Search Documents

By Mark H. Hashiguchi

Examination of tensile bar surfaces shortly after destructive testing was conducted to search for clues that would aid in optimization of mechanical properties, especially tensile strength, yield strength and elongation to fracture. Cu-Ni-Si-Cr alloy bars in the as-cast, forged, rolled and extruded conditions were examined. Low ductility bars (<4% Elongation) showed dramatically different features than the fracture surfaces of high strength - high ductility bars (7 to 10% Elongation). Analysis of the fracture surfaces at 15X to 2000X and use of Energy-Dispersive X-Ray Spectroscopy (EDS) identified Ni-Si and Ni-Si-Cr precipitates of varying sizes and morphologies. Thermo-mechanical processing techniques to control the size and distribution of these precipitates show promise in improving the properties and performance of this alloy system and appear to correlate with improvements in the fracture surface morphology.

Jan 1, 2008

By D. Doungdeethaveeratana

The extraction kinetics in a novel solvent extraction process have been investigated. In this process, the liquid-liquid emulsion is generated by bottom gas injection into countercurrently flowing aqueous and organic phases. This process has a number of advantages over the mixer-settler unit or the spray column in terms of simple equipment configuration, without any mechanical moving parts, and the ease of cleaning and process control, while providing a sufficiently large interfacial area for rapid mass transfer. The overall rate increased with increasing gas injection rate and height of the aqueous phase but decreased with increasing injector diameter at the same gas injection rate. The variation of the overall rate constant was correlated against a set of dimensionless numbers, representing the operating conditions. Extraction rates and efficiencies comparable to those in a mechanically generated emulsion were attained in this new process.

Jan 1, 1998

By Zhijing Zhang

A thermodynamic structure model for alkali borate melts is developed to describe the distribution of structural groups in the alkali borate melts as a function of compositions. Fractions of threefold coordinated boron atoms and fourfold coordinated boron atoms in the potassium borate melt are calculated for the entire composition range and compared with results reported in the literature. The model has been used for structural interpretation for the borate anomaly in viscosity, which regards the borate anomaly as a manifestation of the various antithetical effects caused by the introduction of alkali oxide into boric oxide. It has been found that the viscosities of alkali borate melts increase or decrease according to the changes in rigidity and spatial connectivity of the glass network structure, which is a function of temperature and composition.

Jan 1, 2001

By J. D. Law

The presence of long-lived radionuclides presents a challenge to the management of radioactive wastes. Separation of the radionuclides from the waste solutions has the potential of significantly decreasing the costs associated with the immobilization and disposal of the waste by minimizing waste volumes. Several solvent extraction processes have been developed at the Idaho National Engineering and Environmental Laboratory for the separation of transuranic elements (TRUs), 90 Sr, and/or 137 Cs from acidic radioactive waste solutions. The TRUEX and POR processes for the separation of TRUs, the SREX process for the separation of 90Sr, the cobalt dicarbollide process for the separation of 137Cs and and a universal solvent extraction process for the simultaneous separation of TRUs, 90Sr, and 137Cs have all been developed in centrifugal contactors using actual liquid radioactive waste solutions and simulated dissolved calcine waste solution. In addition, the behavior of metals with each of the solvent extraction processes was evaluated. This article summarizes the most recent results of the each of the flowsheet demonstrations and provides Information on the centrifugal contactor equipment used for the testing.

Jan 1, 1999

By I. M. Richardson, M. Janssen, I. J. Bennett, V. A. Popovich

The most critical processing step during the manufacture of screen-printed crystalline solar cells is firing aluminium and silver contacts, which generates residual stresses and solar cell bowing. In this paper, an alternative Ag contact formation mechanism is proposed and aspects related to electrical contact properties, residual stresses and layer delamination are investigated. It is found that there are two main processing parameters affecting the uniformity and delamination of the Ag/Si interface, namely the peak firing temperature and the silicon surface roughness. Silicon surface polishing gives a better wetting of the silicon surface by the glass layer, resulting in a good contact and lower incidence of large voids, compared to the case of highly textured surfaces. The non-uniformity in the glass layer and large voids at the Ag/Si interface (in the case of a textured surface) are expected to have a negative effect on the mechanical strength of the solar cell.

