Search Documents

By Al Campoli

The majority of the 100 million roof bolts installed each year in the United States are 5/8 inch deformed rebar fully grouted into a one inch borehole. Commonly referred to as B-Series or No. 5 bar, this system is proven effective and cost efficient in coal mines with average to above average roof conditions. One of the critical variables affecting resin bolt performance is the size of the resin annulus, calculated as the difference between the hole and bolt diameters. The optimum annulus has been proven to be '/4 inch, which provides for effective mixing of the two polyester resin components and incorporation of the plastic film packaging within the cured resin. Glove fingering occurs when the plastic film is forced against the borehole wall potentially interfering with the mechanical interlock of the resin and the rock mass. Glove fingering is not a problem with the optimum '/n inch annulus but has been know to occur with the B-Series 3/8 inch annulus. Laboratory testing correlated the degree of Glove fingering with resin formulation and the bolt head to shaft axes alignment. Glove fingering occurred over 45 % of the grouted length of standard B¬Series bolts. The newly formulated Eclipse B-Series resin when combined with a 1/8 inch offset between the bolt head and shaft axes reduced the glove fingering 70%. The Eclipse system allows the 3/8 inch B-Series annulus to achieve the positive mixing characteristics associated with the / inch optimal annulus systems.

Jan 1, 2002

By M. Terry Hoch

This paper presents information on low-coal ATRS systems that are now in use. A study was conducted consisting of an in-mine evaluation of ATRS- equipped roof bolters capable of bolting in seams below 42 inches. Machine manufacturers, MSHA personnel, and bolter operators were asked to assist in reviewing the operation of various low- coal ATRS systems. Features of each system are outlined and operational problems and limitations of each are analyzed. Specific applications, such as ATRS-equipped bolters designed for use with auger-type miners, are also examined.

Jan 1, 1988

By Edward S. Custer

Recent investigations of mine roof falls have demonstrated that roof failures are generally associated with geologic conditions. The roof falls can be predicted by using the techniques of depositional modeling for the coal bed and roof rocks, and by lineament analysis. The ability to predict potential roof failure areas will allow the engineer and mine planner to develop a mine plan to avoid the roof failure areas and thus reduce overall mining costs. The ability to avoid roof failure areas also will permit maximum recovery of the coal resources.

Jan 1, 1981

By Russell C. Frith

Risk-based roadway roof support design is now a critical part of the Australian Coal Industry. Safe and efficient mining demands that roof support be tailored to the prevailing geotechnical conditions and coal mining legislation in New South Wales, Queensland, and Tasmania is clear in requiring that formalized roof support design be undertaken. The assumption of dead-load suspension of an otherwise unstable roof has been used in roadway roof support design for many years. However longevity does not necessarily translate into either a best or even reasonable practice in the current industry, particularly when pro-active strata management systems are now routinely used and reinforcing support design methods are available. The paper discusses why the assumption of dead-load suspension is fundamentally incorrect in almost all instances when pro-active or reinforcing roof support is applied and how it can easily result in misleading and potentially under-designed roof support systems under various circumstances. The commonly used design methodology of balancing the installed axial capacity of long tendons with the assumed ?weight? of a future roof fall is summarized, and several fundamental flaws are identified. The critical area of selecting the design Factor of Safety is also discussed in detail. Accepting that under certain circumstances the roof of a roadway will require it to be ?suspended?, suggestions are given for how a robust support system can be developed, designed and applied.

Jan 1, 2011

Previously, a variety of risk rating systems were used on different mines. However, these were mostly site specific and geology based systems. The purpose of developing a uniform rating system, to be used on all Anglo Coal open cast mines, is to provide an unbiased, standard and quantifiable assessment of the risk from highwall and lowwall failures. This takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and other parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all open cast mines in Anglo Coal use an almost identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. The implementation of this new system (a computer program that automatically calculates the risk) has been made as practical and easy to use as possible. Therefore, this tool can be used by personnel from other mining disciplines not directly related to rock engineering.

Jan 1, 2004

By Quanzhong Gu

Stability of a pre-exnacted recovery room plays a vital role when longwall face approaches and during a longwall face move. In an attempt to extend the application of pumpable cribs into recovery room support and to limit roof bolt installation when a longwall face approaches the recovery room, yieldable and cuttable pumpable cribs (YCPC) were employed in the recovery room at the northern West Virginia mine. The YCPC consists of two layers of materials with different strengths. This allows considerable deformation from the floor and/or roof by sacrificing the soft layer while maintaining relatively high load capacity under mining¬induced front abutment loads. The thickness and stiffness of the soft layer, installation and quality control are the key factors when using the Yieldable and Cuttable Pumpable Crib to stabilize longwall recovery room- Underground observation and monitoring results show that the Yieldable and Cuttable Pumpable Crib is a viable solution to insure stability of the recovery room and can save at least two days for a longwall face move at the mine.

