Search Documents

By Durell Denysschen, Rafael Abela

The recovery of gold from old mine dumps has been carried out over the last two decades. The gold value and price together with recovery methods, determine whether it is economical to process a dump. Pre-concentration with cyclones and spiral concentrators may offer a method to process dumps considered currently uneconomical to treat.

Jan 1, 2006

By E. S. Peters, M. J. van Rensburg, M. Le Roux, Q. P. Campbell

"The demand for energy has continued to rise worldwide in line with population growth. The majority of South Africa’s electricity is supplied by coal-fired power stations. The amount of fine coal (-2 mm) generated at coal processing plants has increased, due mainly to mechanized mining methods. Fine coal retains more water, which lowers its heating value.Drying the coal is costly and it is difficult to achieve the required moisture content. Consequently, coal fines are often discarded. An estimated 8% of the total energy value of mined coal is lost1.Fluidized bed technology is often used to dry coal thermally, but this method is expensive and has an adverse environmental impact. The objective of this study was to investigate the removal of moisture from fine coal (<2 mm) in a fluidized bed operated with dry fluidizing air at moderate temperatures as the drying agent. The effects of different air temperatures and relative humidity levels were investigated in a controlled environment. The study further investigated the influence of coal particle size on moisture removal.The drying rate was found to increase with increasing temperature. The relative humidity of the drying air had a more pronounced effect on the drying rate, even at temperatures as low as 25°C.. It became more challenging to remove moisture as the particle size decreased. The gain in calorific value was greater than the energy required to dry the coal samples, showing that a fluidized bed using moderately warm dry air is an energy-efficient drying technology. The energy efficiency of the fluidized bed compared favourably with other thermal drying methods.Paper written on project work carried out in partial fulfilment of Degree in Chemical Engineering(NWU) - Pursuing Masters in Coal Beneficiation"

Jan 1, 2015

By P. J. Hancox

Heavy mineral deposits have been known from Liberia since the1950s from both river and beach placers. The heavy mineral content of beach sands ranges between 28?62% and the suite includes ilmenite, rutile, zircon and magnetite. These occur together with kyanite, sillimanite, staurolite and garnet. The average ilmenite content is 82% with minor zircon (11%), rutile (6%) and monazite (1%). The ilmenite is, however, of poor quality with haematite intergrowths and a titanium content ranging from10?42.4% (average ±25% TiO2). The amounts of rutile and zircon, while of suitable quality, have also previously been deemed too low for economic exploitation.

Jan 1, 2000

By D. H. Diering

The paper takes the reader into the depths of a modern ultra-deep South African gold mine and gives a perspective on the vertical and horizontal extent of the tunnel networks in such a mine. Depending on the mine design layout employed, tunnels once excavated are subjected to various levels of stress change over their life time, and the support requirements are explained. It is suggested that shotcreting is the only viable ultra-deep level support medium, and after looking at the latest developments, the logistical problems are put forward. In an effort to overcome most of these problems, the South African ultra-deep mining industry embarked on a collaborative research programme in 1998. The importance of tunnelling and in particular tunnel support as a critical technology for future successful ultra-deep level mining is stressed. While not yet fully ?on top of? these problems and challenges, our industry is now fully addressing them and we expect to make significant progress during the next 4 to 5 years.

Jan 1, 2000

By C. D. K. Gauert

High-pressure waterjet technology is proposed as an alternative tool for selective underground mining of high-grade ore sections in stratiform orebodies showing a preferred ?bottom? or ?top? enrichment such as the Witwatersrand reefs and the Bushveld Complex platiniferous reefs. This technique, utilizing known mining technology together with more advanced machinery and additives as used in industrial and cleaning applications, may lead to an increased life-of-mine (LOM) for mining operations. A series of experiments was successfully carried out in a laboratory on Witwatersrand quartzite material, indicating acceptable cutting performance. Mining volumes by selectively cutting of reef portions are considered to be comparable to traditional drilling and blasting. Economic advantages of waterjet mining include energy savings due to the lower quantity of gangue rock to be hoisted to surface, as well as savings by a decrease in the usage of blasting materials. Capital expenditure of waterjet cutting, if applied on a broad scale, could be lower in the long term than that of conventional drilling and blasting methods. Mining by the application of high-pressure waterjet technology could become a competitive ?green technology? improving the economics and safety of labour-intensive mining operations. This paper suggests that waterjet cutting at an industrial scale can become a routine hard-rock mining technique in the future. Keywords waterjet cutting, high pressure, mechanized narrow reef mining, abrasive agents, costs, selective mining.

