Search Documents

By Stephen K. Pave1

Over 1,100 tons per day of Fluid Catalytic Cracking Unit (FCCU) catalyst is used worldwide. During the cracking reaction, catalyst is contaminated by deposited metals including nickel, vanadium, potassium, copper, iron, sodium, etc. To compensate for contaminants, a portion of the circulating catalyst inventory is withdrawn for disposal and fresh catalyst is added. The DEMETR process takes spent FCCU catalyst and removes a portion of the metal contaminants, enabling the refiner to recycle demetallized catalyst, thus reducing the solid waste from the refinery. Through August, 1993, the operation of one unit for one refiner has resulted in the recycling of over 7,500 tons of spent catalyst.

Jan 1, 1994

By Chang Wei, Zhigan Deng, Minting Li, Cunxiong Li, Xingbin Li

A direct hydrometallurgical process of extraction molybdenum and nickel from molybdenum-nickel ore by pressure water leaching without reagent was studied. The extraction of Mo and Ni from molybdenum-nickel ore by oxygen pressure leaching, which exploit the characteristic of molybdenum-nickel minerals contain high concentration amorphous sulfide which has highly active, and make the most of easily oxide to sulfuric acid and sulfate at low temperature and excess oxygen presence of the amorphous sulfide. Under oxygen pressure conditions, considerable molybdenum and almost all the nickel were extracted into solution in the leaching process. The results show that with the leaching time for 3~4h, temperature at 150o C, liquid-to-solid ratio of 2mL/g, mineral granularity of 0.074mm, oxygen partial pressure of 0.4~0.5MPa without other reagent, molybdenum leaching percentage can be over 80% and nickel leaching percentage can be more than 97%. Furthermore, about 80% sulfur in the Mo-Ni ore has been transformed into sulfuric acid.

Jan 1, 2014

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. This project is concerned with the determination of the effects of operating variables on the reaction of the particles. Experiments were carried out in a large laboratory-scale flash furnace with 72 wt-% Cu matte by varying initial particle size, temperature, oxygen partial pressure, oxygen-to-matte mass ratio and residence time. Chemical analysis was used to study the oxidation extent and copper volatilization. Particle fragmentation was examined. Fractional conversion and sulfur removal slightly decreased with initial particle size, while a higher oxygen-to-matte mass ratio mainly resulted in higher fractional conversion and more efficient sulfur removal. The fractional conversion values represented the overall extent of oxidation more closely than degree of sulfur removal.

Jan 1, 1997

By R. Nilsson

In the present work, an assessment of the sulphide capacities of a number of binary and ternary slag systems have been carried out in the light of a sulphide capacity model. The model is based on the expression: {CS- exp (-A G °/R T) ? ao2 / fs2-} where AGO is the standard Gibbs energy change for the above reaction, ao2 is the activity of oxygen ions and f, is the activity coefficient of the sulphide ion in the slag. In the present model, the ratio (ao2/fs2) is optimized for the experimental data available in literature. The systems assessed are the binaries MnO-SiO2, CaO-SiO2, Al2O3-CaO, as well as the ternaries CaO-Al2O3-SiO2 and CaO-MnO-SiO2. In the case of all these systems, the experimental data available in literature were complemented by measurements carried out at the Division of Theoretical Metallurgy. The sulphide capacities of some FeO- containing binary, ternary and quaternary slags are also examined. The potentiality of the model to estimate the sulphide capacities of complex slag systems from binary and ternary data is demonstrated.

Jan 1, 1996

By J. A. Brierley

A biooxidation-heap pretreatment process was field tested to evaluate enhancing gold recovery from a preg-robbing sulfidic carbonaceous ore. Newmont Gold Company&apos;s Gold Quarry sulfidic carbonaceous ore was inoculated with an iron-grown culture of Thiobacillus ferrooxidans to form a 495 ton test heap. Biooxidation was conducted for a period of 100 days. The most active period of biooxidation occurred during the first 40 days of pretreatment? About 35 to 40% of the sulfide was oxidized. The extent of biooxidation was considered good as the ore particle size was relatively large 58% >1?9 cm (&apos;/< inch). The larger particle size ore limited the extent of bacterial activity. The field test demonstrated the ability to conduct biooxidation in a small pilot test heap. Thiourea was evaluated for extraction of gold from the biooxidized preg-robbing ore.

