Search Documents

By James D. Navratil

Advances in hydrometallurgy require the introduction of new separation and purification processes, but they can be complex, costly and energy intensive. Chromatographic processes have low energy requirements and possess very high separation efficiencies. However, they have not yet made the great industrial impact that might be expected from their benefits. The large-scale and difficult separation of rare earths would greatly benefit from an improved continuous chromatographic operational device. Truly continuous, multicomponent chromatographic separations may be achieved by means of the continuous annular chromatograph. Work has been Initiated at The University of New South Wales involving the improvement and development of such equipment for the separation and purification of rare earths.

Jan 1, 1990

By Norihiko Fukatsu

In order to use effectively the previously reported new sensing system for hydrogen and oxygen potentials in molten copper, the criteria of the potentials for getting sound castings have been determined in the laboratory experiment. The copper melt equilibrated with a given hydrogen and an oxygen potential was rapidly quenched in the crucible. The relations between the holding potentials and the gas porosity in the solidified sample were investigated by measuring the density of the sample and microscopic observations. It was found that the defects of the gas porosity became the maximum at the potentials where the dissolved amount of hydrogen and oxygen was in the mole ratio 2: I. The samples having the density more than 99% of the theoretical value were obtained in the higher oxygen and lower hydrogen potential region or in the lower oxygen and higher hydrogen potential region. The criteria thus determined were examined by comparing with the measured potentials in the practical easting machine. In tough-pitch copper casting, the problem due to gas porosity was found to be serious when the hydrogen potential increased. In the oxygen-free copper casting, the evolution of hydrogen was found not avoided. The gas porosity in the casting, however, was found eliminated when the oxygen potential was kept at a low value.

Jan 1, 2003

By Mark Cross, Hadi Abou-Chakra, Nicholas Christakis, Mayur K. Patel, John Baxter, Ugur Tiizful

"In recent years significant effort has been put into using continuum mechanics for the description of granular flows. Although these models are partially successful in capturing some flow characteristics, they lack essential information on material properties, which are needed to account for the interactions between different particles. Thus, they are incomplete and can not be used to describe processes such as hopper filling/emptying and pneumatic conveying, where particle-particle interactions can lead to phenomena such as segregation, degradation and agglomeration. In this paper, a 3-D unstructured finite-volume framework is presented, which employs interface tracking techniques to solve for the individual material components of the granular mixture in the bulk and thus, determine the material-air interface. Various transport processes, arising from the micro-mechanical properties of the different particle species in the granular mixture, can be obtained through kinetic theory. The transport coefficients of each of the individual species can be determined and analysed in a micro-mechanical framework and the transport process parametrised in the form of constitutive models. These models provide the continuum theory with information on the micro-mechanics.This work describes the continuum framework and the micro-mechanical parametrisations, which are used to describe the processes and interactions at the microscopic level. Numerical simulations and comparisons with experimental data are then presented for the case of binary granular mixtures and conclusions are drawn on the capability of the model to realistically predict and quantify the main characteristics of granular flows."

Jan 1, 2001

By G. Scavino

A 0.5 wt.% C, 22 wt.% Mn austenitic steel, recently proposed for fabricating automotive body structures by cold sheet forming, due to favorable overall strength and ductility, exhibits plastic localizations during uniaxial tensile tests, whereas no localization happens during biaxial Erichsen cupping tests. Full-thickness tensile and Erichsen specimens, cut from as-produced sheets, were polished and tested at different strain rates. During the tensile tests, the plastic localization phenomena consist first of macroscopic deformation bands traveling along the tensile axis, and then of series of stationary deformation bands, each adjacent to the preceding ones; both types of bands involve the full specimen width and yield macroscopically observable surface relief. No comparable surface relief was observed during the standard Erichsen tests. The stress state being known to influence plastic localization phenomena, reduced-width Erichsen tests were performed with 10 to 30 mm width polished specimens, in order to explore the transition from biaxial to uniaxial loading.

