Search Documents

By D. M. Carris

Since the Buffalo Creek incident in February, 1972, Federal and state environmental agencies have had the pressure on the coal industry in the Appalachian area to close the coal processing plant water circuits. In an attempt to comply with this requirement, Eastern .Associated Coal Corp. decided to install a vacuum disc filter system at its Kopperston plant to eliminate the tailings pond and reduce the amount of plant make-up water. It was recognized at the time that the plant static thickener tailings would be a very difficult slurry to dewater because of its unusually high clay content. The following is a case history of the Kopperston installation and the refinements Eastern has made in its vacuum disc filter operation to increase efficiency.

Jan 1, 1979

By Snehamoy Chatterjee, Sanjay Kumar Palei, Smarak Das

Machine manufacturers’ recommendations on maintenance strategies of capital-intensive draglines are not always based on real data and therefore lead to losses from downtime. This paper proposes a preventive maintenance strategy for a dragline deployed in an opencast coal mine based on reliability-centered maintenance and failure-mode-effects analysis using real operational data. Reliability-centered maintenance replaced a cluster of critical failure components of the dragline while satisfying two specific conditions: (i) the components should be replaced at the earliest mean time to failure (MTTF) within the group and (ii) the time taken to replace all the parts should be equivalent to the maximum downtime within the group. Estimated threshold weightage factor identified twenty-six critical failure components for the preventive maintenance strategy, and clustering of components divided them into nine groups. In a group, the loss that is expected to occur by replacing some of the components before their failure, and the gain by reducing the overall maintenance downtime, has been explained through a cost-benefit analysis. The total net profit generated is calculated as US$200,178. This clustering activity also led to a reduction of annual downtime by 231 h, whose approximate market price as equivalent coal production costs $295,365.

May 28, 2020

By Weiran Zuo, Jinsheng Guo, Chun Yu, Jinyu Zhan, Bao Guo

High-precision prediction of the target minerals’ content in the feed and concentrate products is vitally important for the efficient beneficiation of mineral resources. Visible and near-infrared (NIR) spectroscopy provides a cost-effective way for online measurement of the mineral content in an industrial process. In this investigation, simulated specimens consisting of five different types of minerals that are present in the copper oxide ore, malachite, quartz, calcite, hematite, and chlorite were prepared with a variety of malachite contents, and the mixed specimens were analyzed by a visible-NIR spectrometer in an integral sphere mode. The reflectance spectrum is used as input and the malachite content as output to build the prediction model. The obtained data was modeled by support vector machines (SVM), and a Grey Wolf Optimization (GWO) is proposed with the goal of improving the prediction accuracy. The GWO algorithm has been applied to adaptively search for the best combination of featured values. After cyclic comparison, the optimal penalty factors c and g can be quickly and accurately selected. The experimental results show that the SVM model established by the GWO algorithm has a better fitting effect and smaller prediction error, compared with other models.

Aug 3, 2023

By Zhiyuan Ma, ZUI WANG, Xincheng Hu, Jianwei Cheng, Junhong Si, Yi Qin, Gao Ke

The harmfulness and destructiveness of mine gas explosion is quite serious, which is the first of all kinds of coal mine disasters. Once the gas explosion occurs, it could instantly generate explosion shock waves, high temperature airflows, and disaster gases, which cause the destruction of underground ventilation structures, disruption of airflow direction in a mine ventilation network, and miners’ deaths by asphyxiation. As an important barrier to prevent the spread of accidents caused by the gas explosion, the safety and reliability of the mine seal affects the mine’s production and the health of workers. Due to the demands of coal mine production and transportation, a large number of longitudinal and horizontal roadway networks have been developed underground. There are not only many flat and straight roadways in the complex roadway network structure, but also a large number of different types of bifurcations and bends. Once a gas explosion occurs, the impact of the blast waves on the mine seal after passing through the complex path is difficult to determine. Therefore, this paper establishes a numerical model of bifurcated and cornered roadways and studies how the impact of gas explosion shock waves on the structure of sandwich mine seal after passing through different types of bifurcated and cornered roadways. The damage state of sandwich mine seal is analyzed. The researching finding could prevent and manage the spread of gas explosion disaster, and improve the disaster mitigation of mine explosion accident.