Jan 1, 1995

By Tapio Ahokainen, Asmo Vartiainen

"Outotec's portfolio contains a wide variety of smelting solutions for non-ferrous metals. Some of these include flash smelting for primary copper and nickel, flash converting for copper, Ausmelt technology for primary and secondary copper, nickel, tin, lead, and zinc residues and waste, Kaldo technology for secondary copper, lead, and precious metals recovery. Outotec also offers slag cleaning technologies and much more.Company provides complete process solutions tailored to each customer's individual needs. Decades of experience have resulted in extensive metallurgical know-how that ensures the most profitable process choice and optimal performance. Outotec's life cycle technology partnership with their customers spans from the early stages of process solution design through the supply and commissioning of the entire process chain. They include integrated process control and holistic service and support concepts. Continuous research and development ensures that the customer is provided with the latest advancements in process and equipment solutions.IntroductionOutotec develops and provides technology solutions for the sustainable use of the Earth's natural resources. Solutions are ranging from various processes and special equipment needed for metallurgical extraction and mineral processing of ores to the production of refined metals and minerals. The processes include not only the grinding and physical separation of ores but also the smelting and leaching of base metals and precious metals. The company provides engineering services for whole projects as well as life cycle services on the equipment and products that they supply."

Jan 1, 2012

By A. Haxhiaj, Mitovica, E. Haxhiaj

"The paper discusses problems encountered during the release and possibility of using the thermal gas quantity Mathematical models are used to calculate the positive thermal effects of the gases and losses of thermal quantity with gases in the melting process of electric furnaces. The paper discusses in details the percentages of CO, CO2, H2S, O2 and the humidity in gases and their impact on the technological process in electrical furnaces in Drenas. The paper also confers the quantity and temperature of gases, the transfer of thermal quantity and dust with gases in the environment. The paper presents the percentage of humidity in the load which is added in electric furnace for melting and its impact on thermal and environmental balance in the technological process of melting in electric furnaces. Key words: Furnace, load, temperature, humidity, gases.IntroductionNickel easily reacts with gases in the atmosphere of the furnace in which the nickel ore is processed. Such reactions can explain challenges in producing high quality nickel. Reductive atmosphere with the surrounding gases composed of sulphurous anhydrite has harmful effects on the production of nickel. This is mainly due to solubility of hydrogen as well as nickel oxide in the melted metal. Nickel reacts with carbon monoxide and forms carbide of nickel and nickel oxide which dissolve in the melted metal. Carbon monoxide also dissolves in the melted metal. The presence of carbon dioxide and water vapor in the atmosphere of the furnace impact the decrease of acidity in reductive atmosphere of the furnace. The carbon dioxide reacts with nickel and forms nickel oxide and carbon monoxide. Water vapor reacts with nickel and forms hydrogen and nickel oxide that have negative impact on the structure of nickel and its alloys. In this paper the analytical and experimental analyses are proposed that lead to minimization of the negative effects of gasses and humidity in the melting process. As the practical example, the electrical furnace in Drenas is analyzed.1. The Load and Its CompositionThe basic function of the rotational furnace is drying and reductive roasting of the ore which directly is loaded into the electrical furnace for melting. It is important to mention that the degree of roasting and pre-reduction of iron-nickel oxides is reached if the roasting process of the load in the rotational furnace is done at the temperature of 900°C to 1000°C, with the reductive atmosphere in the furnace and with minimal amount of oxygen in the processing gas. The optimal process of roasting and pre-reduction of the load in its mass is around 13 wt%. With the removal of the humidity and the sterile pare of the ore, with the positive impacts in utilization of the thermal and electrical energy in the melting process in electrical furnaces."

Jan 1, 2013

By R. Hammen

Processes are needed to rapidly and cost-effectively produce highly pure lithium salts for the rechargeable battery sector. Lithium purification is a chemical engineering challenge, due to the low concentration of lithium compared to sodium, potassium, magnesium, calcium, and transition metal ions commonly occurring in lithium brine resources. We describe a Solid Phase Extraction (SPE) process that rejects sodium and potassium, while binding lithium and other higher valent ions. Lithium is then harvested by selective displacement from the SPE column. The rapid equilibration kinetics of SPE composites enables these ion separations to occur in a small SPE column and in one column stage. The chemical parameters of the process are described.

By Niels Verbaan, Ralph Fitch, Charlotte Forstner, David Dreisinger

A process has been developed to extract gold, silver, indium, gallium, lead, copper, zinc, and other metals from a large resource using an oxidizing acid chloride heap leaching technology. The ore is crushed and/or ground to improve reactivity and then contacted with a solution containing NaCl-HCl-NaOCl. The value metals are leached into solution as chloro-complexes. The leachate is treated in a series of separation and recovery processes to produce separate saleable or disposable products. The paper will provide a summary of process development and application to a silver-indium ore from Bolivia. The possible application of the process to other ore types will be presented for discussion.

