Search Documents

By T. A. Rundle, K. Kim, W. M. McCabe, E. C. Gregory

Overcoring tests were conducted at the Near-Surface Test Facility(NSTF) to assess the suitability of five techniques (U.S. Bureau of Mines borehole deformation gauge (BDG), Commonwealth Scientific and Industrial Research Organization (CSIRO) hollow inclusion stress cell, Luleå triaxial gauge (LuH gauge), and Council for Scientific and Industrial Research (CSIR) doorstopper) for in situ stress determination in a closely jointed basalt. This effort is in support of the Basalt Waste Isolation Project, which is studying the feasibility of locating a nuclear waste repository in the basalts of the Hanford Site in southeastern Washington. This paper presents the results from the overcoring study that formed the basis for selection of two techniques to be used during the further exploration of the basalt formations at depth.

Jan 1, 1983

By Bain J. H

Since zinc was first deposited at Risdon in February, 1917, provision of the most economical cathode assembly has been a subject of extensive research, the major problems being corrosion and efficient use of power.From the corrosion viewpoint, a perfect cathode is one in which the life of the headbar and the deposition sheet are the same. However, corrosion usually concentrates in a narrow zone across the face- of the sheet, resulting in breakages which, before the advent of argon arc welding, meant a loss of a 'complete assembly.Attempts to extend sheet life included use of thicker sheets, multitudinous protective coatings applied with varying degrees of success, re-rolling, and for a time, aluminium consumption was reduced when broken sheets found re-use as protecting strips. This latter economy became impracticable when electrode spacing was reduced for greater efficiency in power utilization.As an integral part of the electrode, the headbar was modified accordingly. Copper headbars, although more corrosion resistant, were replaced by aluminium due to a possibility of dissolved, copper promoting deterioration.Thicker electrodes and regulated spacing reduced internal shorting, whilst provision of knife-edge type supports on both contact and insulator ends of headbars aided in electrode centralising and continuous electrical conduction.After much experimeIitation, an assembly has been evolved which, with the aid of argon arc welding and tbe use of minimum additional aluminium, permits comparable headbar and sheet lives, combined with good electrical conduction throughout the life of the cathode.INTRODUCTION Over 300 tons of zinc are produced daily at Risdon from a purified zinc sulphate solution by electrolysis, the zinc being deposited upon all-aluminium (except for copper contact) cathodes. It is stripped in 72-hour cycles from the cathodes, melted and cast into the customary rectangular slabs.

Jan 1, 1958

By Gustav Wafe

"INTRODUCTION The discovery in 1901 of ""gusher"" oil production at Spindletop, Tex., Tex., a salt-dome structure, led to exploratory drilling on other known domes and known domes and in areas contiguous to salt domes in the Gulf Coast region of Texas and Louisiana. Early drilling on the flanks of the domal structures disclosed incompetent 3/ shales, which flowed into the hole when attempts were made to drill through them. Often these shales seized the drill pipes and presented with equipment then in use, an insuperable barrier to deeper drilling. The obstructing incompetent shales came to be called ""heaving"" shales by drillers who attempted to drill through them. Formations of this type have hampered the penetration of the drill bit in many area in the Gulf Coast region to such an extent that the drilling of wells through heaving shale has become a major problem."

Mar 1, 1942

By Juno Gallego

A soldagem de peças de aço por arco submerso é um dos processos mais tradicionalmente usados na fabricação de componentes estruturais. A microestrutura do metal de solda é importante na definição das suas propriedades mecânicas, sendo a ferrita acicular um microconstituinte capaz de conferir à solda altos níveis de resistência mecânica e tenacidade. A nucleação da ferrita acicular depende da presença de inclusões não metálicas no metal de solda. No presente trabalho fez-se a caracterização microestrutural do metal de solda preparados com diferentes aportes térmicos. Lâminas finas foram observadas por microscopia eletrônica de transmissão, que possibilitou determinar alguns parâmetros morfológicos e químicos das partículas e a sua relação com a nucleação das ripas de ferrita acicular. Verificou-se que partículas irregulares com maior tamanho, mais ricas em titânio quando formadas com maior energia de soldagem, apresentam maior probabilidade de servirem como sítio preferencial para nucleação da ferrita acicular, se comparadas às partículas mais lisas e menores.