Jul 11, 2023

By M. Hepokoski, M. Klein

"Mine refuge shelters are designed to protect mine workers from hazardous environmental conditions after a mine disaster, but high temperature and humidity levels inside these shelters may pose a significant safety risk. Due to the safety risks associated with human testing, detailed thermal models of shelters and human occupants have been developed using TAITherm simulation software. These models are used to predict the temperature and humidity within the shelter resulting from metabolic heating, evaporation due to sweat and respiration, moisture and heat from the shelter’s carbon dioxide scrubbing system, and heat transfer within the shelter. A detailed human thermoregulation model simulates the sensible and latent heat generated by the shelter occupants, and predicts the occupant’s body core temperature and moisture lost due to sweating and respiration. This information is used to assess the safety of the shelter. This paper presents the technical details of the human thermal model, validation comparing the human model to human subject test data, and results of a mine shelter analysis. IntroductionPortable mine refuge chambers are used in U.S. coal mines to provide protection to mine workers from hazardous conditions following a traumatic event. Although these shelters are designed to supply clean air and sustenance for up to 96 hours, prolonged exposure to the mine shelter environment itself can pose a substantial risk to human safety. Heat generated by the shelter occupants combined with heat from the carbon dioxide (CO2) scrubbing system can raise the shelter interior temperatures and relative humidity to dangerous levels that can lead to heat stress in humans. Unfortunately, the thermal burden associated with mine shelter exposure is not well characterized due to potential hazards associated with underground human subject testing. In order to assess the thermal burden on people within a mine shelter environment, a detailed thermal model was created to accurately predict the temperatures and humidity levels within the shelter, and the impact of these environmental conditions on human occupants. The model consists of a mobile inflatable tent-type mine shelter with 23 humans, and includes the surrounding mine environment. The thermal simulations were performed using a validated commercial heat transfer prediction computer software. Additionally, a module of the software provided the capability to simultaneously model the thermophysiology of 23 unique humans contained within the mine shelter. The human thermal models accounted for the thermal interaction with the environment and provided a core temperature response prediction that can be used to evaluate survivability in heat stress situations (U.S. Army, 2003). The models can also be used to determine maximum occupancy in order to maintain safe temperature and humidity levels inside the shelter in specific mine environments, to optimize shelter size for maximum heat dissipation, or to simulate active cooling systems."

Jan 5, 2017

By M. C. Fuerstenau

A number of interesting and. important phenomena were revealed during a study of the response of beryl to sulfonate flotation (1). Perhaps the most important observation is the effect of various cations on flotation response. Experiments showed that in the vicinity of pH = 3. 0, about three ppm Fe.+++ increased recovery of leached beryl from about 60 to 100 per cent, whereas about four ppm Ca++ reduced the recovery from 60 to 2 per cent. With the exception of ferric iron, all of the other cations investigated reduced flotation recoveries drastically at this pH. As postulated in the paper "Sulfonate Flotation of Beryl", (1) even with low concentrations of polyvalent cations and sulfonate (on the order of one ppm), cation¬ sulfonates are precipitated immediately in solution. That is, blueish-white clouds .were noted to form after given additions of salts to. known solutions of sulfonate. Furthermore, it was also shown that one-hundred-fold more ferric iron than necessary to form the precipitated cloud had to be added to effect complete flotation. In other words, some form of solid ferric sulfonate was found to function as the collector in these systems. The form of the compound was suggested to be Fe (RSC3)2OH and that bonding to the surface occurs through the hydrogen of the hydroxyl. As the form of this compound was shown to be dependent on the extent of hydrolysis of ferric iron, it is to be expected that ferric iron will be unique in some pH region. Further, if the presence of hydroxyl in the neutral precipitated compound is of primary importance, then other cations should function similarly but at different values of pH, since they will hydrolyze at different concentrations of hydroxyl ion. To determine whether the premise of hydrolysis is correct, the study was extended to quartz systems lit the presence of various cations at various values of pH.

Jan 1, 1964

By Oluwafemi Salami

Conducting full-scale fire experiments in underground mines is difficult and expensive. Sometimes, it is impossible to carry out fire tests in mines due to the danger they pose to mine workers and the underground facilities. However, understanding the potential occurrence of fires in a mine and their dynamics is critical to developing an appropriate emergency evacuation plan, fire suppression, and firefighting techniques. In this study, a numerical fire model using computational fluid dynamics (CFD) with fire dynamics simulator (FDS) 6.7.6 was developed to examine the influence of tunnel bifurcation on maximum temperature beneath a tunnel ceiling. The model was validated using full-scale experimental data. The maximum ceiling gas temperature predicted using FDS and measured maximum smoke temperature during the experiment shows good agreement. The study shows that bifurcation could lower the maximum ceiling temperature of fire-induced smoke in a subsurface environment. The findings from this study apply to the broader field of ventilation and fire life safety in tunnels and other underground environments.

