Search Documents

By Henning E. Soderberg, Robert Brien, O&apos

Coal may be the answer to US energy problems, but it also has its drawbacks. If it is crushed, screened, dumped, or moved, the environmental engineer is faced with a dust problem. To control coal dust, at both minimum initial cost and reasonable operating cost, demands a working knowledge of dust control equipment design, as well as the coal handling operation. Here are some guidelines to reduce air volume requirements and cut overall system costs.

Jan 10, 1981

In the dimension stone industry, workers in processing shops may be exposed to harmful levels of respirable silica dust when conducting the different tasks in stone preparation, which include cutting, grinding, polishing, and thermaling. To protect workers from this health hazard, operators sometimes ventilate processing shops using fan-powered dust collectors to capture and filter dust. To investigate this issue, NIOSH, Pittsburgh Research Laboratory, in cooperation with a dimension stone operation, upgraded an off-the-shelf dust collector the operator was utilizing in a polishing/cutting shop. Initial dust surveys showed that the unit was under-designed for the amount of dust being generated in the shop. The objective of the research was to cost-effectively increase the air cleaning volume and improve dust capture efficiency of the unit with a larger motor and blower. The unit?s original stock 0.56 kw motor and blower was replaced with a 2.24 kw motor and matching blower to increase airflow. The unit was evaluated both in the laboratory and the shop before and after the retrofit to determine the improvement of the upgrade. The study showed that the 2.24 kw upgrade improved the performance over the original 0.56 kw motor resulting in more dust being cleaned from the ambient air in the shop. The 2.24 kw unit cleaned 19% more air and captured 32% more respirable dust than the 0.56 kw unit.

Jan 1, 2009

By H. Lowers, B. Van Gosen

The Iron Hill (Powderhorn) carbonatite complex is a 31 km2 alkalic intrusion located about 35 km south-southwest of Gunnison, Colorado. The intrusion has been well studied and described because of its classic petrology and architecture of a carbonatite-alkalic complex. The complex is also noteworthy because it contains enrichments of titanium, rare earth elements, thorium, niobium (columbium), vanadium, and deposits of vermiculite and nepheline syenite. In particular, the complex is thought to host the largest titanium and niobium resources in the United States, although neither has been developed. It may be economic to extract multiple resources from this complex with a well coordinated mine and mill plan.

Jan 1, 2007

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By Jon Hurt

INTRODUCTION The entire scope of new facilities for Lake Mead Intake No. 3 includes a sub-merged intake structure, a deep tunnel beneath Lake Mead, a tunnel access shaft, Intake Pumping Station No. 3, and connections to an existing intake and water treat-ment facility, as shown in Figure 1. In March 2008 Vegas Tunnel Constructors (VTC), a joint venture of Impregilo SpA and SA Healy were awarded a $447m Design-Build contract by SNWA for a section of this work (Contract 070F 01 C1), including the 185 m deep tunnel access shaft, the 4.7 km long, 6.1 m diameter tunnel and the submerged intake. Arup, supported by Brierley Associates, is the Design Engineer for VTC. The scope of the work is shown in Figure 2. This paper will describe the design and construction on this contract, with a focus on the access shaft which is the most complete section of the work. The shaft is being sunk using drill-and-blast methods with the finallining placed as excavation proceeds. The shaft passes through a major fault zone, and extensive pre-excavation grouting for water control is required for much of the depth of the shaft.

By Isabelle Lamb, Manfred K. Lechner, Daniel N. Adams

Sydney Australia’s M5 East Motorway connects southwestern suburbs to the airport. Central to the project are twin 3.8 km roadway tunnels which are mostly driven through rock. In order to come up with the winning tender, the project team developed several unique approaches for tunnel excavation and support. The project’s flat roof with thin shotcrete lining, 20 m wide underground intersections, thixotropic-grout sheathed rockbolts and cablebolts, and new shotcrete testing methods all differ significantly from traditional concepts. This paper presents the design basis and construction methods used to achieve the 100-year design life required by the project’s owner.