Aug 7, 2018

By J. M. Davidson, F. Fraas, J. E. Conley

"A number of Reports of Investigations pertaining to the extraction of potash from cal¬cined polyhalite have been made by various members of the Nonmetallic Minerals Experiment Station of the United States Bureau of Mines. These reports describe results obtained in the study of samples of polyhalite (2CaS04.K2S04.MgS04.2H20) from deposits of possible com¬mercial importance in Texas and New Mexico.3Storch and Clarke6 in their initial paper presenting data on the properties of Texas polyhalite demonstrated the desirability of calcination and subsequent hot extraction with water as a satisfactory pronedure for treatment of this potash-bearing salt. Their preliminary data have been supplemented by an additional report7 dealing more particularly with the leaching of raw and calcined polyhalite with water and with saturated sodium chloride solu¬tions. Further data8 have been reported as a result of experiments made in a small labora¬tory rotary-tube furnace under various calcination and extraction conditions. Hot water was used as the leaching solution in all of these tests.In addition to the data on calcination and extraction, two processes as proposed by Storch and Clarke have been published by Wroth,9 and more recently a number of very promising processes have been proposed by Storoh and Fragen.10"

Apr 1, 1932

By B. J. Moore

This publication contains 14,242 analyses of gas samples from oil and gas wells and natural gas pipelines in 40 States and 24 foreign countries. These gas samples were collected in the period 1917-85 as part of the Bureau of Mines survey for helium occurrences. The gas analyses contained herein were made by several methods over the period covered. Analytical work on samples collected early in the period was done on the Orsat apparatus. The one-cut apparatus and four-cut fractional distillation equipment were added later. A mass spectrometer was acquired in 1949 and used for all gas analyses made after that time. From 1917 to 1978, helium analyses were made on special helium analytical equipment designed and built by the Bureau of Mines Helium Operations Laboratory. In 1978, this apparatus was replaced in the quantitative helium analysis work by a gas chromatograph.

Jan 1, 1987

By M. L. Bakker

Keywords: Pyrometallurgy, top submerged lance (TSL), nickel, PGM, calcium ferrite, lime ferrite The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 9 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, whereupon it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and Platinum Group Metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By F. Ziaie

Line electrical resistivity method using physically infinite distance between current line electrodes is proposed to determine the location of mine workings. In this method at least three line electrodes are used. One of the current electrodes is used as a sinkhole electrode while the other two are used for different activiations of line electrodes when the survey area is between one of the line electrodes and outside the other one. The resistivity profiles perpendicular to the current line electrodes for different activation of electrodes is plotted versus the distance of the midpoint of the measuring potential electrodes. The anomaly due to presence of any locally lateral resistivity variation (e.g. mining cavity) will represent itself as peak or trough depending on resistivity contrast between the source of the anomaly and surrounding medium. Physical simulation of the proposed model was conducted by using a tank model in the laboratory. The results of experiments appear to be consistent with the theoretical model. Experiments for different depths and different spacial locations of the simulated cavities appeared to be successful for locating the depth and size of the cavity.

