Search Documents

By W. Bleloch

Published in the Journal, September 1970, and presented at a colloquium on 'Future of the Steel Industry', 17th March, 1971. Errata (a) The final sentence in the penultimate paragraph, left hand column p. 34 of the text should read: 'In the hot regions of the bosh and stack the C+CO2=2CO reaction proceeds to CO from coke carbon and carbon dioxide generated by reduction of iron oxides by CO (the so-called solution loss of carbon)'. The italicised words have been omitted in the text. (b) Temperature in Fig. 3 is K not C. (c) In Fig. 9, connection from top plate of column 10 to heat exchanger 9 has been omitted. DISCUSSION J. B. BEEDON AND C. J. JONKER* Dr Bleloch's paper has outlined the advantages of recycling stack-gas of low nitrogen content in the blast furnace. In the first instance it would appear to be extremely beneficial in controlling the hearth temperature and allowing a 100 per cent oxygen-blast to be used. On a second point however we have to disagree. It is claimed that heat is liberated in the combustion zones by the oxidation of CO to CO2 near the tuyeres and in the subsequent reduction of the CO2 by CO. The author has hypothesized as follows, and we quote: 'The C+CO2=2 CO reaction in the outer combustion zone at about 1 700°C is no longer endothermic due to loss of stability of CO2 and its consequent dissociation into CO and free oxygen.' This statement requires closer examination. If we consider the individual events occurring with the CO in the recycled topgas, with the oxygen in the blast and with the coke in the burden, as done by Dr Bleloch, the following heat considerations emerge. All heats of reaction are calculated from the enthalpy values of each reactant and product, as well as the temperature dependence of their molar heat capacities. (a) At the tuyeres: CO+1/2 O2-+CO2 . . . . . (1) CO, CO2 at 500°C; O2 at 25°C. ?H reaction = -65 000 cals/mole CO The reaction (1) is exothermic. (b) In the outer combustion zone: CO2+C?2 CO . . . . . . . . (2) C, CO at 1 700°C; CO2 at 500 0C. ?H reaction = -56 000 cals/mole CO Reaction (2) is endothermic. The overall heat gain of reactions (1) and (2) is ?H=+56 000 - 65 000= -9000 cals/mole CO i.e. the overall reaction is slightly exothermic, the amount of heat liberated is however smaller than suggested by Dr Bleloch. (c) The dissociation CO2+CO+1/2 O2 . . . . . (3) is a highly endothermic reaction at 1 700 0C, requiring 82 000 cals/mole CO2 to proceed to completion. Furthermore, this reaction (3) is energetically not favoured to proceed, as can be observed from the free energy-temperature relationship of figure (3), which favours the formation of CO2 at 1 700 0C. Hence direct dissociation of CO2 at 1 700 0C appears to be unlikely.* The concept of recycling topgas is however still intriguing from many other points of view. Apart from providing a very efficient method of hearth temperature control, it will create a much higher CO partial pressure in the stack. Whether the rate of indirect reduction in the stack will be proportional to this partial pressure or not is un-

Jan 9, 1970

By G. Akdogan, C. Bergmann, C. J. Coetzee, Q. G. Reynolds, S. J. Baumgartner

Submerged arc furnaces (SAF) are used extensively in the production of ferrochrome, where charge material – consisting of mixtures of carbonaceous reductants, fluxes such as silica, and ore in the form of pellets – is fed through chutes into the vessel. The feed typically forms a thick bed or ‘burden’ of solid particulates above a bath of molten material below. This burden layer surrounds three electrodes, which are typically arranged in a triangular configuration in circular SAFs. A major challenge in the industry is the availability of sought-after reductants, volatile market conditions, and increasing electricity tariffs in South Africa. A good understanding of the physical properties of the raw materials in the charge is therefore of great value in order to best deal with the reductants available at any given time, and thereby maximising furnace throughput. This paper presents a study of the effects of different particle properties on particle flow behaviour relevant to SAF operations. Discrete element model (DEM) simulations were used to estimate the sensitivity of the particulate flow of beds of charge material to properties such as the coefficients of friction, particle shape and size, and others. The present study lays the groundwork for the development of full DEM models of the SAF that will greatly improve understanding of the flow of complex mixtures of solid particles in the submerged arc furnace, and how the relative physical properties of each component in the charge can influence electrical behaviour of the burden.