Jan 1, 2015

By W. L. Dalmijn, J. M. Krowinkel

A recycling concept of end-of-life televisions starting with shredding will produce a complex material mixture, very heterogeneous in size, shape and degree of liberation. Basically all materials in television scrap are valuable, which means that recovery is important for either economic, environmental or sustainability reasons. However glass, plastics and metals are the materials with the highest potential for recovery. Non-magnetic materials from shredded television sets can be separated into three characteristic size fractions that need further separation for a high value-added recycling of the materials. This study investigated the potential of physical separation of these size fractions into valuable material streams using polyseparator, tlrldy current separator, dry and wet shaking tables and electrostatic separator. An overall mass balance of the mechanically processed televisions was calculated. Evaluation of the produced material fractions showed that heterogeneity in particle shape and size together with the presence of unliberated materials caused sever difficulties in separation when exclusively based on mechanical techniques. The results indicate that a certain degree of dismantling is necessary to achieve products of appropriate quality in physical separation. In order to improve recycling of electronic scrap through design for recycling cooperation between the electronics industry, the manufacturers and the recyclers of electronic goods is necessary.

Jan 1, 2000

By Yamei Han, Jiang Du, Jinhui Peng, Mengbi Fu, Libo Zhang, Zhengfu Zhang

"A continuously pilot synthesis by microwave-heating was used in preparing the cathode material LiNi113Co113Mn11302 for Li-ion battery, which used Ni1/3Co1/3Mn1/3(0H)2 and LizC03 as raw materials. Decomposition of the raw materials and synthesis of LixNi113Co113Mn11302 would be fmished in single roasting process. In addition, using microwave-heating would reduce the reacting time largely. Furthermore, the yield of LixNi1/3Co1/3Mn1/302 synthetized in single roasting process was 50 kg. Meanwhile, the effects of Li:(Ni+Co+Mn) molar radio (Li:(Ni+Co+Mn)=l.06, 1.075, 1.09, 1.15) was studied in this paper. XRD, SEM and EIS were used in characterizing the cathode material. The results showed that the best Li:(Ni+Co+Mn) molar radio was 1.075. It was found that the LiNi113Co113Mn11302 synthetized with Li:(Ni+Co+Mn)=l.075 had homogenous distribution of particles and ideal layered structure. The galvanostatic charge-discharge(O. l C, 2. 75-4.3V, vs. Lt /Li) tests showed that the initial discharge capacity of the LixNi113Co113Mn11302 was 159.5mAh·g-1, and the discharge capacity was 157.6mAh·g·1after10 cycles.IntroductionRecently, as the cobalt was expensive and the restriction of dynamic power, the commercial cathode Li2Co02 which was expensive, toxic, and high pollution had exposed its defects[1·2l. Since T.Ohzuku[3l first reported the layered LiNi113Co113Mn11302, this material had high reversible capacity and caused the attentions of researchers[4l. Its reversible capacity was l 60mAh/g and 200mAh/g in the voltage range of 2.75-4.3V[5-61. But for the present, preparing LiNiwCowMnw02 by traditional had lots of disadvantages, such as the long heating time, the high cost and the volatizing of lithium and so on[7-9l. According to these, traditional prepatation wasn't good for sustainable development and energy conservation."

Jan 1, 2013

By S. Ajima

The Naoshima Smelter and Refinery is the most important copper operation of Mitsubishi Materials Corporation. There are a Mitsubishi Continuous smelter and a conventional type of copper tankhouse. The continuous smelter with 240,000 mtpy of anode production was commissioned in May 19914 replacing two existing smelters, i.e an original Mitsubishi Process line and a conventional reverberatory furnace line. In July 1992, the copper tankhouae was expanded for the purpose to close the gap of production capacity between the smelter and the tankhouse. The cathode production capacity was increased from 13,800 to 15,800 mtpm. By these plant modifications, the distribution of minor elements was significantly changed and the impurities load is getting on increase reflecting recent shortage of clean copper concentrates supply. The paper discusses the distribution of minor elements and the impurity control strategy at the smelter end the refinery.

Jan 1, 1995

By Buket Tunçer, Mehmet Buğdaycı, Onuralp Yücel

ZrB2 and TiB2 are one of the most significant metal borides. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: Self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, TiO2, B2O3 were used as starting material and Mg used as a reductant to produce ZrB2-TiB2 powders via SHS. Therefore, it was aimed to determine production parameters, leaching conditions and comprehensive examination of final product features. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques

Jan 1, 2015

By Philip E. J. Green

Two of the cornerstones of total quality management, the use of statistical and problem solving tools, and the involvement of employees, are directly applicable to environmental protection. The reduction in variation decreases the chances of violations and mishaps. Involving employees in minimizing environmental impacts is critical. One mistake, even with the best technology, and your plant can be shut down, customers lost and fines and penalties imposed - your reputation and the environment damaged. Proven strategies for involving employees in environmental protection, and over-coming the frequently strong differences of opinions about what constitutes environmental protection, will be discussed.

