Search Documents

By Markus Aspiala, Fiseha Tesfaye, Pekka Taskinen

In this paper, the standard thermodynamic properties of Ag3Sb and Ag6Sb intermetallic compounds have been studied by the solid state EMF-method, using Ag+ ion conducting β- alumina and AgI. The intermetallic compounds were synthesized from pure substances in evacuated silica ampoules and their formation were confirmed by the SEM-EDS analyses. The EMF measurements were made on electrochemical cells of the type [Ag | β-alumina | Ag-Sb] and [Ag | AgI | Ag-Sb]. The usage of β-alumina electrolyte, in this study, enabled thermodynamic measurements of the Ag-Sb-intermetallic compounds above 710 K, hitherto unreported. Based on the new experimental data, thermodynamic properties of the Ag-Sb-intermetallic compounds have been determined. The obtained experimental values have been compared with the available literature data.

Jan 1, 2015

By G. Lindkvist

Roasting of concentrates with high impurity levels is normally done in multiple- hearth furnaces where the concentrates are heated with oilfired burners in order to remove As, Sb and Bi before the final sulfide oxidation. Although it is a countercurrent heat exchange process it uses a lot of oil. In order to develop an energy saving, and from a working environmental point of view a less harmful process than the multiplehearth process, pilot-plant tests have been done in a two-stage fluidized bed for partial roasting. The test materials have been As-rich concentrates with 8-25 % As some 5b and Bi. The Cu-content was 0-28 %. The tests have been successful with <0.3 % As,in the calcine and with an elimination of 5b between 80 and 90 %. In order to achieve the proper conditions for good impurity removal, 1.e. right temperature,residence time and sulphur potential, the tests were performed in a special designed roaster. The roaster consists of two beds with the facilities for recirculation of calcine, preheating of the blast, and possibility to use oxygen enrichment. The construction makes it easy to control the reactions that generate the heat in the bed and reduce the amount of dust that passes through the cyclones. As two roasting steps are used, the possibility to obtain optimal conditions for impurity removal is improved and the calcine can either be smelted to a normal matte, or after being dead-roasted in the second stage, be leached in the normal way for gold extraction. The calcine was smelted with slag. The matte and the slag obtained had low quantities of impurities in the matte and a favourable distribution of impurities to the slag.

Jan 1, 1983

By B. Erik Ydstie, Tor Lindstad, Vianey Garcia-Osorio

"As a result of the high temperatures present in a Carbothermic Aluminum Process the content of aluminum and aluminum sub-oxide in the gases leaving this process is high. These gases as well as energy must be recovered. In a Vapor Recovery Unit were the aluminum compounds react in a series of Heterogeneous Non-catalytic Reactions forming solid, liquid and gas products. The different product phases depend on the temperature present in the system. In this work we present dynamic model of the Vapor Recovery Unit of a conceptual Carbothermic Aluminum Process. Because of the complexity of the system several models are developed and coupled to capture the essential physics of the multiphase reaction problem. A Shrinking Core Model describes the reaction mechanisms. Then material and energy balances are coupled with the thermodynamics properties from the FACT database of thermodynamic properties, resulting in a system of nonlinear Partial Differential Equations. In the paper we describe the model development and governing equations for the reaction mechanisms and fluid flow. Finally we review the numerical schemes created for the solution of the model system. The model can be used for control and design purposes.IntroductionThe Carbothennic Processes for producing Aluminum can be divided into two groups (Motzfeldt et al. (1989)) In the first approach pure alumina is produced and reduced to pure aluminum. In the second approach an alloy (e.g. aluminum and silicon) is made and then aluminum is produced from the alloy. The history of both processes has been described by Ginsberg et al. (1965). At least three aluminum producers began largescale testing of this process in the 60's Alcan, Pechey-Ugine and Reynolds. Alcoa did some smaller scale experiments.Alcoa was one of the first companies to produce aluminum by Carbothennic Reduction (Foster et al. (1956)) and US Patent 2,829,961 April 8, 1958. In this process a carbon containing molten aluminum phase was a floated on top of an oxy-carbide melt. During the cooling the dissolved carbon deposited as aluminum carbide. The carbide was then separated from the molten aluminum by a fluxing agent. This process was successful but economic unfeasible."