Sep 1, 2021

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publication Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis. Index, only if paper is long and involved. Introduction, including a brief statement of conclusion. Development of the main substance. Conclusions, in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systemé International d'Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organisations as well as to the Institute.

By J A. H Campbell

AK6 is a Cretaceous aged kimberlite located in the north-east of Botswana, close to Debswana's Drapa and Letlhakane Mines. It was discovered by Debswana in 1969, but was considered unattractive from an economic perspective. In 2003, Debot Prospecting Pty Ltd ('Debot') re-assessed the area and with the advent of new prospecting technology, particularly large diameter drilling ('LDD') and more detailed ground geophysical surveys found AK6 to be of interest. In 2005, the Boteti joint venture was formed between Debot and African Diamonds plc ('AFD'), which covered a number of Prospecting Licenses, including that which contained AK6.

Jan 1, 2010

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis, including a brief statement of conclusions. Index, only if paper is long and involved. Introduction. Development of the main substance. Conclusions, in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors &, Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler. H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory \matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol %is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d'Unites (S.L) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramms metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, n, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and there. fore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .' . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there IS full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute.

By S. Soren, K. Deo Mehta, G. Jha

The paper aims to find a sustainable sintering process through cleaner means, in order to achieve the desired outputs with zero environmental impact. At present, sintering has no control over its environmental impacts. These impacts occur when fossil fuels such as coal and coke are used in metallurgical sintering. These fossil fuels are undoubtedly effective in their assigned reducing task, but simultaneously emit about 220 kg of GHGs (greenhouse gases) per tonne of sinter produced. The current attempt has focused on reducing these emission levels by switching from coke to a renewable fuel source such as biomass. Biomass is a cleaner fuel source with a significantly lower emission footprint compared to coke. In the experimental campaign, sawdust and wood-charcoal were used in substitution for coke. Experiments were designed in a progressing substitution to obtain the maximum substitution ability without compromising the sinter properties. Sawdust as raw biomass source optimally substituted 10% of coke. The substitution levels were remarkably higher (30%) for wood charcoal due to its low moisture and high calorific values. A fuel blend with 30% biomass and remaining coke succeeded in producing a sinter with acceptable quality indices. Sinters prepared with or without biomass contribution shared an identical phase transformation and microstructures. In order to to maintain consistency in the process, every effort was made to maintain all operational and process parameters identically, except for the fuelling framework. Keywords: Sintering, sustainable, biomass, GHGs, fuel substitution

Jan 1, 2020

By E. J. Walls, W. C. Joughin

"In selecting a suitable method to sink a vertical shaft for underground access, a number of constraints influence the ultimate decision of where and how to develop the shaft, not least among these being safety, development and construction time, and cost. Two additional considerations stand out: these being geotechnical conditions and technology, the latter taking into account existing underground access. Assuming a project for which an existing underground excavation is available, it is tempting to build a shaft sinking project from the outset based on the raiseboring method, which has the potential to be the safest, fastest, and least expensive method provided that geotechnical conditions permit.And therein lies the rub: regardless of project time or cost constraints, when it comes to raiseboring a long (say, greater than 500 m), large diameter (greater than 4.5 m) shaft, the rock mass conditions ultimately dictate what method of shaft sinking will be feasible. Over the course of several studies for a particular project, several geotechnical analyses were carried out specifically for the purpose of developing a shaft by raiseboring. Risk analysis and experience showed that where the rock mass conditions indicated an unacceptably high risk potential, an alternative method needed to be considered, even if this meant increasing both the time and financial requirements.In this paper we present an overview of geotechnical investigation practices for shaft sinking. Decisionmaking thresholds for raiseboring or other methods of shaft sinking are discussed, including probabilities of failure, empirical rock mass classification, basic wedge failure, and back-analysis of a failed case. The design of appropriate support, and analysis of relative safety benefits for various shaft sinking methods, falls outside the scope of this work, and will be presented in a separate paper.IntroductionThe potential for rock mass failure during shaft development and construction affects whether a project is completed safely, on time and on budget. During the course of several studies to establish ventilation shafts for an underground expansion project, geotechnical analyses of rock mass stability and failure potential were carried out. The investigations were guided by the method of McCracken and Stacey (1989) together with insights from Peck and associates (Peck, 2000; Peck and Lee, 2007, 2008; Peck, Coombes, and Lee, 2011)."

