Search Documents

By Christopher Gammons

In developing countries throughout the world, gold ores are being processed by mercury amal-gamation, a technique long banned in the U.S. - unless a retort operation is used for mercury recovery - due to mercury toxicity and its effects on the environment. Amalgamation is a simple process that involves contacting a ground, slurried concentrate or ore with mercury in a slightly agitated vessel, usually for several hours, The amalgamated mercury is separated by gravity and then filtered through a fine cloth to collect the gold amalgam as a sponge, which is then fired to remove the final remnants of mercury and produce high quality gold. However, in Peru and other developing countries in South America and throughout the world, tailings are simply discarded into uncontrolled drainages and ponds and the sponge is fired in the open air. Clearly, in this case, environmental friendly and, to make matters worse, is typically conducted by family members of all ages without proper protection. Furthermore, the technique is inefficient, yielding approximately 50% gold recovery. For the past two years, faculty members from Montana Tech in Butte, MT, USA and the Universidad Nactonal del Altiplano in Puno, Peru have teamed to study the La Rinconada Mine Complex located in southern Peru approximately 100 kilometers north of Lake Titicaca and 25 kilometers west of Bolivia. The mining complex is over 5,000 meters above sea level and exists at the foot of a receding glacier in the Andes Mountains. A suite of soil and water samples collected in 2001 documented extensive Hg contamination in the Rinconada area [1]. The present paper summa¬rizes a follow-up investigation in July-2002, in which water samples were collected at numerous locations along the 200 km length of the Rio Ramis, from the Rinconada mine com¬plex to Lake Titicaca, In addition, we report new results of Hg analyses of fish from Lake Titi¬caca, The results of this study have relevance to safety and health concerns for the miners as well as people in downstream communities.

Jan 1, 2003

By E. Fregeau-Wu

The mineralogy and grain size distribution of phases in a steelmaking slag and experimental products from the heating of the slag under various conditions were determined to explore the possibility of recycling of the iron and manganese to the blast furnace. The steelmaking slags consisted of three major phases: dicalcium silicate, dicalcium ferrite, and Mg-Mn-wustite. Most of the phosphorus was contained in the dicalcium silicate and to lesser extent in the dicalcium ferrite. Due to the fine grain size of the dicalcium silicate, grinding and magnetic separation required pretreatment to increase the grain size and hence the liberation. Experiments on a steelmaking slag were conducted by heating the slag to 1633-1748°K( and slow-cooling in an inert atmosphere at various rates with or without the addition of fluorspar (CaF2) as a flux. Grain size distribution analyses of the starting material and the slow-cooled products were performed using the SEM-IPP area scan method and the QEM*SEM linear scan method. Comparable and reproducible results were obtained on the same sample using both methods. A size versus volume percent plot showed the increased grain growth most effectively. Examples of the grain size distributions obtained were used to show that a higher soaking temperature prior to slow-cooling, a slower cooling rate, and the addition of fluorspar to the slag promoted grain growth.

Jan 1, 1989

By Gus Van Weert

Solvent extraction of iron from zinc refinery liquors has been investigated before, mainly on the MEHPA / HC1 stripping combination. Leakage of chloride into the zinc electrolyte and the costs of handling the ferric chloride eluate have prevented this option from being adopted. This work explores the stripping of the ferric loaded organic phase with nitric acid to take advantage of the possibility of regenerating up to 6N nitric acid, and clean spheroidal hematite production by autoclave treatment of ferric nitrate solution. The work was carried out with DEHPA (di 2-ethyl-hexyl phosphoric acid) in kerosine. Degradation testing proved the DEHPA to be very stable, when exposed to nitric acid solutions up to 6N and temperatures up to 70" C over a period of five days. Ferric iron was removed completely froma synthetic hot acid leach liquor, irrespective of the DEHPA concentration. Stripping the ferric turned out to be the problematic step. Although the stripping efficiency was considerable better at 50 than at 20° C, it decreased with increasing DEHPA/Fe ration in the organic phase. Eluates of no more than 5-10 g/l ferric nitrate were produced. surprisingly, nitric acid was found to be a less efficient stripping agent than sulphuric at equivalent normality and its efficacy levelled off above 4N. It was concluded that DEHPA does not appear to be the S.X. reagent to take advantage of the low cost autoclave decomposition of ferric nitrate opportunity in zinc hydrometallurgy and that another S.X. reagent, also resistant to nitric acid, but based on weaker compound formation is needed.

