Search Documents

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

A sociotechnical system (STS) creates a framework that allows an examination of how social and technical factors affect organizational outcomes within a specific environmental context. STS has been rigorously studied with a primary research focus addressing worker-technology interactions. Although these interactions are important, the social processes and interactions that occur whenever any technical or environmental change is introduced into the system have been undervalued. If social processes are better understood, mining organizations could efficiently prepare and stabilize for such changes. With this goal in mind, we sought to extend STS theory through applying principles of meta-design to analyze the results of two case study interventions. Specifically, we studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the Continuous Personal Dust Monitor) on factors within an STS including employees’ knowledge of, communication about, and use of technology to mitigate respirable dust sources. The results are presented in a way that first, addresses the overarching principles of meta-design STS including organizational participation, flexibility, and communication and second, examines how technology implementation processes differ when the organization is complying with a formal, higher-level requirement. Results show that a prominent focus on the social factors within an STS framework could help reduce unpredictability on the technical side and may improve communication within the system to help reduce adoption time, especially if and when accompanying a new, formal work process.

By Brian Khalighi, Massimo Franceschi, Giovanni Giacomin, Gianni Porta

Headrace Tunnels and parts of the Access Adit Tunnels of Kárahnjúkar Hydropower project, KAR-14, in Iceland will be excavated using three full-face Robbins Tunnel Boring Machines (TBM). TBM sizes range from 7.23 to 7.63 meters in diameter and the total headrace tunnel length is approximately 40 km. The crushed rock is transported on conveyor belts to disposal areas near each Adit. The estimated average excavation rate is approximately 25 meters per day per machine. Electricity will begin to flow in April 2007, and the project is scheduled for completion in 2009. This paper is divided into four sections. In the PROJECT OVERVIEW section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drives is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes in the TBM OPERATION section with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 2005

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology for supporting the Industry 4.0 has become the target of academic research in many sectors. This study reviewed the trends of open-source technology, its forms, and some industrial applications. As a case study using open-source hardware and software for the mining industry, this study proposed a low-cost environmental monitoring system for non-metallic underground mines to support mine safety and occupational health issues. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device. An open-source software, MIT App Inventor, was used for developing an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a non-metallic underground mining site to assess the performance of the system in both mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors still exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology for supporting the Industry 4.0 has become the target of academic research in many sectors. This study reviewed the trends of open-source technology, its forms, and some industrial applications. As a case study using open-source hardware and software for the mining industry, this study proposed a low-cost environmental monitoring system for non-metallic underground mines to support mine safety and occupational health issues. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device. An open-source software, MIT App Inventor, was used for developing an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a non-metallic underground mining site to assess the performance of the system in both mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors still exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors

By Barry Olson

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The company has since committed US$1.5 billion to construct the mine, mill and associated facilities. The first of two 50-kt/d (55,000-stpd) mill and flotation lines is currently being commissioned while engineering and construction continues on the second line. A high-pressure grinding roll (HPGR) will ultimately take total throughput to 130 kt/d (142,000 stpd). The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level and it is situated in a wide east-west valley. Except for one small outcrop (Peñasquito), the area is covered by up to 30 m (98 ft) of alluvium.

Jan 1, 2009

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By Albert Ruiz

South Coast Water District (District) operates the Beach Interceptor Sewer Tunnel (BIST) in South Laguna, Orange County, California between Mon-arch Beach and Aliso Beach (Figure 1). The 10,424-foot long BIST houses a 24-inch Techite gravity sewer pipeline critical to the District Sanitary Sewer Collection System that conveys 1 MGD of raw sewage to a wastewater treatment plant. The original tunnel was constructed in 1954 and the sewer line replaced in 1974. Periodic inspections by sewer pipeline maintenance crews have documented deterioration of specific intervals of the tunnel within the past few years (Sancon 2003). Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline. A 50-foot section of the tunnel was determined to be in need of immediate repairs, which were carried out from January to August in 2007. This section was enlarged to a horseshoe shape and lined with shotcrete. The pipe was encased in concrete in the invert of the new enlarged cross section. Hatch Mott Mac-Donald (HMM) designed the emergency repairs, carried out an assessment of the rest of the tunnel alignment, and is currently developing a work plan for rehabilitating the entire tunnel.