Jan 1, 1989

By C. Özgen Karacan

The formation of the gas emission zone in longwall mining and the potential amount of gas in this zone are factors of local geology and spatial variability within this geology. Therefore, geostatistical methods can be used for modeling and prediction of gas amounts and for assessing its uncertainty in the gas emission zone of longwall mines. This study used core data obtained from 64 exploration boreholes drilled from the surface to the bottom of the Pittsburgh coal seam in a mining district in the Northern Appalachian basin. After identifying important coal layers for the gas emission zone, semivariogram modeling was conducted for different coal seams to define the distribution and continuity of various attributes. Sequential simulations were performed for stochastic assessment of these attributes to calculate gas-in-place (GIP) in each coal seam. GIP calculations for coals of various gas emissions zones were combined and ranked for their cumulative distribution function to find GIP in the caved zone and in the fractured zone at the 5%, 50%, and 95% quantiles. Fifty percent quantile results were later used to isolate a panel from the whole area and create a mosaic representation corresponding to the daily advance rate of the longwall face. This approach helped to estimate the daily emissions of this panel from the caved zone and from the fractured zone. Results showed that gas-in-place in the Pittsburgh coal seam, in the caved zone, and in the fractured zone showed spatial correlations that could be modeled and estimated using geostatistical methods. This study showed that gas-in- place volumes in the study area may be as high as 12.3 Bscf and as much as 3.5 MMscf per acre of mining.

Jan 1, 2012

By Peter Dowden, Trevor Carter, Allan Moss, Bruce Downing, Richard Beddoes

Traditionally (with a few exceptions) tunnel boring machines (TBMs) have been utilized on tunnel projects where the risks associated with deep tunnels (rock burst, squeeze, etc) are low (or expected to be low). This has generally been due to the extremely adverse consequences of entrapping or damaging a TBM under such conditions; but also due to the relative difficulty of dealing with these ground conditions in the confined working area of a TBM, in comparison to a drill and blast heading. This paper review the constraints of operating a TBM in a deep tunnel and discusses related project experience, particularly recent and current experience with TBMs in the deep Alpine Base Tunnels. Potential future applications of TBMs in the development of large, deep underground mines are also discussed.

Jan 1, 2007

By V. E. Dawson

Brake testing of large mining trucks was initiated in British. Columbia in 1969 following an accident involving the failure of the service brakes of a l00-ton electric-drive truck. Some selected results of the 1976 brake test program are presented and discussed ?in this paper . The tests were conducted on end- dump trucks having load capacities ranging from 85 to 235 tons. All tests were made with the vehicles fully loaded operating on downhill grades varying from 8 to 10 %. Stopping distances were measured from initial speeds varying between 10 and 39 mph. The results are adequate, in most cases, to determine the "ultimate" capabilities of the service brakes of varying models and sizes of haulage trucks operating in British Columbia mines.

Jan 1, 1977

The past decade has seen revolutionary advances in communications and information-handling techniques which have been stimulated by "cold war" military requirements and by current programmes for probing into outer space. The tools used in exploration for petroleum and minerals have been improved significantly as a result of this new space age technology and even greater improvements are on the way.Two areas of technical activity have been particularly fruitful in enhancing the effectiveness of exploration methods. These are1. the development of new approaches, based on information theory,for extracting signal from noise more efficiently than before, and2. the use of high-speed digital computers for storing and processing all kinds of exploration information, not only geophysical but geological as well.In seismic prospecting, use of information theory has led to new techniques such as time-domain filtering, wave-number filtering and correlation methods which have made it possible to obtain usable reflection data from areas which were previously considered non reflective. Complex playback and other data processing facilities have been developed to apply these approaches.Digitization of geophysical data for handling by high-speed electronic computers facilitates many of these techniques for signal-to-noise improvement. Direct digital recording of seismic data in the field is now being d'one on an experimental basis in the United States, and this should become a standard procedure, at least for problem areas.The increased dynamic range, flexibility of filtering and other data processing, and convenience of information storage and retrieval make digital recording attractive in spite of its high cost compared to conventional analogue methods. Digital computers are being programmed to carry out many operations in data reduction and interpretation with substantial savings in time and cost over conventional procedures.INTROPUCTIONIn the years that have passed since the end of the Second World War, the western world has witnessed a technological revolution which may be as far reaching in its ultimate impqct as the Industrial Revolution of the last century.