Jan 1, 1998

By J. R. Donald

Surface and interfacial phenomena play a significant role in refractory performance. For example, the wettability of the refractory material with slag, matte, and metal influences infiltration and interfacial reactions. Yet, very little fundamental information regarding the surface properties of refractory materials and slag is available. Thus, in the present work, the sessile drop technique incorporating a high temperature furnace equipped with X-ray fluorescope was employed to investigate the surface and interfacial phenomena of fayalite-type slags on solid alumina at 1200?C. The iron to silica (Fe/SiO,) ratios employed were 1.4 and 2.0, and the oxygen potentials used were log p02 =-11 and log p02=-9 atmospheres. The contact angle between the fayalite-type slags and the alumina were determined to be relatively low, at about 16.9 to 19.6 degrees under the experimental conditions. The surface tension of fayalite slag (Fe/SiO2=1.4) at an oxygen potential of log -11 was 0.298, which agreed with the work of previous researchers. The surface tension of the fayalite was observed to increase with time. The spinel FeAl2O4. was determined to be the product of the interfacial reaction, and 8.8 to 15.8 mass percent alumina was dissolved into the slag after 40 minutes.

Jan 1, 1996

By Gopalakrishna M. Rao

"Several industrial and government laboratories are of the opinion that solar--cell technology will grow into a billion-dollar industry by the year 2000, especially if oil prices rise again. Of the variety of materials that have been investigated as the major component of photovoltaic systems, silicon appears to have an outstanding advantage. The cost factor is the primary importance in photovoltaic development, since the technology to make silicon cells of acceptable efficiency and life time has existed since the early stage of the space program. Electrometallurgy is one of the low--cost processes for the production of silicon, since it allows direct, single-stage production from some abundant, inexpensive source materials such as silica and fluorosilicates. Among several systems, two are given particular attention, using inorganic baths with Si0 2 or K2SiF6 as the source of silicon respectively. They appear capable of development to commercial production. Conceptual designs of a commercial--scale cell for silicon production at temperatures above its melting point, and of a pilot' plant for plating silicon from an all-fluoride bath are presented. Energy ProspectsThe major changes in the world energy since the first energy crisis in 1970 have impacted on our community. When oil was $40 a barrel in the mid-1970s, we became obsessed with the energy conservation and a search for alternate energies. Even though the crude oil fell below $15 a barrel during the last several years, our energy security fears continue to haunt us. This time it is not the scarcity, but the abundance of foreign oil and the decline in the domestic production.The prospects of energy depends on the demand and supply of energy. These, in turn, depend on future energy prices, which are linked to economic factors, political events, and unforeseen circumstances. Although no one can predict the future with certainty, three energy consumption patterns used by the Ford Foundation are as shown in Fig. 1."