Jan 1, 2004

By Tetsuro Esaki

This paper describes the present condition of mining-induced damages in Japan and the characteristics of them. The change of mining operation and environmental condition has caused various significant impacts on the ground environment: subsidence, cave-in, springing out of ground water etc. The characteristics and the influences of these phenomena are discussed by investigation of the actual conditions and by fundamental studies. Some counter measures are also introduced.

Jan 1, 1989

By Kevin MacPherson

After 34km of roof bolted drivage the first fall of ground occurred at the Phalen Colliery in the maingate of the 8th East longwall panel. The fall occurred over the stage loader as the wall approached an area of poor roof geology. This area had developed a severe cutter since initial drivage and the longwall had yet to mine through 500m of even worse conditions. This paper describes the cause of the poor roof conditions, the use of polyurethane resin injection and cable bolting to re-stabilize the roof outby the fall, and the measurement of roof movement and performance subsequent to the continuation of mining under the rehabilitated roof.

Jan 1, 1999

By John C. Stankus

In this paper, an innovative concept in longwall tailgate support is discussed. This new concept utilizes a new high capacity roof truss system in lieu of conventional wooden crib block. The first field test was conducted at Bailey Mine and was very successful. Similar tests have been installed in other mines and seams. An extensive instrumentation plan was designed and implemented in the truss test area. The test data has shown that the dynamic roof truss system effectively controls the various abutment pressures caused by longwall mining thus maintaining a stable tailgate entry.

Jan 1, 1994

By Axel Preusse

To detect improper deformations of a roof bolted roadway in order to reduce inner mine damages in the most early stage and to initiate suitable countermeasures if necessary, several different measurement systems were used for monitoring a roadway's stability on the hardcoal mine "Auguste Victoria" (DSK AG). In this paper the different convergence measurement procedures are described and their respective results are introduced. Subsequently the results of the single measurement methods and procedures are correlated with each other.

Jan 1, 2000

By David B. Plumeau

The Cayuga Mine, a deep rock salt mining, operation, changed from a standard room and pillar mine design to a yielding pillar/pressure arch design five years ago. In general the roof conditions improved. However, entries adjacent to the abutment pillars continued to fail. It was noticed that where abutment pillars were accidentally "notched" (by driving cross- cuts one cut into the pillars), the abutment entries had better roof conditions than where there were no "notches". Experiments with intentionally notched abutment pillars showed that notching did improve abutment entry conditions. During the past four years notch configuration has been varied to suit local ground conditions. Recently, "pre-cutting" of notches has proven itself as a means of protecting abutment entries under severe ground conditions. As an added bonus, the notches improve productivity by providing more places to work and reduce costs because it is not necessary to bolt the notches.

Jan 1, 1981

By Daniel W. H. Su

A floor-bearing capacity test apparatus was designed and constructed to determine the true bearing capacity of soft floor materials beneath coal pillars or longwall face supports. The apparatus has been employed in entries up to eleven feet in height. Results of in-mine floor-bearing capacity tests suggested that the ratio of the soft fireclay thickness to the bearing plate width and the moisture content in the fireclay were the most critical parameters affecting the ultimate bearing capacity. Foundation engineering principles were applied to interpret the field test results to estimate the floor-bearing capacity beneath longwall face supports.

Jan 1, 1993

By Chris Adams

The application of pre-tensioned tendon roof support assisted Harworth Colliery in their revival, from impending closure to lowest cost deep-mined producer in the UK, over just six months last year. The paper describes this success story, how it came about, the reasons "why", and the method "how"

Jan 1, 2003

By S. S. Peng

The hydraulic powered supports have been employed in U. S. longwall mining for the past two decades. Yet the sciences of roof control at the powered supported faces remain largely unknown. In order to improve longwall roof control and increase production, a series of questions in longwall roof control should be studied and answered: what is the basic rules of roof behavior in longwall coal faces equipped with the hydraulic powered supports? What is the interaction between the roof, supports, and the floor What is the contact condition of the canopy with the roof, and consequently the load distribution on the canopy? Des the periodic roof weighting really exist in the powered supported face and if so, how does it affect the face area? This paper presents the preliminary analysis of underground observations and instrumentations in a longwall panel with 4-leg shield supports designed to address the questions mentioned above.

Jan 1, 1982

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By Douglas Morrison

Hardrock mines in Ontario generally operate at between 3,000 and 7,500 ft below surface and generally experience significant rockburst activity below 5,000 ft. Since the introduction of bulk mining techniques around 1980, the safety record of Canadian hardrock mines has improved dramatically. However, the process of improvement was not a smooth one and, in the early years, the number of accidents and fatalities actually increased. One incident in 1984 that resulted in 4 fatalities in Ontario initiated a complete re-examination of mining practice and by the mid 1980s many changes had been introduced, driven by new non-prescriptive mining legislation. These changes affected not only the technical discipline of mining engineering but also the management of operational procedures and, together, they resulted in the significant improvements that have continued to this day. The analysis of the rock-fall related fatalities showed 5 major causes (loose, scaling, installing support, collapse and rockburst) and by the mid 1990s fatalities in all of these categories, except rockbursting, had been eliminated and even then, all these rockburst fatalities occurred in one mine which was closed shortly afterward. This paper discusses both the technical and social reasons for the initial failure and the ultimate success in improving the safety of these mines, with implications for mines in other major mining jurisdictions.