Jan 1, 1992

By Musa Karakus

The sedimentary iron ores of Alsace-Lorraine, France have very high phosphorous contents that average 0.7% and are as much as 2.19% P. Ores from the Tucquegnieux and Joeuf mines have been studied by cathodoluminescence microscopy, X-ray diffraction, scanning electron microscopy, and electron microprobe analysis in order to fully characterize the mineralogy, size, shape, and distribution of the deleterious phosphate grains. The phosphorous occurs as collophane, a carbonate fluorapatite, in ten morphological forms, most abundantly as microcoprolites, but also as intraclasts, concentric layers, and cortices in ooids, phosphate replaced ooids and bioclasts, phosphatiC shells, fossil infillings and internal molds, fish teeth, phosphatiC laminae, and cements between the goethite ooids. About 95% of the phosphate grains are sufficiently large that relatively fine grinding fol&apos;lowed by reverse flotation would be expected to be effective in significantly diminishing the phosphorous content of the concentrates.

Jan 1, 1989

By Anja Pfennig, Thomas Böllinghaus, Marcus Wolf

During CCS components are exposed to a corrosive environment and mechanical stress which results in corrosion fatigue and is inevitably followed by the lifetime reduction of these components. The lifetime reduction of the cyclically loaded high alloyed stainless injectionpipe steel AISI 420C (X46Cr13, 1.4034) constantly exposed to highly corrosive CO2- saturated hot thermal water is demonstrated in in-situ-laboratory experiments (T = 60 °C, brine: Stuttgart Aquifer, flow rate: 30 l/h, CO2) in an environment similar to the on-shore CCS-site in the Northern German Bassin. In-situ tension-compression experiments were established simultaneously along with electrochemical measurements using a newly designed corrosion chamber in a resonant testing machine at a frequency as low as 30 – 40 Hz. In addition technical CO2 was introduced into the closed system at a rate close to 9 L/h. S-N plots, micrographic analysis and surface analysis of the fracture surface are demonstrated. X46Cr13 (surface roughness Rz = 4) reached the maximum number of cycles (12.5 x 106) at stress amplitude of 173 MPa producing a low scatter range of 1:3.5. Hydroxide and siderite layers were found on pits and crack surfaces. No typical fatigue limit exists. Pit corrosion prior to crack initiation may be identified as failure cause.

Jan 1, 2016

By Ruirui Wei, Yanhui Liu, Fangqing Yin, Meilong Hu

In China, Basic Oxygen Furnace (BOF) slag is traditionally used as an aggregate for civil engineering, for road engineering and fertilizer. In order to make full use of BOF slag, the experiments of BOF slag with high temperature roasting has been carried out and the phase transformation is studied. The BOF slag from Chongqing Iron & Steel is roasted in the electric muffle furnace at three different temperature. The influences of the high temperature roasting on change the phase composition of BOF slag was characterized by XRD. The results revealed that SFCA was produced at the high temperature in air atmosphere and melting temperature of slag was lowered. Therefore, if the BOF slag which treated by roasting was utilized in the sintering process, it is advantageous to improve the sintering strength and the formation of the liquid phase and reduce fuel consumption in the sintering production process.

Jan 1, 2015

By George E. Cook, Peter C. Levick, Francis M. Wells

"Relationships are established between the peak current of a pulsed, rectangular current waveform and the pulse current duty cycle under conditions of constant arc power. By appropriate choice of these interrelated parameters, it is shown that the arc pressure may be varied over a wide range even though the arc power is held constant. The methodology is suggested as a means of countering the effect of gravity in 5-G welding, while maintaining constant heat input to the weld. Combined with appropriate penetration sensors, the methodology is additionally suggested as a means of controlling penetration. IntroductionBoth low frequency pulsation (typically 0.1 - 20 Hz) and high frequency pulsation (> 100 Hz) are often used with GTA welding. Benefits derived from pulsing include improved weld quality and better process control.Advantages cited for low frequency pulsation include claims that the total heat input to the weld is reduced, the weld bead size is reduced, weld penetration is increased, grain size is reduced, porosity is reduced, weld distortion is reduced, thinner materials can be welded successfully, and the tolerance of the welding process to material and production variations is improved (1-16). With respect to the latter, pulsing aids control of weld bead penetration by increasing the tolerance to component dimensions and joint fit-up. It also reduces the sensitivity to disparities in heat sink, and it helps to reduce distortion in thin section material or distortion attributable to poor clamping. In certain materials it can reduce the sensitivity to surface oxides and to cast to cast compositional variations (16). Low frequency pulsation is also useful in welding thick materials mated by a prepared groove. In these applications the low frequency pulsation is used to obtain proper sidewall fusion as the tungsten electrode is weaved from one side of the groove to the other. In this case the weld current pulsation is synchronized with the cross seam weave pattern, such that the high current pulses occur at each sidewall. This type of low frequency pulsation has proven particularly useful in welding with narrow width groove designs (17-21). Finally, Ecer (22) has shown that the pulsed current arc is more stable against magnetic disturbances than an equivalent constant current arc."