Jan 1, 1963

By J. C. Edwards

The National Institute for Occupational Safety and Health (NIOSH) implemented a real-time neural network system which can discriminate mine fires from nuisance diesel emissions as part of an atmospheric mine monitoring system in NIOSH?s Safety Research Coal Mine. The real-time response of a neural network to fire sensor outputs was demonstrated for coal and belt combustion in the presence of diesel emissions. The fire sensors consisted of an optical path smoke sensor, a carbon monoxide (CO) sensor, and two types of metal oxide semiconductor (MOS) sensors. The real time neural network was trained with coal, wood, and belt fire experiments with and without diesel emissions background. The trained neural network successfully predicted mine fires with these combustibles in the smoldering stage prior to the onset of flames.

Jan 1, 2005

By R. C. Corey

GERMANIUM is an element that has come into widespread use in the electronics industry in recent, years. So far this increasing demand has been, met by ample supply: however, the future balance is uncertain, and the need has been recognized to discover additional domestic sources of germanium. This investigation was conducted to study the possibility of obtaining a potential supply of germanium from coal or coal ash. It has been known for some time that coal contains germanium; the discovery that By ash from coal-fired boilers often contains appreciably more germanium than the original coal suggested the possibility that coal ash might be an abundant and economical source of this element. In this study the concentration of germanium was determined in numerous samples of coal and ash. A number of miscellaneous waste materials also were examined in the course of the investigation; the results are reported as a matter of general interest. The methods and equipment employed are discussed in detail. Sample-preparation and analytical techniques are described in the appendix. Spectrographic analyses were made on a total of 639 samples, including coal, coal ash, slap ash from lignite and peat, wood ash, and various inorganic materials. Qualitative analyses were run on all samples, and quantitative determinations were made on those samples that contained enough germanium to be measured by this method The lower limit at which germanium can be determined quantitatively by spectrographic analysis is 50 parts per million (p. p. m.), but concentrations of less than 20 p. p. m. can be detected qualitatively.

Jan 1, 1959

By Gregory M. Molinda

Extremely difficult ground conditions were encountered in the main belt entry in a room and pillar mine in West Virginia. Several generations of supplemental support, including cable bolts, cribbing, and Heintzmann jacks and beams failed to halt roof falls that threatened workers safety and the life of the mine. Polyurethane (PUR) was injected into 27 intersections in the roof and the results were monitored by borehole video camera. The mine had averaged 2-3 falls in the beltway per year and, since the roof injection, no roof falls have occurred. Pre- and post injection monitoring of test holes showed that stability can be achieved without filling all of the existing void spaces. Video logging showed that the project goal of building a beam from 2-6 ft into the roof was successful. Pre-injection monitoring of roof fractures uphole can delineate the zones to target for reinforcement, and avoid pumping PUR into large voids to little effect. Multiple-injection zones can be identified, and the entire intersection drill hole array can be optimized based on knowledge of the fractured zones. In addition, pre-monitoring can prevent excessive hydrofracturing in solid zones. Polyurethane injection is a proven method of rock stabilization in even the weakest, most broken ground. Optimization of the injection design by pre-injection video diagnostics can greatly contribute to the successful and efficient roof stabilization.

By Dee Bradshaw

"Process mineralogy’ is a form of applied mineralogy which focuses on addressing problems associated with the processing of ores. ‘Mineralogy’ is the scientific study of minerals and ‘mineral processing’ is the production of concentrates from ores. ‘Process mineralogy,’ however can be defined as the practical study of minerals associated with the processing of ores, concentrates and smelter products for the development and optimisation of metallurgical flowsheets, including the waste and environmental management considerations. This hybrid discipline consists of teams that include geologists, mineralogists, samplers, mineral processors and often others, working together. The degree of cross-training, communication and trust dictates the potential capacity of the team and where an appropriate work dynamic is fostered, in which relationships flourish as much as does the ethic of technical excellence, it is possible to develop technical capabilities that surpass those of conventional teams. The world’s demand for metals is ever increasing and ore deposits available for extraction and processing are lower grade and more complex, often containing deleterious elements that require tailored treatment. Generally, in the past, the technical challenges only needed to be overcome and assessed economically to make an ore deposit viable; increasingly and in the future, a more sustainable approach including environmental and societal considerations is needed. Process mineralogical assessment is increasingly providing the critical information that stands between failure or collapse and survival or success of some mining operations. In this paper, selected case studies are used to demonstrate the valuable role of the process mineralogy tools being used to provide the platform for innovative technology development. Their common attributes are discussed and distilled, thus providing some insights and potential guidance for addressing some of the likely future challenges of the mining industry."