Jan 1, 2001

By David E. Siskind

The Bureau of Mines has studied the problem of cracking in residential structure walls from vibrations produced by blasting in surface mines. Direct observations were made of blasting damage consisting primarily of cosmetic cracking in plaster and gypsum board walls. Measurements of structure response and also application of the response spectra analysis single-degree-of-freedom model were used to quantify the frequency dependence of the safe level criteria. An overall summary analysis was performed using the new Bureau of Mines damage observations and data obtained from nine previous studies, including the three analyzed earlier by the BuMines for Bulletin 656, published in 1971. Separate analysis of the high- and low-frequency damage cases, structural response, and two types of construction resulted in the establishment of safe vibration levels ranging from 12 mm/sec to 50 mm/sec (0.5 in/sec to 2.0 in/sec).

Jan 1, 1980

By R. L. Grayson, F. Giana, R. Aspinwall

Small-mine and contractor Fatal Incidence Rates have been a problem for over 20 years in the coal industry, and the rates persist as unacceptably high. This paper briefly retraces historical information and data on the continuing problem and recounts the many unsuccessful efforts and initiatives to address the problems effectively. Next the results of a review of international literature on addressing the problems are presented. After focusing on a method to pinpoint the trouble spots more specifically through a nested data analysis, suggestions are provided on how the problem may potentially be addressed more systematically and effectively in the U.S.

Jan 1, 2006

By W. Kracht

Frothers are surfactants used in floatation to aid generation of small bubbles. Studying events at the moment of bubble creation is a challenge because of the short time frame. This presentation introduces a novel acoustic approach. The technique has the resolution capable of detecting events that occur within 1-2 ms. The transition from coalescence to non-coalescence is tracked as a function of surfactant concentration and gas rate through the capillary. Results are given for some common flotation frothers and n-alcohols (C4-C8). A stress model is used to give a qualitative explanation to the observed action of frothers on coalescence prevention. Results for salt (sodium chloride) are included for comparison).

Jan 1, 2009

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Carmen Scalise, Miquel Sanchez

"The McCook Main Tunnel system consists of a 10-m (33-ft) finished diameter, 490-m (1,600-ft) long, hard rock tunnel constructed from a 27.5-m (90- ft) diameter and 92-m (300-ft) deep main gate and tunnel construction access shaft. The gate shaft houses six, high-head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steellined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir.The construction of the tunnel system has been divided into two contracts. The gate and construction access shaft was completed in August 2011. The tunnel excavation and concrete and steel lining was completed in September 2014. The remaining and undergoing construction include the tunnel connections to the reservoir and the Mainstream Tunnel and installation of gates and hydraulic cylinders. This article focuses on the live connection of the McCook Main Tunnel to the Mainstream Tunnel that was initiated in November 2014 and will continue through the seasonal drier weather conditions in Chicago approximately from October through April. Chicago TARP systemThe MWRD has been addressing combined sewer overflows (CSO) and flooding in Chicagoland since the late 1960s and formally adopted the tunnel and reservoir plan in 1972 to protect the region’s most precious drinking water supply, Lake Michigan. Phase I of TARP, which included construction of 175 km (109 miles) of deep storage and conveyance tunnels with diameters up to 10 m (33 ft), was completed in 2006. In addition to protection of Lake Michigan from CSO discharges, Phase I resulted in substantial improvements in surface water quality as well as the quality of life for lake and riverfront communities in Chicago. Water quality improvements and flooding mitigation will be further enhanced as Phase II reservoirs are placed in service, including the three large reservoir systems, McCook, Thornton and Majewski (Fig. 1).The McCook Reservoir is the largest reservoir in the TARP system. Once completed, this $700-million reservoir facility will receive 38 billion L (10 billion gal) of CSO and flood water via the McCook Main Tunnel, which connects the TARP Mainstream Tunnel to the McCook Reservoir, and from distribution and Des Plaines inflow tunnels which will bring flow from the Des Plaines Tunnel of TARP."

Sep 1, 2016

By Donald A. Brobst

Barite, the sulfate of barium, occurs in many geological environments in sedimentary, igneous, and metamorphic rocks. The commercial deposits of barite may be classified into three major types. 1. Vein and cavity fillings that occur in rock fractures, along bedding planes, and in various solution structures. 2. Bedded deposits in which barite occurs as the principal mineral or cementing agent in stratiform bodies in sedimentary rocks. 3. Residual deposits occurring in unconsolidated material formed by the weathering of preexisting rocks. The geologic characteristics of each type of deposit are of fundamental importance to the successful search, development, and economic use of barite deposits.