Jan 1, 1986

By Peter R. Sanford

Cyanides are present as a dilute constituent of streams from a variety of metallurgical and mineral-processing operations. In addition, a cyanide concentration in excess of approximately 100ppb is toxic to aquatic life, and consequently these operations require a waste-treatment process to reduce the already dilute cyanide species by several orders of magnitude. Furthermore, the waste streams may have flowrates in excess of a million gallons per day. The paper reports on research conducted with a laboratory?scale electrochemical porous (graphite felt) electrode (anode) flow-reactor, which was conducted in conjunction with a computer-aided simulation of a mathematical model describing the intrinsic rate-phenomena associate with the electrode processes. The laboratory-scale cell, of rectilinear geometry, was found to be capable of reducing a feed-stream anolyte (KCN-KOH and supporting electrolyte of a single salt ? K2SO4) with a cyanide concentration of 10ppm, to less than 100ppb, at current efficiencies in the neighborhood of 50%. The computer simulation of the cell performance based on the mathematical model (and constraints imposed for tractability) was found to provide only for qualitative agreement.

Jan 1, 1998

By Derek J. Fray

"A need exists for fast and accurate analysis of species in various phases at elevated temperatures. Although modern analytical techniques are very efficient, the equipment is usually situated some distance from the industrial operation and time is spent taking the sample and sending it to the analytical facility. Several minutes can easily lapse and, during this time, heat must be supplied in order to keep the system molten and, if the composition is changing rapidly due to a refining process or reaction with the environment, the information may only be of retrospective use. Perhaps more important reasons for the use of on-line sensors are that instantaneous analysis gives better control, process optimisation and the minimisation of energy losses and pollution. To date oxygen has been the only element which is measured widely using solid electrolytes. However, the analysis of many more elements is required and possible electrolytes for other species are discussed. For some elements, ~here is no suitable conducting electrolyte and, therefore, a different approach is adopted where the electrolyte, in which one species is mobile, comes to equilibrium with another species. IntroductionThere is an ever increasing demand for the development of sensors for on-line measurements in most areas of technology and, in particular, metal processing. This is especially relevant in situations where greater control can be achieved by monitoring the chemical composition of the melt during processing and where a minor constituent in the melt can have a major effect on the properties of the finished alloy. Although modern analytical techniques are fast and reliable, the equipment due to its complexity, is frequently situated away from the process area and valuable time may be spent in sampling and transportation. During this period, heat may have to be supplied to prevent solidification and the refining reactions may be continuing, and, therefore, the analytical information may not be of direct use."

Jan 1, 1988

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Hara Prasanna Mishra

"In the Sukinda Valley of Orissa, India, the total quantity of nickel ore reserves comprising of both lateritic and chromite over burden(COB) have been estimated at around 231 million tonnes containing 0.3 to 0.9% Ni. While mining of one tonne of Chromite ore, around 6-7 tonnes of chromite over burden are removed. These overburden materials are disposed as waste materials, which causes lot of environmental hazards and ecological imbalance. India imports a large amount of nickel and ferro-nickel to meet its growing demands in various sectors. For import substitutions, efforts have been made to produced ferro-nickel from the lean deposits of nickel bearing lateritic ores/ chromite over burden materials by reduction roasting followed by magnetic separation and then the nickel rich magnetic fraction is smelted to produce ferro-nickel. It has been possible to produce ferro-nickel of grade varying from 4-25% nickel.IntroductionDuring mining of chromite ore, large quantities of overburden materials are being generated. The materials amount to approximately 10 million tones per year contain around 0.3-0.9% Ni, 0.02-0.06% Co, 20-50% Fe and 4-9% Cr2O3 depending upon the location and the depth of the mine. These materials presently do not find any application for the extraction of nickel due to lack of a suitable technology. The materials are also unsuitable for ferro-nickel making because of their very high iron to nickel ratio. The country is seriously looking for a suitable technology to utilize these resources as its entire domestic requirements of nickel is met though imports. In this connection, a systematic approach has been made at the Institute of Minerals and Materials Technology, Bhubaneswar to develop a process for ferro-nickel making from this indigenous resource."

