Search Documents

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012

By Douglas D. Campbell, Alan S. Imrie

INTRODUCTION Mica Dam is located on the Columbia River just downstream of the "big bend" of the Columbia, where it leaves the Rocky Mountain Trench and begins to flow southwards, approximately 85 miles north of Revelstoke, B.C. (Fig.l). The dam was built as one of three Columbia River Treaty dams in British Columbia which regulate the flow of the river and provide flood control downstream in Washington and Oregon. In addition, the three Canadian dams make possible greatly increased power generation at existing power plants in the United States and further development along the Columbia and its tributaries in British Columbia. History Mica Dam, constructed during the period 1967 to 1973, is a zoned earthfill embankment 650 feet high, which has 12,000,000 acre feet of live storage and an available head of 550 feet. Power intakes which would serve either a six-unit surface or underground plant were incorporated into the design and construction of the right abutment of the dam (Fig. 2). Prior to 1971 alternative 2500 MW capacity surface and underground powerplant arrangements were studied. Cost estimates for the two alternatives were the same within the limits of estimating procedures. However, it was believed there was a certain continuing risk in locating a surface plant at the toe of a steep canyon wall. Therefore, in 1971 a tentative decision was made to proceed with an underground plant, provided that additional exploration confirmed assumptions of

Jan 1, 1976

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

"INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of the city of Timmins, Ontario. Two types of ore are treated; 'A' type, a copper-zinc-low silver ore producing copper and zinc concentrates, and 'C' type, a copper-lead-zinc-high silver ore producing copper, lead and zinc concentrates.The ore is processed at a combined rate of 12,400 metric tonnes per day through four parallel grinding and flotation divisions. Three divisions treat the 'A' type ore and the fourth treats the 'C' ore. Each division is fed from its own fine ore bin.This paper reviews the grinding section with specific emphasis on grinding media consumption and the factors affecting it as related to 'A' type ore. At Kidd Creek there was an awareness that grinding media consumption varied on a weekly and monthly basis. The reasons for this variation was usually attributed to ore hardness as evidenced by short term variations in the circuit feedrate and head assays. However, there has been a diversity of opinion published in recent years regarding the factors contributing to steel consumption. This initiated a study of historical Kidd Creek operating data, from the period 1970 to 1986 inclusive, to determine the effect of various operating parameters on media consumption. The results of the study could then be used as a baseline for future media consumption testwork."

Jan 1, 1988

By Ken Witherly

Modern airborne EM surveys typically acquire more data than is processed or analyzed at the time of acquisition Suitable additional processing can provide more diagnostic information, thereby allowing for more effective ranking and hopefully, follow-up of outcomes

Apr 1, 2005

By Daniel Hauer

Blocking. (5) The “blocking” of boulders is a much cheaper way of breaking them up than “mud capping.” It should always be used in preference to that method except when too much time will be consumed by a crew of men waiting for the drilling to be done, as shown in example of cost No. 1, as given under “mud capping.” Under such circumstances the time consumed would be a greater cost to the contractor than the extra amount of dynamite. Then, too, on large thin boulders to drill one hole would result only in breaking the stone into such pieces as would again have to be broken; and the many holes might equal the cost of extra dynamite. Under such circumstances if method (6) cannot be used, “mud capping” will have to be resorted to, to do the work economically.

Jan 1, 2006

By George Carlos dos Santos Anselmo

O efeito de memória de forma tem como principal objetivo a recuperação da forma por meio de aquecimento acima das temperaturas críticas de transformação. Fitas das ligas Ti50Ni46Cu4 e Ti50Ni44Cu6 (% at) foram preparadas através do processo melt spinnig com velocidade da roda de 38 m/s e 50 m/s. A caracterização das fitas foi feita por Calorimetria Diferencial de Varredura (DSC) e Microscopia Eletrônica de Varredura (MEV). Foi observado que com o aumento da velocidade de rotação da roda de 38 para 50 m/s um refino de grão foi observado e as temperaturas de transformação diminuíram chegando à variação de aproximadamente 7°C. A solidificação rápida produz defeitos na estrutura da liga e, consequentemente, uma maior dificuldade de ocorrer as transformações de fase, bem como produz um refino de grão.

