Search Documents

By J. W. MacDonald

PROPERTY AND PRODUCTION: Around 100 Million Tons of Recoverable Coal are available from the approximate 10,000 acres allocated to the mine. Over 1300 acres of surface land holdings extend well beyond the limits required for plant site, storage tracks, water supply reservoir, settling ponds and waste disposal. COAL: Extensive core drilled testing confirmed the early indicated high quality of the #6 Seam Washability data show less than four percent of the' coal seam required removal to provide a superior product for the available market. PREPARATION PANT DESIGN: The limited needs enabled Preparation Plant Design to meet the requirements without inclusion of novel equipment. The simplified needs afforded ample opportunity for considering increased automation where advantage or economy was antioipated. Plant design included protection of opportunity for pre-drying in advance of air cleaning the fine coal and accommodations for addition of Dense Media separating equipment in event warranted or required by future market changes. Protection is also afforded for addition of Raw Coal Storage accommodations in event warranted. Figure I shows the Preparation Plant Flow Sheet.

Jan 1, 1961

By H. Askari-Nasab, B. Osei, K. Awuah-Offei

The U.S. coal mining industry consumes approximately 142 billion kWh/a of energy. The U.S. Department of Energy estimates that the industry’s annual energy consumption could be reduced by 49%. This constitutes nearly $3.7 billion of potential savings on coal production costs at 5.3¢/kWh of energy. Additionally, with climate change regulation on the horizon, any benefits from energy savings in the near future are compounded by associated reductions in CO2 emissions. Research indicates that operating conditions significantly affect energy efficiency. Modeling and simulation have been shown to be a cheap and reliable means of evaluating the effects of process interactions and operating conditions. The goal of this work was to apply stochastic process simulation to model the energy efficiency of a typical truck-and-shovel mining system and use the model to evaluate production strategies to improve energy efficiency. The research team conducted energy audits of truck-and-shovel overburden removal and used the results to develop regression models describing truck and shovel fuel consumption. The team then built a stochastic simulation model of the truck-and-shovel overburden removal operation and used it to assess a variety of improvement measures by simulation experimentation. Valid fuel consumption models for shovel loading and truck haulage have been formulated, based on the energy audit results. Valid stochastic process models of truck-and-shovel operations have been formulated to study energy efficiency. The following strategies, in decreasing order of impact, provide the most energy savings for truck-and-shovel overburden removal at the mine: (1) shorten haul roads, (2) increase shovel capacity and (3) increase shovel utilization through optimal truck matching. Additional data will be required to adequately describe operator effects on energy efficiency.

Jan 1, 2011

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By Charles Kocsis, Pedro Nascimento, W. Patrick Arnott, Samuel J. Taylor

Respirable crystalline silica (RCS) is an inhalation health hazard for mining and industrial work environments and must be monitored. We provide theoretical analysis of real-time measurements for determining RCS mass concentration without the use of filters by using photoacoustic spectroscopy. The suspended dust in the mine air can be continuously sampled by the photoacoustic instrument. A tunable quantum cascade laser is the light source, allowing for determination of interferences such as kaolinite, coal dust, and water vapor. The most useful spectral region is found to be between 11 and 13 μm. Absorption by water vapor, and, to a lesser extent, carbon dioxide, in this spectral region has gaps that allow for quantification of the aforementioned dust species as well as a convenient check on the calibration of the instrument. This work brings photoacoustic measurement of aerosol to the mid infrared range where spectrally dependent light absorption can be used to quantify dust composition and mass concentration.

Jul 31, 2022

By D. N. Madge

A survey is given of production scheduling systems currently in use or contemplated for future use in Cominco operations. Emphasis in this presentation is made on the chain of decisions that are made with the help of mathematical programming models. Some attention is devoted to the structural properties of the models.