Jan 1, 2013

By B. H. Kim, S. K. Chung

RMR, Rock Mass Rating, is one of the famous rock classifications. However, RMR was proposed empirically and absolutely depends on the experience of engineer. Therefore, engineering verification is needed for RMR system itself. In this study, the factor analysis and the multiple regressions were performed in order to evaluate the validity of rating factor of RMR. Also numerical analysis was carried out using the FLAC based on Taguchi method, a kind of robust designs, in order to examine the support of tunnel corresponding to the revaluated RMR. As the result of the analysis new RMR was proposed with five minimized factors of intact rock strength, RQD, spacing, persistence and roughness of discontinuities. RMR est un des procédés de la classification du roc qui sont généralement utilisés. Mais RMR s&apos;appuie sur l&apos;expérience et se absolument soumet à l&apos;expérience d&apos;ingénieur. Il est donc nécessaire de vér- ifier techniquement sur le système de RMR. Dans cet étude, on met à exécution l&apos;analyse du facteur et la régression multiple pour évaluer la convenance de la cause de classification de RMR. De même, pour évaluer le support du tunnel selon RMR réestimé, on a exécuté l&apos;analyse de la valeur numérique par FLAC qui se base sur la lois de Taguchi, laquelle est une sorte de système du plan robuste. Selon le résultat de la régression multiple, il est proposé de nouvel RMR à partir de l’intensité de roc intact, RQD, l&apos;espacement, la persistance et la rugosité RMR ist eine der weit benutzten klassifikationen fuer die felsenstuecke. Da aber RMR erfahrungs- maessig ist und ueberwiegend von der persoenlichen Erfahrung eines Ingenieurs entschieden ist, ist es mit Sicherheit notwendig, das RMR-system selbst technisch zu ueberpruefen. In diesem studium waren die faktorenanalyse und mehrfachregressionanalyse durchgefuehrt, um die gerechtigkeit der klassifikationenfaktoren von RMR zu bewerten. Ferner war noch eine numerische analyse mit ben- utzung von FLAC aufgrund der Taguchi-methode, eine art technik der robust design, eingefuehrt, um die tunnelstuetze infolge der neubewertung von RMR unterzusuchen. Gemaess der mehrfach regression analyse wurde eine neue RMR, die sich aus 5-eingeschraenkten faktoren wie intact rock strength, RQD, spacing, persistence und roughness von discontinuities zusammensetzen, in vorsch- lag gebracht

Jan 1, 2003

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By J. M. Cardoso, E. F. Quadros, A. Chiarini, F. Fernandes, G. Vilela, J. Ireno, L. C. Agostini

Based on the geological-geometric characterization of the basaltic rock at the site of a factory for chemical products situated in the Southern region of Brasil, and on results of a significant number of packer tests, the principal directions of flow were estimated, taking into consideration the intersection and the orientation of the joints and the amount of contaminant flow measured in each interval. The tests were performed using the multi-packer hydraulic multitest probe of IPT (HMTP) instrumented with an electric conductivity meter. A method of analysis for three-dimensional evaluation of the amount of contaminant flow in the area was proposed for future mitigation of the problem. Basé sur une caractérization géologique-géotechnique de la roche basaltique existant sur un site dune fabrique de produits chimiques située au sud du Brésil et sur les resultants dún nombre significantif déssais du type packer, les directions principales d´écoulement ont été estimées en considerant l´intersection et orientation des joints et la quantité de contaminant mesurée sur chaque intervale d´essais. Ceux-ci ont été realizes en utilisant une sonde multipacker developée au IPT – São Paulo (HMTP) instrumentée avec un mesureur de condictivité électrique. Une méthode d´analyse 3-D pour l´évaluation du transport du contaminant sur ce site a été proposée pour une future mitigation du problème. Auf Grund der geologischen Struktur des Basalts auf dem Gelände einer chemischen Fabrik in Südbrasilien und der Ergebnisse einer ansehnlichen Zahl von Pumpversuchen wurden die Hauptfließrichtungen bestimmt unter Berücksichtigung des Kluftgefüges und der in jedem Intervall gemessenen Menge kontaminierten Wassers. Die Versuche erfolgten mit dem im IPT entwickelten Verfahren (HMTP) mit Mehrfachpackern und elektrischen Leitfähigkeitsgebern. Ein analytisches Verfahren zur dreidimensionalen Ermittlung der Mengen kontaminierten Wassers wurde für die künftige Befassung mit dem Problem entwickelt.

