Search Documents

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By E. V. Redin, B. A. Dubrovsky, E. V. Knyazev, A. I. Starikov

"Ti-V magnetite is one of the most abundant composite ore resources in the world. This ore cannot be fully processed via blast furnace technology because of high content of Ti02. According to the investigations carried out in the USA and Japan ITmk3 RHF (Rotary Hearth Furnace) technology is a breakthrough in Ironmaking. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from Ti-V magnetite ore via the ITmk3 by means of the lab scale testing. Samples of ore from the Maly Kuybas deposit (Southern Ural), carbon reductant and fluxes were chemically analyzed. Green pellets were processed via a lab chamber furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities [l]. After pilot testing at Kobe Steel's Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics put into operation the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota) in 2010. Results were consistent with nugget characteristics confirming ITmk3' s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from the Ti-V magnetite bearing ore with high content of Ti02 and Alz03 has been done. It is well known, if a lot of Ti02 and Alz03 enter the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace. Besides, high content of Alz03 raises the melting temperature of gangue minerals disturbing the coalescence of reduced iron to the nuggets."

Jan 1, 2013

By Bohumir Jelinek, Sergio Felicelli, Mohsen Eshraghi

"We present a parallel lattice Boltzmann - cellular automaton model of the two-dimensional dendritic growth during solidification of binary alloys. The model incorporates effects of solute and energy transport under melt convection. The parallel performance of the algorithm is assessed. A loss in the parallel efficiency is observed when multiple computational cores per processor are utilized. Excellent strong scaling up to thousands of computing cores is obtained across the nodes of a computer cluster, along with the near-perfect weak scaling up to forty thousand cores. The presented solidification model shows a good scalability up to centimeter size domains, including millions of dendrites.IntroductionLattice Boltzmann method (LBM) is an attractive numerical technique for solving fluid dynamics problems. Its advantages are simple formulation and locality, with locality facilitating parallel implementation. In the present model, interface kinetic is driven by the difference between local actual and local equilibrium liquid composition [1]. The cellular automaton (CA) technique is deployed to track the solid-liquid interface [2]. A serial version of the present LBM-CA model with a small number of dendrites was validated against theoretical and experimental results in the previous publications [3, 4]. In this work, it is the first time that simulations with millions of dendrites were performed, something not possible with the computationally much more costly phasefield method [5].This research effort examines a technique for simulations of millions of dendrites in centimeter size domains, including thermal, convection, and solute redistribution effects. Nearly ideal scaling properties of the model are demonstrated. This extensively large landmark was achieved because of• the CA technique being two orders of magnitude faster than alternative, phase-field methods [5]• highly parallelizable LBM method, convenient for simulations of flow within complex and time dependent boundaries• availability of the powerful NSF Extreme Science and Engineering Discovery Environment (XSEDE) supercomputing resources"

Jan 1, 2013

By E. V. Verhoef

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-lndicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LeA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LeA assessments, thus leading to erroneous results. The suggested approach provides directions for including these external effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By E. V. Verhoej

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-Indicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LCA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LCA assessments, thus leading to erroneous results. The suggested approach provides directions for including these extemal effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By Liang Li

Thermodynamic analysis and experiments were conducted in order to verify the feasibility of preparing crude titanium tetrachloride (TiCl4) via the carbochlorination of low-grade titanium slag in molten salt. Titanium slag, assaying 74.6 wt% TiO2 with high calcium and magnesium oxide impurities, was treated by an optimized carbochlorination process in NaCl molten salt. These impurities in the titanium slag were chloridized simultaneously, and chlorination products FeCl2, MnCl2, MgCl2, CaCl2 and CrCl3 were collected in the furnace slag. XRD and SEM/ EDS analysis of residue shown that SiO2 and Al2O3 in titanium slag were difficult to chlorinate completely. Theoretical calculations and industrial-scale experimental studies reveal the content of TiCl4 in the products was more than 98.8 wt% and thus proved the feasibility of utilizing low-grade titanium slag for TiCl4 preparation by molten salt chlorination technology.

