Search Documents

By D. Shin

The gold leaching using cyanide from ore or waste has been almost universally in use [1]. Recently, biological gold bioleaching using cyanide producing bacteria, e.g. Chromobacterium violaceum, Pseudomonas fluorescens, or P. aeruginosa, has been investigated as environmental friendly and cost effective method. Among them, C. violaceum has been reported as effective cyanide producing bacterium on gold leaching [2, 3]. C. violaceum produces cyanide using glycine as a direct precursor and subsequently detoxify the cyanide by ß-cyanoalanine synthase [4]. However, until today only 0.026 ? 16.9 mg/L of cyanide production in YP medium has been reported in the literatures by C. violaceum [4-6]. Comparing with adding cyanide chemical, biogenic cyanide concentration is lower than the cyanide concentration added in traditional cyanidation. Since cyanide also forms complexes with a number of other elements such as iron, nickel, zinc, silver, copper, and platinum, it is very important for gold recovery to investigate the enhancement of biological cyanide production and set optimal experimental condition. Most of early studies on gold bioleaching by C. violaceum have been performed to investigate gold leaching mechanism using gold powder, and recently various resources such as ores, electronic scrap, and printed circuit boards of waste electronics [7]. Few studies have dealt with gold bioleaching from low-grade ore. In this research the feasibility of gold bioleaching by C. violaceum from low-grade ores containing gold was evaluated and fundamental study was performed for further scale-up study. The aim of this study was to improve the potential of gold bioleaching by C. violaceum from gold-containing ore; in particular, enhancement of biological cyanide production.

Jan 1, 2012

By None None

Life as a mining/mineral professional doesn’t leave much time for perusing 20-page technical papers. Yet, being technologically savvy is part and parcel of a successful career in this industry. What’s an intelligent, well-informed person to do?

By John Corcoran

INTRODUCTION Content of this Report The 1300m long twin-bore 8.1m diameter Airside Road Tunnels (ART) were excavated beneath the busy taxiways and stands of Heathrow Airport between 2002and 2003. The tunnels were fully completed and handed over to the client for use early in 2005. This paper will describe the purpose of the tunnels, and the measures put in place to minimize the impact of construction on the daily activities involved in running an international airport. Terminal 5 Construction Heathrow Airport is the busiest international airport in the World, with a current capacity of circa 67 million passengers per year, based on existing infrastructure of4 passenger terminals, 1 cargo terminal, 2 runways and 170 aircraft stands. Terminal 5(T5) is being built to increase Heathrow’s passenger capacity by providing the following: 12 additional aircraft stands through redevelopment of the south apron area, in the autumn of 2004 A main terminal building (T5A) and a first satellite (T5B), and 43 additional stands by the spring of 2008, most of which will be able to receive the new generation large aircraft (Airbus A380) A second optional satellite (T5C) by year 2010 A third optional satellite (T5D) by year 2015 The total value of the project is approximately 4.2 billion pounds for the main phase of the works spanning from 2000 to 2007. Purpose of the Airside Road Tunnel The ART has been constructed to support the internal road traffic of the airport between terminals, aircraft stands, runways and taxiways, for passenger buses, service and technical vehicles. The majority of the traffic will be buses transporting passengers between the terminals and their aircraft.

Jan 1, 2005

By Zephaniah Varley, Satoshi Akai, Richard Sage, Steve Redmond, Mike Murray, Rohit Shetty, Gerald Skalla

