Search Documents

By Stephen Meyer, Véronique Falmagne, Antti Pyy

Kittilä Mine is a gold mine located in Northern Finland, owned and operated by Agnico Eagle Finland. The mining operation started in 2008 with open pits which were completed in 2012 and production moved to being entirely underground. The mine consists of four separate orebodies, currently producing 2.0 Mt per annum, and requiring over 19 km of development on a yearly basis. The principal mining method is long hole stoping with delayed backfill. Microseismic monitoring was initially tested in the Suuri orebody, in the mining block between the 625 and 500 Levels. A small monitoring system was installed in 2018, after observations of stress-induced damage to the rock mass and in anticipation of future mining at greater depth. The initial goals were to evaluate if useful data could be recorded and test the signal quality of different sensor types. Prior to 2018, ground control related challenges in the Suuri and Roura mining blocks had been mostly related to sill pillar mining and block movements between weak graphitic schist planes. Seismic monitoring in the Suuri deposit proved successful for following the rock mass response to mining and helped support the rationale for early monitoring in the new, deeper mining block in Rimpi at 900 m depth. Preliminary geotechnical characterization and testing of the rock mass showed areas of silicification in the footwall rocks with potentially continuous structural features. Seismic monitoring of the Rimpi area has confirmed the brittle behavior of the rock mass, with strong seismic responses induced by stress changes following blasting being recorded. In addition to this expected behavior, a large magnitude event associated with significant damage in the footwall drive development 90 m above the stoping was experienced. Initial investigation of the rockburst showed two separate damage locations with over 300 tons of displaced rock. The seismic monitoring system recorded this rockburst as a single seismic event with magnitude significantly larger than previously recorded. Additional analyses indicated a possible thrust fault event, triggering two separate strainbursts. Following this event, the ground support system was upgraded in parts of the footwall drives to improve dynamic capacity. Systematic calculation of the source mechanisms for the small footwall events down to Mw-2.5 has revealed potential planar structures in the footwall. Early implementation of microseismic

Apr 26, 2022

By Michael G. Zabetakis

Effective accident prevention programs utilize a broad spectrum of activities, including meaningful training programs. In practice, such programs must be directed towards specific, defined needs. These needs are considered here for three categories of employees: new, re-assigned, and experienced.

Jan 1, 1983

By D. M. Steelman

Digital systems have been employed in industry as an aid in process evaluation and control for about 20 years. The earlier systems were quite simple and did little more than periodically scan a multitude of process variables, perhaps comparing them to alarm limits, and print out the results. As time passed, the needs of industry and the imagination of process engineers became more demanding. Rather than perform only alarm checking and logging, operating guides were generated to help the operator gain optimum performance from the process. Eventually, systems were entrusted with the job of manipulating the set points of the local analog control loops in a (DDAC) digitally directed analog control mode. Today digital systems are used to gather all-the process information, including both analog and digital variables; to make the necessary data manipulations; and to control the process end elements in a (DDC) direct digital control mode. During these years of transition from the very simplest systems to the complex systems of today, the demands upon the system engineer have been every increasing. The process engineer has required, among other things, more computational ability at high speeds, faster input and output rates, greater flexibility, better communication facilities (man-machine interface), (process oriented software), and finally, greater reliability at lower cost.

Jan 1, 1969

By R. A. Pimentel

Many longwall operators experience difficulty complying with the federal regulation limiting average dust exposure. Others are currently in compliance, but the dust exposure limit keeps then from increasing their production. Spray water is a major means of dust control. Excess water can cause problems in the transportation system and the cleaning plant, and reduces the Btu value of the run of mine coal. Thus, the dust exposure reduction per unit of water sprayed must be maximized. This paper discusses underground tests recently completed as part of a Bureau of Mines research program to determine the effects of variations in spray water flow rate, pressure, proportioning and spray orientation on longwall shearers.