By Mohamad Omarei, S. M. Sadrameli

"The aim of this research work was to produce biodiesel (fatty acid methyl esters, FAME) from canola oil using KOH loaded on y-Al203 support as a heterogeneous catalyst. Different parameters such as effects of the molar ratio of methanol to oil, catalyst amount and reaction time on the yield were investigated. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were used for characterization of the catalysts. A biodiesel yield of 86.67% was obtained under catalyst preparation and transesterification conditions of calcinations temperature of 773 K, 4 h of reaction time at 338 K, and using 3.5 wt% catalysts and molar ratio of methanol/oil of 15:1. The leaching of potassium species in the spent catalyst was observed.1. IntroductionBiodiesel is an eco-friendly and alternative energy source for diesel engines that can be synthesized by transesterfication of vegetable oil or animal fat with alcohols [1 ]. There are four principal approaches to the synthesis of biodiesel involving the transesterification of the triglycerides of the plant oils and animal fats: base catalysis [2], acid catalysis [3-5], employing supercritical alcohol conditions [6] and enzyme catalysis [7]. The commonly used homogeneous catalysts are NaOH, KOH and their alkoxides. Homogeneous alkali-catalyzed transesterification is much faster than acidcatalyzed transesterfication [8]. However, a large amount of water is required to transfer the catalysts from the organic phase to a water phase after the reaction. Therefore, it is considerably more costly to separate the catalyst from the produced solution [9]. These disadvantages could be removed by use of a heterogeneous catalyst [10]. The use of heterogeneous catalysts eliminates the neutralization step, hence it results much easier to separate from liquid products. Also, they can be designed to give a higher activity and selectivity and to have longer catalyst lifetimes [11]. A large number of different heterogeneous catalysts have been synthesized for biodiesel production. For example, calcined Mg-Al hydrotalcites [12], zeolite and metal catalysts [13], metal oxides such as calcium oxide (CaO) [14], magnesium oxide (MgO) [15], zirconium oxide (Zr02) [16], and supported catalysts [17] have been investigated as heterogeneous catalysts. CaO and MgO are most frequently used heterogeneous catalysts for biodiesel production [18]. In this present work, we aimed at developing an efficient catalyst for transesterification of canola oil. We have prepared KOH/ Al203 by impregnation and applied to determine the optimum conditions for biodiesel production. Three different variables including reaction time , alcohol to oil molar ratio and catalyst loading with may influence the quality of the produced biodiesel were optimized. Moreover, SEM (scan electron microscope), XRD (X-ray diffraction) and XRF were used for characterization of the catalysts."

Jan 1, 2012

By D. A. Salinas G., A. H. Castillejos E.

Pachuca tanks are commonly used in the hydrometallurgical industry to carry out leaching operations. The fluidynamic characteristics of the liquid phase, resulting from the injection of gas into the draft tube, are important to achieve the complete suspension of the mineral particles and has a decisive influence in the mass transfer processes occurring in this reactor. This study investigated the effect of different design and operating characteristics on the liquid velocity field. using a laboratory-scale Pachuca tank. The transparent model was filled with water, and air was injected through the bottom in the absence of mineral particles. The liquid velocities over the whole reactor were measured under several experimental conditions using particle image velocimetry (PIV). This technique allowed to obtain a very detailed picture of the liquid motion even in the draft tube, as long as bubbles were absent from the measured field of view. The experiments have shown that the liquid velocities increase with increasing the draft tube to tank diameters ratio, the distance from the conical bottom to the draft tube entrance, or the gas superficial velocity. On the other hand, an increase in the water level with respect to the draft tube outlet caused a decrease. A mathematical model, which used the no-slip model, to calculate the variation of axial effective density along the two-phase region, was found to predict liquid velocity fields which agree very satisfactory with the experimental results obtained under all the conditions studied.