Jan 1, 2009

By Eiji Iwamura

"Two types of diamond-like carbon (DLC) films with different microstructures were prepared by unbalanced magnetron sputtering, and the tribological properties of the nanoscaled DLC multilayer coatings consisting of alternating layers of graphitelike and amorphous-like microstructures were examined. The DLC microstructure was characterized by certain features of graphite-like clusters, in that some of them had onion-like structures. The films filled with the clusters were obtained in a condition with an incidence of high influx of energetic electrons, and the other films without apparent cluster structures were formed in a condition with ion bombardment controlled by negative bias voltage applied to substrates. Stacking each film layer-by-layer, the nanoscaled multilayered coatings showed superior tribological properties to individual single-layered films due to the combination of properties induced by the difference of microstructures.IntroductionIn various tribologiql applications, it is necessary for diamond like carbon (DLC) coatings to have adequate adhesion, significant hardness and a concomitant low friction coefficient. A number of deposition techniques and coating structures have been proposed to achieve suitable DLC properties [1-3]. However it is still difficult to obtain a satisfactory level of combination of the properties particularly desirable for engineering applications.In this study, the features of unbalanced magnetron sputtering were demonstrated with the effect of ion and electron bombardment. Two types of microstructures , namely amorphous-like and graphite-like, were prepared by changing the condition of the charged particles bombardment during deposition. Using the difference of properties induced by the microstructures, nanoscaled DLC multilayered structures were examined in an attempt to improve tribological properties."

Jan 1, 2000

By Shubin Wang

Copper(II) and nickel(II) are often recovered from ammoniacal alkaline solutions by solvent extraction using hydroxyoxime extractants: both copper(II) and nickel(II) are extracted from ammoniacal alkaline solutions and, from the loaded organic phase, nickel(II) is selectively stripped with a dilute acid followed by copper(II) stripping with an acid of higher concentration. Since a small portion of ammonia is co-extracted with copper and nickel, the extracted ammonia should be scrubbed using a dilute acid before metal stripping. In the present study, a mechanistic model has been developed in order to support design and control of this process. The equilibrium distribution ratios of copper(II), nickel(II), and ammonia at 298 K using LIX® 84-I (active component, 2-hydroxy-5-nonylacetophenone oxime) as the extractant are successfully correlated by considering the relevant equilibria. Based on these results, quantitative prediction of equilibrium distribution ratios in the process has been made possible, and suitable conditions for the efficient separation of copper(II) and nickel(II) are discussed.

"An experimental study has been performed to investigate the dispersed phase holdup induced by a high-strength submerged gas injection in a bottom blown air-stirred one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor using two different tuyere configurations. The air flow rates varied from 0.00599 m3/sec to 0.01312 m3/sec. In these series of experiments, water height and kerosene height were kept constant at 0.23m and 0.02m respectively. The dispersed phase holdup was determined at various gas flow rates, and tuyere orientations by using water and kerosene.The dispersed phase holdup increased with gas injection rate and decreased with vertical distance from the original interface. At constant gas flow rate, as the vertical distance increased in the centerline, off-center configuration of nozzles displayed higher values of the dispersed phase holdup than those of the center configuration. The variation of the dispersed phase holdup with the dimensionless axial distance and the gas injection rate was correlated by using the Modified Froude Number. The experimental values of the dispersed phase holdup were found to be in good agreement with the calculated values obtained from the correlation equations."