Jan 1, 1980

By G. Deschênes

In Part I of the work, gold and silver were shown to be efficiently extracted from Kupol samples using lead nitrate in a cyanide leach system. In Part II, a comparison of the technical and economic merits of a new technology called CELP (CANMET Enhanced Leaching Process) was made with the cyanidation/AVR(Acidification-Volatilization-Recycling) process using 8 metallurgical variability samples as well as a large composite sample which represented initial two years of Kupol mill feed. The composite sample had 33.4 g/t Au and 289 g/t Ag. The metallurgical demonstrated that the CELP produced very similar gold and silver leach extractions compared to the standard Cyanidation /AVR leach conditions at 1/2 the cyanide concentration (1000 ppm NaCN in CELP vs. 2000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton, were approximately the same for the two technologies (total cost of the CELP with the use of Merrill-Crowe at $46.48/ton, with cyanidation/AVR at $46.13/ton). However, the implementation of the CELP would eliminate a capital expenditure of approximately $5 million. Eight variability samples used to confirm the previous results showed that on average the gold and silver leach extractions with the CELP and the feasibility leach conditions were very similar for gold extractions, but 4.6% higher for silver extractions compared to the conventional cyanidation. The decision was made to remove AVR cyanide recovery from the Kupol flowsheet and implement the CELP at Kupol. The ability to use conventional leach equipment with the CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2009

By V. Izaxon

Current practice in mining frozen, underground placers is to support the mine openings by leaving remnant pillars, which are kept frozen to maintain their stability. These pillars may be partially extracted depending on mining conditions, but this practice may be risky, and roof falls are common. Instead of allowing the mined-out areas to cave, the extracted entries could be filled with waste material, which would then be frozen, using cold ventilation air. A finite difference model for analyzing the effects of various parameters on the freezing of backfill in underground mines in the Arctic has been developed and tested. The model also accounts for properties unique to a frozen rock mass, including those that change with temperature. Examination of the characteristics of ice-cemented mining waste materials as backfill indicates that with proper engineering control, a backfill system can be designed for use in production mines. The system will allow increased extraction ratio while maintaining the stability of underground openings with minimum heat impact on the surroundings. These simulated results establish the relationships among the strength, the temperature, and the freezing characteristics of a given material. When coupled with site observations these relationships will facilitate the optimal design of ore pillar recovery methods.

Jan 1, 2004

Ventilation network modeling in mine planning dates back at least three decades, but it is not widely accepted and/or practiced until the last decade, thanks to the advent of modern computers with their increase d speed and storage space. There are at least half a dozen such modeling software packages available on the market each with different features and acceptance. This paper compares five popular software packages,?? VnetPC Pro, MineVent, VentSIM Visual, VentGraph and MFIRE 3.0. A case study using Missouri S&T?s Experimental Mine is conducted to compare the five software packages in features, interface, output display and user-friendliness.

Jan 1, 2012

By J. Kretschmann

"By the end of the 1950s, the German hard coal mining industry produced 150 million tons of hard coal per year in 170 collieries with 600,000 employees. At that time, 70% of the primary energy demand of the Federal Republic of Germany was covered by domestic coal. However, due to coal mining becoming an increasingly globalized business and the oil and gas industry producing with lower costs, the German domestic hard coal industry stood constantly under restructur-ing pressure. The industry declined until the end of its life cycle. In 2007, a political understanding was arranged to phase out German hard coal mining in a socially acceptable manner by the end of 2018. This decision required a new strategy for the coal mining industry. Being strictly finalized, the German hard coal mining industry has to be prepared for the post-mining era. To create a sustainable development strategy, the long-term impacts of coal mining activities in Germany concerning the environmental, economic and social dimensions will be analyzed systematically and forward-looking. The regional and social responsibility during the closing process and for the post-mining era will be emphasized. High technical standards in environmental protec-tion and post-mining technologies, as well as long term experiences in the development of former mine sites to create new jobs are significant from an international point of view. The traditionally constructive social partnership between employers, union, and employees has enabled long-term stable adaption processes and avoided social friction. The sustainability strategy of the German hard coal mining industry can be regarded as a role model for other mining countries and regions facing similar transition challenges. INTRODUCTION Principally, mining is a finite business that reaches its end if the deposits are depleted or the raw materials can no longer be mined in an economically profitable way. However, the impact of mining is po-tentially an infinite one – at least if you measure it at a human time scale. Mining always means interfering with geological and ecological structures that cannot be reversed to their original condition. In general, the mining cycle (Figure 1) can be divided into three phases: 1. The exploration phase, in which the deposit is investigated to determine its technical and economic profitability. The period of these undertakings is relatively short and can lead to the launch of mining operations. 2. What follows is the actual mining phase which usually lasts for a long time and ends latest when all deposits are fully depleted. This lifespan may be shortened if the economic conditions (production cost or market price) deteriorate. Nevertheless, mining may be resumed if those conditions become favorable once more (examples are silver mining in Germany or rare earths mining in the USA). 3. The longest phase, however, is the post-mining phase as the human interference into geology and nature is usually inten-sive and irreversible. Mining can lead to consequences which have a permanently adverse impact on people and the environment; therefore, they have to be managed as best we can (1)."

