Search Documents

By C. Musingwini

Traditionally, mineral reserves management at most underground mines in Zimbabwe focus on maintaining large mineral reserves so that the time between development and production is as long as possible. Historical data at Shabanie mine, a Zimbabwean sub-level caving underground mining operation, confirms this practice. However, the high cost of underground development means that the luxury of large buffer mineral reserves cannot be justified. Furthermore significant increases in the costs of production, exacerbated by the current unfavourable economic climate, make the wisdom of extending development workings well ahead of use questionable. Poor ground conditions at Shabanie mine, mean that some development ends have to be re-mined two or three times due to partial or complete closure between the time they are mined and the time they are utilized. In order to reduce the inordinately high support costs associated with closure of development ends a new ?just-in-time? (JIT) approach that provides development ends as and when they are needed, has been adopted. Accordingly a model to determine an appropriate ?just-in-time? rate of development has been created. The JIT development model indicated that the mine could reduce development rates from 330 m/month in 2001, to 160 m/month in 2002 and achieve savings of about 50% on annual support costs, but still assure customers of a long-term product supply. The mine accepted the model in November 2001 and began implementing it in 2002. Results of the implementation will be reviewed in 2003.

Jan 1, 2003

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives involve several potential pitfalls. These are outlined in the present paper.It was found that coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate. For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition. Significant errors could be incurred if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen).For elemental analysis determination, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range. For representation of sulphur in coal, one should avoid doublecounting due to SO3 in the ash analysis.Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2.However, use of some of these species without considering the experimentally determined gross CV leads to significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy. Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than these four, provided the enthalpy is corrected.It is recommended that an ‘enthalpy correction value’ be incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to carbon being present in a form other than graphite should be used, as that would imply double-counting some effects."

Jan 1, 2015

By Werner Burger

Earth Pressure tunnel boring machines are tackling difficult ground conditions that five years previous were not considered feasible. The technology has evolved that allows EPB TBMs to cross into areas that with the latest in conditioning and special design considerations are now possible to mine. This paper will review the various recent developments and those projects where these new techniques have been applied.

Jan 1, 2008

By W. T. Malone, J. R. Williams, R. L. Tiner, J. M. Tinsley

Hydraulic fracturing methods for production stimulation have become a common procedure in the oil and gas industry. Fracturing treatments are performed on wells of various potentials to help increase the production rate. In addition to the desire for increased production is the need to predict what increase might be expected. This knowledge is useful in economical treatment planning to accomplish the desired production goals for the well. Theoretical production increases due to horizontal radial fractures may be calculated using equations developed from mathematical analyses and electrical models.1,2,6 It also is possible to predict theoretical production increases due to vertical fractures using curves developed from electrical3 and mathematical models.8 However, these studies assumed that the vertical fracture height and the formation height were equal, which may not be true." In addition, the final fracture height through which fluid is produced may not be equal to the created height. The development of vertical fracture proppant transport relationships has made unrealistic the assumption that propped fracture height is equal to created fracture height. Through the use of published proppant transport equations,4'12 it is possible to calculate the height of a bed of propping agent deposited in a fracture of a given height. Assuming that the fluid flowing in the fracture moves through only the propped portion of that fracture (i.e., that the un-propped part of the fracture heals) it becomes essential to know how production increase varies with the ratio of propped fracture height to formation height. It should be recognized that future investigation may determine that the fracture does not heal completely and that a highly permeable channel exists over the deposited bed of proppant. The effect of this channel was not considered for the present study. The following analysis of experimental data allowed development of curves to determine theoretical production increases considering fracture height as a variable. Discussion In designing a fracturing stimulation treatment a number of variables must be considered. The size of the treatment, type of proppant used, proppant concentration, treatment fluid properties and well conditions are all factors affecting the dimensions and permeability of the fracture. Production increase due to a vertical fracture is affected by propped length, height, width and permeability of the fracture for a given set of formation conditions. Production increase may be defined as the ratio of production rate after fracturing to the production rate before fracturing at the same pressure differential, pe — pw. The producing rate in an

Jan 1, 1970

By A. J. Thompson

The Metropolitan Transportation Authority (MTA) East Side Access project (ESA) will, when it is complete, provide a new link to the east side of Manhattan from Long Island, NY that, linked with the Second Ave. Subway currently under construction, will assist in relieving overcrowding at Penn Station as well as the Lexington Ave. subway. ESA will bring Long Island Railroad (LIRR) directly from Long Island into a new station located 37 m (120 ft) beneath the existing Grand Central Terminal (GCT) located in the heart of Manhattan. It will connect the LIRR?s mainline tracks in Queens, via the existing 63rd Street Tunnel under the East River, to a new terminal constructed within, and beneath, the historic Grand Central Terminal.

