Search Documents

By R. Van Rijswick

Crankshaft driven piston and piston diaphragm pumps inherently generate a varying flow each crankshaft revolution. Depending on the system connected, this flow variation results in a pressure pulsation. This pressure pulsation may, depending on the structural design, result in structural vibrations. In order to limit the level of pressure pulsations, volume absorbing devices, mostly gas filled vessels, are used. The standard selection of these so-called dampeners is based on the flow variation of the pump but does not incorporate the interaction with the connected system. The paper discusses the application of a pulsation analysis tool developed by WEIR Minerals Netherlands, manufacturer of GEHO positive displacement slurry pumps. The paper first discusses the basics of pressure pulsation analysis, such as flow variation generated by crankshaft driven pumps, and hydraulic effects such as capacitance, inductance and resistance and their influence on the hydraulic response of a system. Furthermore, the relation between pressure pulsations and structural vibrations, known as fluid structure interaction, will be discussed. Additionally, the capabilities of the pump pulsation analysis tool are presented, illustrated by examples of simulation results and experimental verification.

Jan 1, 2007

By H. J. Swanepoel, N. B. Strydom

Groups of up to twelve new recruits to the industry were subjected to climatic room acclimatization for either five, seven, eight or nine days prior to being tested for the degree to which they had been acclimatized. These tests were done at 32,2 0C (wet bulb) at a wind velocity of about 0,4 m/sec and the men worked for four hours at a rate of 215,6 kg m/min on one day and at a rate of 431,2 kg m/min on the second day. The results indicated that there is no significant difference between the degrees of acclimatization obtained by the eight- and nineday procedures which confirms the conculsions drawn in a previous report1. The eight-day procedure can thus be claimed to be perfectly adequate and safe. Decreasing the period of exposure to five or seven days would however, not be justified because of the significant differences in physiological responses that were observed on both test days between men acclimatized for these periods and those acclimatized for nine days. It is concluded that it would be unsafe to employ these shorter periods of acclimatization when underground environmental temperatures at which the men are to work, exceed 31 0C (wet bulb).

By P. A. Corbeil, C. Swart, F. Miller, V. Falmagne

Automation technologies are increasingly adopted in different mines worldwide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHD’s at Noranda’s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHD’s and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda’s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Sep 1, 2001

By C. Musingwini, M. Woodhall

An often overlooked factor in the analysis of mine layouts and schedules is technical operating flexibility, mainly due to its nebulous nature. If one glosses over technical operating flexibility the resultant mine layouts and schedules tend to be sub-optimal. The need to incorporate technical operating flexibility into the analysis and comparison of mine layouts and schedules is increasing in importance. This paper illustrates the nature of technical operating flexibility, reviews previous work on valuing operating flexibility and proposes how technical operating flexibility can be quantified for tabular reef mines by using a platinum reef deposit as a case study. Once technical operating flexibility is quantified it becomes possible to explore its incorporation into the analysis of mine layouts and schedules and subsequent optimization processes. The work described in this paper is part of a current PhD study at the University of the Witwatersrand. Keywords: mine plans, layouts, schedules, technical operating flexibility, ore availability.

By E. A. Brinkmann

A kinetic model framework for single particle kinetics in combined diffusion and adsorption processes is presented. The framework applies to the general case in which both diffusion and the adsorption reaction play important roles in determining the overall rate in processes where the migrating species can both adsorb and accumulate. The technique, which should be applicable to a wide range of reaction mechanisms, consists of an iterative integration procedure for the coupled diffusion and reaction equations. The case of a reversible linear adsorption reaction rate is developed. In order to verify the technique as a legitimate method of model development, an analytical solution for the identical case is derived and compared to the numerical solution. Excellent agreement exists between the two solutions.

Jan 1, 1987

By M. M. Oosterveld

Diamonds are mined from ancient raised beach deposits in southern Namibia where complex geological controls have resulted in patchy diamond distribution, largely related to irregularities (trapsites) in the bedrock. The distribution of the number of diamonds per sample is a discrete, reverse- J shape distribution which can be characterized by two parameters. These parameters have been transformed into a Beta and Theta Contribution which can be interpreted as reflecting the 'quantity' and 'quality' of the trapsites. The relationship of statistical parameters, obtained during the sampling of an ore deposit, to the geology of the deposit is an important element of ore reserve estimation. The large-scale regional trends in the contributions have been explained in terms of the geology.

