Search Documents

By Philip R. Whitney

Precipitation of hydrous manganese/iron oxides in streams can be readily observed in much of the northeastern United States, and is apparently a common phenomenon in other glaciated areas (1,2,3,4). Deposition occurs when Mn-enriched ground or surface water enters the stream environment and encounters conditions of higher Eh and pH. The preferred location for deposition is in shallow, fast-flowing segments of stream; the oxides usually form as coatings on detrital material. The experimental studies of Hem(5) and a considerable amount of work on marine and lacustrine manganese nodules(6,7,8) suggest that given an appropriate substrate, deposition of manganese oxides may occur even when the water is undersaturated in Mn with respect to the oxides, due to catalysis by organisms or by silicate, carbonate, or ferric hydroxide surfaces. Once begun, manganese oxide deposition is autocatalytic (9). Studies of the distribution of oxides in various size fractions of stream sediments indicate that the thickness and prevalence of the coatings commonly increases with increasing particle size in the coarse sand and gravel size ranges. Figures 1 and 2 show a fairly typical distribution of leachable metals over nine size fractions from 62 microns up to 8-16 mm. The leaching solution used was neutral ammonium citrate with hydroxylamine hydrochloride, which effectively removes the oxide coatings without significantly attacking most silicates, carbonates or sulfides. Figure 1 shows metal content as ppm of the total sample; figure 2 shows' the same data as micrograms of metal per square millimeter of surface area.

Jan 1, 1975

The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure to roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations, and trial-and-error testing. Both prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it 'is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

By David Smith

Construction of a new transportation link frequently requires crossing under an existing highway or railroad. Although traffic diversions may permit a cut and cover structure to be built, ‘zero impact’ tunnel solutions are becoming increasingly popular. The vertical clearance between the new tunnel structure and the existing highway or tracks may be very low; sometimes less than two meters. This leaves little room for error since any ground loss can rapidly translate into surface settlement. Problems can be avoided by maintaining the stability of the tunnel face and by minimizing ground movement around the tunnel lining. This paper examines construction methods that have been used to construct short tunnels with shallow cover, and highlights factors to be considered for future projects.

Jan 1, 2005

By Montaser S. El‑Salmawy, AHMED A. S. SEIFELNASSR, Ahmed Al‑Abady, Abdeaziem M. Abdelaal, Amr F. M. Ibrahim

Iron is a key detrimental impurity in silica sands that determines their contribution to high-technology industries. Herein, a simple ecologically sound approach is investigated for iron removal from a silica sand sample obtained from the El-Zaafarana area-Egypt. The sample was subjected to a detailed microscopic mineralogical study supported by XRD and XRF characterization. The sample was beneficiated using distilled water attrition scrubbing and screening over a 25 μm sieve followed by leaching using a mixture of equal amounts of phosphoric and oxalic acids. Leaching experiments were designed and analyzed using the Box-Behnken design (BBD) methodology. A model was developed and evaluated using the analysis of variance technique to map the relationship between the residual iron oxide in the produced concentrate and selected variables such as leaching temperature, oxalic acid, and phosphoric acid concentrations. XRD and mineralogical analysis reveal that quartz is the most dominant constituent of the studied sand and other minerals such as kaolinite, iron oxide, rutile, and zircon exist in trace amounts. The head sample shows a silica and iron oxide content of 95.69% and 2379 ppm, respectively. Attrition and separation over a 25 μm sieve increase the silica content to 97.05% and decreases the residual iron oxide to 455 ppm. The final product after leaching under optimized conditions shows 99.82% silica and 55 ppm iron oxide.

Aug 30, 2022

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semigelatin dynamites, three slurry explosives and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): NO, 0.010-0.035; NO2, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1979

By A. J. Basu

Geotechnical design plays a key role in mine design. I A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches I) judgmental, based on observational and experiential facts, 2) empirical, based on empirical design formulae, and 3) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools was addressed earlier (Basu and Kuruppu, 1995). The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing structures applicable to mining geomechnics. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis application in excavation design.

Jan 1, 1996

By B. Ladanyi

An adequate knowledge of the overall behavior of a rock mass at a given site is fundamental to the satisfactory design of a rock slope. The be- havior is controlled by a variety of factors, in- cluding rock type, geological structure, stress and ground water conditions. There are essentially three lines of approach that may be used to obtain information on the in-situ rock mass behavior for the purpose of the design of a rock slope: (1) Direct measurements of rock mass properties by means ol laboratory and field tests. (2) Evaluation of rock mass properties from a study of slope failure case histories and sta- tistical information on stable and unstable natural rock slopes. (3) Evaluation of in-situ behavior of rock mass by using a physical or mathematical model technique.