Jan 1, 1966

By L. S. Gertsch, M. Z. Abu Bakar

Linear cutting tests of a porous sandstone with a radial drag pick show that saturation of rock with water can increase the specific energy of fragmentation. This appears to be due, in this case, to a saturation-induced increase in the forces acting on the cutting tool without a concomitant increase of the fragmented volume. The mechanisms of this reaction are explored by examining various responses of the parameters controlled and induced during the linear cutting tests, such as cut spacing, cutter penetration, three-dimensional forces and muck production. A program of load-indentation testing is underway to evaluate the permeability threshold of this behavior. These findings are opposite from those made when the same rock is cut with a constant cross-section disc cutter reported elsewhere (Abu Bakar and Gertsch, 2011). Such results highlight the effects of different cutting tool designs, and indicate the need for a well-coordinated program of research to support effective excavator design and selection.

Jan 1, 2012

By James L. Hendrix

This paper is intended to give the reader an update on the work being done at the Mackay School of Mines about the fate of cyanide on precious metals mill tailings waste. During the last two years several tailings impoundments have been sampled and analyzed for total and free cyanides. From our sampling program we are beginning to learn valuable information concerning the fate of cyanides in precious metals mill wastes. Included in this paper is a detailed description of our sampling and analytical techniques. Also, some of the data obtained from five sites are given.

Jan 1, 1986

By J. Mark Richardson

The use of an integrated software package to simulate and optimize the performance of mineral processing circuits is illustrated by three examples. Each represents application of the software and associated techniques to optimization of an existing plant. In the first example, a South-western U. S. copper company employs the method to simulate and improve performance in crushing, screening and SAG milling. A second copper producer evaluates equipment changes and flowsheet alternatives in a closed-circuit ball mill-cyclone operation. A Southeastern U. S. aluminum refinery optimizes performance of a dry milling and classification circuit for production of carbon particles used in anode casting. Graphical and tabular data describe the circuits simulated and the results achieved in each example.

Jan 1, 1990

By John L. Shafer

A process for the conversion of stibnite (Sb2Sj) concentrates, crude antimony oxide, or metal to a pure cubic antimonous oxide (senarmontite) has been developed on a laboratory scale. The conversion of stibnite to senarmontite has been piloted. The high purity of the final product is the result of forming antimony trichloride as a low temperature distillable intermediate. To obtain the antimony trichloride the stibnite, or crude oxide is slurried in molten antimony trichloride and reacted with gaseous hydrogen chloride. Antimony metal is oxidized to the trichloride with chlorine. The hydrogen sulfide produced from the hydro- chlorination of stibnite can be upgraded to a strength of 95% or greater for further treatment. The crude antimony trichloride is separated from the gangue by a preliminary evaporation and then is fractionally distilled and the trichloride distillate has less than 50ppm of arsenic and lead combined (the most troublesome impurities in antimony processing). The purified antimony trichloride is then hydrolyzed with sodium or ammonium hydroxide to produce the cubic form of antimonous oxide (senarmontite) to the exclusion of the rhombic form (valentinite) which is photosensitive. The advantage of this process is the ability to treat a wide range of antimony ores, concentrates, and metal to yield a high purity oxide in a controllable range of particle sizes.

Jan 1, 1975

By Jiawang Hao, Qinglong Zhang, Liang Han, Chuhan Wang, Shenfang Chen, Lan Qiao

The surface collapse and surrounding rock failure caused by goaf instability are the mining disasters that cannot be ignored. It is of great value to evaluate the stability of goaf accurately and treat it economically for the mine safety and the maintenance of ecological environment. However, in previous studies based on numerical simulation methods, the spatial complexity and the irregularity of actual goaf were not considered. Therefore, based on the internal space data of goaf obtained by high-precision laser detector, the goaf stability was comprehensively analyzed through Plaxis software and two-stage fuzzy judgment theory in this study. To effectively improve the goaf stability, the optimal backfill parameters for the goaf treatment were obtained by a series of mechanical tests. The research results provide some good references for the stability evaluation and the treatment of underground goaf.

Sep 26, 2023

By J. Espí

The mineral price assigned in mining project design is critical to determining the economic feasibility of a project. Nevertheless, although it is not difficult to find literature about market metal prices, it is much more complicated to achieve a specific methodology for calculating the value or which justifications are appropriate to include. This study presents an analysis of various methods for selecting metal prices and investigates the mechanisms and motives underlying price selections. The results describe various attitudes adopted by the designers of mining investment projects, and how the price can be determined not just by means of forecasting but also by consideration of other relevant parameters.