Jan 1, 2008

By David Crouthamel, Raymond Henn

"The need to fill the void space or annulus created between an excavated tunnel or shaft and the final lining system has long been a requirement in underground construction. Most of those types of voids are created as a result of employing the two pass tunneling lining method. Filling of this void is called backfilling. For many years the materials used as backfill were primarily reinforced and non-reinforced concrete, sanded grout, neat cement grout, or blown-in sand/pea gravel. However, in the past 20 years the use of cellular grouts/cellular concrete as the backfill material has greatly increased. Most cellular grout is made of a mixture of water, Portland cement (with or without the addition of fly ash), a foaming agent and admixtures such as a water-reducer or superplasticizer.It is the authors’ preference to use the term cellular grout as opposed to cellular concrete since by ACI Concrete Terminology an ACI Standard (ACI CT 13), concrete contains aggregates. Normally cellular grout does not contain sand (finite aggregate), but almost never contain course aggregates.The authors believe there are several reasons for this increased use of cellular grout as backfill, such as:• The increase utilization of the various trenchless tunneling methods. Tunnels constructed using trenchless method tend to be smaller in size, excavated diameter or cross sectional area. Making man-entry for placing backfill from inside the secondary liner, utilizing pre-installed grout posts, more difficult if not impossible. It is these workspace restrictions that are the drivers as to when to utilize grout ports installed during the pipe/liner fabrication versus grout delivery pipes installed within the void/annulus space.• The ability of cellular backfills to be pumped and flow longer distances.• The unit weight of cellular grouts can be controlled by mix design and generally can range from 560 Kg/m3 (35 lbs/CF) to 1040 Kg/m3 (65 lbs/CF)."

Jan 12, 2017

By F. L. Pirkle

A heavy-mineral deposit about 1.6 kilometers (I mile) in length and averaging about three meters (10 feet) in thickness is exposed approximately130 kilometers (80 miles) east of Denver, along Interstate 70, in Elbert County, Colorado near the town of Limon. The deposit is exposed in a geomorphic feature known locally as Titanium Ridge. The dominant heavy minerals, accounting for about 70% of the total heavy mineral suite by weight, are ilmenite, garnet, and zircon. The mineralized zone appears in a series of visually interpretable facies that are stacked vertically and represent subtidal, forebeach, backbeach, washover fan, and aeolian depositional environments. These paleoenvironments are analogous to depositional environments represented by a modern heavy-mineral bearing facies tract on St. Catherines Island, Georgia. Thus, Titanium Ridge provides evidence that heavy-mineral accumulation models for late Cenozoic deposits in the Georgia and Florida coastal plains are applicable to heavy-mineral deposits of the Western Interior subsurface and, by implication, the Western Interior Seaway, extending from Mexico to the Canadian Arctic.

Jan 1, 2011

By Yves St-Amour, Vince Luongo

This paper will discuss one of the largest construction projects the City of Portland has undertaken. This phase of the Willamette River Combined Sewer Overflow (CSO)project consists of approximately 18,500 ft of tunnel in soft ground, requiring the construction of six deep shafts and jet grout ground improvement. The purpose of the project is to reduce volume of combined sewerage overflows from the drainage areas on the west side of the Willamette River. Bencor-Petrifond-Pacchiosi Joint Venture was awarded a contract to design and construct six deep circular shafts, jet grout ground improvement for three bridges and jet grout ground improvement break-in/outs for some shafts. Of the six shafts the Pumping Station Shaft was the deepest and largest, requiring a permanent ground support system with a deep jet grout ground water cut-off to 335-ft deep. The joint venture used state of the art methods and equipment to achieve its objectives and build the structures through some very difficult alluvial soils to great depths next to the Willamette River. The paper will provide a general discussion of the shaft construction and jet grout ground improvement installed for this phase of the project. It will also discuss some of the technical challenges encountered while effectively managing risk and costs, resulting in a successful project completed in a timely manner.