Jan 1, 1988

By Jim Sarvinis, Rory Hynes, Elizabet Cruz, Kerry McKenna, Maytinee Vatanakul

"Energy efficiency improvements achieved using heat recovery processes offer benefits to both the business case and environmental impact of metallurgical facilities. Global demand drives the development of lower and lower grade ore bodies. This trend results in higher energy intensity and consequently increased waste heat. Waste heat boilers and Organic Rankine Cycle (ORC) processes are becoming cost competitive methods of utilizing this waste heat.This study analyzes heat recovery from available sources to produce power using, • High grade: waste heat boiler and steam turbine generator. This system will produce electricity, and/or process steam.• Low grade: ORC to produce electricity. The cycle is well adapted to low- moderate temperature heat sources.Processes used in metallurgical plants, such as hot exhaust streams, cooling and condensers could benefit from application of these systems.The study demonstrates:• The energy and cost saving potential of waste heat recovery technologies,• The environmental benefit.IntroductionIn recent decades, process intensification has resulted in increased productivity from unit operations such as kilns, fluidized bed reactors and smelting furnaces and decreased unit operating costs. In the coming decades, the industry’s challenge will be to continue this trend while at the same time decreasing the consumption of fossil fuels and further reducing the environmental impact of its processes.The U.S. Department of Energy reports that available waste heat sources in industry, which is approximately seven quadrillion BTU (~7,400 PJ/y), exceeds the current production of all renewable power sources combined. In Canada there are about 2,300 PJ/y of available waste heat, with the pulp and paper, metallurgy, chemical/petrochemical and oil refining industries the main players. Natural Resources Canada (NRCan)9 has estimated that about 25% of that heat could be recoverable using existing technologies, which in turn, represents a reduction of 27 Mt/y of Green House Gas (GHG) emissions, plus considerable water savings due to lower water cooling requirements and less fossil fuel consumption."

Jan 1, 2011

By Jan A. Aune

The paper describes a number of electric furnace equipment modules especially developed or modified for slag furnace applications. Both the resulting design concept for a modern electric sulfide smelter and some of the changes in traditional process-concepts made possible are outlined.

Jan 1, 1983

By Nickolas J. Themelis

Nearly thirty two million tons of municipal solid wastes (MSW) are combusted annually in over one hundred U.S. Waste-to-Energy (WTE) power plants, thus reducing the use of fuel oil by about 1.6 billion gallons of fuel oil. One of the advanced WTE processes is the 0.9-million ton/y SEMASS facility at Rochester. Mass. Most of the combustion in the three giant combustion chambers occurs while the injected shredded wastes are in suspension, i.e .? in flash combustion mode. The velocity. temperature, and concentration profiles in the SEMASS combustion chamber were simulated by representing the combustible fraction of MSW by the simplified formula C6HIO04 and using the CFD program Fluent to solve the turbulent energy and mass transport equations. After validation against plant data. this model will be used to examine options for increasing the productivity of WTE combustion chambers, such as optimum distribution of primary and secondary air and oxygen enrichment.

Jan 1, 2003

By Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Jian-jun Hu

It could significantly increase the leaching rate of refractory gold concentrate containing sulfur and arsenic by roasting pretreatment with adding certain amount of sodium sulfate, and the mechanism of that was systematically researched with DSC, XRD and SEM in this paper. Results indicated that the mechanism of Na2SO4 on double refractory gold concentrate at roasting pretreatment can be summed up in the following three aspects：Firstly, Na2SO4 can react with SO2 and SO3 which is produced by the oxidation of sulfides and generate Na2S2O7(l), which plays buffer effect on sulfides exothermic oxidation, avoiding the secondary-encapsulated of gold. Secondly, the liquid phase of Na2S2O7 can cover mineral particles' surface that possesses a sintering effect, it leads to internal cracks of the particles. Finally, mineral particles will gather with sodium sulfate particles as the center that can improve the permeability of the layer.

Jan 1, 2015

By Jerold L. Johnson

Remediation of small-arms firing ranges is being investigated by the Naval Civil Engineering Laboratory and the U.S. Bureau of Mines. Scheduled closures of military installations, as well as the management of active ranges, require the development of methodologies for heavy metals removal to prevent their entering the surrounding environment. The impact berms contain high concentrations of metals, and the soil and vegetation surrounding the berms were found to have slightly elevated levels. The heavy metals characterized are in the form of whole bullets, a wide size distribution of free fragments, smeared lead on the surface of the soil grains, and very finely attached particles. Gravity beneficiation can remove liberated metal contamination effectively. Weak acetic acid leaching shows promise in lowering the final metal contamination to allow the ,soil to pass the Environmental Protection Agency's (EPA) Toxicity Characteristic Leaching Procedure (TCLP) criteria.