Jan 1, 1999

By James C. Foley, David K. Rehbein

"In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent ·advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ evaluations of the acoustic attenuation and velocity as sintering proceeds. Pure aluminum (99.999%) and aluminum alloy powders were prepared with high-pressure gas atomization (HPGA). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and attenuation during sintering. The changes in acoustic properties were correlated with sample microstructures and mechanical properties. Evolution of the acoustic echo train during sintering is shown to provide information on the state of sintering as well as having the potential for detection of interior flaws.IntroductionThe versatility of powder metalallurgy (PIM) technology in the manufacture of complex shapes has enabled an increasing amount of wrought and casting production capacity to be converted to PIM technology. However, ultrasonic inspection of green components produced using PIM techniques remains a challenge and is not generally practiced [1]. Inspection of PIM components in the green state is highly desirable, because the green part can be reclaimed with only accepted components being subjected to further costly processing. Another potential benefit is characterization and greater understanding of the sintering process itself. An increased scientific understanding of the sintering process enables intelligent process control, greater reliability of the production process and a lower rate of rejection of the finished product. In order to realize these potential benefits, it is necessary therefore that accept/reject criterion be based on real time nondestructive evaluation of the green-state components and the sintering process.Most current nondestructive inspection techniques suffer from their inability to perform inspections below the near-surface region with the exception of X-ray and to some extent pulsed eddy current [2]. X-ray inspection requires extensive shielding of production personnel and expensive film and film processing. While development of pulsed eddy current techniques have lessened the impact of the well-known skin effect, the depth of penetration of the induced eddy currents remains somewhat of an issue [2]."

Jan 1, 2000

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

"In order to make the stainless steel making process efficient and environment friendly, it is essential to minimize the loss of chromium to the slag phase. With a view to investigate the advantages of using CO2 to attain moderate oxygen partial pressures in the oxidant gas during the decarburizations of stainless steel, the present experiments were carried out to understand the oxidation kinetics of Fe-Cr alloys and Fe-V alloy with gas mixtures containing CO2. In the present work, the oxidation behavior of Fe-Cr and Fe-V was examined by thermogravimetric analysis (TGA). Various mixtures of O2 and CO2 were used as the oxidant gas and the oxidation rate was followed by the weight changes as a function of time.The experiments demonstrated that the oxidation rate is independent of temperature at present experimental situation, but has strongly related to the Cr-content of the alloy as well as the oxygen partial pressure in the oxidant gas mixture. The wetting of alumina by the iron drop and the change of the drop shape during the course of the oxidation were investigated by X-ray radiography."

Jan 1, 2010

By Bing Li, Miao Shen, Qiang Wang, Yuqi Chen

Electrochemical methods including cyclic voltammograms, square wave voltammograms, chronopotentiometry are applied to characterize the reduction potentials of Na+ and Li+ ions in LiCl-KCl melts. According to theoretical calculation, the reduction potential for Na+ is slightly more negative than Li+ in NaCl-LiCl-KCl melts at 450℃. However, by electrochemical measurements, the reduction potential of Na+ is slightly more positive than Li+ in the above melt and the potential difference between Na+ and Li+ reaches 0.16-0.2V on an inert W electrode in 1.0-2.0 wt% NaCl-LiCl-KCl melts. An active Pb electrode is used to improve the removal rate of Na+ from LiCl-KCl melts. The reduction potentials for both Na+ ions and Li+ ions on a Pb electrode shift to more positive values and the reduction currents become larger. After 6h electrolysis on a Pb electrode at -3.0V, the practical removal efficiency of Na+ ions reaches 90.12% and the reduced products contain metallic Na and Li with a Na/Li mass ratio of 4.25/1.