Jan 1, 2001

By G. D. Sandrock

The science and technology of roan temperature rechargeable metal hydrides began about 1969 with the discoveries that the intermetallic Compounds LaNi5 and TiFe could be, conveniently hydrided and dehydrided at roan temperature and modest H2 pressures. Subsequently, this lead to the development of a broad family of REE-containing AB5 hydrides and numerous applications that make use of the extraordinary H2-absorption and reaction-heat properties of these materials. Some of the applications include H2 storage, compression and separation, as well as heat pumping, heat to mechanical energy conversion and electric energy storage. This paper briefly reviews the fundamental phenomenology of metal hydrides, the history of the use of REE&apos;s in rechargeable metal hydrides, the practical engineering properties of these materials and the applications that have evolved around them. The rechargeable nickel metal hydride battery, a new vial alternative to NiCd cells, stands at the forefront of the applications.

Jan 1, 1992

By David G. Dixon

Although the kinetics of leaching processes are of paramount importance in the design and analysis of nearly all hydrometallurgical flowsheets, these concepts remain poorly understood and, as a result, are only rarely applied to mass and heat balance models. In this second of two papers, we demonstrate how simple yet powerful models of leaching kinetics and other rate processes may be added to mass and heat balance models, and apply these concepts using a spreadsheet model of a simplified pyrite autoclaving flowsheet. In particular, we focus on the interpretation and scale-up of batch leaching data, and on simple means for modeling other phenomena commonly associated with leaching, such as reagent depletion, gas-liquid mixing, and the precipitation of oxides and basic salts.

Jan 1, 2002

By Guohua Bai, Lin Zhang, Shan He, Xuling Chen, Min Gan, Xiaohui Fan, Yanbin Tang

"For reducing the dust content in flue gas during copper smelting in the Ausmelt, technologies and mechanism of strengthening the pelletizing of copper concentrate were studied. The results show that adding bentonite, organic binder or composite binder can effectively enhance the strength of green pellet and reduce the rate of shedding powder in drying process, and composite binder works best. When adding 1 % of composite binder, the drop strength of green pellet increased from 1.9 times/P to 4.5 times/P, the rate of damage dropping from 2 m reduced from 50.12% to 13.08% and the rate of shedding powder reduced from 60.28% to 25.13% at drying temperature of 400111. In addition, the mechanism of binder absorbed in the surface of mineral was investigated by infrared spectroscopy. The results showed that composite binder absorbed in the surface of copper concentrate was in the form of chemisorptions, which made hydrophilic enhanced, while bentonite absorbed in the surface of copper concentrate was physisorption.IntroductionWith the technologies of copper smelting developing, the equipment of copper smelting steps into a large-scale and efficient level in recent years. As Ausmelt smelting is characterized by being efficient, environmentally-friendly and energy-saving, it is generally recognized by the enterprises of copper smelting [l]. The process of Ausmelt smelting starts with materials mixing, and then pelletizing. From this point onwards, pelletized balls are charged to the top of the furnace, undergoing drying and smelting reaction[2]. Since copper concentrate is fine-grained, directly adding into smelting furnace can make it blown out of the furnace together with the airflow upwards, rendering flue gas high in flue dust, which can cause the loss of concentrate greatly, and make smelting environment poor as well. The concentrate transported into the furnace and smelted after disc balling is conducive to improve the capacity of melting furnace during copper concentrate smelting, reduce the powder shedding rate and improve enterprise benefits."

Jan 1, 2013

By Tateo Usui

In the course of carbonization of coal under a rising temperature condition, volatile matter (V.M.) is released. The kind and amount of V.M. released depend on the kind of coal. Components of V.M. are tar, hydrocarbons (CH4, C2H4, C2H6, C3H8), CO, CO2 and H2, which are released in this order as a function of carbonization temperature. When the carbonization of coal under a rising temperature condition is interrupted at a certain temperature, TC, max, semi-coal-char with residual V.M. is obtained. If some optimum interruption-temperature is chosen, small but most suitable amount of V.M., namely H2, is retained. When the semi-coal-char thus obtained is heated again under the same rising temperature conditions but up to more than TC, max (1), the residual V.M. is released from just around TC, max (1). We propose novel iron ore agglomerate bearing such semi-coal-char with some strength. While simple iron ore agglomerate bearing coal char will start the reduction reaction as solid-solid reaction at somewhat higher temperature, the proposed one will start the reduction reaction as gas-solid reaction at somewhat lower temperature but a little higher than TC, max. Samples of semi-coal-char and novel iron ore agglomerate bearing such semi-coal-char have been prepared and evaluated.