Jan 1, 1980

By S. K. Sahoo, S. K. Sharma, U. K. Singh, G. S. P. Singh

This research focuses on the strata control issues in a Bord and Pillar depillaring working under the influence of dead load condition of voluminous and fragmented softcover of overburden dump material. It reports the modeling of a mine working through the FLAC 2D software under the Indian geo-mining conditions. The modeling results of an actual mine working under softcover were compared with that under the intact overburden condition to assess the influence of the soft overburden over the depillaring working. The modeling work involved progressive caving of the strata and the cyclic goaf filling following the modelsimulated occurrence of main fall and periodic caving. Mohr-Coulomb Failure criteria along with a simplified strain-softening (MCSS) model was used to study the failure and caving mechanism. Salamon’s compaction model was used to simulate compaction and resultant stress recovery in the goaf material. Comparison of the model findings was done in terms of load on supports, abutment stress, and convergence, apart from the stress redistribution and failure mechanism. The load transfer mechanism of the soft overburden was also studied for an overall understanding of the strata behavior in such workings.

Jun 16, 2020

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By H. Russell, N. DePriest, J. D. Quaranta

Valley-fill structures built of blasted rock overburden from Appalachian mountaintop surface mines pose many reclamation challenges. The steep mountainous terrain, short valley lengths, and straight stream channel profiles create significant challenges to implementing fluvial geomorphic landform design in terms of both form and function, and from a safety and constructability perspective. The fluvial geomorphic landform design approach balances erosive and resistive forces by considering long-term climatic conditions, soil types, slope profiles and vegetation types. Commercial geomorphic landform design software tools do not specifically analyze the stability and factor of safety for the computer-designed landform slopes. This research investigated slope stability parameters and factors of safety between a traditional valley-fill design with a geomorphic landform alternative. Slope stability assessments were performed on two profile geometries. Finite-element modeling of a permitted valley-fill and a geomorphic design alternative indicated that slope angle and internal angles of friction associated with the gradation of the overburden greatly affected the designed factor of safety for both designs. The geomorphic designed slopes yielded the highest factors of safety out of 14 models analyzed with all cases having factors of safety over 2.0. The high factors of safety are attributed to shallow slopes and beneficial surface and internal drainage.

Jan 1, 2014

By Neil H. Bostick

This research, sponsored at Stanford Research Institute by the Grand Junction Operations Office of the U.S, Atomic Energy Commission, was an outgrowth of the concern that presently-known ore reserves may be inadequate to meet the projected demands of nuclear power reactors. The original program at SRI was to design a comprehensive geological information system and use it to store and analyze the very great quantity of data needed to estimate uranium ore reserves. Study of the problem showed that it could be solved only by use of modern electronic data processing techniques, so such a comprehensive system was designed and tested. The system test was satisfactory, but input lead time and total expense were shown to be too great for the system to be practicable for the AEC under present circumstances. Thus, based on results of the earlier research, a specialized and simplified procedure for predicting approximate uranium ore reserves was devised. The prediction is based on general geology of specific area cells of the earth, in order to provide complete volume coverage; the strata in these ores are evaluated for uranium ore favorability on the basis of a few selected criteria in order to allow rapid data input. Since the bulk of U.S. reserves are in clastic host rocks only such strata are considered in this work. This paper describes the structure and some details of the resource system and how it was tested in rn area of the western United States.

Jan 1, 1969

By Robert A. Clifton

It seems probable that more and more minerals will be used in plastics as time goes on. This must occur because the minerals will; aid in processability, enhance the engineering properties, reduce the cost, and above all conserve large amounts of petroleum based chemicals. This paper examines the advantages and disadvantages of using the minerals and the ability of the domestic minerals industry to support this possibly very large undertaking. In the author's opinion, it can. This talk is excerpted from a forthcoming Bureau of Mines Information Circular.

Jan 1, 1985

By R. P. Gardner

Results of work on the development of a phenomenological model for the continuous flotation process using short-lived radioactive tracer techniques for the determination of model parameters is reported. A model that incorporates a flotation first-order rate constant and a residence time distribution based on the cross flow finite state (CFFS) model has been derived and investigated. The short-lived radioactive tracer techniques necessary to extract the model parameters have been developed as have the necessary nonlinear search methods. The conditions under which all the model parameters can be extracted from a single radiotracer experiment are detailed and illustrated. A microcomputer-based unique data logging system has been designed, assembled, and implemented for collecting the necessary transient radiotracer data. Results are reported for a continuous laboratory flotation system for the two systems mica ore and coal.