Jun 23, 2024

By J. F. Oyler

One of the most important applications of material handling engineering technology occurs in iron ore pelletizing plants. Although the total installed value of material handling systems in such plants, as well as in many other modern process plants, is a relatively small percentage of the value of the plants (5 to 10% perhaps), their significance is considerable. Indeed this significance equals that of the more expensive process equipment in the plant, since the failure of any component of any system causes, shutdown of the entire plant. It is because of this increased consequence of failure that design criteria for process plants are more conservative than for conventional material handling applications. A second unique characteristic of material handling technology applied to process plants in general is the variety of materials being handled and the wide range of problems this variety presents. One extreme encountered is the stickiness of filter cake. Here the entire design effort is aimed at keeping the material flowing through transfer points and preventing it from building up on components. Another extreme is the conveying of fired pellets - hard spheres with a very flat angle of repose and abrasive characteristics severe enough to make conventional wear plate materials impractical.

Jan 1, 1976

By J. R. Goode

The first part of this paper comprises a general discussion on refractory gold ores and their mineralogy processing methods now in use are reviewed and test procedures for the important methods are discussed. Factors determining the selection of a process are outlined. The paper includes a survey of production plants using pressure oxidation, roasting and biological oxidation to process refractory ore. The status of processes under development is briefly reviewed.

Jan 1, 1993

By Donald D. Murphy

My first contact with underground, bolt conveyors came when I was hired as a draftsman by the La-Del Conveyor & Manufacturing Company in 1935. At that tine relatively few nines were using haulage belt conveyors. Wore they were in use, they were usually loaded by chain or shaker type room conveyors which in turn were hand loaded at the working face. Duo to the low room tonnage, a gathering belt might receive who output of from six to eight rooms. For several years belts 26 and 30" in width were the favorites for coal mine use. Belt speeds very seldom exceeded 200 ft. per mm. at that time. Conveyor lengths for the majority of units lay between 1.000 and 2000 ft. For a number of years 25 H.P. drives were adequate for those conveyors. From 1940 until about 1950 loads and speeds went up slightly and 40 H.P. drives became the standard. Since the majority of mines were then using direct current power systems, we were able to use controllers with 3 or more steps of starting resistance. The slow belt speeds coupled with relatively long starting cycles kept the rate of acceleration low and gave us smooth, easy starts.

Jan 1, 1963

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019

By Arthur W. T. Grimley

Hydraulic coal mining is being successfully practiced in China, U.S.S.R., Japan and Canada and in each country, excepting Japan where suitable sites are not available, the system is being expanded to either existing conventional mines or new mines. Productivity levels and economics at these mines are in all cases better than the productivities achieved in conventional mines in the same general localities. In the U.S.S.R. face productivities approaching 50 tons per man shift have been reported while in Canada the latest statistics show average face area productivity levels are in the region of 200 tons per man shift production monitor. In the United States hydraulic mining has not been actively pursued to the same degree and consequently there are no full scale hydraulic coal mines in operation or construction. Because many of the coal measures in the Western U.S.A. are generally somewhat similar to those being successfully hydraulic mined in Western Canada and parts of Siberia it is realistic to believe that successful hydraulic mines can be designed and developed in the Western U.S.A. Particularly if the vast technological base that already exists is used to improve on other people's ideas, systems, methods and equipment.

Jan 1, 1983

By Neil and Associates

Seismic tomography is one of several additions to the suite of geotechnical engineering tools for use in various underground rock and mineral geologic structures. Seismic tomography is a method for reconstructing a cross section of an object based on attributes of seismic energy that have been transmitted through the object. The in-seam seismic tomogram provides a dataset that can be graphically portrayed in a color-coded format that is then used to infer relative stress concentration (Fig. 1). During the past several years, the US Bureau of Mines (USBM) at its Denver, CO and Twin Cities Research Centers in Minnesota funded several innovative hardware and software developments. These were directed toward use of in-seam seismic tomography for underground geologic strata evaluations. These preliminary investigations have matured into well-defined and field-proven technical advances for improving ground-control decision making in the mining industry.

Jan 1, 1996

A portable electronic instrument was developed which will measure change of longitudinal wave velocity with change of uniaxial stress in rock columns. The instrument is a solid-state device powered by nickel-cadmium batteries. It uses a probe of two piezo-electric crystals spaced inches apart to send and receive a pulse through a stressed rock. A one-inch cathode ray oscilloscope visually displays the longitudinal wave. A reference chart is used to find the stress. Laboratory results have indicated that the average stress on a sandstone column can be found to within 35 psi. The feasibility of using this instrument to determine stresses in mine pillars is to be studied. The instrument may be used to investigate physical properties of rock.