Jan 1, 2006

By Marion Dattilo

The search for an improved anode for the electrowinning of lead from fluosi1icic acid medium has led the U.S. Bureau of Mines to investigate composites. Polymer bonded metal oxide powders which may contain catalyst additions were prepared by pressing. These composites display an improved activity toward the oxygen evolution reaction over electrodeposited lead dioxide on titanium, carbon, and nickel substrates. These composite electrodes contain 5 to 10 wt. " binding polymer, with the balance being metal oxides. Lowered anodic potentials achieved using the compnsite anodes resulted in lower levels of lead dioxide deposition during electrowinning.

Jan 1, 1995

By M. W. Kennedy

Prediction of the thermal duties of copper coolers in freeze lined furnaces is challenging. Where copper coolers are immersed in liquid slag the heat transfer is often defined by a natural convection cell immediately adjacent to the wall, in the absence of other factors producing forced convection. Slag coolers are typically not fully immersed, slag temperature, liquidus and superheat can vary, and bath levels may change significantly with batch tapping, leading to substantial variations in radiation heat fluxes. Radiation heat transfer is discussed with reference to the non-obvious impact of slag liquidus on radiation losses in the exposed cooler sections. Reference is made to literature and the results of analytical and FEM models.

By Kotaro Ogura

"The electrolysis process in which CO2 is selectively reduced to C2H4 at a three-phase(gas/solution/metal) interface on a copper-mesh electrode has been developed in a concentrated solution of potassium halide. At open-circuit potential, CO2 is captured on the electrode by being inserted into the double-layer consisting of halide anions specifically adsorbed and potassium cations which are located in the Helmholtz inner and outer layers, respectively. CO2 thus activated is subjected to the electrochemical reduction. In the early stage of reduction, CO2 is converted to formate radicals that are adsorbed on the electrode by taking the place of halide anions. The reductive coupling of these radicals results in the formation of intermediates such as -CH2C(O)- and CH2=CH-, and C2H4 is finally produced. The catalytic activity of the electrode process involving the insertion of CO2 into the double layer is not deteriorated at all during the electrolysis, and the continuous reduction of CO2 to C2H4 is possible with the addition of inorganic acid under the assistance of natural energy.Carbon dioxide is a serious pollutant released from fossil fuel power station, internal combustion and many industrial operations. The easy release of CO2 to the air has caused the global warming, and the technique which intends to curtail CO2 by pushing it back into the ground has been suggested. However, this problem should be greatly mitigated if CO2 can be converted to innocuous substances. Especially, the reuse of CO2 as fuels and chemicals is extremely effective not only for the mitigation of the global warming but also against the depletion of the fossil fuel reserves. Several processes for converting CO2 to valuable compounds have been proposed including hydrogenation over heterogeneous catalyst at high temperature and electrochemical and photochemical reduction. In the conversion and cutback processes of CO2, however, it is of importance that the process is feasible under mild conditions, because the secondary generation of CO2 is feared if high energy is required and supplied with a fossil fuel. In this meaning, the electrochemical reduction of CO2 taking place at room temperature, which is similar to photosynthesis, is promising. From the practical point of view, it is further necessary that the conversion rate is high enough and the product is satisfactorily valuable."

Jan 1, 2008

By G. C. Gullo, H. Wabusseg, P. J. Uggowitzer, H. Kaufmann

"The basic concept of New Rheocasting (NRC) is described and the application of wrought alloys with this process is discussed. Practical experiments with the aluminium alloy AIMgSi I are explained. For this alloy the proper NRC - casting temperature was determined by using Thermo Cale - computer software and DT A and the essential processing conditions are shown. In the experiments the melt was taken from an aluminium holding furnace and cast into NRC steel cups. After controlled cooling the resulting slurries were cast into a 4-step die on an UBE HVSC 350 Squeeze Casting machine. The characteristic microstructural values such as grain size and shape factor were measured and compared with classical casting alloys. The influence of the wall thickness of the step part (6 mm, 10 mm and 14 mm) on the microstructure is described. Tensile properties in different heat treatment states are compared with characteristic prope1ties of the same alloys in forged condition. The ew Rheocasting - process CNRC)The NRC process is a recently developed new semi-solid processing method which allows the production of pore-free, pressure tight components.In the NRC process a fu lly liquid, but only slightly superheated melt is taken from a holding furnace and poured into specially designed steel crucibles, which are placed on a carousel next to the Vertical Squeeze Casting machine. In this ,NULL,slurry maker'· globul ar a-Al grains grow, following forced homogeneous nucleation at the cup wall [ 1, 2]. In the few minutes during which the melt is cooled to sem i-so lid processing temperature, a stable ske leton of a-Al phase forms. The resulting slug keeps a cylindrical shape during its slide into the sleeve of the Vertical Squeeze Casting machine, where it is cast into shape."