Apr 1, 2019

By E. Rex, T. J. Goff, W. S. B. van Beek, P. E. Nel

"The PGM smelting industry is known for operating at significant high superheats. Both the slag and matte phases that separate via gravity need to be tapped out of the furnace in a safe and efficient manner, which can be achieved only through sound tap-hole management practices. This paper gives an overview of the tap-hole management approach followed in the operations at Lonmin’s Western Platinum Smelter.Five circular AC furnaces are operated, with each furnace comprising essentially a crucible and auxiliary equipment. Within the crucible, slag and matte tap-holes are situated at different elevations. The slag phase is tapped at a higher elevation than the matte phase. At the three older furnaces, tapping is done by the conventional method of lancing open the tap-hole and closing it with a dolly. However, at the two newer furnaces, tap-holes are opened and closed with the aid of a drill and mudgun.Tap-hole management can be divided in a number of aspects. In order to achieve a safe opening and closure every time, Lonmin distinguishes between three important aspects - the design of the tap-hole system, the operating practices followed, as well as care and maintenance. This paper briefly describes the tapping channel and cooling requirements for handling superheated matte, together with the difference in design of the matte and slag tap-holes. Mention is also made of the importance of auxiliary equipment, which includes the launders, fume extraction, granulation water, and mudgun and drill units. Improvements made to the matte tapblock design are discussed.The monitoring, alarm, and safety systems related to matte and slag tapping are described. Tap-hole life and different wear mechanisms are mentioned. Tapping can be done safely only if the tap-holes and equipment are maintained properly. Mention is made of the tap-hole refractory repair practices, and the improvements made in order to reduce repair time as well as to extend the time between deep repairs. The importance of the correct tap-hole clay selection in order to nurse the tapping channel after each tap is also discussed.The paper finally touches on some research and development work that was done in order to improve the monitoring of the condition of the tapblock by means of fibre optic temperature sensors"

Jan 1, 2014

By Lesley Andrews

"Electron microbeam analysis of metallurgical samples covers a broad field and has applications in the areas of minerals processing, hydrometallurgy, pyrometallurgy, physical metallurgy and corrosion.Some idea of the possibilities of microbeam techniques can be illustrated by examining the following example of a run of mine gold ore sample. Milling and bulk chemical analysis of the ore will provide major and minor element analysis as well as the gold grade. More detailed chemistlY can also reveal the presence of trace elements that may be advantageous or deleterious to downstream processing. Electron microbeam analysis can provide additional information in the form of - size, liberation, association and composition of the gold, the percentage of refractory gold, the size, liberation, association and composition of enclosing sulphide or arsenide phases and the levels and association of the trace elements that may affect processing. In most cases electron microbeam analysis compliments bulk chemistry, and does not replace it. Both techniques should be used in parallel for maximum effect.This paper touches on the origin and history of electron microbeam techniques, as well as the theory behind microbeam analysis and processing. The more common types of instruments and their applications will also be dealt with briefly - more details on, and examples of, the applications and choice of technique will be covered in the presentation.Mosely first discovered, in 1913, that the frequency of emitted X-radiation excited by an electron beam is a function of the atomic number of the analysed element. This discovery led to the development of spectrochemical analysis. The forerunners of the electron microanalysers of today, however, were only invented during the nineteen fifties. The electron microprobe was developed in parallel by Castaing and Guinier in France and by Borovski in Russia, but Castaing's design was the basis of modern microanalysers. The initial area of analysis was brought down from over 1 mm2 to less than 2 µm, as it is today. In 1956 Cosslett and Duncumb invented the scanning electron microprobe, where a beam of electrons could be scanned across an area of a sample. This, in turn, led to the development of the electron microprobe with both scanning and point analysis capabilities that we know today.Essentially, all electron microbeam instruments operate by the production of a beam of electrons from a filament in a vacuum (i.e. an electron gun). The electron beam leaves the gun and is accelerated and focused by a series of electromagnetic lenses while passing down an evacuated column. The electrons eventually strike the surface of the sample to be analysed and may travel through a thin sample (transmitted electron microscopy) or react with a thicker sample to produce several reflected kinds of radiation."