Jan 1, 2005

By N. L. Hayward, V. H. Ness

In the past decade Australia has seen the development, construction and commissioning of three complex processing plants for the treatment of lateritic nickel ores. These have all been based on high pressure acid leaching (HPAL) for extraction of nickel and cobalt into solution, followed by solid liquid separation in a CCD circuit. However, flowsheets for separation and purification of the nickel and cobalt diverge markedly. The existing plants have been commissioned with varying degrees of success, with a variety of problems ranging from materials of construction to inadequate design. While the process problems are not insurmountable, there is much room for improvement. Currently there are several new HPAL plants at the feasibility or financing stage. All of these have adopted one of the existing flowsheets. Most of the enhancements have focused on increasing autoclave size. It is now time to assess the success and failures of the three existing plants and incorporate this experience in a design for productivity, efficiency and reliability. Towards this end, this paper discusses aspects of flowsheet optimization, materials of construction and engineering design.

Jan 1, 2001

By Kasimcan Koruk, Julian M. Ortiz

A geological model accounting for uncertainties possesses important advantages for resource estimation. Machine learning algorithms (MLAs) employed on multivariate geochemical datasets open up ways to new methodologies for such geological models with ease in comparison to traditional geostatistical methods. This article proposes a two-step MLA with an ensemble implementation to define geological domains and their uncertainties based on geochemical data. The proposed workflow is applied hierarchically on a dataset from a porphyry copper deposit to perform binary classification that can be attributed to alteration domains.

Mar 1, 2024

The following is a summary of some of the companies that were exhibiting their products and services at MINExpo INTERNATIONAL 2000. Atlas Copco develops, manufactures and markets rock drilling tools, tunneling and mining equipment, and surface and geotechnical drilling equipment. The company provides a line of drilling products, including production drilling rigs, rock reinforcement bolts and rock drills. Atlas Copco’s Boomer is a series of high-capacity drill rigs that provides economy, production capacity and reliability

Jan 1, 2000

Scattered north and south along a 161-km (100-mile) stretch of Interstate 80, Newmont Min¬ing Corp. owns four active mining properties in Nevada?s northern high desert ? Carlin Trend Operations, Midas, Twin Creeks and Phoenix. Among the four, there are nine openpits, five underground mines and 14 processing facilities. While gold is the predominant ore, silver and copper are also produced. And in a move to hold down energy costs, Newmont built and owns the 200-MW (net), coal-fired TS power plant. This plant provides about 65 percent of the power used for Newmont?s own operations, while the rest is sold to NV Energy, which services Nevada and northeastern California. Bringing the Phoenix Mine ? Newmont?s newest in Nevada ? on-line presented many developmental and operational challenges. Located about 19 km (12 miles) southwest of the town of Battle Mountain, the general area had been home to prospectors and other mining companies since the 1860s. But any profitability in developing the lower grade gold, copper and silver deposit at Phoenix proved elusive, with Battle Mountain Gold being the last company to make an attempt. When Newmont acquired Battle Mountain Gold and its Phoenix reserves in 2001, the lower grade of ore was not a deterrent. Newmont found Nevada-wide cost savings synergies for maximizing profit during the depressed gold market of the late 1990s. The new property was aptly renamed the Phoenix Mine, a nod to its rising from the ashes of the dreams and efforts of previous mine owners.

Jan 2, 2010

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic meters per hour) for dozers operating in hard-rock bulk push applications. The particle size distribution of the material employed in the test rig was modeled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard-rock dozer push operations. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 to 40 m.

By VIVEK KASHYAP, PATRICK TAYLOR

Zinc ferrite is the major phase component present in zinc refinery residue (ZRR) and electric arc furnace dust (EAFD). Up to 71 percent zinc ferrite has been reported to be present in ZRR, and in most studies zinc ferrite has been deemed the major phase in EAFD. In 2010, the global annual production of EAFD was 3.7 Mt, with 15.20 kg of EAFD generated per ton of recycled steel [1]. The generations of ZRR and EAFD have been growing over time, requiring a greener approach for the reutilization and extraction of valuable elements. ZRR can be a potential source of zinc, as its zinc content is as high as 30 percent [2,3]. The presence of zinc ferrite makes the extraction of zinc difficult because zinc ferrite is refractory to leaching, and direct leaching is inefficient. The Waelz process is currently employed to extract zinc from EAFD and other metallurgical wastes. The Waelz process operates in the temperature range of 1,100 to 1,500 °C and uses coke as reductant. This study explores a carbon-free and relatively low-temperature process for the selective extraction of zinc from pure zinc ferrite.