Jan 1, 2003

Power Point Presentation

Jan 1, 2007

By A. P. I. Popoola

Laser coatings are used for a wide variety of applications. TiB2/Ni intermetallic matrix composite coatings were fabricated on Al-substrate by a high power Rofin Sinar Nd: YAG solid-state laser. The characterization of the coatings was carried out by optical microscopy (OM), scanning electron microscopy (SEM/EDS) and X-ray Diffraction (XRD). Electrochemical study of the laser coatings in 3.65 per cent NaCl at room temperature revealed that with very high weight proportion of nickel the corrosion resistance of the coatings deteriorated due the presence of AlB10 phase. 50 wt per cent TiB2+50 wt per cent Ni laser coatings exhibited the highest corrosion resistance in test solution. Keywords Corrosion, protective film, laser surface alloying, reinforcement.

Jan 1, 2011

By C. Machio

This paper reports the results of a study to determine the effect of process control agent (PCA) on the characteristics of Ti-Mg powders during milling. It has been shown that a 2% increase in PCA content leads to up to a 40% increase in yield of the milled powder but reduces the kinetics of the mechanical alloying process. The introduction of 4% PCA decreases the mean powder particle size by up to 30%, whereas 6% PCA increases the mean particle size by up to 230%. The characteristics of the milled powders will be discussed in relation to the role of PCA in the milling process. Keywords Titanium?magnesium, mechanical alloying, PCA.

Jan 1, 2011

By A. Kale

A chlorination pilot plant having capacity to produce 5?10 kg/hr of titanium tetrachloride is in operation at the chlorination facility in Mintek. The bubbling fluid bed chlorination plant can be operated in batch and/or continuous process to study the chlorination kinetics of various feedstocks. The chlorination of titaniferrous ores to produce titanium tetrachloride (TiCl4) was carried out during the commissioning of the pilot plant and also as part of the titanium programme carried out at Mintek. TiCl4 is a basic raw material for producing commercial titanium dioxide pigment and titanium metal. This paper discusses the challenges faced during the commissioning and operation of the chlorination pilot plant. It also discusses the effect on the auxiliary facilities and instrumentation as a result of the harsh operating conditions of +1000°C and use of corrosive gases like chlorine and titanium tetrachloride. It discusses the effect of physico-chemical properties of the titanium tetrachloride and iron chlorides. The effect on the chlorinator refractory lining due to heating and cooling of the chlorinator is also discussed. Besides the special provisions made during the design of the chlorinator, this paper also discusses the operational experience and possible solutions to be implemented in future. Keywords Fluid bed chlorination, titanium ore chlorination, titanium tetrachloride (TiCl4) production using fluid bed technology.

