texto describe la utilización del agua- en tanto representa un componente de rentabilidad relacionada al costo, al equilibrio del aprovechamiento con el comportamiento de la fuente y a la sostenibilidad con el entorno social, lo cual implica compartir el agua y recursos económicos para una planificación y adecuada priorización en su asignación.

Sep 9, 2007

By W. G. Davenport, M. Paneni

Experiments in sheets of mercury and water have confirmed that the dynamics of bubble rise are simi-lur in Liquid metal and aqueous systems. RECOGNITION that bubble/metal interactions are important in pyrometallurgical refining processes (e.g., steelmaking, vacuum degassing, deoxidation of copper) has led to a number of investigations into the dynamic behavior of bubbles rising in liquid metals. Terminal velocities of bubbles rising in mercury (20°C)' and silver (1000" to 1050"c)1,2 have been measured. Good agreement between aqueous and liquid metal systems has been obtained. Shapes of air bubbles rising in mercury have been determined experimentally by Davenport, Bradshaw, and Richardsonl who used a system of electric probes to measure maximum horizontal and vertical dimensions, Fig. 5. In the present work the motion and shape of nitrogen bubbles rising in a thin sheet of mercury (i.e., a "two-dimensional" environment) have been studied with the view of confirming dynamic similarity between aqueous and metallic systems. The use of thin sheets of liquid permitted direct visual and photographic comparisons of bubble behavior in clear liquids and in mercury. EXPERIMENTAL METHOD The thin sheets of mercury or water were held in a clear acrylic plastic container, Fig. 1. The sheets of liquid were 80 cm high by 30 cm wide and 0.47 cm thick. Single bubbles were formed by injecting the desired volume of nitrogen into an inverted semicircular cup (stainless steel). The cup was then rotated into the upright position using an external handle thus releasing a single bubble of measured volume. Nitrogen was injected into the cup from a nitrogen cylinder through the external handle and a hollow rotating axle. The volume of a bubble (volume range 0.01 to 10 cu cm) at any instant was obtained by connecting a soap film meter to a small gas space above the liquid. By this technique any change in the volume of a gas bubble in the liquid (i.e., during cup filling or during rise) produces an equivalent displacement from gas space A into the buret B. This displacement is determined by measuring the movement of a horizontal soap film in the buret. Bubble shapes were determined using single-frame photography. Rising velocities were determined by cinephotography with a 1/100-sec stopwatch in the field of view. In both cases dimensions were referenced to a rule attached to the container surface, also in the field of view. Linear dimensions were measured on projections of the single-frame negatives. Rising velocities were calculated from measured heights of rise (10 to 20 cm) and times of rise. The effects of disturbances caused by cup rotation and by bubble release were minimized by photographing bubbles at a point not less than 25 cm above the cup. MATERIALS Mercury: Technical-grade purified: minimum 99 pct Hg; Johnson Matthey and Mallory Limited, Toronto. Nitrogen: Technical-grade purified nitrogen: 99.99 pct Nz, 0.01 pct 02, trace argon; Air Liquide Canada Limitee, Montreal.

Jan 1, 1970

By R. R. Sayers

The increasing use of hydrogen fluoride (annual consumption now exceeds 500,000 pounds (1)4/) directly and its occurrence as a byproduct of the utilization of fluorine compounds in the mineral industries, especially in metallurgical processes and in the refining of petroleum products, has aroused interest in its toxicity, and a brief review of the literature, with special reference to the hazard of poisoning in the mineral industries, seems to be opportune. Recently, residents in the vicinity of aluminum plants have been complaining of injury to livestock and vegetation as well as to their own health from the gases discharged into the air during operation of the plants, hydrofluoric acid gas apparently being the offender. The comparatively recent utilization of hydrofluoric acid in the alkylation process for the production of high-octane gasoline has raised the question of the hazard of poisoning in the petroleum Industry. In addition, the use of fluorine-containing refrigerants has extended the potential al exposure outside of industry (2).

Jan 1, 1945

By J. W. Wilson, P. C. Graham

SUMMARY The Witwatersrand quartzites in which South African gold mining operations are moat exclusively conducted, are notoriously difficult and costly to drill. Despite this situation, however, with the high cost of developing new mines and extending existing mines, together with the rising cost of labour and mining problems resulting from the ever-increasing depths of workings, the demand for raise-boring in these formations is increasing rapidly. Not only is the demand for raises and shafts increasing, but also the length and size of these excavations. Raise-boring studies carried out in South African gold mines have indicated that increased penetration rates and possibly reduced costs could be obtained if higher thrusts were available at the reaming head. Until fairly recently there has been no raise-boring machine suitable for underground use that possessed the thrust and torque characteristics necessary to achieve high penetration rates in hard abrasive quartzite formations and the cutters available were not really developed for high loading. In response to these requirements a raise-borer, the Robbins 83R was designed and built in Seattle, U.S.A. for the Anglo American Corporation. This machine is operating in South African gold mines and is currently being used at a depth of 12 000 ft below surface in one of the. Group's mines. The initial raises bored have substantiated that increased penetration is attainable at high thrust and it is now apparent that the machine is sufficiently versatile to drill raises of up to 12 ft in diameter in quartzite formation over a length of 2 000 ft.