Aug 16, 2017

The objective of current efforts by AQUILA Mining Systems Ltd. is the continued development of computer-based systems and techniques to automatically process and interpret monitored performance data from surface blasthole drills and mining shovels, and the management and coordination of these pieces of equipment by GPS (Global Positioning Systems).

Jan 1, 1995

By Todd Clarke, Ralf Winterberg

For more than a decade the tunneling industry has explored the potential and benefits of macro synthetic fiber (MSF) reinforced concrete solutions for precast tunnel segments. Parallel to industry investigations, academic research is being undertaken to better understand this material when subjected to the typical loads expected during mechanized tunneling. This paper investigates the performance of MSF reinforced precast concrete tunnel segments by means of an experimental program comprising testing of full-scale tunnel segments. The presentation of the satisfactory results of the experimental testing regime will be complemented by a brief case history from a successfully executed project—an America’s First.

Jun 13, 2021

By Hubert E. Risser

Although, for about a half-century the percentage of coal production provided through strip mining has steadily increased, recent trends indicate that a peak in percentage (not tonnage) is being approached, principally because of the decline in economic adrantage enjoyed by strip mining compared to underground mining. Factors contributing to the decline are the decrease in the margin of advantage in manpower requirements held by strip mining; an increase in depth and volume of overhurden, requiring larger equipment and capital investment; increasing lack of reserve land blocks large enough to support extensive strip mining operations; more stringent legislation for reclamation of stripped land, with increasingly higher costs of such reclamation; and the increasing costs of land surface rights for strip mining. Already there has been a peak and suhsequent decline in relative importance of strip mining insome major Eastern coal-producing states; trends indicate that a peaking for the whole Eastern region is on the way. Although, in the West the pressures are less severe, they will, nevertheless, reduce to an increasing degree the advantage that strip mining has possessed. For about half a century, strip mining has been providing an ever-increasing share of total coal output in the United States, and in the past 30 years this share has grown from less than 8% to 33.7%, as shown in Fig. 1. Fig. 1 also shows that strip mining is gaining faster in the West than in the East. From 1961 to 1967, output from strip mines grew 63.6 million toqs, or 52.2%. Certainly there is nothing in such performance to indicate any peaking in the level of strip coal-mine production. But the fact is that, if not in actual tonnage, strip mining appears to be reaching its peak in relative importance, at least east of the Mississippi River. And the area east of the Mississippi provides 90.0% of the strip and 94.9% of the total coal production of the nation. The relative economic advantage which spurred strip mining's growth for a third of a century has been diminishing markedly in recent years. Fig. 2 shows evidence of this decline. From 1947 until 1961, strip tonnage output remained fairly stable, at the end of the period showing only a 12.5% decline. Meanwhile, underground coal production fell 44.5%. As the result of the greater decline in underground coal, strip coal in 1961 furnished 30.3% of the total coal produced, compared to only 22.1% in 1947. In the succeeding six years, however, underground coal output increased by 76.5 million tons, while strip output increased only 63.6 million. Further evidence of the strengthening of underground coal's relative position — or if you will, the weakening of strip coal's position — can be found in the major coal stripping states: Illinois, West Kentucky, Ohio, Pennsylvania, Indiana, and West Virginia, which in 1966 provided 80% of the nation's strip coal. Fig. 3 shows what has been happening in three states lying in the Appalachian field and in the total output of these three states. In the figure, the column height represents the output of coal mined by all methods. The number at the base of each column is the percentage mined by stripping. In Pennsylvania and Ohio, the percentage of strip mining increased between 1956 and 1961, but by 1966 had declined from the 1961 level. In West Virginia, a decline occurred during the first five years but was followed by a rise. In January 1968, Coal Age published an article listing the locations and capacities of new large mines in the planning and construction stages that would be operating by 1968-1971. The plans for West Virginia and Pennsylvania indicated all the new mines would be underground. Except to the extent they might replace existing under-

Jan 1, 1970

By T. Frömmer, H. Wagner

An inter-disciplinary geotechnical study has been carried out in an Austrian magnesite mine. The paper describes the how geological data, in situ and laboratory tests as well as subjective, empirical, geophysical and numerical methods have been used to identify critical areas in the mine. In einem österreichischen Magnesit Bergbau wurde in den letzten Jahren eine interdisziplinäre geotechnische Studie durchgeführt. Der Vortrag beschreibt den Einsatz subjektiver, empirischer, geophysikalischer und numerischer Methoden zur Identifikation geotechnischer Problembereiche Ces dernières années des études géotechniques interdisciplinaires sont effectuées dans une mine souterraine de magnésite en Autriche. Ce rapport trace l’application des méthodes subjectives, empiriques, géophysiques et numériques pour identifier les zones problématiques dans la mine

