Search Documents

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

By M. J. Leeuwner

Computational fluid dynamic (CFD) modelling is used to research the complex flow structures that exist in a hydrocyclone. By simulation of a two phase (water and air) flow system, the internal flow and multiphase interactions are investigated. The suitability of CFD modelling as a design tool is further evaluated by examining the effect of varying device dimensions. Three hydrocyclone geometries, used in previous studies, are specified. A transient simulation approach, which employs the Reynolds Stress Model as turbulence model and the Volume of Fluid model as multiphase model, is followed. Results are validated qualitatively against experimental measurements from the previous studies. Keywords: CFD modelling, hydrocyclone, Reynolds stress model, multiphase flow

Jan 1, 2008

By W. Wittke, J. Gattermann

ABSTRACT: One alternative to close a radioactive waste repository in rock salt is the construction of a “Cross Section Closure (CSC)“ sealing barrier. The proposed material for the CSC is highly compacted bentonite. To investigate the swelling behaviour of a highly compacted bentonite a large number of laboratory tests were performed. In addition, large scale model test were carried out to demonstrate the development of a nearly homogeneous and isotropic swelling pressure. The results of the large scale model tests were interpreted numerically based on the models for stress-strain behaviour and water uptake which are implemented in the finite element codes FEST03 and HYDOPO. The investigations show a good agreement of the results of the model tests and the corresponding analyses and show, that the theoretical models are capable of describing the behaviour of sealing structures based on highly compacted bentonite. ZUSAMMENFASSUNG: Eine Möglichkeit für den Verschluß eines Endlagers für radioaktive Abfälle im Steinsalz ist die Konstruktion einer Querschnittsabdichtung aus hochverdichtetem Bentonit. Zur Untersuchung des Quellverhaltens von hochverdichtetem Bentonit wurden eine große Anzahl von Laborversuchen durchgeführt. Um die Entwicklung eines nahezu homogenen und isotropen Quelldrucks nachzuweisen, wurden darüber hinaus auch Modellversuche in größerem Maßstab durchgeführt. Die Ergebnisse dieser Modellversuche wurden im Hinblick auf die Wasseraufnahme und das Spannungs-Verformungsverhalten mit Hilfe numerischer Berechnungen mit den finite Element Programmen FEST 03 und HYDOPO interpretiert. Die Untersuchungen zeigen gute Übereinstimmungen zwischen Versuchs- und Berechnungsergebnissen. Die numerischen Modelle sind somit geeignet, das Verhalten von Abdichtungsbauwerken aus hochverdichtetem Bentonit zutreffend zu beschreiben. RÉSUMÉ: Une possibilité pour fermer un dépôt final de déchets radioactifs dans sel gemme est la construction d'un étanchement de coupe transversale, fabriqué de bentonite fortement compacté. Pour étudier le comportement de gonflement de bentonite fortement compacté, de nombreux essais en laboratoire ont été exécutés. En outre, des essais sur modèle sur une plus grande échelle ont aussi été exécutes afin de prouver le développement d'une pression de gonflement à peu près homogène et isotrope. Les résultats de ces essais sur modèle étaient interprétés en vue de l'absorption d'eau et du comportement contraintes-déformations par le moyen de calculs numériques avec les programmes d'éléments finis FEST03 et HYDOPO. Les études montrent de bonnes conformités entre des résultats d'essai et de calcul. Les modèles numériques sont ainsi capables de décrire justement le comportement d'ouvrages d'étanchement fabriqués de bentonite fortement compacté.

Jan 1, 2003

By P M. Bradbury

The nature of aggressive process chemical requirements typically in the Platinum Refinery Industries, lend themselves to the use of Polymer Composite Glass Reinforced plastics for pipework and other associated equipment in these types of Plants. This paper discusses the basic characteristics of a Polymer Composite glass reinforced piping system and gives sample examples of applications in current present day use.