Jan 1, 1974

By Keith Schaeffer

This paper presents a history of the planning, engineering and construction completed for the railroad tunnel crossing part of the West Elizabeth Avenue Storm Drainage Project, undertaken to relieve flooding within the West Elizabeth Avenue area in Linden, NJ. The Railroad Crossing Contract is part of the larger Linden Drainage Improvements Project consisting of a new gravity storm sewer system. The improvements are required to provide additional storm drainage for the City of Linden and the Merck Pharmaceuticals manufacturing facilities in the City of Linden.

Jan 1, 2008

By Claus G. Goetzel

POWDER metallurgy is known as the art of producing metal powders and fabricating them in a nonfusion process by a simultaneous or consecutive application of pressure and heat under controlled operating conditions. Before the advent of powder metallurgy, the high melting points of the refractory metals and nonmetals made their manufacture and use practically impossible. Today, however, the uses of refractory materials in high-speed cutting tools, surgical instruments, brake linings, electrical contact switches, and filaments in incandescent lamps are commonplace in industry. Lately designers have even been turning to powder metallurgists to develop new techniques of fabricating refractory materials for extreme-service use in high-temperature zones of such modern products as gas turbines and jet engines. The new techniques being born will undoubtedly provide industry with a great number of new alloys and materials for future designing.

Jan 1, 1948

By M. J. Gilbey

Cross passageways between adjacent tunnels in passenger rail or transit systems may be used during train fire emergencies to evacuate passengers to points of safety in the non-incident tunnel. Rescue trains can be brought into the non-incident tunnel to remove passengers to expedite evacuation times as compared to walking along bench walls to the nearest egress stairs. In cases of multiple train emergencies, the required ventilation capacities can result in high pressure differences between the incident and non-incident tunnels. These pressure differences can make it difficult or impossible for a normal person to open doors of a cross passageway between adjacent tunnels. If opened, the velocity of the airflow through an open cross passageway can reach levels high enough to impede passenger evacuation. This paper describes the analysis of this problem for a sample rail tunnel. A ventilation concept that mitigates the problems of high cross passageway door opening forces and high velocities through open cross passageways is presented.

Jan 1, 2009

By J Lapwood, S Pal, M Pascoe

The devastating failure of Dam I at the Corrego do Feijao iron ore mine near Brumadinho in Brazil on 25th January 2019 left at least 270 people dead or missing. In the immediate aftermath of this event, many mining companies commenced reviews of their tailings and water storage facilities (T&WSFs), and Rio Tinto was no exception. Rio Tinto has an interest in over 250 T&WSFs across 47 sites in 13 countries as owner-operator, as managing JV partner, and through non-managed partnerships and other ownership arrangements; T&WSF experts from Rio Tinto’s Surface Mining Centre of Excellence visited the sites in order to complete Technical Risk Reviews of each facility. These reviews looked beyond the day-to-day operational aspects of T&WSF management, and the site’s compliance with local regulations and Rio Tinto’s internal D5 Standard – Management of tailings and water storage facilities, in order to provide a strategic, second line of assurance perspective. The reviews focused on design and construction; operational controls; risk control framework; and competencies and capabilities of personnel involved in the design, operation and closure of the facilities. Additional activities were carried out in parallel with these reviews, including the development of a consistent approach to dam break studies; the public disclosure of information on Rio Tinto’s tailings storage facilities and their management; and contribution to external programs such as the initiatives being co-ordinated by the International Committee on Mining and Metals. This paper provides an overview of the tailings and water storage assurance work undertaken by Rio Tinto’s Surface Mining Centre of Excellence Tailings Validation Taskforce to date; work that will continue to improve governance and assurance for all of Rio Tinto’s T&WSF.

Jul 1, 2021

By C. Swart

Automation technologies are increasingly adopted in different mines world-wide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHDs at Noranda?s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHDs and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda?s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Jan 1, 2002

By Za-Chieh Moh

This paper presents a summary of the current pile foundation practice in Taiwan. Constructions of driven piles, drilled shafts, and barrette foundations are reviewed. This paper also briefly summarizes the pile works of four major construction projects in Taiwan, namely, Hsin-Ta Power Plant, Taichung Power Plant, Taipei Transit Systems, and Taiwan High Speed Rail.

Jan 1, 1996

By Wood W, Bell A

Brown coal production in Victoria's Latrobe Valley Region (Figure 1) continues to rise and currently stands at around 50 Mt per annum. With the exception of around 2 Mt used to produce some 700 Kt of brown coal briquettes, this coal is mined by the State Electricity Commission to fuel large thermal power stations with a total installed capacity of just over 5 000 Megawatts. The moisture content of the coal as mined typically exceeds 60 per cent, making Latrobe Valley coal a markedly low rank fuel. The lack of heating value is, however, compensated for through power station design and by the fact that ash yield is very low, usually within the range of one per cent to four per cent on a dry basis. This means that compared with most other coals, the burning of Latrobe Valley brown coal produces relatively small quantities of waste products and discharges a minimal level of pollutants into the atmosphere. Even so, the inherent quality of Latrobe Valley coal does vary significantly from one area to another (Gloe, 1991; Barton et al, 1992) both on a local and a regional scale. Such variations need to be recognised and understood in order to not only realise efficiency gains in existing power stations but to properly assess resource potential for future utilisation and the application of new technologies. The principal aim of this paper is not to describe coal quality variation in detail or to speculate on the nature of and reasons for such variation. Rather, it is to simply underscore that significant differences do occur and that this is clearly a factor which needs to be considered in any evaluation of Latrobe Valley brown coal as a resource for the future.

Jan 1, 1992