Jan 1, 1987

The refractoriness of the gold in many of the pyritic ores from the eastern Transvaal is due mainly to the association between the gold and the sulphides, but it can be due to the presence of graphltlc carbonaceous material, which complicates the recovery of the gold by virtue of its adsorption activity. In an examination of the roasting characteristics of three flotation concentrates from the Barberton area, It was found that the gold in the concentrates occurred mostly in two forms: in very fine gold particles distributed within the arsenopyrite, and in a slightly coarser form loosely associated with the pyrite. Direct cyanidation of the concentrates gave gold extractions of from 16 to 30 per cent. After the concentrates had been roasted at temperatures of 650 to 700°C for 20 minutes with rabbling, the extractions varied from 86 to over 90 per cent. Examination of the residues after cyanidation indicated that gold was present in the porous calcines or in the calcined sulphide product. This observation, together with porosity measurements, suggests that physical encapsulation of the gold particles is the main reason for the refractory behaviour of the gold in the calcines.

Jan 1, 1988

By H. Jeram

The ilmenite, rutile and zircon processes of the mineral separation plant generate tailing streams, which still contain valuable mineral. This is due to a combination of factors, which include separator equipment efficiency, particle size effects and inefficient operating practices (equipment overloading, blockage, etc.). Recent developments by metallurgical equipment suppliers have led to increased mineral separator performance enabling recovery of previously lost valuable mineral. Mineralogical studies were conducted using QEM*SEM and MLA techniques to identify and quantify gangue mineral species and determine mineral association. Laboratory and pilot-scale test work was then conducted to develop suitable process flowsheets for the recovery of ilmenite, rutile and zircon from current and stockpiled tailings.

Jan 1, 2007

By D. J. Hallbom

A new graphical method termed the ?Design Curve Diagram? (DCD) has been developed to analyse non-Newtonian pipe flow data by relating the plastic Karman number to the plastic Reynolds number. Since the plastic Karman number is directly proportional to the pressure loss gradient and the plastic Reynolds number is directly proportional to the velocity, the DCD is essentially a non-dimensional pipe flow curve. This makes the DCD conceptually easier than the commonly used Hedström-Moody diagram. While, the DCD was developed for the analysis of yield plastic fluids (e.g., Bingham plastics), it is equally applicable to Newtonian fluids.

Jan 1, 2007

By R. Sun, R. G. Gillies, R. S. Sanders, J. Schaan

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is abetter indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By O. Bazhko

Regular analysis of different streams is important for the control of hydrometallurgical processes. Various physical and physical-chemical methods are applied for this purpose. Many modern methods require costly equipment and are subject to interferences. Therefore, redoxtitration methods remain of interest. The use of different types of oxidizing and reducing agents as well as redox indicators enables many cations and anions to be rapidly and accurately analysed. Sometimes redox titrations require the prior preparation and addition of masking agents. Selective, sensitive and low-cost methods of redoxtitration of copper and SO2 in plant conditions are described.

Jan 1, 2009

By P. J. D. Lloyd

An account is given of the development of a process to concentrate gold and other valuable minerals and to produce a discardable waste. In this process, the ore is coarsely milled, a bulk flotation concentrate is prepared, and the flotation tailing is scavenged in a hydrocyclone, which returns coarse gangue, moderately coarse valuable minerals, and locked valuable minerals back to the mill. The engineering developments required by this circuit in order that it will fit underground, and the progress made towards the achievement of those requirements, are reviewed. If the waste is to be suitable for use as a backfill in a deep-level, flat tabular excavation, it should be capable of being placed hydraulically, and should have both low voidage and high rates of drainage. Such a material could be prepared by the fine screening of the overflow from the cyclone in the proposed circuit. Possible methods for the handling of the concentrate and the recovery of its valuable constituents are described. The paper concludes with a discussion of the possible benefits from the use, in deep-level Witwatersrand mines, of a system involving concentration underground, extensive backfilling using the tailings from the concentration process, and hydraulic hoisting of the concentrate.

Jan 1, 1979

By R. Falcon, A. J. Ham

This paper summarizes the characteristics of Southern African coals, presents a fundamental approach to the combustion performance of coal, and reviews some of the recent developments in the fields of technological evaluation and boiler design for coals typical of this region. This includes a summary of the petrographic constituents of coa~ highlighting the differences between the Palaeozoic coals of the northern and southern hemispheres (Laurasia and Gondwana respectively), and the effects of these properties on the combustion performance of coal as seen in terms of laboratory, pilot-scale, and full-scale operating conditions. Recent developments in boiler design linked to advanced characterization studies and commercial experience have led to unprecedented use, with maximum effect, of the low-grade, high-ash, high-inertinite coals typical of some parts of this region. In the light of this success, more adequate understanding and better methods of assessment of the coals typical of the Gondwana region are called for, particularly in the light of the price premium for high-grade coal and the more cost-effective lower grade coals on the international steam markets.