Jan 1, 2012

On-stream determination of xanthate concentrations can be made by photometric measurements at 313 nm.A simple double-beam instrument was developed for this purpose. A mercury lamp is used as the light source and a composite filter of UGll glass and chromate solution is used to isolate the required spectral region. The light beam is split into two components of approximately equal intensity. One component is passed through a reference cell containing water to a photo detector; the other component is passed through the xanthate solution to a second photo detector. The reference signal controls amplifier gain to eliminate effects of lamp intensity changes and the amplified sample signal can then be used to measure xanthate concentration.Plant trials showed that provided a clear solution free of air bubbles was obtained from an on-stream filter, the instrument indicated the xanthate concentration and operated satisfactorily for long periods.

Jan 1, 1973

By J. O. Marsden

Parts I and II in this series of papers presented the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical development of a process to effectively recover copper using medium-temperature pressure leaching and direct electrowinning (DEW). Part III reviewed the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona. Key features of the process were the use of superfine grinding of the concentrate (to a P98 of 12 to 15 µm and a P80 of 6 to 7 µm), pressure leaching at 160ºC with 1,380 kPa (200 psig) oxygen overpressure, DEW to produce LME Grade A cathode, recycling some of the lean electrolyte to the pressure leaching step, and treatment of a lean electrolyte bleed by solution extraction (SX). Recycling of lean electrolyte provided all of the acid required to effectively dissolve copper and convert approximately 65% to 70% of the sulfide sulfur to elemental sulfur, resulting in an acid-autogenous process for pressure leaching. This paper (Part IV) discusses the development and design of a full-scale commercial application for the Morenci operation in Arizona.

Jan 1, 2007

By I. Ocak

The modulus of elasticity of rock material (Ei) is an important rock property that is used as an input parameter in the design stage of engineering projects such as dam and tunnel constructions, mining excavations, and so forth. However, determination of the modulus of elasticity is sometimes difficult to obtain by laboratory tests because high-quality cores are required. For this reason, empirical methods for predicting the modulus of elasticity of rock material have been popular research topics in recently published literature. In this study, the relationships between the uniaxial compressive strength (UCS), unit weight (?) and modulus of elasticity for different types of rocks were analysed by using 177 data obtained from laboratory tests carried out on cores obtained from drill holes within the area of the Kadiköy-Kartal Metro line (Istanbul, Turkey). Keywords: Kadikoy?Kartal Metro, uniaxial compressive strength, unit weight, estimating the modulus of elasticity.

Jan 1, 2008

By J. M. Benson

Titanium is an exciting structural material that can offer significant strength-to-weight advantages over currently used alloys. However, its Achilles? heel is its costly, energy-intensive production process that effectively eliminates it from competing with aluminium and high-strength steels, apart from critical applications where titanium forms only a small component of the total cost. Current attempts are being made to reduce the cost of titanium products and these recognize the importance of minimizing the costs over the total production chain. Powder metallurgy (PM) technologies play a crucial role within this, as the output of the existing and potential primary metal production methods is in the form of sponge or powder. By using PM, costly remelting and forming operations can then be avoided, except in the manufacture of large components. Metal injection moulding (MIM) is an effective process for producing complex net-shape components in large volumes from metal powders. Nevertheless, the commercial use of titanium powders in this process is still in its infancy. The only major supplier of feedstock utilizes a polyacetal-based binder. This gives good green strength but requires a catalytic nitric acid process to remove most of the binder prior to thermal treatment. As this involves additional and expensive equipment and is a potentially hazardous process, there is interest in finding an alternative binder system that can be debound either purely thermally or that involves a less hazardous, more environmentally friendly solvent. This paper describes the use of capillary rheometry to characterize the influence of temperature and shear rates on the flow behaviour of potential binder systems for titanium MIM feedstock. Keywords Titanium, metal injection moulding, capillary rheology, feedstocks, powder loading.