By N. T. Lowe

The National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory (SRL), investigated a means to evaluate the potential impact of surface conditions above underground mines on emergency response activities. Recent events have highlighted the need to conduct critical emergency operations on the surface above underground work areas. Accessibility and usability of the surface, such as the ability to drill holes or deploy seismic monitoring or through the earth communications systems, are an important consideration for emergency response planning. This paper identifies critical surface conditions such as: surface waters, valley fill, highways, railroads and significant structures that must be considered in emergency response planning and in the conduct of emergency operations as they relate specifically to the seismic detection of trapped underground miners. Results of case studies indicate a need to consider the impact surface conditions may have on emergency response capabilities.

Jan 1, 2009

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By John Reilly

Costs of complex/underground projects have been consistently underestimated and delivery on time and on budget has been problematic. This has been attributed, to inadequate cost estimates and unidentified and/or insufficiently managed risk. Use of probabilistic cost estimates like the Washington State Department of Transportation?s CEVP® process (developed by the author and others) has produced more realistic cost estimates, explicitly identified and quantified risk (as input to risk management plans) and early awareness of key project issues. This paper updates previous work (NAT 2004), adds implementation detail for probalistic cost estimating as used by WSDOT, FHWA and other agencies and will address key issues in risk management, as related to probalistic cost estimates.

Jan 1, 2008

By Will Jansen

When Enron rocked the United States with its Titanic-sized financial accounting scandal, miners and metallurgists were probably too busy on the mine sites in remote locations to wonder about its ripple effect. But then Enron sank, Arthur Andersen tanked and the list of scandals, costing billions of dollars, continued to ripple. Followed by the Public Company Accounting Reform and Investor Protection Act of 2002 (Sarbanes-Oxley), the recent credit crunch and weak economy, the currents from Enron?s collapse eventually washed right into the mine and the mill. These events placed intense scrutiny on metals production accounting processes as traditional semi-qualitative metal accounting practices provided insufficient credibility and transparency. ?There is growing intolerance of organizations that are unsure about the location of thousands of tonnes of ore, which will typically lose 10 to 15% of their notional value on the way to the concentrator,? Rob Morrison wrote in the opening chapter to An Introduction to Metal Accounting and Balancing. ?If the measurement and forecasts also contain qualitative (fudge) factors, a very real suspicion might emerge about just how much metal might disappear (by theft or misplacement) before detection becomes likely.? Metallurgical accounting, put simply, is the tracking and reporting of the quantity and quality (tonnage and grade, usually) of materials entering or leaving each stage from source to product for a specified accounting period. Lacking an accounting standard, metals accounting in precious metal operations has been performed in an ad-hoc, informal manner, leading to numerous errors and unidentified potentially significant inefficiencies and financial losses. As a result, mining companies are beginning to examine the quality of their metals accounting systems since they form the basis of mining company?s financial accounts and reports. As part of an effort to create that accounting standard in the mineral industry, University of Queensland?s Julius Kruttschnitt Mineral Research Centre published the textbook An Introduction to Metal Accounting and Balancing in 2009. While development of a textbook and standard are significant steps forward, the challenge in the precious metals industry is in the application of some of these suggested practices. Though improving process transparency and precious metals accounting reporting accuracy is a key driver for change from the financial side, perhaps even more important is the potential benefit to operational performance that comes with better measurement, accounting and reconciliation systems. Loss of precious metals, processing of waste and inefficient mining and processing systems are all problems that are faced in an operation on a daily basis that can help be resolved through improvements in metal accounting and reconciliation. The financial consequences of such operational inefficiencies and bad decisions based on poor information are arguably greater than consequences of fraudulent accounting. Large discrepancies between mine and mill measurement systems that measure the quantity and quality of valuable material currently exist. Some of these are expected because of statistical variation, but inherent random measurement variation is sometimes an insufficient explanation. Though the mill can usually make much better production estimates through their measurement systems (that is, less variation), this knowledge rarely benefits the mine. 3 Moreover, even if the mine does a reasonably good job of estimating expected production at the grade control level (in situ), issues such as blast movement, poor mining practice and inefficient ore/waste classification make for a disconnect between the in situ estimates of the mine and the estimates from the concentrator. This inhibits effective evaluation of the reserve and grade control models using concentrator estimates. Linking the two ends, mining and concentration, is a neglected area sorely in need of an overhaul. Hence the need for improved mine to mill reconciliation ? the area of comparing, balancing and adjusting production estimates between mine and mill for consistency in reporting.

Jan 1, 2009