Jan 1, 2015

By Xiao Yang

Calcium oxide is one of the major fluxing agents used for steel refining. Because unreacted CaO remains in slag in most cases, discharged slag is difficult to be recycled smoothly. With the growth of environmental concerns, improving utilization efficiency of CaO is required to reduce the amount of discharged slag and energy consumption. The authors have reported a resource and energy-saving process by using multi-phase flux for dephosphorization. Reaction behavior of phosphorus in multi-phase CaO–FeOX–SiO2–P2O5 flux system was investigated. Formation mechanism of P2O5-rich phases was clarified at the interface between solid CaO or 2CaO, SiO2 and molten CaO–FeOx–SiO2–P2O5 slag. Phase relationship and thermodynamic properties of 2CaO, SiO2-3CaO, P2O5 solid solution were observed to confirm the condensation of P2O5 in solid phase. Based on these results, reduction of CaO consumption, discharged slag curtailment, and energy-saving effects in the novel refining process by using multi-phase flux were discussed.

By K. Lillkung, O. Forsen, J. Aromaa

"The dissolution rates of Pt, Pd and Rh in 250 g/L NaCl solution were calculated from the current densities determined by polarization curves and potentiostatic measurements measured with wire electrodes at atmospheric pressure. The results achieved with the two methods were similar. The dissolution rates at the corrosion potential were in the order of few nanometers per hour. The polarization curves indicated that to achieve dissolution rates required for economical operation on an industrial scale, the samples need to be polarized to higher potentials. When polarized to higher potentials, the metal dissolution rates were in the order of micrometers per hour. As the Tafel slopes of the metal dissolution region are fairly steep, the potential affects the dissolution rate greatly. Based on the activation energies, the dissolution reactions were controlled by a charge transfer step.IntroductionPlatinum group metals (PGM) have some very unique properties such as their inertness, giving excellent corrosion resistance, and a high melting point. At the same time, these factors make the refining of these metals very challenging. The main applications where PGMs are used are different catalytic converters, mostly in automotive catalysts. The used catalysts are also an attractive secondary source of PGMs. The exact concentrations of PGMs in catalysts vary widely depending on the manufacturer, the age and the capacity of the catalyst. The concentration of Pt in a new catalytic converter range from 300 to 1000 ìg/g, Pd from 200 to 800 ìg/g and Rh from 50 to 100 ìg/g [1]. Precious metal catalysts usually consist of a coat of the metal supported on ã- alumina. The recovery of metals from automotive catalysts has received much attention during the last few years [1-3]. In the near future, the use of PGMs in fuel cells is predicted to increase the amount of secondary PGMs available [4]."

Jan 1, 2012

By G. L. Hundley, D. N. Nilsen

The U.S. Department of Energy investigated the use of liquid-emulsion membranes (LEM) for the selective removal and recovery of metals such as copper and zinc from mine waste waters. This investigation included field tests of a mobile, pilot plant-scale, continuous-flow LEM system. The system was tested at copper mines with solutions containing from 100 to 1,400 ppm Cu, and at a zinc mine with a solution containing 115 ppm Zn. Typical results from the copper tests were >90% copper recovery, and zinc extraction from waste water also was typically>90%. Although all of these waste waters contained high impurity levels, pure products were produced. On several of these field tests, integrated systems were tested that resulted in recovery of metal by-products, selectiv~ precipitation of iron, and polishing to reach discharge targets for essentially all of the contained metals. In addition, some results are included from laboratory-scale tests.

Jan 1, 2000

By Susanne Pignolet-Brandom

QEM*SEM is an automated scanning electron microscope/computer system that characterizes samples with regard to mineral modal abundances, mineral grain and particle sizes, mineral associations, and particle surface areas. Additional information, based on the classification of particles according to the area percentage of a mineral of interest, can be obtained for samples of particulates. QEM*SEM is capable of analyzing a wide variety of materials although it was originally developed for applications to the minerals industry.

Jan 1, 1988

By Robert W. Hyers

Electromagnetic levitation has proven important in a wide range of experiments, all affected by fluid flow. For some experiments such as viscosity measurements, only whether the flow is laminar or turbulent must be established. For other experiments, however, quantitative assessments of velocity, shear stress, or shear strain rate are required. In most cases it is difficult or impossible to measure the internal flow in levitated droplets directly. The samples are usually small, opaque, reactive, high-temperature, metastable, or all of these. Furthermore, recirculating flow limits the utility of tracking surface particles, since they collect in stagnation points ratherthan following the flow. Most research groups have chosen mathematical modeling to assess the internal flow in levitated droplets. A variety of analytical and numerical methods have been applied, including both laminar flow and various turbulence models. A number of these models are reviewed and their impact on different containerless experiments is assessed. Much of the research reviewed here was performed by alumni of Professor Julian Szekely, and by others using similar methods.

