Search Documents

By Rajagopala Reddy Kallu

After the Sago and Darby No. 1 mine incidents, the new regulatory standards for the design of mine seals in underground coal mines of the United States require the mine seals to withstand higher explosion standards. This necessitated for the development of new design approaches and standards. For development of any new design standards or approaches a detailed understanding of effect of key influencing parameters on the stability of mine seal is a must. This paper attempts to address one of the factors, i.e. roof convergence, that play an important role in the stability of mine seal under explosion loading. Initially a couple of three dimensional numerical models were built and tested for different levels of roof convergence. These models confirmed that roof convergence has great influence on seal stability. A detailed study is undertaken, with some simple assumptions, to establish typical influence of roof convergence on the stability of mine seal under different levels of static explosion pressures. Three dimensional distinct element code 3DEC is used for this purpose.

Jan 1, 2007

By C. Jay Hodgson

Hydrothermal systems form on land where and when an impermeable cap-rock unit ( either natural or self-sealed) , a permeable aquifer. and permeable discharge and recharge channels (cross-stratal permeability) develop in an anomalously hot part of the crust. A consideration of the relationship between magmatic and tectonic events in volcanically active areas indicates these conditions arise during: (1) the resurgent doming stage of the resurgent caldera cycle; (2) following movement on the bounding faults of tilted fault blocks ; and (3) as a result of hydrothermal boring associated with the intrusion of major sills. On the assumption that the submarine hydrothermal systems which deposit volcanogenic massive sulphide ores are comparable to subaerial hydrothermal systems, it is suggested that: (1) the horizon of mineralization corresponds to the time period when conditions favour the development of hydrothermal systems, as outlined above; (2) exploration for Cu-rich Cu-Zn-Pb or Cu-Zn ores should be directed to paletopographically high areas near discharge conduits , whereas exploration for Cu-poor ZnPb ores should concentrate on paleotopographically low areas down slope from conduits; (3) deposits with stringer zones lying above normally permeable units may be underlain by regionally extensive weakly mineralized and altered zones (self-seal caps) ; (4.) in the absence of a self -sealed cap, the ore horizon may be underlain by a naturally impermeable unit (e .g. a fine clastic sediment) ; (5) the condition of cross-stratal permeability may be evidenced by features such as dykes. alignment of vari ous magmatic and hydrothermal phenomena, abrupt thickness changes in stratiform units indicative of ponding against syn-volcanic faults, and fault-scarp slump deposits; (6) the condition of high heat flow may be evidenced by near-surface magmatism and steep thermal gradients preserved in metamorphic mineral assemblages.

Jan 1, 1977

By César Beraun, Pablo Espinoza, Luis Loaiza

En la unidad Cerro de Pasco de Empresa Administradora Cerro SAC, existen varias fuentes de aguas ácidas de diversas características, con diferentes rangos de acidez y contenidos metálicos de hierro, zinc y cobre, que parcialmente han pasado de ser un pasivo, en términos económicos y ambientales, a ser una fuente de recursos. El tratamiento convencional que se aplicaba en la planta de neutralización consistía en neutralizar la acidez protónica y precipitar los metales disueltos utilizando lechada de cal y luego separar por sedimentación los sólidos formados para obtener un efluente tratado descargado por vertimiento y disposición de lodos formados en la relavera de la unidad. El cambio de pasivo a recurso para las aguas ácidas pasó por rehabilitar un proceso abandonado, identificando y separando en el interior de la mina subterránea un flujo que por su contenido de cobre ha sido separado en un circuito independiente del existente para las otras aguas ácidas de menores contenidos metálicos. Se desarrolló una secuencia de procesos de precipitación selectiva; inicialmente para recuperar cobre se implementó a escala industrial la cementación con chatarra de hierro. A escala piloto se han concluido tanto las pruebas para separar el hierro por oxidación y precipitación selectiva en medio ácido, como aquellas por las que, a partir de la solución pobre de la precipitación del hierro, se precipita el zinc en dos alternativas: precipitación alcalina como hidróxido de zinc o precipitación en medio ácido por sulfuración. A escala industrial, la recuperación de cobre en la cementación con chatarra de hierro alcanza el 75%, y 85% de contenido de cobre fino. A escala piloto, para el hierro se espera una recuperación sobre 95%, para un producto que alcanza 39% de fierro, mientras que para el zinc, la recuperación esperada es de 93% y un contenido de 35% de Zn en el precipitado de sulfuro.