Jan 1, 1993

By Elias Rigopoulos

In the present study the reductive behavior of dust from the rotary kilns (RK), in ferronickel production from nickeliferous Greek laterites, is investigated. The study concerns dust of various origins (washing towers, electrostatic filters, polycyclones) and pellets made from the dust. Reducibility was studied in the temperature range of 700 °C to 850 °C in a laboratory tube furnace. Experimental results showed that reduction degree increases with temperature up to about 800 °C. The rate of reduction is great during the first minutes, giving a reduction degree R% equal to about 25%, in only a few minutes. After this, the rate is decreasing until it diminishes to zero after about 10-20 minutes of reaction. Maximum reduction degree achieved is 26 to 28%. Rates and reduction degrees at various temperatures are higher for the dust samples than those of the respective pellet samples. Keywords: Ferronickel, metallurgy, laterites, pellets, reduction

Jan 1, 2004

"In this paper, a mobile heat treatment furnace from Akkermans Gloeitechniek, a Dutch company, was simulated with Computational Fluid Dynamics (CFD). The furnace is cylindrical with four oil burners, and large metal products such as dredging pumps and impellers can be flexibly heat treated to obtain required microstructure and mechanical properties through stress relief, annealing, hardening and tempering. The furnaces are exposed to the open air, and thus the heat loss becomes significant and varies from day to day and from season to season. Since the temperature of the metal products to be heat treated can only be measured on the surface, the temperature evolution inside the metal could not be tracked in practice. CFD simulation provides a useful tool to predict the temperature evolution within the metal pieces and within the combustion space of the furnace. Energy distribution and heat loss can be subsequently estimated. An overall energy balance through temperature measurement indicted relatively low energy efficiency. Especially during the soaking period, the high energy supplied is barely used to compensate the heat loss of the furnace to maintain a constant temperature of the metal piece. The current CFD modeling aims to give advice on how to modify the design and optimize the operation to reach higher energy efficiency and low heat loss. The CFD model consists of turbulent combustion model, radiation model in participating media, and conjugate heat transfer between the combustion space and solid metal. Temperature measurement was carried out to provide thermal boundary conditions and overall energy balance of the operation. After the model validation with temperature measurement within the combustion space and metal surfaces, furnace optimization will be conducted.IntroductionHeat treatment is a common practice in metal production and manufacturing industries. Through heat treatment at certain temperatures with special patterns, unique mechanical properties of the metals and the metallic products could be obtained. ""Akkermans Gloeitechniek"" is a company situated in K.inderdijk, at location of LHC-Holland (www.ihccaland.com), the Netherlands. Heat treatment of metals is its core business. Various type of heat treatment are applied, such as stress relieving, soft annealing and hardening (quenching), tempering, transformation and precipitation. At the company 6 furnaces are in operation and the 7th is being built"

Jan 1, 2004

By Anupam Madhukar

The essence of an atomistic unified kinetic model of strained thin film growth and defect initiation is presented along with a comparison of its consequences obtained from computer simulations with experiments. Within the competing kinetics of a strain dependent activated incorporation of atoms and an asymmetry between upwards and downwards inter-layer migration, the model provides a consistent description of 2D versus 3D morphology evolution accompanied by the appearance of surface vacancies and steps at no energy cost. The correlated migration of these precursor defects offers an atomistic mechanism for the emergence of surface half-loops from the growth front (thus accounting for configurational and thermal entropy) governed by activation energies closer to their correlated motion under the evolving strain fields and thus substantially less than those calculated with respect to the perfect crystal as the reference state. The essential mechano-chemical nature of the problem is compared and contrasted with the historical literature of such phenomenon as precipitation hardening and sintering in metallic and ceramic composites.