Jan 1, 2003

By Richard E. Thill

Two Cross-borehole systems were developed by the Bureau of Mines, one operating at a central frequency of 20 kHz for close-in spacing between boreholes (2-20m) and another operating at a dominant frequency between 1-2 kHz for more distant range (40-300+m) between boreholes. The systems are specially designed for the expected ranges and high resolution required in mining applications. Potential applications of the crosshole systems are presented for a variety of geophysical measurements related to underground mining problems.

Jan 1, 1989

By Axel Preusse

A high advance rate of the longwall face increases inevitably the mining dynamics within the rock and on the surface. Measures to limit the mining dynamics are the adjustment of the face advance rate to stretch the influences of mining over time and continuous winning to maintain a uniform influence of mining. This paper deals with the dynamics of mining subsidence within the range of a transmission overhead line for transportation of gasoline, diesel, kerosene, heating oil, mineral oil and other hydrocarbons. In a certain segment of the 24"-pipeline it was possible to predict, due to technical, operational and laying conditions, that undermining the pipeline would cause local stress maxima within the pipeline string. To limit these expected local stress maxima, the face advance rate of panel 497 was adjusted to the sensitivity of the pipeline towards the influences of mining. Comparison of the predicted mining dynamics, using the theory of stochastic media, with the measured ground movements led to the conclusion that the effects of dynamical influences which occurred within the range of the transmission overhead line and acted on it were low. This confirmed that the decision to adjust the face advance rate to the sensitivity of the transmission overhead line was correct (Kateloe et a)., 2002). A later relaxation cut in range of the pipeline siphon scarcely produced relaxation movements of the pipeline. The appointed sensitivity data of the undermined pipeline and the according maximum admissible face advance rate were thus correctly measured.

Jan 1, 2003

By Reha Ozel

The stability in longwall faces depends on the interaction beman the roof strata, face supports and floor strata. The load distribution on the other hand, depends upon relative stiffness of the three supporting elements namely, the coal face, support and gob. Therefore, in defining support requirements, it is particularly important to analyze the strata loading, the face convergence and the controlling mechanism provided by supports. The controlling mechanism however, depends on the type and characteristics of supports used in long- wall faces. The design guidelines presented in this paper have bean developed based on a number of strata control oriented projects carried out in Turkey, load and convergence measurements carried out in 10 longwall faces, in Zonguldak Coal Region, and procedures given in literature. Evaluation of load and convergence measurements, and analyses of face supports were carried out by means of a computer program, called L0NGWAI.L-MEW, developed by the authors. The output of the design analyses include the following: (1) estimation of support capacity for roof supports namely; individual hydraulic props, chock-type power supports and various types of shield supports, and (2) analysis of loading conditions and response of shield support components in terms of stability and structural integrity.

Jan 1, 1990

By Rodger Fry

All coal deposits contain anomalous geologic conditions which have an impact on roof control, Run-Of--Mine (ROM) coal quality and production costs. To remain competitive in today's coal market and provide a safe working atmosphere, mine operators need to know in advance of mining the geologic conditions which prevail in the coal deposit. In order to identify geologic anomalies within a coal seam and surrounding roof rock in advance of mining, the Radio Imaging Method (RIM) survey procedure has been developed. This paper describes the RIM procedure and how it is used to predict various geologic conditions within a coal deposit. Figure 1 illustrates the RIM in-mine and surface surveys which can be used in an underground mine. [ ] RIM is an electromagnetic (EM} wave process which consists of in-mine and surface survey techniques. Both techniques are used in underground coal mines to detect faults, interbedding, sandstone channels, and thinning coal. Thesurface survey can also be used to determine seam correlation and continuity in strip and underground mining. In-mine and surface surveys work by propagating EM waves along straight paths through the coal. As the RIM signal travels along a ray path, it interacts with the seam material and surrounding rock. This interaction causes the signal to lose energy thereby decreasing its strength along the path. The amount of energy loss per unit path length depends upon the coal seam height and type of surrounding roof and floor rock. A reading of the signal level is taken at the end of the ray path at the receiver location. This reading is used to determine the loss (attenuation) rate of the signal along the path. The signal level data is compiled and analyzed through computerized algorithms which construct images of any anomaly present. This graphical depiction of the coal provides a basis for further geologic interpretation. By comparing the images reconstructed by the RIM analysis to in-mine geologic mappings made while mining through RIM study zones, it has been confirmed that RIM can help detect the following; Rapidly Thinning Coal Incompetent Roof Rock Poor Floor Lithology

Jan 1, 1984