Sep 20, 2019

By JOHN LANE DYNAN

HE Tonopah Extension property consisted originally of three claims, with an area of 38 acres. In 1902 a shaft, now known as No. 1, was started near the eastern end of the property, close to the Tonopah Mining Co.'s boundary line, in the. andesite cap rock' which covers the ore-bearing formations in the western end of the Tonopah district. A short distance below the 60-ft. level, the orebodies pinched out, although the veins continued. This shaft has not been used since 1916. Before 1910, the production was small, coming mostly from small shoots of high-grade shipping ore. In that : year, the, company started its 30-stamp mill and cyanide plant; the mill was later enlarged to 50 stamps, with a corresponding increase in the cyanide-plant capacity, which brought the capacity of the mill up to 350 .tons per day. The total production of the mine to Oct. 1, 1920, is 871,177 tons of ore, from which was recovered 15,267,216 oz. of silver and 156,241 oz. of gold.' This makes an average recovery per ton of 17.5 oz. silver and 0.179 oz. gold. The average price received for silver since' the beginning of operations is 65.87 c. per oz., and the average value recovered from the ore-'is $15.25. The area of the property has been gradually increased by purchases and consolidations of adjoining ground until it is now 647 acres. A new shaft, known as No. 2, was started in 1912, 1600 ft. west .of No. 1, and in the following year a crosscut on the 750-ft. level of this shaft resulted in the discovery of the. Murray Vein system, from which the greatest prosperity of the mine has come. This vein, with its related veins,

Jan 1, 1921

By K S. Smith

Mineral-deposit geology, geochemical processes, and biogeochemical processes are fundamental controls on the environmental conditions that exist naturally in mineralised areas prior to mining, and that result from mining and mineral processing. Input from economic geologists and geochemists is therefore crucial to effectively predict, assess, mitigate, and remediate the environmental effects of mineral-resource development. Recent open pit gold mining at Summitville, Colorado , has received intense public scrutiny for a variety of environmental problems, most important of which has been extreme acid drainage. Now a Superfund environmental cleanup site, Summitville exemplifies how economic geology and geochemistry principles: 1. could have been better utilized to first predict and minimise the environmental problems, and 2. can now be used to optimize the environmental cleanup.

Jan 1, 1995

By Dan Preston, Shane Yanagisawa, Robert Marshall, Don Deere

Geotechnical Baseline Reports often estimate the number of cobbles that will be encountered in terms of volume or weight. These estimates are practically impossible to verify in the field. ClaroVia Holdings in conjunction with Frontier Kemper Constructors Inc. developed Digital Geologist 2.0 to classify and count cobbles discharged from an EPB TBM at the RSC7 project in Burbank, CA. The system worked by using two stereoscopic laser sensors with a global shutter to scan and count cobbles at 12 frames per second. Results of the effort are revealed along with lessons learned and paths for improvement.

Jun 13, 2023

By A. P. I. Popoola

Laser coatings are used for a wide variety of applications. TiB2/Ni intermetallic matrix composite coatings were fabricated on Al-substrate by a high power Rofin Sinar Nd: YAG solid-state laser. The characterization of the coatings was carried out by optical microscopy (OM), scanning electron microscopy (SEM/EDS) and X-ray Diffraction (XRD). Electrochemical study of the laser coatings in 3.65 per cent NaCl at room temperature revealed that with very high weight proportion of nickel the corrosion resistance of the coatings deteriorated due the presence of AlB10 phase. 50 wt per cent TiB2+50 wt per cent Ni laser coatings exhibited the highest corrosion resistance in test solution. Keywords Corrosion, protective film, laser surface alloying, reinforcement.

Jan 1, 2011

By S M. Loewen, J J. Fuykschot

Located in the north-west of Kazakhstan is a world-class podiform chromite deposit. Donskoy mining and beneficiation complex (DGOK), a branch of Kazchrome TNC, which is a subsidiary of the Eurasian Resources Group (ERG) operates two underground mines in this area, one of which is the ‘10th Anniversary of Kazakhstan Independence’ (DNK) mine.The mine currently applies the gravity caving mining method, producing 1.8 Mt/a of ore utilising a slusher layout and rail transport to the hoisting shafts. The deeper zones form the largest mineral resources at the DNK mine and are planned to be developed in the next several years. At this depth, the generally poor ground conditions, combined with the high in situ stress state will potentially lead to extremely challenging mining conditions.This paper describes a technical study undertaken by SRK to determine the possibility of increasing the maximum production rate from the currently envisaged 6.0 Mt/a to 7.2 Mt/a, and to reduce the time taken to steady state production.Based on a newly created 3D model, the inclined caving method was proposed for the largest orebodies. This method, presently not implemented at any operating mine, although planned for two other projects, was deemed very suitable to deal with the weak rock mass characteristics and the plunging morphology of the mineralisation.Dassault Systèmes’ GEOVIA’s Footprint Finder software (a module of GEOVIA’s PCBC™) was used to determine the caving zones and production schedules. The total mine design was completed in Deswik software, and resulting schedules combined in Excel.In addition to the use of an inclined caving method, several other suggestions were made to increase the productivity of the mine, such as the application of a conveyor belt system transporting multiple material types, teleremote technologies and the application of thin sprayed liners to reduce the swelling of the rock mass.CITATION:Fuykschot, J J and Loewen, S M, 2016. Inclined caving option for the DNK mine, Kazakhstan, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 669–682 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By F. D. Wang

This report presents a structural-mesh-generating computer program for the two-dimensional finite-clement method of mine structural analysis of single and multiple openings in nonhomogeneous rock mass. This program greatly reduces the amount of input data required and the chances of error which otherwise are large owing to the large amounts of data and the complex mesh involved. The program description, a user's guide, example problems, and program listing are included.