Jan 1, 2014

By P. R. Jochens

SYNOPSIS This review article first highlights the past performance of the industry and discusses the manner in which the development of the industry has followed a logical progression from mining to the production of mineral and metal products of specification purity. Then the numerous constraints against a greater contribution by the industry are enumerated. Attention is drawn to the extent of further processing that can be undertaken in the context of mining and metallurgical processing, not only to indicate the benefits that can be derived from the added-value conferred on a mineral or metal commodity during each stage of its further processing, but also to point out some important corollaries of further processing. The many opportunities and challenges for an increased contribution by the minerals and metals industry are then reviewed. This major section includes a list of commodities for which increased penetration of export markets could be sought because the increasing resistance level (a term developed in this paper) has not been attained; a list of commodities that are imported at present, many of which could be produced locally on the basis of identified resources and expertise; a list of commodities for which additional uses should be developed so that South Africa, which possesses the largest reserves and is the largest exporter, can increase its production rate; and examples of commodities for which further processing is still at an early stag*..

Jan 1, 1985

By A. G. Royle

The reasons for constructing a model of an orebody for which both the parent population and the sampling distribution are known are discussed and details of the model are given. A brief summary of Matheron's theory of regionalized variables is included, with particular reference to his kriging estimators and their variances. Using the model, a comparison is then made between these kriging estimators and other commonly-used estimators. These are compared to find the one with the minimum variance, and an analysis is included to investigate whether any of the estimators is biased. Also included is a comparison between theoretical and experimental variances for some of the estimators.

Jan 1, 2014

By R. Weideman, K. du Preez

Biological sulfate reduction has become a successful treatment alternative for acid mine drainage and Mintek is developing biological processes for treatment of highsulfate mine waters. Treatment of these high-sulfate waters is achieved by sulfatereducing bacteria that reduce sulfate to produce sulfide as a product, in the form of H2S and HS− at neutral pH. This introduces the opportunity to apply treated effluents from biological treatment processes for the recovery of metals, such as copper, from metallurgical waste streams. This study models the kinetics of copper sulfide precipitation from a complex bioleach liquor. The results indicated a rapid rate of reaction and the formation of covellite, suggesting the potential to use biogenic sulfide to recover copper as a metal sulfide product.

Jan 1, 2023

By G. Sahasrabudh, G. DeIulii, K. P. Galvin

A novel agglomeration process has been developed, utilising a concentrated water in oil emulsion as a binder. The binder is typically 95 wt% water, the remainder being an organic phase containing kerosene and the emulsifier— sorbitan mono oleate (SMO) in equal mass portions. The binder can selectively agglomerate hydrophobic particles in less than 7 seconds. The agglomeration has proven to be highly effective in recovering any particle of virtually any size, provided the particle is hydrophobic. The approach has previously been applied to coal, magnetite and silica. In the paper, sodium isobutyl xanthate (SIBX) and its much longer chain version, potassium tetradecyl xanthate (C14X), were used separately as collectors to selectively agglomerate chalcopyrite from the ore. Xanthates attach to metal sulphides, thus hydrophobising sulphide mineral particles. Chalcopyrite is a sulphide mineral; however, it hydrolyses quickly in the presence of water. Ethylenediaminetetraacetic acid (EDTA) was used to remove the oxide layer formed at the surface of the mineral particles after wet grinding, leaving behind a freshly generated metal sulphide surface. After the EDTA treatment, the ore particles were quickly conditioned at an optimised pH as well as collector concentration and agglomerated. The agglomeration achieved a copper recovery of 75% within 7 seconds, consistent with the recovery achieved by flotation over much longer time scales. Keywords: Chalcopyrite, agglomeration, froth flotation, interfacial chemistry, X-ray fluorescence, selective hydrophobisation