Jan 1, 1999

By M. Misra

The bacterium?Mvcobacterium Phlei has a demonstrated potential to be used for the flocculation of a variety of finely divided minerals. The microorganism possesses both hydrophobic surface and high negatively electrostatic charge. It can adhere to many mineral surfaces ?if the charge and hydrophobic interaction? between the microorganism and the minerals are favorable to adhesion. Experimental results showed that the dolomitic phosphate slime from Florida and fine hematite can be :readily flocculated from dilute suspension.. In the case of dolomitic phosphate slime, a consolidated sediment containing 24'-25 weight% :solids can be obtained from .a dilute slurry .in a short time. Sediments obtained from hematite flocculation are rather massive and more .consolidated than phosphate slime. Mycobacterium Phlei has a specificity for selective flocculation of hydrophobic fine coal particles from pyrite and ash containing minerals. Because of mutual hydrophobic interaction of coal and Mycobacterium Phlei, it was noticed that coal particles appear to be strongly held in the aggregate by adhesion or bridging of bacteria. However, Mycobacterium Phlei is not a good flocculant for either associated pyrite or ash present in coal.

Jan 1, 1991

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003

Rotary kiln incinerators are widely used in the incineration of various types of hazardous wastes. However, the complex transport processes within the incinerator are not well understood. Due to large variations in waste types and difficulties in feed characterization, the incineration process meets great challenges in a smooth operation, and expects uncertainties in the process chemistry and emission control. In order to get better understanding of the incineration process, process simulation was made on the kiln behavior by using Computational Fluid-dynamics (CFD) to characterize gas flow, temperature distribution and waste combustion in the incinerator. Temperature measurement was conducted in an operating incinerator to validate the CFD model. This paper addresses the environmental issues related to the hazardous incineration process, and reports the recent simulation results on gas flow and mixing, combustion heat transfer, and potentials to reduce emissions.

Jan 1, 2002

By Leonid N. Shekhter, Corby G. Anderson, Esra Cankaya-Yalcin, Daniel G. Gribbin, Joseph D. Lessard, Larry F. McHugh

"A new process for smelting copper, Looping Sulfide Oxidation™ (LSO™) significantly and positively alters the smelting energy balance. This process uses copper oxide in conjunction with air for the desulfurization of copper and chalcopyrite concentrates. Copper oxide is regenerated in a flash type furnace and then ""looped"" back for the oxidation of the copper concentrate. Heat and material balances show that the Looping Sulfide Oxidation™ process requires significantly lower net energy than conventional technology. This process produces anode copper and higher S02 content off-gases for efficient formation of sulfuric acid. Additionally, the process yields slags with lower copper solubility as compared to the conventional technology.IntroductionBased on the positive results from LSO™ investigations [1], further lab investigations into co=on sulfides and metal oxides were performed. It was discovered that chalcopyrite (CuFeS2) is oxidized with copper (II) oxide. In this reaction over 98.5% of sulfur was removed as S02, while a significantly improved energy balance was observed. This paper intends to analyze both the conventional flash smelting process and the newly developed Looping Sulfide Oxidation™ process, comparing heat and material balance results. LSO™ yields improvements to the energy footprint for copper, opening the door to new copper processing opportunities."

Jan 1, 2013

By Liangju He, Peixuan Ouyang, Peijie Li

Single-pulse laser ablation of aluminum and titanium alloys under glass confinement is investigated. Processing parameters such as laser intensity and gap width between targets and glass are varied. Surface morphologies and crater profiles of the alloys after laser ablation are studied by SEM and white-light interferometric microscope, respectively. The effects of gap width and laser intensity on surface morphologies and crater profiles of targets are systematically analyzed. In addition, the generation of porous surface structures in Ti target is regarded as the result of phase explosion in the molten surface layer of targets and the thermodynamic condition in our experiment for phase explosion is evaluated.