Aug 1, 2013

By G. Bylapudi, A. Spearing, J. Weber, K. Mondal

U.S. National Institute for Occupational Safety and Health (NIOSH) reports state that about 100 million rock anchors are installed annually in U.S. coal mines (Tadolini et al., 2006), and rock-related safety remains an issue. The majority of these coal mines have conditions that make corrosion probable in the longer term. Despite this, very little research has been performed to analyze corrosion and its effects on rock anchors in coal mines. To further evaluate the effects of corrosive conditions in coal mines on rock anchors, three different experiments were conducted during an initial Illinois Clean Coal Institute (ICCI)-funded project from 2008-2009. The results of these experiments were further studied, with additional tests, in the extended ICCI-funded project during 2011-2012. The experiments were destructive testing, electrochemical testing (potentiodynamic polarization tests) and open circuit potential (OCP) testing, conducted in order to study corrosion in environments similar to those found in Illinois coal mines with a focus on major rock anchor types typically installed underground. Destructive test results showed highest reduction in peak strength at higher pH and temperature. From the destructive test results, epoxy-coated and galvanized anchors were observed to be better when compared to uncoated. Electrochemical testing was performed to find the corrosion potential and corrosion rates of ASTM A615 steel grades 40, 60 and 75 in four different solutions of varying sulfur content at ambient temperature. The effect of temperature and pH levels on corrosion potential and corrosion rates of steel grades were also evaluated with additional electrochemical testing, where an increase in temperature with all other constant conditions caused a significant increase in the corrosion penetration rate. OCP data indicated higher corrosion potential values (-mV) for rock anchors in wet areas, when compared to those from the dry areas. OCP test results of the rock anchors from the laboratory corrosion chambers were similar to those measured in the sampled coal mines.

Jan 1, 2013

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Significant strides have been made in optimizing the design of filtration and pressurization systems used on the enclosed cabs of mobile mining equipment to reduce respirable dust and provide the best air quality to the equipment operators. Considering all of the advances made in this area, one aspect that still needed to be evaluated was a comparison of the efficiencies of the different filters used in these systems. As high-efficiency particulate arrestance (HEPA) filters provide the highest filtering efficiency, the general assumption would be that they would also provide the greatest level of protection to workers. Researchers for the U.S. National Institute for Occupational Safety and Health (NIOSH) speculated, based upon a previous laboratory study, that filters with minimum efficiency reporting value, or MERV rating, of 16 may be a more appropriate choice than HEPA filters in most cases for the mining industry. A study was therefore performed comparing HEPA and MERV 16 filters on two kinds of underground limestone mining equipment, a roof bolter and a face drill, to evaluate this theory. Testing showed that, at the 95-percent confidence level, there was no statistical difference between the efficiencies of the two types of filters on the two kinds of mining equipment. As the MERV 16 filters were less restrictive, provided greater airflow and cab pressurization, cost less and required less-frequent replacement than the HEPA filters, the MERV 16 filters were concluded to be the optimal choice for both the roof bolter and the face drill in this comparative analysis case study. Another key finding of this study is the substantial improvement in the effectiveness of filtration and pressurization systems when using a final filter design.

Aug 1, 2016

By Jim Britton

Sustained elevated metal and coal prices in 2011 continued to drive mining projects across British Columbia. The province is the top producer of copper, exporter of coal and the only producer of molybdenum in Canada. The province also produces significant amounts of gold, silver, lead and zinc and more than 30 industrial minerals. The total 2011 value of solid metal production is an estimated $8.6 billion and the outlook for 2012 is positive. British Columbia is poised to bring several new mines onstream in the next few years. Construction continues at the New Afton and Mt Milligan copper-gold projects that are anticipated to be open in 2012 and 2013, respectively. The provincial Environmental Assessment Office indicates there are 26 mine proposals in process with three currently under review and 23 in the preapplication stage. The following text briefly describes 2011 metal and coal mining activities in the five regions reported on by the provinces? regional geologists (Fig. 1).