Jan 1, 2011

By Antonio Karzulovic, Sergio Olavarría, Patricio Adriasola

The economical analyses of different Chuquicamata open pit mine planning scenarios, indicate that the pit closure should occur at latest in the year of 2017. However, about 60,000 m of drill holes have demonstrated that below the pit bottom there is a potential of 2.3 billion tons of ore. Hence, Division Codelco Norte developed the scoping engineering for a large underground panel caving operation, similar to El Teniente mine. This project considers the exploitation of a 2500 m 300 m footprint, with three 250 m lifts. The plan considers to initiate the construction in the year 2009, to begin the production in the year 2015 and achieve a production rate of 45 million tons per year in the year 2021. A large-scale transition from open pit to underground mining like this one presents three main challenges: (1) to include the geotechnical aspects relevant for mine design and mine planning, (2) to define the proper surface and underground infrastructure, and (3) to fulfil the project deadlines and to achieve the production targets. This paper summarizes this transition project and discusses these three main challenges.

Jan 1, 2006

Control of flotation processes is mostly managed by plant operators, who assess the performance of the plant based on their own experience and other heuristic rules. These rules tend to be subjective or ill-defined, since most of them are concerned with the structure of the flotation froth, such as colour, bubble size and shape distributions, froth mobility and froth stability. These phenomena are very difficult to quantify objectively, and inexperience on the part of the operators, human error, etc., can lead to significant inefficiencies in plant operation. In this paper the development of a fuzzy system to support the control decisions of plant operators is described, which leads to significantly smoother control action and more stable plant operation than could be obtained with crisp sets of rules or manual control strategies. Keywords: flotation, fuzzy logic, image analysis, genetic algorithms, rule induction

Jan 1, 2000

By E. Matinde, S. L. Msibi

"The robust nature of alumina refractory materials presents opportunities for their in-process reclaiming and re-use in non-critical applications. Virgin refractories can be substituted with different quantities of reclaimed materials without compromising the quality of the refractory products. In this study, the effect of reclaimed bauxite on andalusite-containing refractory castables for tundish applications was investigated. The recycled bauxite was formulated in different proportions to replace virgin andalusite in the castables. Standard tests were conducted to evaluate the physical, physicochemical, and thermochemical properties of the formulated products. Static corrosion tests were conducted using tundish slag in order to simulate the actual operating conditions. The results show that the standard flow behaviour, open porosity, and bulk density of samples containing up to 22 mass% reclaimed bauxite were comparable to those of the reference castable. However, high-temperature properties such as static corrosion at 1400°C and hot modulus of rupture at 1500°C indicated that there is an upper constraint to the amount of substitution. The study demonstrated direct potential savings of up to 10% when the reclaimed alumina replacement ratio was increased to 22 mass%. IntroductionAlumina-based refractories can be classified into low-alumina, containing less than 50% Al2O3, and high-alumina or bauxite, containing between 50 and 90% Al2O3. High-alumina refractories have widespread applications in high-temperature metal extraction processes due to their outstanding thermochemical and thermomechanical properties and stability (Rebouillat and Rigaud, 2002; Frulli, 2016). The typical chemical composition of refractory-grade bauxite consists of 85–90 wt.% Al2O3, 5–10 wt.% SiO2, 1–2wt.% Fe2O3, 3–4 wt.% TiO2, 0.4–0.8 wt.% CaO + MgO, and 0.20–0.8 wt.% K2O + Na2O (Nyoka et al., 2013). The thermochemical and thermomechanical properties of bauxite-based refractories rely principally on the conversion of the contained silica and alumina to the highly stable corundum (?-Al2O3) and mullite (3Al2O3· 2SiO2) phases (Rebouillat and Rigaud, 2002; Hill and Sehnke, 2006; Garbers-Craig, 2008; Frulli, 2016)."

Jun 1, 2019

By J. Daavittila

In the latter part of the 1980s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming too inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result, the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation, an application for FeMn production was developed. Now as the Tornio FeCr-plant is considering expansion, the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand for better working conditions. The possibilities of resolving to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control the process, even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