Jan 1, 2011

By Kazunori Matsushita, Frank Vespi, Emi Walder, Mitsuo Nozu

During the runway expansion project at the Fort Lauderdale-Hollywood International Airport in Florida (FLL project), therewere complicated geotechnical issues with a number of cavities in the limestone-loose sand mixed ground thatexisted in many areas below the existing ground. Collapsing the cavities and compacting the runway foundation to secure the take-off and landing of aircrafts was a necessary requirement for the project. The Mammoth Vibro-Tamper (MVT) which produces less vibration and noise level, was proposed and accepted as the alternative to the originally specified Deep Dynamic Compaction (DDC) for the runway with its length of 1.5 miles and area of 570,000 square yards. In this report, the shallow compaction effect and reduced ground vibration with the MVT are presented in comparison with the DDC which was utilized on the same project in a different area of the airport. INTRODUCTION MVT was developed by Fudo Tetra Corporation in the 1960’s and has been widely used in Japan (more than 14,400,000 square yards). For example, at the Kansai International airport, a large area including aprons was compacted with the MVT. It is capable of compacting up to approximately 5m in depth by using a heavy steel plate (3m x 3m) and a strong vibrator motor (V-180, 10Hz) on top of the steel thick plate with specified time duration. We were involved in densification work with the MVT at the Fort Lauderdale Airport Project (Figure 1) from June, 2012 to February, 2014. Deep Dynamic Compaction (DDC) was originally specified as the compaction method to secure the relative density over 70% in every 2,000 square yards grids, however, we proposed the application of MVT to reduce the vibration risk and it was accepted as the alternative (Figure 2). The compaction work was completed in February 2014, without causing any delay in regard to the residual settlement due to the high embankment (H=60ft=18m).

Jan 1, 2018

By P. Golledge, A. D. S. Gillies

An investigation has been carried on samples of three Queensland coal dusts to determine the potential explosibility of dust-gas mixtures. The explosion potential of the samples was classified by the lean and rich limits of explosibility and the limiting oxygen concentrations for each sample. Plotting of these points showed 2-dimensional flammability limit surfaces for coal dust/oxygen, methane/oxygen and coal dust/methane mixtures. From these plots the 3-dimensional flammability envelopes defining the explosibility of the mixtures were defined. The explosion limits of the coal dust/methane/oxygen system were seen to be influenced most by the explosibility characteristics of coal dust. Methane exerted a stronger influence over the explosion limits when the coal had a low volatile content

Jun 19, 1905

By Vasile Pop, Ovidiu Galca, Constantin Salajan

The paper comprises a brief presentation of the rock fracturing techniques applied in CNMPN “REMIN” Company’s mines in Baia Mare. Parallel are emphasized some shortcomings of this field. The second part of the paper includes our preoccupations and achievements, of the last period, in especially those linked to techno-economical indices improvement resulting from the development of relatively large section mining works and blasting applied with sublevel caving methods.

Jan 1, 2003

By Takuya Taguchi, Toshihiro Ogata, Atsuio Inoue, Shigeyuki Sasaki

Highly improved drilling machines and mucking machines have been used for the underground construction. To have rapid construction, the roles of blasting operation ha ve been growing more important. At the most tunneling of present, cartridged emulsion explosives have been used for a blasting in Japan. Under this circumstance, a blasting system of ANFO explosives using loading machine has been used recently for a tunnel blasting. However, ANFO has some problems, such as a useless explosives in wet boreholes, bad blasting fumes and the ammonia gas due to the decomposition of ammonium nitrate in contact with the sprayed concrete in tunnel.

Jan 1, 2005

By W L. Jennings

This paper summarises work undertaken to date as part of an investigation into the mineral resources of the proposedNorth West South Island National Park. The area covered by the proposed national park is underlain by many rock types that have undergone a long and complex history of evolution which has endowed it with some of the best potential for a wide range of different minerals in New Zealand. Many of these minerals occur only in this area or in Fiordland National Park.   The first gold-rush in the area occurred in 1856 and followed the discovery of payable gold at Lightbands Gully, south of Collingwood. The miners first focused on the alluvial deposits but soon shifted attention to lode potential. The total historical gold production for the area may be over 400 000 oz (NZ$250 - NZ$295.6 M at 1993 prices).   In addition to gold, a wide range of other minerals have been reported from the area including molybdenum, copper, nickel, zinc, silver, bismuth, stibnite, lead and antimony. The Onekaka iron-ore deposits have produced small tonnages of ochre and iron-ore at various times. Tungsten, platinoids and other metals have been. given only minor attention. The diverse geology of the Northwest Nelson has resulted in the occurrence of many industrial minerals which have been exploited in generally small-scale operations. Aggregate, chrysotile asbestos, clay, dolomite, marble, limestone, dimension stone, rip-rap, talc-magnesite and wollastonite have all been produced.