One would be hard pressed to find another project as complex as this one given its configuration, the variety of issues to address and the required construction techniques. Contract C710 is currently under construction as part of Sound Transit’s Link Light Rail, connecting downtown Seattle with Sea-Tac Airport. The paper describes the construction-to-date of the deep mined station under Beacon Hill using the Sequential Excavation Method (SEM). This deep “binocular” station is being mined through some of the most challenging soft ground conditions in the USA. The excavated volume of the station is approximately 60,000 cy (46,000 m3) and the station comprises a variety of geometries and cross sections ranging from 235 sf (22 m2) up to 1,670 sf (155 m2). This underground complex includes platform, concourse, cross-passage and emergency ventilation tunnels together with station egress and ventilation shafts. Various excavation sequences are in use for the different tunnels including the twin-sidewall drifts for the impressive45 ft (13.7 m) wide by 42 ft ( 12.8 m) high concourse cross adits. This station has two train platforms approximately 165 feet (50m) below the surface. This station, constructed in highly variable glacial deposits including water bearing sands and silts approximately 50 ft below multiple perched water tables in an urban setting, creates a very unique and challenging situation. The ground is being managed with various types of ground improvements such as jet grouting and vacuum assisted deep dewatering wells from the surface, and from underground by use of “SEM Tool-box Items” such as barrel vault canopy, grouted pipe and rebar spiling, chemical grout,

Jan 1, 2007

By Jill Murray

This study focuses on the amosite mining region in South Africa and associated health effects, compared to other mined asbestos fiber types. Historically, dust and fiber levels were high in the amosite mills and mines, and many miners and members of the surrounding communities were exposed to the fibers. Research has shown that amosite produces both benign and malignant disease. Nevertheless, the mesotheliomagenic potential of amosite is several fold lower than crocidolite. The risk of disease associated with amosite exposure is difficult to quantify. Reasons for this include the scarcity of available information, including fiber measurements, and case ascertainment, as well as the juxtaposition of the amosite and crocidolite asbestos seams in South Africa. © 2007 Elsevier Inc. All rights reserved. Keywords: Amosite; Mesothelioma; Crocidolite; South Africa; Asbestos

Jan 1, 2007

By W. P. Arnott

This paper presents real time photoacoustic measurements of diesel-soot black-carbon (BC or EC) and Dusttrak nephelometer total carbon (TC) concentrations in a Nevada gold mine. Comparisons with time-integrated filter-based measurements of EC and TC accomplished using the NIOSH 5040 method were found to be 50% smaller than the integrated real time measurements. This work was initiated primarily as a demonstration project for the usefulness of photoacoustic instruments in measuring BC in the mine environment. Real time black carbon measurements are very useful for determining miner exposure, for providing feedback in mine ventilation systems, and for quantifying machine specific emission rates to understand the operating conditions for specific machines that produce greatest black carbon concentrations. This paper reports real time measurements of DPM from a loaded and empty hauler as it is operated in a drift with a 12% grade. The photoacoustic instruments were demonstrated to be satisfactory for BC measurements in the mine environment.

Jan 1, 2009

By K. A. Lewandowski

The efficiency of heap leaching is reduced by poor solution flow characteristics (i.e., channeling and ponding) that result from fines migration. Agglomeration of the ore can immobilize fines, but for agglomeration to be successful in copper leaching, an acid-resistant binder is needed to stabilize the agglomerates. Until now, there has not been a satisfactory method to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? This paper reports on several procedures that have been developed to quantitatively determine whether a binder gives good performance in an acidic solution. These procedures have been used to identify binders that would be suitable for copper heap leaching.

Jan 1, 2008

By S. Schina

Part of the Imittos Western Peripheral Motorway in Athens is the twin road tunnel in the vicinity of American College, with 20m excavation diameter. In the paper, the environmental and other requirements, the geometry and the geological – geotechnical characteristics of the rock formations in the construction area are given. Information regarding the modeling and analysis methods that are used for the design of the temporary support, the final lining and the wedge and slope stability analysis is described thoroughly. Finally, the results of the analyses are compared with these of measurements and general remarks during the construction of the tunnels.

Jan 1, 2001

By Allan Sylvester, Paul E. Gabryszak, Diane R. Hirsch, David P. Field

With construction of the first phase of the Automated People Mover (APM) Tunnels nearing completion, this paper will address how knowledge from recent Tunnel Boring Machine (TBM) and New Austrian Tunneling Method (NATM) tunnel construction at the airport was used to refine the methodology for the next phase of tunnels currently in design. The benefits include an enhanced understanding of the ground conditions; allowing optimization of excavation sequences and support requirements; a more effective instrumentation and monitoring program; and improved construction details and related contract provisions.