Jan 1, 2020

By N. Morris

In South Africa, diamonds are mined predominantly in rural areas. Kimberlitic diamonds dominate in Limpopo and the Northern Cape Provinces whereas alluvial diamonds are mainly sourced from the North West and Northern Cape Provinces. There are a few large and medium sized diamond companies (De Beers, Petra Diamonds, Trans Hex, Rockwell and Alexkor). There are many smaller companies involved in diamond mining, mostly alluvial diamond mines. The nature of alluvial diamond deposits is that they are aerially more extensive and thus their surface impacts are more pervasive: The recent downturn in diamond prices has resulted in the sudden cessation of mining at many small and medium diamond operations. The South African Mining Charter requires all mines, including diamond mines, to subscribe' to .the following empowerment objectives:

Jan 1, 2010

By T. G. Pedro, Q. Gonzalo, R. E. Roberto

Anionic surfactants, such as oleic acid and sodium oleate (OLE), and cationic surfactants, such as dodecyl amine-hydrochloride (DDA), are used as flotation collectors of spodumene. However, recovery is poor even if activating ions are used because gangue minerals are also activated. Some reports demonstrate that OLE/DDA mixtures act as a selective collector to enhance spodumene recovery. From mostly macroscopic tests, it has been argued that anionic OLE and cationic DDA form electroneutral complexes, which are adsorbed on the mineral surface through chemisorption; however, no molecular evidence has been presented. Therefore, the adsorption mechanisms of the collector mixtures remain mostly unknown. It seems necessary to first study the behaviour of these surfactants confined in salt solutions, to determine auto-associations when they are pure and cross-associations when mixed, the transition from monomers to micelles, and the structure of the micelles and the effects of pH, temperature and concentration. In this paper, ab initio calculations are first used to determine the surface charge distribution of OLE and DDA separately. Then molecular dynamics simulations are used to determine the conformation, aggregation, and diffusion of these pure and mixed surfactants in freshwater and saltwater with the ionic strength of seawater in a pH range. In particular, it is interesting to determine the various associations that result in mixtures of both surfactants and the impact of alkali and alkaline earth metal cations on the structures formedp. Cations influence the order of the structure and orientation of water dipoles, reducing the mobility of water, ions, and surfactant molecules. This knowledge is critical to improve the molecular understanding of the adsorption mechanisms on minerals. Keywords: Computer simulation, molecular dynamics, flotation, collectors, saltwater

Jan 1, 2020

By V. E. Cogho

Optimum Coal Mine comprises numerous defunct, active, and future mining sections. The mine is primarily a large opencast coal mine; however, underground mining activities will be increasing steadily over the next five years. Opencast and underground mining activities have a significant impact on surface and groundwater resources. To ensure that the mine will be able to continue with its mining operations in the catchment, the extent of this impact requires that substantial intervention and mitigation measures need to be implemented to ensure the environmental integrity and economic use of the catchment's water resources. In developing a sustainable long-term mine water management strategy, numerous scenarios had to be analysed. The various scenarios are a combination of water and land management activities. The main components of the mine's integrated water management strategy include: ? Management of water recharge by continual and appropriate rehabilitation of disturbed land ? Beneficial re-use of impacted mine water for coal plant process water and mining operations ? Reclamation and desalination of remaining excess impacted mine water to potable standard. From the mine's long-term water balance, it is evident that the continued implementation of numerous water management actions is required to mitigate the water resources impact in a sustainable manner. In addition, the installation of a water reclamation plant at Optimum Coal Mine (15Ml/day) is a key step for the mine to achieve a zero impact target.