Jan 1, 2012

By Richard L. Gordon

At almost no time since the end of World War I has the coal industry been free from serious threats to its competitive position. At present, the critical question is whether the industry can maintain its position in the electric power market and this paper reviews the prospects in this area. Our report is part of a study, supported by Resources for the Future Inc., dealing with coal demand in general. Like most elements of coal economics, it has received much less analysis than problems in other energy sectors--a defect we felt worth correcting. We have concentrated on electric power elements of the market. The nature of the coal market makes this the natural choice. Three markets absorb over 80 per cent of coal production and are considered in our overall work. The completely excluded sectors are largely catchall categories in which coal use is declining anyway. Comparing the three markets included in the overall study, we see: modest growth is the most optimistic forecast for metallurgical coke; export growth depends to a large extent on policies of foreign governments. Electric power use, however, has rapidly grown to absorb over half of coal output and coal's prospects depend almost entirely on continued expansion of this market. Throughout the 1960's the demand for coal used to generate electrical power in the United States grew at an average rate of 6.5 per cent annually. This growth rate will be sustained until at least 1976.

Jan 1, 1971

By John S. Owens

The National Steel Pellet Project and the Butler Taconite Project are operated by The Hanna Mining Company in the vicinity of the towns of Keewatin and Nashwauk, on the western Mesabi Range. Production began in 1967, after seven years of exploratory and development diamond drilling and reconnaissance magnetic surveys, Previously, direct shipping hematitegoethite ores and gravity concentrates had been produced in the area from numerous open pits and several underground mines since the start of the century. Total shipments of these oxidized ores amounted to more than 200 million tons, but at the present time such reserves are nearly exhausted, and there are no mining operations in the Keewatin-Nashwauk area except at the two taconite projects. The locations of all of the present taconite operations on the Mesabi Range are shown in Figure 1, extending for a distance of about seventy miles from the Butler plant to the Dunka River area. The Butler and National plants have a combined rated capacity of 4.4 million tons of pellets. Their reserves cover a combined strike length of about eight miles on the Biwabik iron formation. All of the intervals between present taconite operations on the Mesabi are potential sources of additional magnetic taconite; in particular, exploration and economic studies have been carried out by Jones and Laughlin Steel Corporation in the Biwabik area between Aurora and Virginia, and by Pickands Mather and Company in the Hibbing area. However, west of the Henna and Butler holdings, it appears unlikely that magnetic taconite exists in commerical quantities at economic depths due to extensive oxidation of magnetite to hematite.

Jan 1, 1968

By Zachary E. Wedding, Zach Agioutantis

Excavation of underground openings results in the redistribution of the in situ stress into the rock adjacent to the opening. Stress redistribution depends on opening geometry, pillar geometry, material properties, possible confinement, and constitutive models describing the behavior of adjacent rock. This paper presents typical pillar stress distributions for elastic and yielding pillars as a function of opening geometry, material properties, and material constitutive models and highlights the differences between them. Stress distributions are compared with empirical strength profiles that have been developed for coal pillars as well as actual pillar geometries documented for stone pillars.

Jul 1, 2023

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production; however, the thermal state of pellets in drying section is still unclear. In this study, the temperature distribution of drying section was investigated using computational fluid dynamics (CFD). Based on the calculated results of airflow velocity, space temperature distribution, and the temperature change of pellets, it concluded that there is a coupling effect in drying section in traveling grate. The gas with higher temperature in DDD transfers heat to UDD through the gap of the insulation board, and the temperature gradient of the pellet bed changed before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD was displayed in UDD in advance. Moreover, a contrast experiment was conducted to verify the model.

Feb 1, 2021

By Michael L. Clar

Reclamation of surface mined lands has two basic objectives: (1) the elimination or abatement of undesirable environmental conditions, and (2) the restoration of mined land to its former or more productive uses. This paper addresses some of the planning concepts and site factors that influence the selection of suitable land uses for surface mined lands. Three planning concepts included in the discussion are: (1) mine land planning, (2) comprehensive land use planning, and (3) environmental site planning. The site factors that will influence the selection of an appropriate land use have been grouped into three categories: (1) legal, (2) geographic, and (3) natural. The natural factors are further subdivided into three groupings: geomorphology, soils, and climate.

Jan 1, 1981