Jan 1, 2007

By S. Underwood

The tracer gas method of conducting ventilation surveys is a means of determining air quantity in underground mines with knowledge of the concentration of the tracer in the atmosphere and the flow rate at which the tracer is being released. The technique is useful in inaccessible areas of underground mines and areas where traditional point measurement of velocity is not practical. Sulfur hexafluoride (SF6) is the industry standard tracer(Kennedy 1987) used in underground mines because it is safe, stable, and not naturally occurring in the mine environment. The implementation of a second tracer will increase the versatility of the tracer gas technique allowing for simultaneous releases for the study of interrelated ventilation circuits, and for conducting multiple experiments in less time. This paper will detail the selection of perfluoromethylcyclohexane (PMCH) as a novel tracer with sensitivity, physical properties, and analysis characteristics similar to SF6. Methods for the release of liquid PMCH into underground mines will be recommended, and the vulnerabilities of sample loss due to condensation of vapor PMCH will be explored. Finally, the benefits and implications of using PMCH as a second tracer will be discussed.

Jan 1, 2012

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009

By S. J. Boone, A. Poschmann, C. Pound, A. Pace

San Diego’s Stadium Conglomerate consists of poorly cemented cobbles, gravel, sand, silt and clay. Conventional laboratory and in-situ testing is not suitable for characterizing its engineering properties. Although the formation is often considered a “rock” its behavior is more readily modeled using soil mechanics. Static and seismic design of a tunnel for the Mission Valley East light rail extension required that the stress-strain characteristics of the ground be identified over a broad strain range. Geophysical methods and field plate load testing were used to develop a full non-linear stress-strain model of the expected ground behavior. Quantification of the coarse material distribution was also required for selection of tunneling methods and construction considerations.

Jan 1, 2001

By R. Larry Grayson, Ahmet Unal

Use of radio frequency identification (RFID) technology to solve informational needs in isolated and restricted underground mining environments will be reviewed, giving specifications of some past and currently available systems. The advantages and disadvantages of using various frequencies, system configurations, and specific components, including their construction standards and capability, will be discussed. The remaining challenges to more widespread use of RFID systems for personnel and vehicle tracking will be identified, and recommendations concerning operating environment capabilities will be detailed. Finally, the ultimate requirements for maintaining system integrity during and following a coal mine emergency will be discussed.

Feb 24, 1997

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By R. L. Hudak, R. F. Randolph, A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. The National Institute of Occupational Safety and Health (NIOSH) has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by nine decibels. The “Inquiring Ears Want to Know” fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By Steve Kral

The mining industry in Colorado faces the same problems the industry faces throughout the United States and the world — record low commodity prices and increasing regulatory and environmental restrictions that seemed designed to curtail mining activities. Despite those obstacles, the mining industry in Colorado still contributes about $8 billion annually to the state’s economy in the form of base and precious metals, industrial minerals, coal and associated service businesses and jobs. So the 300 attendees at the102nd National Western Mining Conference felt reason-ably positive about the industry in their state. The meeting is the Colorado Mining Association’s annual conference and was held at the Broadmoor Hotel in Colorado Springs in November. The theme was “Mining in the New Millennium — Achievement + Innovation = Survival.” Experts from Colorado’s mining industry and abroad discussed the challenges faced by the mining industry as it enters the new millennium. They offered insights into how the industry will operate during the early years of the 21st century and how it will survive low prices and increased regulatory restrictions.