Jan 1, 1993

By K. Zenger, J. Kaartinen, J. Huuskonen, S. Torttila, S. Lähteenmäki, J. Pietilä

"Pyhäsalmi Mine in Finland has a long history of continuous process development. The concentrator processes Cu-Zn-sulphide ore with high recoveries. An on-line flotation simulator has been developed to maintain and further improve the flotation performance. Consisting of a flotation kinetic dynamic model, and interconnected with process control software, the simulator can be used for training new control room operators in various scenarios. For daily operation, the model parameters are continuously adapted to take into account the changing process conditions. On-line simulator tracking the process can provide the process operator new information in several ways: a) values of unmeasured process variables are obtained by displaying the corresponding simulator values, b) predictions of future process states and outputs are calculated and displayed, c) information of changing process parameters can be used as an indicator of e.g. change in the processed ore type. This paper describes the adaptive simulation system and its usage at the Pyhäsalmi concentrator.IntroductionPyhäsalmi massive sulphide orebody is located in central Finland. Operation of the mine started in 1962 and it is currently producing copper (Cu), zinc (Zn) and sulphur (S) concentrates. The concentrator control and optimization system has a long history of successful continuous development during the past decades (see e.g. Huuskonen & Moilanen, 2010). An on-stream analyzer has been a part of the automatic process control since 1968 (Lähteenmäki, Miettunen & Saloheimo, 1999). First control algorithms based on a flotation mathematical model were developed in 1971 (Koivistoinen & Miettunen, 1985). In 1990’s the development of a froth machine vision systems started (Kaartinen, 2009; Kaartinen, Roine & Hätönen, 2009). More recently Pyhäsalmi Mine Oy has been involved with several national development projects dealing with particle size distribution measurements (Kaartinen & Tolonen, 2008), spectral analysis of flotation slurries (Haavisto, Kaartinen & Hyötyniemi, 2008), and dynamic simulation of flotation processes. The latter topic is further elaborated in this paper."

Jan 1, 2015

1. Domestic Production and Use: In 1974 twelve companies operated 31 primary aluminum reduction plants, three firms accounting for 64% of production. Washington, Oregon, and Montana accounted for 32% of the total production; Gulf Coast States, 24%; Northern States, 33%, and other Southern States 11%. Output of primary metal in 1974 was valued at $3.4 billion. About 80% of the secondary recovery was from new aluminum base scrap and 20% was from old scrap. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1974, building accounted for about 27%; transportation 19%; electrical, 13%; packaging, 15%; and consumer durab1es, 9%.

Jan 1, 1975

By J L. Maule, S J. Mathews, K A. Rodgers

Gold and Silver bearing epithermal veins of the Golden Cross deposit are hosted in Miocene and Pliocene calc-alkaline volcanics occurring 8 km northwest of Waihi at the southern extent of the Coromandel Peninsula, North Island, New Zealand. Veining occurred during a period of hydrothermal activity that began early to late Pliocene, and possibly continued into the Pleistocene.   Field relations and petrographic relationships reveal that multiple generations of FeS2 occur in the Golden Cross region, with FeS2 occurring in all nine rock types recognised at Golden Cross. The variability of FeS2 morphology was investigated by preparation of high purity FeS2 separates, and grain counting. Marcasite is the dominant FeS2 phase at Golden Cross, and along with pyrite is shown to have a systematic habit variation. Pyrite shows a sequence from cubes through octahedra to pyritohedra to dendritic growth. This pyrite sequence conforms to an experimentally determined sequence. The parallel sequence for marcasite at Golden Cross is from tabular through bladed aggregates to euhedral miscellaneous marcasite morphologies. The FeS2 sequences observed are believed to be due to increasing temperature, and perhaps also increasing FeS2-oversaturation and fluid flow.