Jan 1, 1984

By George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95.9.5.5 mt (105.770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/ml (0.36 oz/st) silver with 0.94 % copper. 1.10 a lead and 11.06% zinc. Ore reserves at El Roble are estimated as 1.1% Mmt (1.21 million st) grading 4.89% copper and 3.39 g/mt (0.099 oz/st) ,old. Geologically possible reserves at Equis may total 1.6.Mmt (1.76 million it). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1984

By Carl G. Consalus

The Kemmerer Coal Company's Sorensen Mine is located approximately 7 miles Southwest of the Town of Kemmerer, Lincoln County, Wyoming. The coal it produces is delivered via conveyor directly to Utah Power and Light's Naughton Steam Generating Plant. The Plant went on the line in the spring of 1963 and the Sorensen Mine has been producing coal since February of that year. In this period, approximately 2, 000, 000 tons of coal have been delivered to the Plant. Present Sorensen mining operations are being carried out in the upper seams of the Adaville Formation. The formation contains, in some places, up to 30 coal seams of varying quality and thickness. Thirteen seams are considered major and are given numbers; the rest are considered splits off of the major seams and are so named. The lowest seam stratigraphically is the No. 1, or Elkol seam. So far, it has not been committed to power production but is being held in- reserve. It is the thickest seam with 80-90 feet of coal as its average thickness. The other major seams vary from 10-50 feet thick, with most of the seams averaging 17-26 feet of thickness. Each major seam has been opened at least once' to obtain a true gross sample of the coal's performance in the Plant.

Jan 1, 1967

By Andres Salazar, Carlos Delgado Robles, Richard K. Preece

The paper discusses the evolution of the geometallurgical model at the Escondida mine in northern Chile, the world’s largest copper producer. It highlights the transition from early metallurgical forecasting methods to a comprehensive model that includes spatial distribution of metallurgical forecasts. This model helps in planning and adapting to the variability in ore characteristics, such as hardness and mineralogy, which affect processing performance.

Dec 1, 2023

By O. H. Rostad

The importance of geology in ore reserve estimation has been stated by several authors. King et, a1 (1982) reported that the geological factor was the key deficiency where serious weaknesses in ore reserve estimation appeared, especially in grade. The foundation for a successful mining operation is an ore reserve estimate that neither overstates nor understates the true situation as to tonnage and grade. Overestimation of reserves can have devastating economic results. Overestimation of tonnage may lead to wasting money on an overbuilt plant or worse yet, if grade is seriously overestimated also, to undertaking an operation that is doomed to economic failure from the outset. Understated ore reserves can result in building a plant that is smaller than optimum which may result in higher unit costs. At worst, understated tonnage of ore reserves can result in a missed opportunity for a profitable operation. Failure of the ore reserve estimator to properly take into account all geologic and allied factors pertaining to the deposit can result in an ore reserve estimate that is overstated either as to tonnage or grade or both. This paper will focus on these factors and will not discuss rules about distances above or below a drift that should be given a classification of proven or probable, etc. Each deposit has its own particular characteristics which often require modification of general rules for defining limits of proven and probable ore blocks that work satisfactorily in another deposit. A number of references are included which discuss some of these problems. Definitions of ore reserve classifications and an illustration are given in the Appendix.

Jan 1, 1985

By Sihua Lei, Hong Zhong, Shuai Wang, Yu Gan, Zhanfang Cao

High purity MgO is widely used in various fields as an important magnesiumcompound. The separation of Mg and Ca is of great importance for the preparation of high purity MgO from dolomite. In this study, the key effects of carbonization temperature and nano-calcium carbonate agglomeration on the separation mechanism of calcium and magnesium have been investigated. The results indicated that the reaction in the carbonization process was stepwise. Precise control of the carbonization temperature was essential for the formation of Mg(HCO3)2 due to its low reaction efficiency at lower temperatures or decomposition markedly at higher temperatures. Meanwhile, there was a common-ion effect in solutions containing Mg2+ and Ca2+. Nano-CaCO3 particles were formed during carbonization and agglomerated with the prolongation of static time. A product with a purity of 99.56% MgO and 0.16% CaO was obtained under the optimized conditions: ratio of liquid–solid 30 L/g, carbonization temperature 22–25 °C, carbonization time 1 h, and refining time 4 h. This work has important guiding significance for the preparation of high purity magnesium oxide from dolomite.