Jan 1, 2000

By R. W. Lawrence

A method by which it is possible at an oxidation potential below 680 mV SHE to achieve quantitative conversion of sulphide sulphur to elemental sulphur instead of sulphate in a biological leach of chalcopyrite and bornite has been investigated. The process chemistry, biological phenomena and process flowsheet options are discussed. Several copper concentrates have been evaluated and have been found to be amenable to th process. Results to study the progression of chalcopyrite decomposition during the leach are presented and mineralogical factors affecting the requirement for silver addition are discussed. A chloride addition method for improving silver recovery is described. The results of a small scale continuous leach test have demonstrated that continuous operation can be carried out with high copper extraction and stoichiometric conversion of sulphide sulphur to elemental sulphur.

Jan 1, 1985

By Qiang Zhong, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

Viscosity of slag determines the production efficiency, energy consumption and distribution of elements between metal and slag, which is very important for pyrometallurgy. Slag of goldantimony ore blast furnace smelting has seldom been studied. In this paper, the viscosities of gold-antimony ore smelting slags of different composition have been studied by the rotating cylinder method. The results showed that, for a slag of 38.95% SiO2, 16.17% CaO, 25.97% FeO, 10.25% Al2O3, 5.17% MgO, the viscosity can be decreased by reducing 3.24%-8.5% SiO2 or increasing 3.31%-9.56% CaO content. Complex SixOy z- from SiO2 acts as the main cause for the high viscosity in a slag of high SiO2. The increasing of CaO causes the decreasing of the amount of SixOy z- and the O2- dissociated from CaO breaks the complex SixOy z-, which can decrease the viscosity. Viscosity of different composition slag in the appropriate range temperature can be calculated from the Arrhenius equation.

Jan 1, 2015

By Deepu Philip, Pratik Agarwal, Ajay Kumar Shukla, Ishani Shukla, G Rajesh

Steel plants generally employ static BOF end point control models to arrive at a given temperature and chemistry at the end of blow. These end point models have now been supplemented with chaos control models to steer the blowing process in the right direction while the blow is in progress. Merely arriving at the correct end point temperature is however not adequate because in the subsequent stages as well the temperature variations can be large and unpredictable. The present paper deals with an integrated model to take into account the effect of all parameters affecting temperature and composition from tapping to the start of casting to minimize the use of LF or aluminum heating, and also minimize grade mixing. The application of lean operations strategy is explained in which the previous “Push System’ is changed to a “Pull System”, minimizing the use of ladle furnace or aluminum heating during steelmaking.

Jan 1, 2014

By Zhen Zhang, Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie, Hong-Yi Li

Extracting vanadium from vanadium containing hot metal by LD process has been proven an effective solution for the utilization of vanadium-titanium magnetite ore, but the systematic analyses of vanadium extraction rate and mechanism by basic slag are seldom reported. In this study, mathematical model of vanadium transfer from metal to slag was formulated and the rates of vanadium extraction of hot metal with basic slag were investigated. The results indicated that the apparent vanadium extraction rate constant, kp, were in the range of 1.33~9.07×10-4g/(cm3·s). And the rate constant was increased with the increase of final slag basicity, reaction temperature and stirring gas flow. The apparent of mass transfer parameter decreases significantly from 0.13 cm3/ s to 0 cm3/ s in 20min, and the data changed as negative due to the decrease of slag oxidation and recovery of vanadium from slag to metal.

Jan 1, 2015

By Augusto Viana Leandro Teixeira

Rare Earth Elements (REE) are fundamental for modern life products and green technologies. Supply constraints and the price peak of 2011 boosted intensive research for alternatives for processing and separation. Complex monazite- type, rare earth ores usually contain high acid consumption impurities, such as iron and aluminum, and radioactive thorium in their composition. These impurities are not removed by conventional concentration processes due to fine, micro-level association between the REE carrying minerals and the gangue minerals. This work presents a selective process route for REE extraction from iron-rich, monazite ores. The process involves sulfation by addition of concentrated sulfuric acid and pyrohydrolysis at temperatures of approximately 700–750 °C. Experimental results show REE extraction higher than 70% and low iron (below 5%) and thorium extraction (below 10%). A method based on thermogravimetric analyses was shown to be adequate to predict the behavior of a given ore sample in the sulfationselective pyrolysis-leaching process.