Jan 1, 2012

By A. Navarra, A. Quelopana

The mine production scheduling problem (MPSP) has been studied since the 1960s, and remains an active area of computational research. In extending the concepts of the MPSP, the automated mine may now be regarded as a hierarchical intelligent agent in which the bottom layer consists of distributed robotic equipment, while strategic functionality occupies the higher layers. Here we present a disambiguation of artificial intelligence, machine learning, computational optimization, and automation within the mining context. Specifically, the Q-learning algorithm has been adapted to generate the initial solutions for a high-performing strategic mine planning algorithm, originally developed by Lamghari, Dimitrakopoulos and Ferland, based on the variable neighbourhood descent (VND) metaheuristic. The hierarchical intelligent agent is presented as an integrative conceptual platform, defining the interaction between our new Q-learning adaptation and Lamghari’s VND, and potentially other hierarchically controlled components of an artificially intelligent mine, having various degrees of automation. Sample computations involving Q-learning and VND are presented.

Dec 1, 2021

By F. M. Ramadhan, M. R. Pratama

Monitoring open-pit mine road conditions has become very critical nowadays. There are several benefits to in conducting research on this field such as opportunity to improve truck’s speed which directly influences truck’s productivity. This research aims to provide a semi real-time, and sensors-based automatic road damage detector that predicts the road quality through road damage exact location tracing, road damages auto-classification, and real-time instruction in the form of work order format to mining road maintenance, and repair authorities through mobile apps and maintenance unit’s in-cabin display. It will also provide the maintenance/repair activity performance evaluation via integrated dashboards. The artificial neural network algorithm is applied during the process of data training regarding classifying road damages and severities which resulted in a valid model. The road damage classification model has a precision level of 80.5% in predicting whether the road is damaged or not. Using this approach, we are expecting to visualise a road quality map of all active roads on mine site.

Sep 1, 2021

By D. Skelton

The Renard kimberlite cluster is located in the Monts Otish region of Quebec, Canada. A Canadian National Instrument (NI) 43-101 compliant resource statement for the Renard kimberlites 2, 3, 4 and 9 and the Lynx kimberlite dyke was first issued in 2008 followed by a Preliminary Economic Assessment and the development of a conceptual mine plan. Following a successful drill program in 2009 that greatly expanded the amount of kimberlite in Renard 2, a revised resource statement was issued in December 2009 comprising 23 million carats of Indicated Mineral Resources and 13 million carats of Inferred Mineral Resources, a threefold increase on the previous estimate. The project is currently the focus of a second Preliminary Economic Assessment and it is expected that a full feasibility and permitting program will commence in 2010 leading to the creation of Quebec's first diamond mine by 2013.

Jan 1, 2010

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

Recycling has become an important part of the lithium-ion battery (LIB) life cycle due to the growing demand for energy storage in applications like electric vehicles and renewable energy. Recycling spent LIBs provides a secondary source for strategically scarce metals, like lithium and cobalt, helping to reduce the environmental impact of LIBs. Organic acids have been proven to be effective lixiviants with the benefit of reduced environmental impacts, amongst which citric acid has shown to exhibit similar extraction performance when compared to mineral acids. Leaching LCO and NMC batteries with 1.5M citric acid and 2 vol.% H2O2 at 95°C, 20 g/L for 20 minutes achieved 93% Al, 90% Co, 96% Li, 94% Mn and 94% Ni dissolution. The strong chelating property of citric acid affects the separation of the metals, providing unique extraction opportunities. The first extraction uses 12 vol.% D2EHPA at a pH of 2.5 and O/A ratio of 2 to separate 96.4% Mn and 100% Al from the PLS in two counter-current stages. Stripping the loaded organic with 1.25M citric acid at an A/O ratio of 3 allows for up to 91% stripping of the manganese in a single stage. The second extraction then separates 96.5% Li from the PLS in three counter-current stages using 20 vol.% D2EHPA at a pH 5.5 and O/A ratio of 5. The raffinate remaining after the second separation contains 48.4 wt.% Co and 50.3 wt.% Ni. Keywords: Hydrometallurgy, lithium-ion batteries, metal recycling, citric acid, solvent extraction

Jan 1, 2020