Jan 1, 1988

By D. Harbottle, D. Rhodes, T. F. Jones, S. R. Biggs

Multiphase process design and optimization often depends upon the rheological properties of sludges and slurries. In practice the task of determining these important properties is usually carried out by removing small samples from a process line or process unit and performing tests with proprietary bench-top analysers near to site or at a remote laboratory. Sampling will remain an important procedure in industrial processes, but there is also a strong case for augmenting the routine information obtained using an in situ sensor, as suggested below. ?Sampling protocols can result in extensive turnaround periods from sample collection to the generation of results. The delay can have an effect on a variety of factors such as product quality, process operability and efficiency. ?Sampling of toxic or radioactive material can prove an even greater challenge to minimize human involvement. ?Removal often changes the rheology of a specimen, and might lead to incorrect conclusions being drawn about the condition of a sludge. ?Sludge and slurry in a containment suffers a gravitational gradient, so that a removed sample should be paired with its location, particularly in the vertical dimension.

Jan 1, 2007

By P. J. van Staden, T. W. Walker

The Minfurn is a novel carbon-regeneration furnace developed at Mintek. It combines the advantages of direct resistive heating in a vertical-tube furnace with those of continuous operation, in a furnace whose capital, operating, and maintenance costs compare favourably with those of conventional rotary kilns. After successful tests under experimental conditions on carbons containing different contaminants, a 3 kg/h unit was installed on the carbon-in-pulp (CIP) plant at the Klipwal Gold Mine near Piet Retief, where it has been operating at, on average, 123 per cent of its design capacity. Since the installation of the Minfurn, monthly average losses of dissolved gold of less than 0,02 p.p.m. have been maintained for several successive months for the first time since January 1989. It is also possible that the monthly average residue values have been reduced. Further improvements to the carbon circuit are possible, and the possibility of making further savings by a reduction in the carbon-throughput rate still needs to be investigated. The mathematical modeling of the furnace has progressed to the stage where the future scale-up and design of the Minfurn can be carried out by simulation of the performance of different designs, and choosing the design that yields the desired performance.

Jan 1, 1993

By M. J. Nicol, P. D. Scott

The kinetics of the non-oxidative dissolution in acids ofthe iron sulphides FeS, Fe-FeS, and Fe9S10 were studied by the use of rotating-disc electrodes of the various compounds. It was found that the rates of dissolution vary by orders of magnitude with changes in surface potential. The dissolution rates depend on non-integral orders of hydrogen-ion concentration, which in turn vary with potential. A mechanism based on the following premises is proposed to explain the kinetics of dissolution of the iron sulphides. (I) Only an FeS compound that is exactly stoichiometric dissolves in accordance with the accepted theory of ionic charge transfer. (2) Any non-stoichiometric iron-deficient iron sulphides must be reduced to exactly stoichiometric FeS before spontaneous non-oxidative dissolution can occur. The dissolution of Fe.S1o and slightly iron-deficient FeS compounds under open-circuit conditions occurs only when an oxidation reaction (usually the oxidation of hydrogen sulphide to elemental sulphur) can provide the electrons necessary for the production of exactly stoichiometric FeS. The establishment of such a mixed-potential system is the reason for the induction period that occurs during the dissolution of pyrrhotites in acids.

Jan 1, 1979

By P. G. Van Der Walt

This paper deals with the reticulation of deslimed tailings from surface to the stope face underground. Reference is made to the experience gained at the pilot plants operating on four of the gold mines administered by Gold Fields of South Africa, as well as at the full-scale system at East Driefontein which was commissioned recently. Mine-wide backfill systems are currently being installed on five other mines administered by Gold Fields. These six full-scale systems are capable of handling more than 270 000 tons of backfill solids per month. The type of reticulation system chosen, the selection of flowrates and the composition of the slurry, as well as the selection of the appropriate pipes and ancillary equipment are discussed. Both theoretical and practical aspects are taken into consideration. Other aspects covered include the design of underground storage dams and communication systems.

Jan 1, 1988

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By M. Bryson, V. Deeplaul

As a national facility, Mintek?s brief is to conduct high calibre research that allows the most effective utilization of South African resources. The research takes two different forms, with the efforts being directed at both high-risk endeavours that may lead to the development or adoption of new technologies or the reapplication of technologies to potential new operations. Starting in the 80s Mintek began developing a process to upgrade the UG2 ore and invested heavily in projects, equipment and people to service the industry. Some of the highlights of that work that has been conducted here include: ?Development of a milling and flotation process for UG2 ores ?Development of the ?Mintek Process? for maximizing PGM recovery for UG2 ores ?Conversion of the UG2 milling circuits to open circuit ?Development of a robust pilot plant facility for use in plant design studies ?Use of dense media as a waste rejection option ?Use of attritioners in flotation circuits. More recently, and with the future in mind, the following processes are being researched, some of which have already been commercially applied: ?Development of a flowsheet for Platreef ores ?Use of optical sorting technology for upgrading platinum ores ?Use of a mini-plant for reagent optimization studies. Each of the highlights listed above will be discussed in the paper.

Jan 1, 2004

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.