Jan 1, 1985

By Michel Dagbert

In the exploitation of porphyry-type deposits, the quality of the ore is mostly defined according to its grade. Besides the simplest distinction, ore-waste, several grade categories may exist and they correspond to the different ways in which the ore is further processed. At the time of mining the selection of the different categories is done from extensive information available from blast holes. But planning has to be done before this information is available and it is necessary for the geologist to forecast, from exploration and development data alone, the possible outcome of the selection done later on a block, a level, or the whole deposit and ultimately predict the ore reserves and value of the deposit. A good statement of this problem has been presented at the 1976 AIME annual meeting by Williamson and Hueller (1976). They have shown that, if the cut-off values are directly applied to the estimated grade of blocks, a gross overestimation of the recovered tonnage of ore (14%) will occur. This problem, now termed "the vanishing tons problem" (DaVid, 1977) seems to be common in many open-pit operations and it has been explained several times (DaVid, 1972; Huijbregts, 1975). In order to solve it l.Jilliamson and Mueller proposed a solution based on compiling masses and masses of blast hole data available from mined-out portions of the deposit. They derived empirical correction factors which provide for every block, given its estimated grade, the expected tonnage and average -grade of each category of material within that block. The purpose of our work is to repeat the same exercise but ignoring the blast holes data i.e. we want to derive the correction factors from the only DOH data. Doing this, we are more in the real conditions where the valuation of the mine and are reserve analysis has to be made before production actually starts. Two possible ways to achieve this goal will be investigated and the emphasis will be on recently

Jan 1, 1977

By S. Rupprecht

"This article addresses the prevalence of poor public reporting practices of coal exploration results, coal resources and coal reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or saleable tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal — therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (ROM) and saleable coal tonnage, their associated qualities and other material and relevant information.Competent or qualified persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provided. “Companies are encouraged to provide information in their public reports, which is as comprehensive as possible (CRIRSCO, 2013).” However, too often this isn’t the case, and material matters are either not reported or inadequately disclosed.According to the South African National Standard (SANS) 10320:2014 draft document, “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the saleable coal reserve must be stated. The moisture basis of reporting shall be stated.” An example as to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are detailed in the followint paragraphs. The Kendal power station, commissioned in 1988, operates at a calorific value (CV) range of 19 to 20 MJ/ kg, an ash content between 29 and 34 percent and volatiles between 20 to 21 percent. Other power stations, such as Kriel or Hendrina, may require different qualities, such as a CV range of 22 to 23 MJ/kg, an ash content between 20 and 28 percent and volatiles between 22 to 23 percent. Thus, in terms of domestic saleable coal, it is not just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station (Chetty, 2010).” Sulfur content is another important quality with the ideal coal content having a quality of less than 1 percent sulfur."

Jul 1, 2019

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize productivity, the influence of reclamation parameters must be well understood ? which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass appraisals, and also the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, we use biomass production experimental plots on reclaimed mine sites established by the Powell River Project (PRP) for a comparative study between satellite measurements of Normalized Difference Vegetation Index and inventory estimates of biomass under a variety of conditions. The PRP is a unique public-private partnership in the coalfields of southwestern Virginia dedicated to enhancing beneficial use and environmental protection of mined lands.

Feb 27, 2013

By S. Lin, Y. J. Wang

Based on systematic definitions of a generalized multiple fan ventilation system, the concepts of an augmented system, its solution curve and the operating points of the original system are introduced. The Quasi-Newton algorithm is applied in combination with the switching-parameter method to ensure a continuous search along an augmented-system solution curve and identify all the possible system operating points on it. Two example networks are analyzed to demonstrate those concepts and the application of the algorithm for identifying operating points of multiple fan ventilation systems.

Jan 1, 1994

By RIINA SALMIMIES, Paula Vehmaanperä, Antti Häkkinen

The dissolution of iron oxides in mixtures of acids is fairly uncommon but can result in a more efficient dissolution process. The objective in this work was to investigate the dissolution of synthetic hematite powder in mixtures of oxalic and sulfuric acid. Experiments were done at different acid ratios and temperatures. An increase in temperature from 15 to 35 °C increased solubility, whereas an increase from 35 to 50 °C did not change the solubility but had a profound effect on the kinetics. An important finding was that oxalic acid advanced the dissolution process since increasing the amount of oxalic acid in the system resulted in faster kinetics and higher solubilities. The dissolution kinetics were well described with the Kabai model, which was the only studied model able to describe the whole reaction time. However, the solid specific constant a varied for the different acid ratios and this is argued to be a result of changes in the solid phase. The changes in the constant a were not in line with the original study of Kabai, which indicates that a cannot be the solid specific constant but it can be the constant connected to dissolving media describing the changes in the dissolution mechanism.

Sep 23, 2020

By Arcy R., D&apos George

Removal of S02 from smelter gases is being investigated, using an innovative technique that results in the almost simultaneous recovery and production of elemental sulfur. S02 is removed from the gas stream by scrubbing with suitable aqueous salt solutions or high-boiling organic fluids. The S02-laden liquor is then reacted with H2S Crystalline, high-purity sulfur is instantly precipitated and, after filtration, the regenerated liquor is recycled. The H2S required for the process is produced by reacting a portion of the recovered sulfur with hydrogen or with methane and steam. The chemistry and results of preliminary laboratory research are discussed.

Jan 1, 1969