By John H. Schloen

Copper refineries are constantly looking for methods to upgrade their plants to reduce refining costs and to improve the purity of their electrolytic cathodes at the same time that the purity of the anodes they refine is being lowered by the rehabilitation of reverberatory furnace smelters to one of the direct smelting processes. The comments given below are based on the answers to the questionnaire returned bf the 36 copper refineries that represent 66% of the western world s refining capacity. Eleven refineries employ some form of uniform weight anade casting, e.g., Outokumpu, Contilanode, Mitsubishi, Lurgi, or Hazelett. This type of anode casting presents the best possibility for improving cathode purity. The cathode press of Phelps Dadge can improve current efficiencies and cathode quality. The press is used on first-run cathodes, after 48-60 hours, on half-cells at a time without interruption of the cell current. One refinery interrupts current for sever.al hours to allow the anode slime to settle before the, cathode pressing. The cathode press is now used at eight refineries. Apart from periodic reverse current (PRC), it is not expected that current densities will be increased. Thirty refineries, using direct current, average 231 amps/M, with a low of 178 and a high of 350. Five refineries use PRC at an average of 338 amps/M, with a low of 290 and a high of 380. Current efficiencies are good at an average of 94%, with a low of 88% and a high of 99% for the 34 refineries that reported. It must be remembered that the cycle efficiency with PRC is about 93%., so that the effective current efficiency with PRC would be only .94 X .93 or 87% However, PRC should be considered seriously for refinery expansions because it can save about 25% on capital costs.

Jan 1, 1987

By P. D. Lee

The effect of strontium on porosity formation in aluminum-silicon alloys is not well understood and there is no consensus upon the cause of the effects observed. This paper describes a series of experiments where the effect of adding strontium on pore formation was observed directly with combination of a traditional temperature gradient stage and real time micro-focus radiography. These in situ observations provide a new insight into the effect of strontium on the nucleation and growth kinetics of porosity. The addition of strontium was found to have a minor effect on the growth of the pores in the mushy zone. However, strontium appeared to alter the nucleation and stability of hydrogen bubbles within the melt. The interaction of strontium with titanium-boride grain refiners produced an even stronger change in the nucleation and stability of the bubbles formed.

Jan 1, 2002

By Ruiling DU, Jiazhi Zhang, Yong Zhao, Keng Wu

Reaction kinetics of metallurgical physical chemistry which was successfully applied in metallurgy (as ferrous metallurgy, non-ferrous metallurgy) became an important theoretical foundation for subject system of traditional metallurgy. Not only the research methods were very perfect, but also the independent structures and systems of it had been formed. One of the important tasks of metallurgical reaction engineering was the simulation of metallurgical process. And then, the mechanism of reaction process and the conversion time points of different control links should be obtained accurately. Therefore, the research methods and results of reaction kinetics in metallurgical physical chemistry were not very suitable for metallurgical reaction engineering. In order to provide the definite conditions of transmission, reaction kinetics parameters and the conversion time points of different control links for solving the transmission and reaction equations in metallurgical reaction engineering, a new method for researching kinetics mechanisms in metallurgical reaction engineering was proposed ,which was named stepwise attempt method. Then the comparison of results between the two methods and the further development of stepwise attempt method were discussed in this paper. As a new research method for reaction kinetics in metallurgical reaction engineering, stepwise attempt method could not only satisfy the development of metallurgical reaction engineering, but also provide necessary guarantees for establishing its independent subject system.

Jan 1, 2015

By Hidekazu Nakagawa

We investigated the anodic dissolution behavior of titanium in TMHA-Tf2N molten salt, which has a wide electrochemical window of about 5 V, in order to develop an electrodeposition method for titanium. By etching a titanium electrode in HF?HNO3?H3PO4 solution, the titanium electrode became electrochemically active, and a redox reaction was observed at around -0.15 V vs. I-/I3- in (TMHA-Tf2N)?HTf2N solution. We identified the redox reaction consists of the reduction of the proton and the oxidation of hydrogen. The diffusion coefficient of the proton in TMHA-Tf2N was calculated to be 6.9 10-8 cm2 s-1 at 50 °C from the cathodic peak current in the cyclic voltammogram. Anodic decomposition of the molten salt was not observed up to 6.0 V vs. I-/I3- on titanium electrode, while it was observed at around 2.0 V vs. I-/I3- on platinum and glassy carbon electrodes. Cathodic decomposition of the molten salt was observed at around -3.0 V on the titanium electrode, as well as on the platinum and glassy carbon electrode.

Jan 1, 2006