Jan 1, 2016

By Masahiro Hirasawa

"As a fundamental study on pyrometallurgical process that involves recycling steel-making dusts, of which major components are oxides of Zn and Fe, and waste polyvinyl chloride simultaneously ·at. a temperature below 1273 K, the reactions between the mixture of ZnO + Fe20 3 and PVC or the compound ZnFez04 and PVC are investigated in a series of thermogravimetric and small scale reactor experiments under inert atmosphere at below 1273 K. The reaction mechanisms are discussed· on the .basis of the thermogravimetric data. From the results of reactor experiments, it is shown that the chlorination of Zn in the oxides by Cl in PVC, the vaporization of ZnC12, the reduction of iron oxide to metal Fe by C and H in PVC, and, thereby, the separation of Zn and Fe in the oxides take place simultaneously at the temperature ~= 1200 K.IntroductionSteelmaking dusts are metallurgical wastes consisting mainly of oxides of Zn and Fe with smaller amounts of other heavy metal elements, such as Pb. In the recent investigation, [1] the present authors have investigated the fundamental aspects of a potential pyrometallurgical process· of recycling steel-making dust with polyvinyl chloride (PVC) at temperature T < 1273 K under Ar atmosphere. The performance of a similar process, in which HCl in the combustion gas of PVC is used to chlorinate Zn in the EAF dust under oxidizing atmosphere, has been investigated by Tailoka and Fray [2] with fundamental experiments. Figure 1 shows an example of the potential ·diagram of Zrt-Cl-0 and Fe-Cl-0 systems. In the figure, we can find two regions where ZnCl2(g) can be separated from Fe containing compounds. One is ZnCiz-Fe20 3 coexistence region at higher oxygen and chlorine potentials and the other is ZnCl2-Fe coexistence region at lower oxygen and chlorine potentials. The process adopted by Fray and coworkers is aimed mainly at the performance of Zn/Fe separation in the higher oxygen potential region. In the present study, the lower oxygen potential region is focused on."

Jan 1, 2000

By Frank M. Kimmerle

Spent Potlining (SPL) contains recoverable chemical elements (C, F, Na and Al) which are lost in stabilization or immobilization processes primarily aimed at eliminating cyanides and reducing leach rates of soluble fluorides prior to landfiling. They can be recovered in a variety of mineral forms for recycling in the aluminum industry and elsewhere. Alcan has developed a cost-effective hydrometallurgical route, combining a number of proven unit processes to destroy cyanides, recycle the chemical values and provide a zero-discharge process. Pilot plant studies of this Low Caustic Leach and Liming (LCL&L) Process prove that the fluoride scan be converted to acid grade fluorspar, while the sodium and aluminum are recovered as a sodium aluminate and caustic feed to the Bayer Plant operations. The remaining brick and carbon fraction constitutes a high ash solid fuel which meets TCLP leach criteria and whose reduced sodium content enhances its value as a chemical reducing agent.

Jan 1, 1994

By Liu Zhonghua

Hydrogen reduction of cobalt sulfide (Co9S8) was experimentally investigated in the temperature range 813-1053 K. The results revealed that the reaction kinetics can be described by the shrinking core mod¬el in chemical control regime at low temperatures, it is of first order with respect to hydrogen concentration, and the reaction activation energy is 67.4 kJ/mol. The SEM second electron images of the samples before and after experiments showed that the swelling of the sample above 973 K is due to the formation of metallic cobalt whiskers.

Jan 1, 1992

By A. Van den Steen

In the early fifties Professor Breckpot of the Louvain University in Belgium in collaboration with the Research Laboratory of Metallurgie Hoboken, discovered the possibility to separate nickel from cobalt sulfate solutions by a nickel sulfide depolarized cementation. This reaction, completed later with a zinc precipitation, was developed into purification processes for the Shituru and Luilu Gécamines cobalt plants in Zaíre. Due to increasing demand for higher quality products and the necessity of lowering the production costs, more laboratory and pilot plant investigations concerning the key parameters for the nickel and zinc sulfides precipitation were under- taken. Especially the relative stabilities of cobalt, nickel and zinc sulfides, precipitated with elemental sulfur or sodium hydrosulfide, were examined in relatlon with the pH and with the redox potential. These investigations have led to better plant practice and new development possibilities. The valorisation of the precipitated sulfides has also been considered.