Apr 21, 2020

By Zoheir Khademian, Gabriel S. Esterhuizen, Morgan Sears

Based on the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accident in the US longwall mines were caused by gateroad roof instability. This can be related to the significant changes in loading conditions that gateroads are subject to from the development to the longwall abutment loading phases, combined with the thinly bedded shale roof, found in many US longwall coal mines. One of the challenges in designing efficient support systems is to understand the roof instability mechanisms along with support-roof interactions under this complex loading condition. Field monitoring of roof displacement and stress changes coupled with detailed analyses using numerical models are well-documented techniques to study the causes of roof instabilities. However, traditional modeling techniques require additional calibration to simulate delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. One alternative modeling technique is the UDEC Bonded Block Method (BBM) where bedded roof and support interactions can be explicitly captured. This paper presents the development of a BBM model of a longwall entry at a 180 m depth of cover with a three-entry gateroad layout along with roof extensometer monitoring results. The models are validated against the monitoring data, showing the potential for BBM numerical models capturing the complex roof and support system interactions to assist with optimizing gateroad layouts and support systems.

By Furuyama Takashi, Mori Sukeyuki, Hara Tsuyoshi, Fukushima Yujin

In mineral processing practice, flocculation is largely established as an engineering technique of waste water treatment and the study of parameters increasing the settling velocity of particles is still of great importance to improve the process. Further investigations were made using quartz (Q89) and fluorite samples (F91) which included 58.8% and 65.8% of -2.3 µm particles respectively. In all the experiments the flocculation phenomena were observed varying the pH value of the aqueous suspension. In contrast to quartz particles (Q89) which did not flocculate for all pH values, it was, noticed that fluorite particles (F91) flocculated in the alkaline range of pH over 11. With an aqueous suspension containing equal quantities of Q89 and F91, a hetero-flocculation of particles was observed at a range of pH below 10. In this case, the maximum floc size of the hetero-flocculation was 37.0-26.2 µm This size was about three times larger than when quartz (Q84) and fluorite particles (F85) were used with 32.4% and 40.4% of -2.31 µm particles respectively. Besides, in the experiments using Q89 and F91, the maximum size of hetero-flocculated single particles was found to be 6.54 µm instead of 3.27 µm as obtained with Q84 and F85.

Jan 1, 1995

By Raj K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. Canadian open-pit mines are highly mechanized and use state-of-the-art equipment and support technology. During the past few years, productivity improvements at Canadian open-pit mines have been achieved by taking advantage of larger equipment, in-pit crushing and conveying, truck dispatch systems and electronic management tools. The most recent developments are related to hydraulic transportation and the application of global positioning systems (GPS). Mine planning has become computerized. Environmental issues are dealt with in all phases of planning. Equipment modifications are pursued with vigor to keep the equipment functioning in the hostile Canadian north. In 1997, the mining and mineral processing sector employed 370,000 Canadians, contributing $26.2 billion to Canada's gross domestic product (GDP). The value of production of the Canadian mineral industry, including coal, amounted to $19.1 billion in 1997. Gold remained Canada's leading mineral with production valued at $2.8 billion. This was followed by copper ($2 billion), coal ($1.9 billion), zinc ($1.6 billion) and nickel ($1.9 billion). [ ] Synthetic crude oil from oil-sands mining operations in Alberta represents an important part of Canada's petroleum production. In 1997, the value of synthetic oil production was $2.87 billion. Canadian oil-sands mining has contributed significant technology developments in Canada.