Jan 1, 2011

By Akita Ito, Sumio Kato, Mikio Sugai, Shinichi Nakata

"Spark Plasma Sintering (SPS) is a newly developed method for the sintering of metal and ceramic powders, and completes their densification at low temperature and in short period. The SiC powder was synthesized from diatomite and graphite or carbon black by heating at 1 450°C for 1 hr in an argon atmosphere. The synthesized SiC powder was heated at 1500-1800°C, 50 MPa for 15-18 min by SPS. The relative density of sintered SiC body increased with the rise in the temperature. The oxidation of the surface of the SiC particle and impurities in SiC from diatomite greatly influenced the sintering promotion of SPS.IntroductionThe SiC has high hardness because of the covalent bonding, and is also excellent in thermal and chemical stability. However, it is difficult to obtain a dense SiC sintered body by the combustion heating-method. Therefore, the dense SiC bodies have been made by the use of additives and I or the hot pressing (HP) method.In this study, the SiC powder was synthesized by using diatomite of natural products and graphite, and carbon black of reagent as raw materials, and the relationship between the properties of SiC powders prepared at various synthetic conditions and the density of sintered body by SPS was examined."

Jan 1, 2000

MODELLING FOR DESIGN AND CONTROL AT KALGOORLIE NICKEL SMELTER Modelling at KNS has been driven by a need to have better tools to answer questions about control, design and optimisation of the plant. This paper describes a number of modelling tools developed for use at KNS and how the development of modelling tools fits with a design and control strategy. In the area of control, a thermodynamic model has been developed to allow process parameters to be calculated. The model allows for the automatic selection of data from a laboratory data base, desired operating set points are input and the operating parameters are calculated. The model has the ability to adjust the burner efficiency and the furnace heat loss depending upon conditions. To assist with the testing of proposed furnace design changes, various mathematical models of the burner and shaft have been created using PHOENICS. These models are particularly well suited to combustion heat transfer and flow aspects of both the burners and shaft. Validation of these models have been based on novel sampling and measuring techniques in the shaft and also by using scale and cold models. Overall plant energy and cost structures can be analysed using a flowsheet simulation, developed to evaluate potential alterations to the plant flowsheet. This model system allows the global evaluation of process changes.

Jan 1, 1993

By A. Treverrow, G. A. Brooks, H. K. Worner

"The work by H.K Worner and co-workers at CRA in the 1960s, and early 1970s, established that molten metals could be refined continuously utilising counter current flow of metal and slag. Womer also demonstrated that counter current refining could produce highly refined metal products. These developments coincided with the advent of high intensity metallurgical reactors in both the ferrous and non-ferrous industries (e.g. BOS, Q-BOP and later Sirosmelt) that utilised high levels of gas injection to produce rapid stirring and very fast reaction. These new generation of high intensity metallurgical reactors allowed high tonnage rates through relatively small volume vessels.Whilst, it is well known that the counter current flow of reacting phases offers the potential of efficient mass transfer and high purity products, the application of counter current reactors to molten metal/slag systems has been criticized on the basis that they suffer from either low intensity or, alternately, from poor refining due to excessive dispersion. These criticisms relate to the balance between intensity and the refining capacity of a reactor. That is, whilst high levels of mixing transversely to the direction of flow promotes high mass transfer, longitudinal mixing (dispersion) is detrimental to refining. Of course, mixing in one direction invariably leads to mixing in other directions, thus creating a playoff between high mass transfer and excessive dispersion.This balance between intensity and refining has been the subject of recent studies overseas, and at"" the University of Wollongong, using cold modelling techniques to evaluate the effect of mixing on dispersion in a counter current refining launder. These studies have shown that for a given geometry and mixing regime, dispersion decreases with increasing flow of liquid phases. This means that whilst high mass transfer cannot be achieved in a refining launder without sacrificing the degree of refinement, there is no impediment to achieving high productivity through such a system, in fact, high through puts may favour good refining. Thus, it may be possible to match a high productivity smelting operation with a equally productive counter current refining stage."

Jan 1, 1996