Jan 1, 2006

By Gang Qi

The solubility of nitrogen in pure molybdenum was measured over the temperature range 2173 to 2473 K and up to one atmosphere (101 kPa) of nitrogen gas pressure. Both thermochemical and kinetic aspects of this phenomenon were considered in this study. The solution of nitrogen in molybdenum may be expressed by the reaction 1/2N2(g) = {N} (Mo,s), for which the standard Gibbs energy is given by the expression {A}G° = 78,500 + 27.36T Joules/g atom N. The formation of molybdenum nitrides, specifically Mo2N, was considered. Attention was also focused on the mechanism of nitrogen solution in molybdenum. Estimates of the diffusivity of nitrogen atoms in solid molybdenum were derived from the kinetic data.

Jan 1, 1991

By A. Kontopoulos

The extraction of nickel and cobalt from low-grade greek laterites by sulfuric acid leaching has been studied. Batch and continuous mini-plant atmospheric leaching as well as pressure leaching techniques were employed. Atmospheric leaching at temperatures as high as 95 OC generally resulted in low Ni extractions (up to 82%), high acid consumption (650-850 kg/t ore or 80-100 kg/kg Ni) and high Fe co-dissolution (30%). Pressure leaching at 260 OC increased Ni extraction to over 98%, with minimal Fe co-dissolution (2.5%); acid consumption was 300 kg/t ore (31 kg/kg Ni). Detailed experimental results and conceptual flow sheets for atmospheric and pressure leaching are presented.

Jan 1, 1991

By Saynbaatar, Gangping Ma, Jianhua Fu, Qiqige, Jinghua Wang

The influence on the performance of foam concrete made by replacing cement with some industrial waste residues was researched in this paper. The result shows that the 7d and 28d compressive strength of foam concrete increases firstly and then decreases with the increasing amount of industrial waste residue. The proper added range is 10%-20% for steel slag, blast furnace slag and coal ash, but, 8% for desulfurized fly ash. With the proper adding ratio, the compressive strength of foam concrete always increased comparing with the pure cement foam concrete. When adding 48% of the compound industrial waste residues, the 28d compressive strength of the foam concrete reached the 2.9MPa which could match the pure cement foam concrete. The results indicates that there is a synergistic effect among the compound industrial waste residue, and this effect is benefit to improving the compressive strength of foam concrete.

Jan 1, 2015

By John R. Goode

Barrick Gold Corporation operates gold mines in the United States, Chile, &apos;Peru, Canada, and in the near future, in l1anzania. Barrick meets environmental requirements and limits the potentially adverse effect of cyanide discharge to the environment using various cyanide destruction techniques. Barrick operations use, or have used, natural degradation, ferrous sulphate, hydrogen peroxide, Caro&apos;s acid, alkaline chlorination, and the SO/Air process for cyanide destruction. This paper presents a general discussion of the options for controlling cyanide in plant effluent and provides details of Barrick&apos;s operating experience including general notes on costs.

Jan 1, 1998

By Michael J. Marinigh

"Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable.In converting furnaces which have tuyères such as the Noranda Reactor and the Teniente, Peirce- Smith and Hoboken converters, efficient tuyère line management is critical to optimizing blowing rates, increasing refractory life, and improving safety.This paper will describe recent improvements made to equipment used for tuyère punching, tuyère silencing, tuyère pyrometry and refractory drilling of tuyères and how the proper application of the equipment can lead to operational and safety improvements."

Jan 1, 2009

By Katja Reinharter

Arsenic can be found in different sulfidic copper concentrates and residues, which for several years have commonly been used in copper metallurgy, as the “arsenic-free” resources are getting rare. Due to the high toxicity the removal of arsenic in the copper smelting process is a very important topic. The typical chemical slag and sulfur attack on the refractory material is getting enhanced by the presence of arsenic. This work deals with post-mortem investigations of a magnesia-chromite brick and castable used in copper smelting furnaces showing an additional and increased chemical attack by arsenic. The knowledge on the wear behaviour is not only based on a detailed chemical and mineralogical characterization, but also on thermochemical FactSageTM calculations, which are carried out on provided post-mortem samples. Post-mortem investigations on used refractory materials represent an important prerequisite for the product development, as well as for special engineered lining concepts to support our customers.