Jan 1, 1999

By Perry M. Jones

An important operational and environ-mental concern associated with in situ leaching activity is the balance between solution injection and recovery. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. The Bureau of Mines is investigating the factors that affect solution balance in an unsaturated ore deposit, as part of ongoing in situ leaching hydrologic investigations at the Cyprus Casa Grande Mine. Flow conditions in 58 injection and recovery wells at the Casa Grande In Situ Leaching Test Facility were monitored daily over an 18 month period. Changes in the balance between injection and recovery occurring during this period were evaluated using analytical and statistical methods. The results permit estimation of solution distribution and the volume of solution stored in microfractures and interstitial pore spaces within the deposit following 18 months of leaching. Approximately half of the difference between well injection and well recovery can be accounted for by solution movement through macrofractures into nearby drifts. Estimates of solution storage within the ore deposit at the end of 18 months of leaching range from 3.5 to 6.9 pet. of injected solution. These results also suggest that 13 to 26 pet. of the fracture/interstitial pore space in the deposit was saturated with solution after 18 months of leaching.

Jan 1, 1991

By David Maust, Rob Albinger, Mike Walling, Michael Rispin

The safeguarding of health and life is the number one priority for underground infrastructure projects. While culture and approach are critically important, the industry has also seen the development of innovative tools and technologies that assist in making the underground environment and working places more safe and secure, both on an everyday basis and in the event of an unexpected occurrence.

Dec 1, 2022

By R. A. Wyman

"The froth flotation process was patented by E.L. Sulman, H.F.K. Pickard, and John Ballot in 1906 . . . . . . . . . .James M. Hyde installed the first froth flotation process in the U.S., about August 1, 1911, at the Basin Reduction Co. plant, Basin, Montana . . . . . . . . . .By 1914, 42 mining companies were operating or experimenting with the flotation process . . . . . . . . . .The period 1930 to 1960 saw the application of flotation spread to nonsulphide ores and become the key factor in the economic production of many industrial minerals". So states FROTH FLOTATION, 50th Anniversary Volume, published by AIME in 1962. It is interesting, to observe that the Mines Branch, now part of the Canadian Department of Energy, Mines and Resources, was established in 1907 through an act of Parliament entitled, "The Nines and Geology Act". In 1911, a mineral dressing group was formed and a laboratory was constructed. By 1921, an engineer was devoting full time to industrial mineral processing problems.

Jan 1, 1971

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By R. Thorpe, M. Dosbaba, A. Kopriva, A. Niiranen, J. Ruokanen

"Automated Mineralogy (AM) is an important diagnostic tool in flotation plants as it adds ore and particle mineralogical properties to traditional mass and chemical data. AM is used in project development, for future ore studies and for diagnosing concentrator operations. With the exception of operations who own central laboratory or on-site systems, the use of AM is often limited to the analysis of a comparatively small set of samples. Metrix Plant Technologies has partnered with TESCAN to integrate TIMA AM technology into the implementation of Performance Assessment Campaigns (PAC). Routine daily composite samples from the mill are analysed mineralogically on a size-by-size basis over several weeks. All the relevant metallurgical, process control and mineralogical data is combined into a single large database for mass balancing and interactive examination. This paper describes the implementation and results of a PAC at the Agnico Eagle Kittilä gold mine in Finland. Although challenging, the addition of mineralogical data as dependent variables in multivariate analysis leads to a much deeper understanding of the root cause effect of events driving the flotation performance. INTRODUCTION TO STUDY The Kittilä mine, owned by Agnico Eagle, is Europe’s largest primary gold mine, with annual production of approximately 180,000 Oz. The operation is located in Lapland in northern Finland, and is currently expected to operate until 2035. The location of the operation is shown in Figure 1. Historically, the mine was an open pit, although in recent years ore is sourced solely from underground operations. The processing plant features crushing and grinding, followed by carbon flotation and sulphide flotation. Carbon concentrate is a waste stream, and sulphide concentrate reports to pressure oxidation (autoclave) and CIL circuits for gold extraction. The final flowsheet is shown in Figure 2. Following commissioning in late 2008, the operation achieved commercial production on May 1st 2009. Gold recovery in flotation gradually increased to a 92-96% range at a throughput of ~3500-4000 tonnes per day. In late 2014, the operation commissioned a plant expansion to ~5000 tonnes per day. Following a commissioning period, the operation stabilised with recoveries in a 90-94% range, which over any given period was determined to be ~2% lower with statistical significance. The trends from start-up of gold recovery in flotation and throughput are shown as follows in Figure 3. In early 2016, Agnico Eagle Kittilä mine, along with Agnico Eagle Technical Services (AETS) partnered with Metrix Plant Technologies and TESCAN, to perform a Performance Assessment Campaign (PAC) at Kittilä, involving automated mineralogy on five key streams at Kittilä on 40 days selected from a 50 day period between February 15th and April 4th 2016, when plant operations were stable. In addition to the mineralogical data, metallurgical and operational data were pooled into a single, powerful database to explore opportunities for the operation to improve recovery in a sustained manner, ideally to the levels pre-expansion."