Jan 1, 2015

By Dai Yongnian

"The feasibility to vacuum distillation of a crude metal or an alloy was discussed. The equilibrium relationship between vapor phase and liquid phase in A-B system - - - - - PA/PB =BAa*/b has been derived. The separation coefficient, BA = rAPA/(rBPB) is a judgment criterion. By calculation PA/PB, the equilibrium composition diagram of vapor phase and liquid phase was drawn. By use of the equation derived by M. Olette, the relationship among the volatilization amounts of various impurities in a crude metal (yi) was further solved. 1-(X/100)= C =(1-Y1/100)1/02i . From yi value obtained in practice, 2i, Pi and then can be calcu-lated. The correct volatilization order of various impurities was obtained. These results can be applied to determine the practical conditions (temperture, vacuum degree, type of distilla¬tion furnace, times of distillation and control of product composition) in distillation of a crude metal or an alloy.INTRODUCTIONRefining and separation of various impurities from nonferrous crude metals by vacuum distillation have many the advantages of high metal recovery, impurities recovered in metallic state, flowsheet simplified, good enviromental protection, low operation costs and in complex equipment. So in recent years this method has been adopted widely.Vacuum distillation has also been studied and used in separation of various elements from non-ferrous alloys and the area of its application is being extended rapidly.At this situation, some problems have been put up: What kind of impurities can be removed from crude metals? What kind of alloys can be separated by vacuum distillation? In present paper, attemps have been made to answer these problems and combine with practical results to analyse some valuable data obtained from testwork on vacuum distillation of crude tin and Pb-Sn alloy."

Jan 1, 1988

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite,(Cu2S) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical equilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

By E. Allaine

Carbochlorination kinetics of pure MoO3, Nb2O5, Ta2O5 and V2O5, by Cl2+CO+N2 gas mixtures was investigated between 380 and 1000 °C. Standard free energy of carhochlorination reactions and phase stability diagrams of these refractory metal compounds were calculated. The influence of total gas flow rate, temperature, reactants partial pressures on the reactivity of these oxides were investigated. The apparent activation energies were found to be about 83, 75, 110 and 100 kJ/mole below 650°C for MoO3, Nb2O5, Ta2O5 and V2O5, respectively. Above this temperature, the Arrhenius plots exhibit a rate anomaly attributed to thermal decomposition of COCl2 and/or structural changes of these refractory metal oxides. The apparent reaction order of carbochlorination of these oxides with respect to Cl2+CO was determined. For these refractory metal oxides, the reaction rate was maximum for a Cl2/CO ratio of about 1 in the chlorinating gas mixture. Results of carbochlorination of these oxides are compared and discussed.

Jan 1, 1995

By Bien Ferrer

In most smelting operations, there is a strong incentive to improve safety, reduce downtime and extend the campaigns of furnaces and related equipment. An asset management strategy that is based on information, rather than simple throughput metrics and intuition, can be developed to improve uptime and unlock value currently unrealized at existing smelters. Advances in digital technology, including data analysis, modelling and monitoring for hot pyro-metallurgical vessels, make it possible to assess the current condition of an asset, as well as to make more informed projections about its future condition, using on-line and historical data. This would allow practices around asset management to be more proactive and less reactive, with the end-result of optimized uptime. ‘Digital Asset Management’ describes a concept in which digital technology is used to support an asset management strategy and accelerate decision-making by providing information on what, why and how an asset should be designed, operated or maintained. With the overall goals of effective resource utilization, optimized operations, capital efficiency and social acceptance, Smelter 4.0 is a program of holistic improvement and is underpinned by the effective use of data to drive decisions. This paper focuses on Asset Reliability, which is one of the improvement pillars of Smelter 4.0, and introduces a methodology that is aimed at closing the gap between recorded data and evidence-based decision-making through Digital Asset Management.

By Mark William Kennedy

Modern metallurgical plants typically have complex flowsheets and operate on a continuous basis. Real time interactions within such processes can be complex and the impacts of streams such as recycles on process efficiency and stability can be highly unexpected prior to actual operation. Current desktop computing power, combined with state-of-the-art flowsheet simulation software like Metsim, allow for thorough analysis of designs to explore the interaction between operating rate, heat and mass balances and in particular the potential negative impact of recycles. Using plant information systems, it is possible to combine real plant data with simple steady state models, using dynamic data exchange links to allow for near real time de-bottlenecking of operations. Accurate analytical results can also be combined with detailed unit operations models to allow for feed-forward model-based-control. This paper will explore some examples of the application of Metsim to real world engineering and plant operational issues.