Jan 1, 1994

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, Pso, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of 02 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By D. M. Hausen

Applications of process mineralogy to the exploitation of molybdenum ores begins with early exploration and continues through the evaluation of mineralized prospects, to amenability testwork and pilot plant studies, to the development of a mineable orebody and to the development of a viable process for recovery. After plant construction, a broad range of products from a wide selection of sampling locations, i.e. grinding circuit, flotation cells, smelters and roasting kilns. etc., are evaluated analytically and microscopically, followed by periodic troubleshooting of problem points. The various crystalline phases of molybdenum that occur naturally and throughout various hydrometallurgical and pyrometal1urgica1 processes are identified and characterized by a variety of instrumental methods, including XRD-XRF, optical and electron microscopy, infrared spectrographic and differential thermal analysis.

Jan 1, 1989

By A. V. Reddy, C. Beckermann

"The DC continuous casting of a grain refined AI-4.5%Cu round ingot with realistic boundary conditions is numerically simulated. Of particular interest are the effects of the transport of free solid in the form of equiaxed grains on the macro segregation patterns and the final grain size distribution. The study uses a previously developed two-phase model that incorporates descriptions of heat transfer, solute redistribution, melt convection, and solid transport on the system scale with microscopic models of solutal undercooling, microsegregation and grain impingement. The numerical results indicate that grain transport inhibits the formation of inverse segregation in the ingot shell and promotes negative centerline segregation. This is explained by the reduction in the solid coherency next to the mold and the advection of solute-lean grains towards the centerline. Comparisons with the experiments of Finn et al. [5] illustrate the need for considerable improvements in the model. IntroductionMacrosegregation continues to be one of the concerns in DC continuous casting of aluminum ingots. The variation in composition over the ingot cross section results in the need to adjust alloy composition in order to meet mechanical property specifications in finished products. The extent of macrosegregation is greatly affected by the casting conditions, such as casting speed, superheat, cooling rate, mold size, alloy composition, and grain refining practices. Thus, it is of great interest to develop a comprehensive mathematical model to simulate the casting process, enabling the selection of conditions that minimize macrosegregation while maintaining a high productivity."

Jan 1, 1994

By Liya Bochkareva, David Hui, Sergey Eremeev, Maksim Kireitseu, Igor Nedavniy

The principal goal of the present paper is to demonstrate an application of modern software engineering tools for modeling virtual reality and molecular dynamics of novel nanocomposites. The main technical components of presented system are I) software and nanoengineering tools for modeling of virtual reality, molecular dynamic and 30 video images of novel diamcindscontaining nanocomposites and 2) Problem tracking system to be used during modeling of virtual reality. A computational scheme and software, which utilizes neural networks and/or Microsoft. Net technique was developed to predict properties of nano-structured materials and optimization and control of nano-devices. Developed software and IT nanoengineering tools can be used by both industrial and private single users. For commercial companies proposed technology may provide better cost-effective alternative to the existing solutions for nanoengineering and modeling their virtual realit. For private users (students, professors, and engineers) proposed technology and IT tools can provide simple and cost-effective solution for nanoengineering while studying, exploring virtual reality and modeling novel nanostructures and its properties leading to an innovation or a discovery. Because of using novel software and methodologies, users can easily operate proposed technologies by available computers and operating systems (Pentium III or IV). In addition, users can upgrade it by their own self-written models, if necessary. The proposed technologies could replace or be used along with technologies for modeling such as 30 max studio and others.

Jan 1, 2004

By Veena Sahajwalla

The cupola furnace is a coke-fueled shaft furnace used as a primary melting unit in iron foundries. Control of chemical composition of the iron tapped from the cupola is a key factor in productivity and quality control. In an effort to develop a control model for the cupola, a fundamental approach based on physical and chemical principles has been taken to describe the melting process. The behavior of oxidation of the solid charge in the stack of the cupola has been studied. Sulfidation of the charge materials by sulfur-bearing components released to the furnace gases from the coke has been described. Carburization of metal droplets of iron and of steel in separate molten streams has been characterized. Finally, reactions with alloying elements in the hearth (well) of the furnace have been defined. These reactions have been described in a computer-implemented model developed to predict the composition of the iron tapped from the cupola. The model has utilized the thermodynamics and kinetics of the oxidation, sulfidation, and carburization reactions, including temperature and physical aspects, in the various zones of the melting unit. The model predictions have been compared favorably with operating results.