Jan 1, 2017

By R. J. McLaughlin

Acid mine drainage (AMD) can occur as a natural phenomenon through oxidation of sulfide minerals. Oxidation by air and water can be exacerbated by mining. Because AMD can exhibit low pH, it is capable of extracting heavy metals from mineral deposits. The result is highly acidic drainage with elevated heavy metal concentrations -the combination of which can cause extensive environmental damage. Because of the importance of these factors, this paper is focused on sulfate based AMD. Due to widespread mining, the occurrence of AMD is ubiquitous. As a result, several approaches to treatment have been developed. Chemical treatment using alkali is most commonly employed to treat AMD. There are alternative methods of treatment, as well as alternative ways of handling treatment sludges or concentrates. Dewatering of sludge or concentrates is beyond the scope of this paper.

Jan 1, 1996

By E. L. Piper

Natural graphite has been known for many centuries, having first been reported as a distinct mineral form by Gessner in 1565. At that time, graphite was used extensively as pencil "lead" because of the ease with which it marks paper. It is a black, unctuous material found as flakes, lumps, or needles in scattered locations throughout the world. The less crystalline, or "amorphous", natural graphites are thought to have been formed from coal under conditions of high temperature and pressure. The more crystalline varieties, such as those mined in Ceylon, probably were precipitated from molten solutions or were pyrolyzed from gaseous carbon compounds. Recognition of the good thermal and electrical conductivity of graphite, together with its highly refractory nature, led to an increasing number of appli¬cations for this material. Clay and pitch bonded natural graphite has been used in crucibles, refractories, foundry facings, and other high-temperature appli¬cations. These forms constitute the most important current uses for natural graphite in the United States. Other products containing natural graphite include batteries, lubricants, pencils, brake linings, etc.

Jan 1, 1973

By Georges Cote, Ehsan Alavi, Eren Kusdogan

The City of Toronto's Coxwell Bypass Tunnel is currently being constructed by North Tunnel Constructors (NTC) ULC, a joint venture of Jay Dee Canada, C&M McNally Tunnel Constructors and Michels Canada. This project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five 20 meter diameter storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. 120 m of Starter tunnel and 70 m of Tail tunnel were excavated with roadheaders to help with the launch of the TBM and as part of the contract base scope work. JayDee Canada in Collaboration with Everest Equipment Co. developed an innovative approach to design and build a stand-alone Ring Machine Erector nicknamed Enterprise to erect precast segmental lining in Starter and Tail tunnels in lieu of Cast-In- Place concrete. This paper describes the design and provides feedback on the innovative procedure used to install the rings.

Jun 23, 2024