Jan 1, 2017

By Staff

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several stages—basic (mining), intermediate processing, manufacturing of finished goods and construction. The estimated growth rate for the real GDP of the United States for 2006 was 3.2 percent. The nominal GDP was about $13.2 trillion. The value of minerals mined in the United States in 2006 rose significantly because of increased unit price for some metals—particularly copper, zinc and other base metals. There was also a significant reduction in metals stocks. Infrastructure expansion and manufacturing in China and India have been absorbing a significant portion of world output. Domestic production increased for some industrial mineral materials, mainly cement and construction sand and gravel. Production of crushed stone declined less than 1 percent in 2006 compared

Jan 1, 2007

By Tim O’Neil

Tire companies have historically used the mining industry as a platform to launch new technologies. And the mining industry has been receptive to that. So, while developing its Two Piece Assembly, Goodyear noted a number of trends in the mining industry: •The global market sophistication of equipment and operations requires the packaging of products and services to provide the best return on investment. •Industry consolidation and growth have resulted in fewer, more powerful mining houses, leveraging purchasing power in the marketplace. •User productivity demands continue to drive original equipment manufacturers to develop higher pay-load equipment. •Technology needs include improved ergonomics, to reduce fatigue and increase operator productivity. •Increased laws and environmental regulation prohibit on-site whole tire disposal practices.

Jan 1, 2003

By G. Hoffman

Sustainable development has brought social, environmental and energy efficiency concerns together with management and governance of natural resources. Cement manufacturing, an energy- and natural resource-intensive industry, is adapting to meet sustainable development goals. Emission standards for cement plants and increasing energy costs have lead to changes in the use of natural resources and recycled materials. Utilizing pozzolans or supplementary cementitious materials (SCMs) as mineral admixtures in blended cement or as a substitute for cement in concrete lowers energy costs and CO2 emissions. Although the western U.S. is rich in natural pozzolans, artificial products, particularly fly ash, have greater use as mineral admixtures. Pozzolans and SCMs have many beneficial properties, such as preventing alkali-silica reactivity, a common problem in the western U.S. Barriers exist for mineral admixtures in the cement and concrete industries because of past inconsistencies in quality or availability. New environmental regulations on the primary industries producing artificial mineral admixtures could adversely affect the quality and quantity of these materials in the future.

Jan 1, 2009

By T. Johnson

Mining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel, cobalt and uranium have been particularly active. The world?s largest nickel mine ? the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale?s Voisey Bay mine in Labrador. Voisey?s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $1.4 Billion Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 ? 250,000 MT/yr manganese carbonate.

Feb 27, 2013

By Hassan El-Shall

Treatment of plant effluent including waste water and associated soluble and insoluble substances, is of a primary concern of many process industries including mineral processing operations. The major objective of such treatment is the removal of such impurities which can interfere with the process through the use of recycled water, and/or to comply with environmental ordinances. For example, Ramirez and Clements (1978) state that molybdenum contents in the range of 19 mg/1 eventually poison ion exchange resigns used for the extraction of uranium. In addition, recent restrictions by the EPA on molybdenum discharge values for mining waste water necessitate removal of this metal to (0.5-1.0 mg/1).

Jan 1, 1984