Jan 1, 2014

By Arthur E. Morris

The primary market driver for improving process technology is innovation, which requires a skilled and educated workforce. However, many Materials Science and Engineering departments have eliminated extractive metallurgy and chemical thermodynamics from their curricula, yet these topics contain the necessary fundamentals for process innovation. As a result, most MS&E students are ill-prepared for careers in processing. The dearth of processoriented MS&E curricula has prompted some Universities to develop a “shared” effort to offer distance education between multiple institutions [1]. A target audience for a shared process simulation course would not only benefit students, but also be a basis for an on-line course for practicing engineers faced with new or changing career choices. To fill the gap, the basics of a process simulation course was developed in an abbreviated form as series of eleven articles and Excel workbooks published in Industrial Heating magazine between July 2012 and July 2013.

Jan 1, 2014

By H. McSorley

"I note that many of you are involved in the production of zinc, lead and copper concentrates and metal, which I am the most familiar with among the non-ferrous metals. This afternoon, I will describe briefly the responsibilities of a commercial manager within a mining/metallurgical company, the basic framework of a non-ferrous metals concentrate agreement and lastly, a brief discussion of the copper, zinc and lead concentrate and metal markets.I hope this talk will contribute to a better understanding of the business between all of us and look forward to a discussion after the presentation.First of all, I work for Noranda Sales, which is the marketing and sales agent for Noranda Minerals' three operating units: Noranda Copper, Noranda Zinc and Mining Corporation. In addition, Noranda Sales acts for other mining companies in the marketing of their raw materials and metals. Noranda Sales is responsible for procuring all raw materials for Noranda's metallurgical plants, such as the Copper Group's Forne and Gaspe smelters, as well as the sale of surplus concentrates and by-products and metal products. In addition, Noranda Sales trades metals and concentrates and owns a metal brokerage business, Rudolf Wolff, a founding member of the London Metal Exchange. It does $3 billion of business in 60 countries, exporting some 80% of Noranda Minerals' output to the world.What are the responsibilities of commercial management in resource marketing to the mine and metal producers?Resource marketing and commercial administration involves assistance in establishing exploration priorities, contributing to feasibility studies, pre-production planning, product promotion and realization of income for many properties and metallurgical plants through completion of supply and sale agreements with other companie"

Jan 1, 1988

8186. Aquilina, C. Determinazioni relative di gravita eseguite nel 1939 (Relative Determinations of Gravity Made in 1939), Ric. Ingegn, Rome, vol. 10, 1942, pp, 6376. In 1939, the author made a survey of relative gravity in the Mediterranean-basin, 41° 35,5' to 41° 56.3' northern latitude and 0° 10,3' to 0° 28' longitude, referred to Mt. Mario. Ten stations were covered; 25 other stations had been occupied in the vicinity of Rome and in Albanian mountains during previous years. The new measurements revealed gravity anomalies ranging within the following limits: (1) With a free-air reduction, between + 29 and + 120 mgl., average + 60 mgl.; and (2) with a Bouguer reduction, between + 22 and + 87 mgl., average + 41.5 mgl. - V. S.

Jan 1, 1946

By F. H. Buchella, J. F. Buchanan

The San Manuel copper deposit is located about 45 miles northeast of Tucson. The concentrator, smelter, administration building, and other plant facilities are located about seven miles southeast of the ,nine area at the new town of Sari Manuel as shown on Figure 1 (Sketch).

Jan 1, 1961