By M. Handley

The Witwatersrand Basin contains by far the most gold ever found, and has hosted mining from its discovery in 1886 to the present. For many years, South Africa was the world’s largest producerof gold, nearly all of which came from the Witwatersrand. Since 2000, South Africa has fallen back several positions because of declining gold output. There are many complex and varied reasons for this; however, declining gold resources in the Witwatersrand Basin are not one of them. As far as the author knows, there are no qualified estimates in the literature of gold remaining in the Witwatersrand Basin. This paper collects mining data from several sources and then, using elementary gold accounting and error analysis, attempts to estimate the amount of gold remaining in the Witwatersrand Basin. It includes gold underground in existing and defunct mines, in evaluated ore resources, and dumps. Compiled data from 1887 to 2019 shows that 50 200 t of gold were produced by Witwatersrand mines, while it is estimated that a further 48 100 t remainunderground, both within and outside of mine leases, a further 1 600 t on the surface in tailings,and an unknown amount in rock dumps. Nearly all of this gold will remain inaccessible with current mining methods, and major technical developments in mining will be necessary before any of the gold can be categorized as a code-compliant resource or reserve. To win this prize, the mining industry will have to rethink its approach to mining, both in old mining leases and in the unexploited ground. It will also have to find effective means of preventing gold theft and informal mining, which are on the rise.

Apr 5, 2023

By J. E. Davidsen, M. Honstad

"A well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. A worn or short tap-hole channel can lead to more violent flow, significantly increasing the fume emissions during tapping and leading to more metal being mixed with and lost to the slag. Over time, a worn tapping channel might cause side channels and damage to the lining around the tap-hole area. This can result in a burn-through which is a considerable safety risk and will cause significant production losses. At Eramet Norway Porsgrunn, tap-hole maintenance has been done regularly with electrode paste for over three decades with good results. This article summarizes some of the experiences obtained from this practice on a 33 MW SiMn furnace, as well as a change to a coal tar pitch-free binder. IntroductionA well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. Metal and slag are regularly tapped from the furnace and may cause a lot of wear on the tapping channel, increasing the risk of lining damage and ultimately leading to a burn-through. On furnace 10 at Eramet Norway Porsgrunn, the tap-hole area is the part of the lining that has been by far the most prone to burn-through since the startup of the furnace.Experience shows that almost all lining problems have started with burn-through in the tap-hole area or in close proximity to the tap-hole. During tap-hole repairs, side channels with metal and slag have also been observed emanating from the main tapping channel. In addition, a shorter tapping channel will cause more violent flow. This can lead to more metal droplets being entrained in the slag, and increase the risk of the furnace not being closed properly at the end of the tap.As a burn-through is a considerable safety risk, and also causes significant production losses, systematic work has been performed over the years to maintain the tapping channel in order to prevent burn-through."

Jun 1, 2019

By D. S. van Vuuren

Titanium bearing resources can selectively be chlorinated at temperatures below 200°C if the Ti02 in the feed is nitrided before chlorination. However, the nitriding reaction is highly endothermic, requires highly reducing conditions, is only thermodynamically favourable at elevated temperatures, and is affected by mass and heat transfer restrictions. At the required processing conditions, problems might also be experienced with sintering and with melting of slag forming components in the raw materials. A test programme was undertaken to study the effects of raw material type, temperature, gas composition, bed depth, carbon to raw material ratio and residence time in order to simulate conditions required for scaling up a nitriding process. In contrast to previous experience with low-grade titanium-bearing slag containing about 30% Ti02, ilmenite and chlorinateable slag do not form melting phases under the studied nitriding conditions and hardly sintered at all. Both feed materials can readily be nitrided with conversions in excess of 90% at temperatures around 1300°C and using bituminous coal as reducing agent with fixed carbon in excess of 1.1 times the stoichiometric requirement. The conversion decreases as the bed depth of the feed material increases and the N2/CO ratio in the gas decreases. Analysis of the relative rates of mass and heat transfer into the reacting beds of ilmenite and slag showed that the heat transfer rates are more limiting than the mass transfer rates. In order to increase the throughput that can be achieved in a kiln, it would be necessary to take special measures to enhance the heat transfer rates into the mass of reacting material. One such a measure is to pre-form the mass of reacting material into thin-walled, hollow brick shapes prior to introducing it into a kiln. Depending on bed depth, temperature and N2/CO ratio, required residence times in the high temperature zone of the kiln can vary between about 6 and 10 hours. Keywords Titanium dioxide, titanium nitride, carbo-thermic, reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011