Jan 1, 1971

By Anthony J. Konya

"This paper was written during part of the author’s student co-op with Cargill Salt at its Avery Islandunderground salt mine in Louisiana. Blasting salt is a unique type of blasting that is different than blasting other rock types. The plastic nature of salt, along with its large swell factor make salt a challenge to blast. The Cargill salt mines use and have tested a variety of different methods for breaking salt in an efficient manner, however these blasting methods are rarely used in other operations nor talked about today."

Jan 1, 2016

The Effect of Molecular Weight on the Adsorption and Efficacy of Polysaccharide Depressants

Sep 13, 2010

By R. J. Lytle

INTRODUCTION Prior to excavation in soil and rock, it is useful to know the subsurface structure. This is important information both for safety and for equipment scheduling reasons. It is useful to know whether parts of the subsurface might be potentially troublesome or of different character than is generally thought present. By using geophysical probing, it is possible to infer the location and size of these unusual regions. The ground structure is commonly estimated from core samples taken from boreholes. These cores give a detailed knowledge of the structure in the borehole. However, knowledge of the structure exterior to the borehole can only be extrapolated from core data. By using seismic and electromagnetic cross-borehole geophysical probing, remote probing can be used to sense the region exterior to boreholes. A recent advance has significantly improved the state-of-the-art for defining the ground structure between boreholes. This new procedure utilizes large amounts of data and provides a detailed picture of the subsurface. The data processing algorithms used are similar to those in medical imaging of the human body using x-rays, a science called x-ray tomography. This imaging of the ground is called geotomography, which is a shortened acronym for geophysical tomography. Several examples of geotomography applied to imaging ground structure are presented. Our approach has been to probe the ground with electromagnetic and seismic waves. We map the region of interest with signals transmitted between multiple source and receiver pairs lowered in boreholes on opposite sides of the region (Figure 1). The received signals vary according to the transmission properties of the media

Jan 1, 1979

By James L. Vinson

Wilbur Smith Associates (WSA) has provided planning, engineering and construction oversight assistance to the Tennessee Department of Transportation (TDOT) for three construction projects intended to widen and improve segments of I-40 and associated interchanges in Knoxville, Tennessee. The projects are within the karst terrain of the Valley and Ridge Province. Subsurface conditions are characterized by an irregular rock surface coupled with differential weathering. Because of the projects? impact to local and interstate motorists, consideration was given to innovative planning, materials and construction practices that could accelerate construction. Two innovative deep foundation measures included rock-socketed pipe piles, which act as both foundations and substructure elements for a bridge?s interior bents, and the first widespread use of rock-socketed drilled shafts as bridge foundations on a TDOT project. The pipe piles were used at a site with significant cavities within the limestone bedrock. This resulted in design verification and constructability difficulties that required delays, but measures were ultimately employed to produce a sound foundation system. Over 110 drilled shafts have been constructed at sites with generally low solution activity. Relative to H-pile footings, which were included as an alternate foundation, they have apparently allowed accelerated construction at a competitive cost.

Jan 1, 2006

Control of flotation processes is mostly managed by plant operators, who assess the performance of the plant based on their own experience and other heuristic rules. These rules tend to be subjective or ill-defined, since most of them are concerned with the structure of the flotation froth, such as colour, bubble size and shape distributions, froth mobility and froth stability. These phenomena are very difficult to quantify objectively, and inexperience on the part of the operators, human error, etc., can lead to significant inefficiencies in plant operation. In this paper the development of a fuzzy system to support the control decisions of plant operators is described, which leads to significantly smoother control action and more stable plant operation than could be obtained with crisp sets of rules or manual control strategies. Keywords: flotation, fuzzy logic, image analysis, genetic algorithms, rule induction

Jan 1, 2000

By Cary Hirner, David Stacey, William A. Rochford

Design considerations and construction techniques were implemented to address groundwater infiltration from a confined aquifer during the excavation and lining of the Cady Marsh Flood Relief Tunnel. This 3-m finished diameter, 2-km long tunnel was successfully completed cost-effectively in an urban setting near East Chicago, Indiana. The soft ground was mined using a conventional tunnel boring machine with hydraulically actuated flood doors and supported with steel ribs and timber lagging. The tunnel was lined with cast-in-place concrete. Dewatering was implemented in settlement prone, boulder-laden ground in residential neighborhoods during construction to depressurize and partially dewater the aquifer at the tunnel horizon. This paper describes the design decisions and construction methods utilized to mitigate and limit infiltration into the tunnel during construction and operation, as well as manage ground settlement.