Jan 1, 2003

By Ron Board

"Probably the only thing that can he said about conveyor belt scales without fear of contradiction is that they have been responsible for as much or more puzzlement, argument and frustration than almost any other piece of equipment commonly found in ore processing facilities. To be sure, there are certainly a good number of satisfactory installations, some of these having been achieved through forethought and careful consideration in the early stages of plant design, while others seem to owl their success to what seems to be little more than good luck or white witchcraft; and it might also appear that black witchcraft or other gremlins are solely responsible for the poor performance of many belt scales that enjoy well-designed installations with apparently good operating conditions.This paper is intended to acquaint users with the major operational reasons why belt scales seem so fickle (and downright ornery too), and establish some reasonably simple test standards against which the performance of scale hardware can be measured. Then it shall be shown how the design flexibility of electronic scale systems can offer particular advantages in overcoming some of these everyday problems in a practical way, and without undue inconvenience to plant operations."

Jan 1, 1975

By C. H. Johnson

This paper on the out-and-fill method of mining is one of a series on mining methods published by the United States Bureau of Mines. It has been compiled chiefly from recent publications of the bureau describing in detail mining methods and costs at various mines. Other sources of information were the technical press, the Transactions of the American Institute of Mining and Metallurgical Engineers, the Mines Haudbook, and company reports. References other than those mentioned in Table 1, which lists the mines entering into this discussion and gives general data regarding them, are given in the body of the paper. The authors wish to acknowledge the kind assistance of many operating officials, either through correspondence or in the course of numerous visits to their mines. DEFINITION OF CUT-AND-FILL STOPING The out-and-fill method of stoping is that method in which relatively small sections or slices are taken successively from the lower surface of a block of ground by open-stoping methods, the broken ore being removed and each section filled with waste material before the next is mined. This definition excludes shrinkage stoping, even with subsequent filling; it excludes square-set and fill methods; it excludes the Mitchell slice method, which may be classed as underhand square-setting; it excludes the systematic use of stull sets and filling, which is a variation of square-setting; it excludes any method involving the caving of the ore, walls, or overburden during the process of extraction, although caving may be allowed to take place when the waste fill is withdrawn for use in other stopes; and it excludes any open-stope method without filling. Through variations, which will be discussed later, the cut-and-fill method merges into shrinkage stoping, open stoping, or square-setting. The use of casual timber support, such as props, stulls, or timber cribs for holding up weak portions of the back does not constitute a change from cut-and-fill to square-set mining.

Jan 1, 1933

By Deepak Vidyarthi

This paper deals with various measures adopted in protecting a conveyor duct (named after a Conveyor Belt that was numbered as ‘02’) housing a 1600 mm (63 inches) belt conveyor system in a large, heavily mechanized open cast iron ore mine, producing about 20.0 million tones of ore per annum.

Jan 1, 2008

By Steve Kral

A few months ago, Congress passed, and President Bush signed, a national energy bill. Designed to decrease the nation’s dependence on foreign sources of energy, the bill earmarked several billion dollars to increase the use of U.S. coal reserves. The bill also modified permitting regulations to speed up development of the coal reserves located on federal land. Coal currently supplies more than half of the nation’s electricity needs. And as housing starts continue to in-crease and with the nation’s appetite for electronic gadgetry, the demand for energy in the United States will only go up. That means coal producers must expand production while at the same time containing costs so they can enjoy this period of improved coal prices.

Jan 1, 2005

By F. P. Haver

The Federal Bureau of Mines developed a 10,000-ampere cell to determine the economic feasibility of producing high-purity electrolytic titanium from mill scrap or offgrade sponge. Operating variables were investigated, matetial handling procedures were established, and the cost of electrorefining titanium was determined. The prototype cell produced premium-grade metal (<100 Brinell hardness number (B.h.n.)) from very impure Kroll sponge at a processing cost of less than $0.60 per pound. Refined metal was deposited at the cathode in the form of coarse (85 percent plus 34-mesh), hexagonal crystals of a titanium when the cell was operated an 850° C. A cathode current density of 1,000 amperes per square foot and a molten sodium chloride electrolyte containing approximately 5 percent by weight of soluble titanium were used. In continuous operation, at the optimum number of ampere-hours, (40,000), the current efficiency averaged slightly less than 60 percent. It was possible to supply large enough amounts of electric current for electrolysis to maintain the temperature of the bath, thus reducing overall power consumption to less than 5 kilowatt-hours per pound of metal refined.