Jan 1, 1988

By Marcela Morvová, Mário Janda, Morva Imrich

"The possibilities of greenhouse gas mitigation using various methods are brought out. The special case of utilization of mixture of CO2 with other greenhouse gases in a synergetic way inside non-thermal plasma based system is described in detail.Measurements on pilot system comprising pyrolysis chamber as alternative energy system (production of hydrogen and liquid tar) were made for various biomass and waste as the input material. The exhaust from this system was treated with non-thermal plasma gap suitable for up to 650Nm3/hour of exhaust gas flow. Condensable portion of exhaust is liquefied in distillation unit; produced hydrogen is stored on-line inside nano sized carbon of our own production.The CO2 removal efficiency varies depending on exhaust composition between 45 to 98%. Other oxides as CO, NOx, SOx and several hydrocarbons and VOC are also removed. The main product connected with CO2 removal is a solid powder of proteinoid nature. There exist strong probability, that precursor of the origin of life on the Earth from primary atmosphere were formed in the similar way as it is present in the electric discharge system used. Our system is equipped with on-line as well as ex-post analysis of all forms of products. We have also developed a system for recuperation of all forms of produced heat. It is stored inside as latent heat of waxes.IntroductionNatural greenhouse effect on the Earth is caused mainly by water vapour with the average absolute concentration about 4%. Other gases able to absorb long-wave radiation and thus this causing greenhouse effect are CO2, CH4, N2O, halocarbons and as precursors ozone and NOX. Some of them we produce and introduce into atmosphere in large quantities during production of energy and in transport. This factor leads to permanent increase of average temperature of air, sea and oceans, so called global warming.Nowadays large amount of data exists showing that the temperature of Earth in the last 150 years has been continually increasing. It represents about 03°C per ten years and the most of climatologist believe, that the increased concentration of greenhouse gases in the atmosphere is responsible for this effect.The most important greenhouse gas is carbon dioxide CO2. Majority of CO2 emissions comes from electric power stations working with fossil fuels, cars and industry. Burning of fossil fuels contribute up to 80% to world wide anthropogenetic emissions of CO2."

Jan 1, 2010

By Thomas M. Harris

Cation exchange is not sufficiently selective to be used for the removal of heavy metal ions from a general industrial wastewater. However, if the metals can be converted to polyvalent anions through complexation, they may be removed both selectively and efficiently by anion exchange. This approach, referred to as chelation-assisted anion exchange (CAAE), has been examined using industrial wastewater samples contaminated with Ni2+ and Cr3+. For this particular application, the Ni2+ is complexed with 8-hydroxyquinoline-5-sulfonic acid, and the Cr3+ with sulfosalicylic acid. Removal efficiencies and adsorption isotherms for both the complexants and the complexes were determined in batch-mode tests.

Jan 1, 1994

By P. Louis

Gécamines is the world largest cobalt producer with about 60 % of the Western World production. During the last ten years, its annual production varied from 5,400 to 14,600 t/year. The actual cobalt production capacity of Gécarnines is 18,000 t/year and could be increased in the near future if necessary. Cobalt is presently produced at the Shituru plant by an old in-pulp electrolysis process and in Luilu, by electrolysis of a clear weakly acidic solution. The Shituru Cobalt quality is lower than the Luilu one. For that reason, part of the Shituru Cobalt is fire refined and cast into granules. Large efforts have been succesfully accomplished to improve the cobalt quality. This has been made possible by a better knowledge of the purification processes and of the electrolysis parameters.

Jan 1, 1988

By R. K. Mehta

Microorganisms have been increasingly used in applications such as-metal solubillzation, precipitation and recently being used as flocculants. Optimal control and on-line monitoring of these processes occurring in microbial reactors are of extensive interest but often difficult because of the unavailability of a mechanistic model of the process and on-line direct sensors. In this paper a dynamic populatlon balance model of microbial desulfurization will be presented. The influence of certain physical and biological parameters on the leaching rate will be illustrated via computer simulations and an extended continuous-discrete Kalman filter will be Implemented for estimation of unknown states.

Jan 1, 1991