Jan 1, 2000

By J. M. Dean, R. L. Grayson, R. C. Althouse, M. J. Klishis, G. L. Winn

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Feb 24, 1997

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

By Kevin Andrews, Terry Hamric, Scott Nelson

"Mining conditions in underground coal mines are dictated by the environment in which the coal seams were geologically deposited. Depositional features can change rapidly, significantly affecting mining conditions. Mine geologists understand factors affecting mining conditions, predict future conditions, and provide guidance to mine management. A case study demonstrates how a mine in Appalachia merged an understanding of depositional environments with mining conditions and drilling data to make informed decisions as the mine encountered geologic anomalies. The assessment included drilling, mapping of geologic hazards and mine productivity, and creation of a conceptual depositional model. Metallurgical coal quality and clean tons per foot served as incentives for continued advance. Mining in the south was historically favorable, with good production and advance rates. As mining advanced north, changing geologic conditions caused the upper seam split to abruptly disappear. The mine ramped down into the lower seam split. Mining in the north area encountered unfavorable conditions, including transition roof, “horsebacks,” sandstone intrusions, roof rolls, and bony floor, resulting in low rates of mining advance. The mine geologist characterized the features and created a predictive model for future mining. Most of the adverse conditions were attributed to the coal in the north being part of an incised, transgressive valley fill environment, as compared to the favorable conditions in the south resulting from a floodplain depositional environment. Geologic conditions, low productivity, and unfavorable future predicted conditions in the north ultimately resulted in mine closure and reallocation of resources to a new mine with better forecasted conditions.INTRODUCTIONThe role of a geologist in assisting coal mining operations to understand and predict the impact of varying geological factors on mining productivity is a critical one, especially when management decisions must be made about the future prospects of a mine operating in difficult conditions. Chase, Newman, and Rusnak (2006) provide a very thorough discussion of the evolution of the role of the coal mine geologist and emphasizes the importance of understanding geology with regard to mine management decisions. Using actual mining performance data to determine which geologic factors are the most critical for mining is a powerful tool for making informed mine management decisions. For example, Nelson, Mullennex, and Miller (1988) provide a case study of analyzing the geologic factors impacting productivity of a Kentucky longwall mine to predict future mining conditions for the operation. In that case, the difficult geologic factors for longwall mining were prevalent across much of the remaining permit area and, in response, mine management converted the operation from a longwall operation to a continuous miner (CM) operation to better adapt to the geology. In another example, Keim and Miller (1999) evaluated geologic conditions impacting a West Virginia longwall mine. In both examples, significant geotechnical and geological information was available, including the opportunity to compare predicted mining conditions against actual conditions as mining progressed. Numerous examples of advanced Geologic Hazard Mapping (GHM) methodologies have come from government agencies and academia. For example, development of the Coal Mine Roof Rating (CMRR) system (Molinda and Mark, 1994) provided a standard means for geologists and engineers to communicate quantitatively with regard to mine roof conditions, and the introduction of the Stability Mapping System (SMS) provided an efficient means for analyzing numerous factors affecting coal mine stability (Wang and Heasley, 2005)."

Jan 1, 2019

By J. Leinart

As is readily apparent, the reliability of the early-stage costs estimated for any mining project are critical to the viability of that project. An estimate too high might leave a potentially profitable deposit undeveloped or worse yet, available to a competitor. One too low might waste investment dollars in a project not yet economically ripe. There are two aspects critical to any estimate: 1. The cost data used to represent the values of the wages, salaries, supplies, and equipment. 2. The design used to determine the engineering parameters upon which the above estimated values are based. Given that all of the information contained in Mining Cost Service is provided by suppliers, equipment manufacturers and mine operators, one wonders why there is any question as to the reliability of cost estimates developed using this information. Given that it is all actual (as opposed to statistically derived) data, where do the problems with estimate reliability lie and what is the impact of the data on that reliability? The following presents a series of analyses designed to assess the reliability of the cost estimating process. Both the actual cost data and the engineering parameters upon which they are based are examined in an attempt to quantify and understand the importance of each. While several sources of cost information are available (Means, Richardson, Primedia?s Equipment Watch, and individual suppliers and manufacturers), the following rely solely on data contained in InfoMine USA, Inc?s, Mining Cost Service and in its Sherpa Mine Cost Estimating Software.

Feb 27, 2013