Jan 1, 1961

By Theodore L. Turner

This Bureau of Mines report describes calcination of kaolinitic clay in a direct-fired 2-1/2- by 24-ft rotary kiln at 750° and 775° C. Methods for preparing kaolin feed materials and characterization of calcined products are discussed. Approximately 99 pct of the alumina in a typical eastern Georgia kaolin was soluble in HC1 after calcination at either 750° or 775° C.

Jan 1, 1982

By Pengfu Tan

The control of converter slag chemistry and slag viscosity has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been used to predict the chemistry and viscosity of converter slag. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on slag viscosity, liquidus temperature of converter slag and skimming operation has been discussed. Some applications of the industrial operations have been presented.

Jan 1, 2006

By B. Y. Park

This paper develops a series of three-dimensional simulations for the Bayou Choctaw Strategic Petroleum Reserve. The U.S. Department of Energy plans to leach two new caverns and convert of one of the existing caverns within the Bayou Choctaw salt dome to expand its petroleum reserve storage capacity. An existing finite element mesh from previous analyses is modified by adding two caverns and increasing the size of existing Cavern 102. The structural integrity of the three expansion caverns and the interaction between all the caverns in the dome are investigated. The impacts of the expansion on underground creep closure, surface subsidence, infrastructure stability, and well integrity are quantified. The results show that from a structural viewpoint, the locations of the two newly proposed expansion caverns are acceptable, and all three expansion caverns can be safely constructed and operated.

May 1, 2009

By Sunil Koppalkar, A. R. Laplante

"A Pilot Plant was installed in one of the grinding circuits of the Dome Mill, Ontario, Canada. Tests were conducted on a KCCD12 Knelson Concentrator to systematically analyze the effect of operating variables on the performance. The main objective of this test work was to explore the effect of very coarse (6 mm) feed size on GRG recovery and performance of the Knelson concentrator. Preliminary results have shown that coarse feed size is deleterious to maximizing recovery. Size-by-size GRG recoveries have shown an unusual trend in the sense that recoveries do not decrease monotonically with decreasing gold particle size. Similar trend observed in one other full-scale unit has been compared. The observed trend is probably linked to the feed size distribution and top size.INTRODUCTIONKnelson Concentrators are the most widely used semi-continues centrifuge gravity separation units for the recovery of gold and platinum group minerals (Xiao and Laplante 2004). The main advantages over the competing centrifugal gravity units are their design, operating simplicity and good separation efficiency that make them the most common choice for gravity circuit. Despite some characterization at bench scale and a limited characterization at full scale, there is a lack of a comprehensive study of impact of operating variables on efficiency that reflects realistic full scale operating practice. GRG characterization studies, at bench scale, on these units provide information about the occurrence of gold in ore samples but fail to provide adequate information about the effect of operating variables for full-scale units. It is well known fact that such work is difficult to undertake on full-scale units owing to the difficulties involved in sampling and systematic variation of operating parameters. To tackle these problems, a pilot facility consisting of a 12-in CD Knelson Concentrator, a feed screen and tailing pump was installed in one of the grinding circuits of Dome Mill. This paper describes the work carried out and the results.Porcupine Joint Venture (PJV)Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. The JV utilizes the milling capacity of the Dome Mill to process ore from Placer Dome and Kinross mines. The Dome Mill circuit has gravity concentration, cyanidation and CIP circuits to recover gold. Gravity recovery has been used at Dome Mill since inception to recover gold: first by using conventional jigs, which were eventually replaced by two Knelson Concentrators in 1993, one in each of the grinding circuits. Three more Knelsons joined the circuit in 2002 to improve gravity recovery. An Acacia Intensive Leach Reactor was also added in 2002 to process gold concentrates replacing shaking tables (Chong et al 2004)."

Jan 1, 2007