Jan 1, 1970

By K. S. Radcliffe

Results are presented for the first phase of an experimental program to study the feasibility of using acoustic velocity for predicting the state of stress in a rock mass. Compressional wave velocities were determined axially in cylindrical samples during uniaxial compression for several rock types conditioned in dry and water-saturated environments. Results indicate that in rocks containing compressible voids or cracks, substantial velocity change occurs with the application of stress in the lower (below 100 MPa) stress regime. The effect norm- ally is nonlinear, however, and diminishes to asymptotic values when cracks or voids become closed or with saturation. Empirical prediction equations were derived for each rock type by linear and nonlinear regression analyses, and correlation coefficients were calculated to determine the equations that best fit the stress- velocity data. The operational range for predicting stress using compressional-wave velocity appears to be within the range of vertical stress expected in most shallow to intermediate depth mining operations (less than 1,000 m). Based on the experimental results to date and theoretical considerations, it appears that the technology can be advanced to predict in situ stress based on acoustic P-wave velocity determinations in most mining situations.

Jan 1, 1986

By Ranajit Kumar Sahoo, Shatrughan Soren, Surendra Kumar Biswal, Soumya Sahoo, Sachida Nanda Sahu

The presence of appreciable quantity of clay mineral in Indian hematite ore needs an attrition technique using screw scrubber in the beneficiation circuit to remove the ultrafine clays and avoid downstream operational problems. Spectroscopic analysis revealed that iron ore samples obtained from the Barbil region of Odisha contain a high amount of silica and alumina in the form of clay minerals (e.g., kaolinite) contributed as a loss on ignition (LOI) in the iron-making process. Iron ore fines of below 10 mm size were subjected to a laboratory-scale screw scrubber, and the effectiveness of scrubbing as well as the pelletization of the scrubbed product was investigated. The screw scrubber in the beneficiation circuit helps to remove the clay minerals, causes an increase in iron values from 63.65% Fe(T) to 66.18%Fe(T), with improved physical (CCS of 325 kg/pellet) and metallurgical (RDI of 2.24%) pellet properties.

Aug 31, 2020

By D. Keech

The Conveyor Equipment Manufacturers Association (CEMA) specification B105.1 “Welded Steel Conveyor Pulleys” adequately defines standard pulleys for most aggregate material handling applications. However, many aggregate applications demand pulleys of higher capacity and reliability than that offered by CEMA pulleys. This paper examines the CEMA Pulley Standard and pulley specifications for aggregate applications requiring greater capacity and reliability than the CEMA Pulley Standard. Higher reliability increases the uptime and has a lower total cost of ownership.

Jan 1, 2003

By S. A. Montague

In spite of the many new insulating materials, both synthetic and manufactured, that have been put on the market since the end of World War II, and notwithstanding the many millions of dollars applied to the development of synthetic mica, natural block mica1 is still a most indispensable insulator in various electronic components. It will remain so, barring some spectacular break-through in research that might provide a substitute fully acceptable as a replacement for mica in all of its superior properties. But this is not to say the future for mica is assured, or free from serious problems. Technological advances have created problems requiring a solution to be found if future requirements are to be filled.

Jan 1, 1962

By Francis J. Quinn

The Natural Gas Act, of 1938, which put interstate pipelines under the jurisdiction of the Federal Power Commission, did not place a protective competitive shield around such companies - nor does any provision of the act guarantee them a profit. Natural-gas pipelines are competitive with each other and also with the coal and oil industries. Gas distributing companies must compete not only with the coal and oil industries, but also with the electric industry. Natural gas has captured markets from oil, which had taken them from coal. Oil men contend that gas prices have: been, held to an artifically low level by regulation. The electric industry is moving into the space-heating market, which pleases the coal people because the coal industry's largest customer since losing the railroads to dieselization has been the electric companies. The coal industry is attempting to monopolize the industrial and electric generating market through government intervention, and this is being done under the guise of concern for the national welfare through advocation of a "National Fuels Policy purporting to, further the cause of fuel conservation. Such a policy is contrary to American principles and would result in the individual's loss of freedom of choice and ultimately, in less reserves of preferred fuels because of diminished exploration efforts.

Jan 1, 1961

By J. van der Walt

The Meikle Mine is located in the northeastern part of Nevada in the gold-rich Carlin Trend. First discovered in 1989, Meikle is being developed into a 2.2-kt/d (2,500-stpd) underground mine that will open during the second half of 1996. Work has already been completed on the mine’s cooling plant, a necessary item due to the high rock temperature and the hot ground water. In North American mines, there has been little need for refrigerated cooling. Therefore, Barrick needed to draw on experience from elsewhere in the world — particularly South Africa — to meet these requirements. The history of cooling mines using mechanical refrigeration dates back to the 1920s at Morro Velho in Brazil and 1936 at Ooregum in India (Dobson,1940 and Biccard, 1946). From 1940 to 1960, several cooling plants were installed on the deep level gold mines on the Witwatersrand in South Africa. These were followed by similar installations on the mines in the Klerksdorp, Welkom, Evander, Rustenburg and Thabazimbi areas. The first mine cooling plant in Germany was built during 1976.

Jan 1, 1996