Jan 1, 1994

By Jamey B. Rosen

As Project Information Management Systems (PIMS) technologies develop, the range of projects to which one can apply these technologies grows while the cost to apply them shrinks. In recent years, technologies previously limited to large “megaprojects” (e.g., major dam rehabilitations) owned by major entities (e.g., the United States Army Corps of Engineers) with large budgets have been applied to smaller projects with less stringent specifications and more modest budgets. This paper will describe applications of PIMS technologies to small projects with limited budgets, including examples from levee construction, small-scale grout curtain installation, and diaphragm and secant pile cut-off walls. We will include a demonstration of how PIMS technologies can effectively analyze verticality data from koden and hydromill data streams to automatically generate models and as-built drawings showing overlap and deviation along the depth of the foundation. INTRODUCTION This paper discusses the application of Project Information Management Systems (PIMS) technologies to geo-foundations projects, with a focus on technologies and examples that are in a lower cost range. PIMS technologies allow contractors and other stakeholders to perform efficient quality control on their data, generate quick or automatic reports and as-built drawings, perform analyses to better understand their construction, and ultimately use their data to increase the quality of their construction. As PIMS technologies are relatively new to the deep foundations industry, and owner specifications on their use are generally viewed as complex and limited to large scale projects, PIMS technologies are frequently viewed as an expensive component that is beyond the scope of a smaller or simpler project. However, the same principles and techniques generally associated with large projects can be applied to projects at smaller scale. Furthermore, as these technologies develop both in the deep foundations and other industries, the cost of application is decreasing quickly making them even more affordable for smaller projects. The remainder of this paper provides some justification for applying PIMS technologies, describes some scalable data management concepts and workflows and then provides some examples of “low cost” applications of these technologies.

Jan 1, 2019

By Christopher J. Bise

INTRODUCTION Perhaps no other area reflects the art as well as the science of mining-engineering design quite as obviously as strata control. This is due to the fact that the design of mining structures is difficult because rock rarely behaves as a homogeneous medium. Further, the original state of stress and the mechanical proper- ties of the in situ rock are somewhat difficult to deter- mine. However, those aspects that are hard to treat mathematically can and have been successfully approached by model studies and in situ measurements. This chapter will review the fundamentals of strata- control design and will provide examples of applications to typical problems. STRESSES AROUND MINE OPENINGS A close examination of Fig. 1 reveals that, prior to mining, stresses exerted in the overburden can be in both the horizontal and vertical directions. In the example problems of Chapter 1, it was shown that the maximum compressive stress (uv) at any depth (D) below the surface can be approximated as follows: [ ] Further, the lateral stress (oh) is related to the maxi- mum compressive stress by utilizing Poisson's ratio (µ): [ ] As soon as a heading is driven, such as the one in the coal seam shown in Fig. 2, the stresses shift to the sides, or abutments, of the opening. Clearly, these compressive stresses around the opening exceed the pre-mining conditions. The problem of designing an underground opening, therefore, is to determine the maximum stresses and to note if they exceed the ultimate strength of the rock. Table 1 lists several rocks with their corresponding strengths. Figs. 3 to 5 depict the boundary stress concentrations around circular, ovaloidal, and rectangular openings. M is the ratio of the horizontal stress to the vertical stress, or as defined above, p/(l-p). This text will concentrate on the state of stress represented by M = 0.33, which corresponds to the condition of no lateral deformation in a rock having a Poisson's ratio of 0.25. For an ovaloid with an opening width-to-height ratio of 2.0 (Fig. 4), the boundary stress concentrations are at their maximum values at the comers of the opening, with values in excess of 3.0. If the depth of overburden is 500 ft, then the maximum boundary tangential stress ([ ] ) of the ovaloid is: [ ]

Jan 1, 1986

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

The wetting characteristics and water film stability at the talc surface have been studied, particularly the effect of polysaccharides such as guar gum, starch, and dextrin. Talc is a gangue mineral in the flotation of base metal sulfide ores, precious metal sulfide ores, and platinum group metal (PGM) sulfide ores. Talc surfaces were investigated using surface analysis techniques including atomic force microscopy, high-speed video bubble attachment measurements, and wetting film stability measurements using a synchronized tri-wavelength reflection interferometry microscope (STRIM). In the presence of polysaccharides, there is a significant increase in bubble attachment time at the talc surface, but only a slight change in contact angle, which suggests that polysaccharide depression of talc is due primarily to the slow rate of bubble attachment and not due to a change in contact angle. The critical rupture thickness (hc) for a hydrophobic talc surface was found to be 56 nm, while the hydrophilic phlogopite surface of similar structure has an equilibrium film thickness (he) of 25 nm. At low polysaccharide concentrations, the wetting films formed on the talc surfaces were unstable, but at high concentrations the wetting films became stable with similar thickness values as the critical rupture thickness, and bubble attachment did not occur. However, it was found that the critical and equilibrium film thickness values do not change significantly with the polysaccharide type or concentration. The results from this research help us understand further details of film rupture and displacement during bubble attachment.