Jan 1, 1992

By Neng-Wen Yu, Shau-Jun Zhu, Ji-He Wei

The desulfurization process by powder injection and blowing in the RH refining of molten steel and its mechanism have been considered and analyzed. Based on the two-resistance mass transfer theory and the mass balance of sulfur in the system, a kinetic model for the process has been developed. The related parameters of the model, including the mass transfer coefficients and the effective amount of powder in the molten steel being treated for desulfurization, have been more reasonably determined. Modeling and predictions of the process of injecting and blowing the lime-based powder flux under assumed operating modes with the different initial contents of sulfur and amounts of powder injected and blown in a RH degasser of 300 t capacity have been carried out using the model. The relevant circulation rate of the liquid steel and the powder injection and blowing rate were taken to be 100 t/min and 150 kg/min, respectively. The initial contents of sulfur in the liquid steel to be treated and the amounts of powder injection and blowing were respectively assumed to be 0.007, 0.006, 0.005, 0.004, 0.003, 0.002 mass-% and 10, 8, 6, 5, 4, 3 kg/t-steel. The total treatment time for desulfurization under each mode was set up at 24 min, equivalent to eight circulation cycles of the liquid steel to be treated. The results indicated that the predictions made with this model are in good agreement with some data of the industrial experiments and practice. Injecting and blowing the lime-based powder flux with the composition of 85 mass-% lime (CaO) + 15 mass-% fluorspar (CaF2) of 3-5 kg/t-steel, it is possible to decrease the sulfur content in the molten steel to ultralow level below (5-10)x10·4 mass-% from (60-80)x 10·4 mass-%. The total treatment time needed will appropriately be 12-20 min. Intensifying the powder injection and blowing operation and increasing the circulation rate of the liquid steel may effectively' raise the rate of the process in RH refining. The model may be expected to offer some useful information and a reliable basis for determining the reasonable process parameters and help in optimizing the technology of desulfurization by powder injection and blowing in the RH refining of molten steel.

Jan 1, 2000

By Biao Zhou, Qian Li, Kuo-Chih Chou, Yi-Long Liang, Jie-Yu Zhang, Qun Luo

"In this work, the phase transformational behaviors and microstructural characteristics of 60Si2CrVAT spring steel were systematically investigated as a function of applied cooling rates in the range of 0.l-10°C/s. A quenching deformation dilatometer was used to austenize and quench. The dilatometric curves between length changes and temperature of samples suggest three characteristic stages could be identified as different ranges of cooling rates, which meets well with metallographic examination and the measured hardness results. As the cooling rate increases, the structure transformed from pearlite, granular bainite to finally martensite. The F + P and B zones are completely overlapping in continuous cooling transformation (CCI) curve, which indicates that this steel is difficult to become single bainite and shows good hardenability.IntroductionThe 60Si2CrVAT, a high-carbon low ally super-high strength steel developed from the ?OCT 60C2XFA and 60Si2MnA, is often used for coil spring of heavy vehicles and high-speed railway by hot deformation or cold deformation [1-3]. The addition of Si improves relaxation resistance significantly, through the refinement of tempered carbides as the result of the retardation of E -carbide conversion to cementite during tempering. Due to its deleterious effects on decarburization and toughness, the maxinJum content of Si has limited to 1.5 or 2.0% [4-5]. Additionally, V and Cr can improve sag resistance due to the precipitation of fine carbonitrides during hot rolling [6-7]. To best of our knowledge, the strengthening by precipitation of alloy carbides of Cr and V often referred to secondary hardening [8]."

Jan 1, 2013