Jan 1, 2014

By C. S. Simons

This paper presents a review of the extractive processes used in the production of nickel, with emphasis on developments since the beginning of the Second World War. Attention is given to the factors, many outside the nickel industry itself, which determined the direction of process research and strongly influenced the ultimate commitments to industrialize the resulting developments. An example of such a factor is the sudden surge in demand, far exceeding the then available nickel production capacity, that was caused by the advent of World War II; the result was the first serious consideration ever given to low- grade laterites as a viable source of primary nickel. Other factors discussed include such items as process development in the extraction of other metals - particularly copper; the availability of increasingly sophisticated materials of const- ruction; the advent of the "environmentalist" and related political developments; the massive escalation in the price of energy - particularly oil. The paper concludes with an attempt to forecast the nature of the most effective nickel process of the future, based on extrapolation from the economic and political situation that exists today.

Jan 1, 1988

By Yonggang Liu

Microstructure and precipitates in hot rolled low carbon steel sheet by CSP were investigated in this paper. It is pointed out the precipitates in low carbon steel sheet by CSP are different with that by traditional hot rolling. The bainites were found in CSP hot rolled steel sheet by TEM testing and these bainites could maintain in the sheets even after batch annealing. The selected area electron diffraction analyzing indicated that there were many CrB2BN and FeB4BN phases precipitated in hot rolled steel sheet and no AlN grains precipitated. The nitrides forming can limit AlN grains precipitating during the batch annealing processing, and this could do harm to the texture pipeline along orientation line forming with formed properties.

Jan 1, 2006

Laminated ceramics have received widely scientific and commercial attention because their properties, such as mechanical properties and electrical properties, can be tailored by adjusting the structure, thickness and composition of the different layers. For example, ferroelectric Bi4T13O12 (BIT) which has a positive temperature coefficient of dielectric constant (TE) can be used to modify the negative of typical microwave dielectric ceramic BaNd2Ti4O12(BMT). However, BaNd2Ti4O12/Bi4Ti3O12/BaNd1Ti4O12 (BNT/BIT/BNT) laminated ceramics could not be prepared by the general method because the optimal sintering temperature of BaNd2Ti4O12 ceramic (around 1350°C was much higher than that of Bi4Ti3O12 ceramic (around /1100°C). in this research, a new method of spark plasma sintering (SPS) combined with post-sintering was successfully proposed to prepare BNT/BIT/BNT laminated divided proposed to prepare ceramics. It was divided into three steps. In first step, the BaNd2Ti4O12 ceramics were prepared by conventional sintering method. In second mop, the calcined and pre-pressed Bi4Ti3O12 powders were sandwiched between BaNd2Ti1O12 ceramic pellets and spark plasma sintered at 900&apos;C for 10min to synthesize BNT/BIT/BNT composite ceramics. In the last step, a post-sintering was employed to reoxidize the partially reduced BNT/BIT/BNT composite ceramics. The results of scanning electron microscopy (SEM) and electron probe mircoanalysis (EPMA) showed that BNT layer and BIT layer were well bonded and no significant interfacial infiltration between them was observed. The sandwiched BNT/B1T/BNT ceramic with 10.7% BIT in volume has a dielectric constant of 92.8, a low dielectric loss of 0.0068 and a small temperature coefficient of dielectric constant v/35 ppm/C at 1 MHz.

Jan 1, 2003

By O. Forsén

In the first part of this paper is studied the behaviour of small amounts of impurity elements? in the solidification of copper anodes. In the second part the dissolution of these impure anodes in sulphate based electrolysis is discussed. The first part is introduced with practical examples, the .model of solidification of impurities during the solidification of anode copper. According to this model the solidification structures of anode copper are strongly influenced by both thermodynamic and kinetic factors. Thermodynamics determine the microstructure of anode copper, but kinetics can alter the composition of melt to such that there is formed unequilibrium structures during the solidification, especially when the residual melt is solidified. The electrolysis experiments have clarified the behaviour of impuririties in the electrochemical dissolution in sulphate. Based copper electrolysis. In this study it is widely investigated to what extent any impurity elements or oxides will dissolve. In copper electrorefining. With the aid of the electrochemtcal experiments it was possible to fulfil quantitatively the qualitative results accomplished by microstructure studies.

Jan 1, 1985