Jan 1, 2007

By Stone. Jon P.

INTRODUCTION Countries that are currently developing their mineral potential have unique information systems requirements to support these activities. The mining laws usually grant the State considerable authority over the process. In many instances, the mining laws give a government agency the responsibility for granting and controlling exploration permits and development concessions. This is the case in Costa Rica. The Direcion of Geologia, Minas, y Hidrocarburos (DGMH) of the Ministerio de Industria, Energia y Minas (MIEM) is responsible for the management and operation of the National Mining Register. This paper describes the results of two studies of the information system requirements to support the National Mining Registry as well as those supporting some of the other function of the DGMH. The first of the studies reviewed the situation before the installation of computer equipment. The second study evaluated the installed systems. BACKGROUND Historical Perspective Mining in Costa Rica is at present a relatively minor part of the economy. It consists primarily of industrial minerals and gold production. Gold production is largely by small-scale miners and may be more substantial than reported. There is considerable interest on the part of the Government in both having a better understanding of the existing mining industry and promoting future development. Mining law was first provided by the Ordinanza de Mineral (of 1830). This was replaced by the first Mining Code of 1953. Apparently, one of the first problems caused by the 1953 law was the granting of concessions which were not worked. A 1968 agreement with ALCOA also resulted in political conflict. The Government worked on a new Mining Code for many years and in 1982 the current Mining Code was enacted. Draft implementing regulations were prepared in April 1984. Mining Code of 1982 The Mining Code of 1982 addresses most aspects of mining in Costa Rica including the declaration that all mineral resources are to be the property of the State. The State may grant exploration permits and exploitation permits. The exploitation of hydrocarbons, radioactive minerals and certain water resources was reserved to the state. The DGMH was given authority to settle placer claim disputes, maintain a registry of exploration permits, and exploitation concessions. and generally supervise mining activity. Towards this, the Mining Code of 1982 includes rather detailed requirements for the processing of application for permits and concessions. Mining Code Application Requirements The following briefly describes the requirements to give the reader a feeling for the complexity of the process. Currently, over 1,000 active applications, exploration permits and exploitation concessions are being monitored under the process. The number remains relatively consistent in that the number of new applications is usually about the same as the applications that are put aside. The time and date of the filing must be certified by the DGMH. The application must include all the information specified in the Mining Code. If incomplete, DGMH must notify the applicant of the deficiencies or omissions and direct that the applicant correct the deficiencies or omissions within 8 business days (a single 30 business-day extension is allowable). If the applicant does not respond as directed, the application is deemed as not having been filed and the pertinent information is placed in the files. The DGMH must reject the application outright and direct it be placed in the files in the following cases: (a). If the new application covers the area of a previous permit or concession, either being processed or already granted.

Jan 1, 1987

By A. Kale

A chlorination pilot plant having capacity to produce 5?10 kg/hr of titanium tetrachloride is in operation at the chlorination facility in Mintek. The bubbling fluid bed chlorination plant can be operated in batch and/or continuous process to study the chlorination kinetics of various feedstocks. The chlorination of titaniferrous ores to produce titanium tetrachloride (TiCl4) was carried out during the commissioning of the pilot plant and also as part of the titanium programme carried out at Mintek. TiCl4 is a basic raw material for producing commercial titanium dioxide pigment and titanium metal. This paper discusses the challenges faced during the commissioning and operation of the chlorination pilot plant. It also discusses the effect on the auxiliary facilities and instrumentation as a result of the harsh operating conditions of +1000°C and use of corrosive gases like chlorine and titanium tetrachloride. It discusses the effect of physico-chemical properties of the titanium tetrachloride and iron chlorides. The effect on the chlorinator refractory lining due to heating and cooling of the chlorinator is also discussed. Besides the special provisions made during the design of the chlorinator, this paper also discusses the operational experience and possible solutions to be implemented in future. Keywords Fluid bed chlorination, titanium ore chlorination, titanium tetrachloride (TiCl4) production using fluid bed technology.

Jan 1, 2011

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

Ontario Operaations Mining Garson Stobie Copper Cliff North Copper Cliff South Creighton Mcreedy East Milling Clarabelle Mill Smelting Smelter Matte Processing Anode Casting Refining Copper Cliff Nickel Refinery Port Colborne Cobalt Refinery

May 1, 2007

By M. W. Lewis

A mine's inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine ’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004