Jan 1, 2006

By I. Hague

Support liners for underground applications include steel and timber sets, meshing and lacing, screen/mesh, shotcrete and thin support liners (superskins). Over the past few years, major advances have been made in the design and application of liners; especially shotcrete and thin support liners. For shotcrete in mines these advances include the common use of slick-lines to solve logistics problems, the design of alkali free accelerators, the use of synthetic fibres and the new generation application equipment. The field of thin support liners is a new one but advances have been dramatic. This paper discusses the progress made and the need for standardization in definitions and testing for thin support liners. It concludes that the newer technologies have a huge potential positive impact on the industries, from both safety and cost points of view. Le chemisage de soutènement pour extraction souterraine comprend des cadres d’acier ou de boisage, mailles et chapeau, cribles/mailles, béton projeté et des chemisages minces de soutènement (super-peaux). Dans les dernières années, des progrès considérables ont été fait dans la conception et application des chemisages, en particulier les chemisages de soutènement en béton projeté et les chemisages minces. Pour le béton projeté dans les mines, ces progrès comprennent l’utilisation courante de lignes de minerais broyés fin pour résoudre des problèmes de logistique, la création d’accélérateurs sans alcali, l’usage de fibres synthétiques et d’une nouvelle génération d’outillage. Le domaine des chemisages minces de soutènement est très récent mais les progrès ont été rapides. Cette étude présente les progrès accomplis et discute du besoin de standardisation dans les définitions et les tests pour chemisages minces de soutènement. La conclusion est que les technologies nouvelles présentent un énorme impact potentiel positif sur les industries, du point de vue à la fois de la sécurité et de la rentabilité. Unterstützungsverkleidungen für Untertaganwendungen inkludieren Flecht und Seilwerk, Gitter/Geflecht, Spritzbeton und dünne Unterstützungsverkleidungen (superskins). Während der letzten Jahre wurden grosse Fortschritte im Design und in der Anwendung der Verkleidungen gemacht; besonders bei Spritzbeton und dünnen Unterstützungsverkleidungen. In Bezug auf Spritzbeton in den Gruben schließen diese Fortschritte den allgemeinen Gebrauch von Rutschbahnen ein um Logistikprobleme zu lösen, das Design von alkalifreien Akzeleratoren, den Gebrauch von synthetischen Fasern und die neue Generation von Anwendungsausrüstung. Der Bereich der dünnen Unterstützungsverkleidungen ist neu, aber die Fortschritte sind drastisch gewesen. Diese Arbeit behandelt den erzielten Fortschritt, die Notwendigkeit der Normierung in den Definitionen und in der Prüfung dünner Unterstützungsverkleidungen. Sie kommt zum Schluß, daß die neueren Technologien, sowohl vom Gesichtspunkt der Sicherheit als auch der Kosten, eine sehr große potentielle positive Auswirkung auf die Industrien haben.

Jan 1, 2003

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

By P. Sun

Abstract: From the viewpoint of interaction mechanics of solid and gas, a coupled mathematical model is presented for coal/rock mass deformation and gas leak flow in parallel deformable coal seams. Numerical simulations for the prediction of the safety range of mining of protection layer are performed with experimental data from a mine with potential danger of coal/gas outbursts. Analyses show that the numerical simulation results are consistent with the measured data on the spot. Therefore, the coupled model shows a positive future for applications in a wide range. ZUSAMMENFASSUNG:Von der Veranschaulichung der Abhängigkeit Mechaniker für Körper und Gas, wird ein verbundenes mathematisches Modell für festen coal/rock Deformation und Gasleckstelle Fluß in parallele deformable Kohlenähte dargestellt. Numerische Simulationen für die Vorhersage der Sicherheit Strecke, die Schutzschichtbergbau verwendet, werden mit experimentellen Daten von einer Grube mit möglicher Gefahr der coal/gas Ausbrüche durchgeführt. Analysen zeigen, daß die numerischen Simulation Resultate mit den gemessenen Daten bezüglich des Punktes gleichbleibend sind. Folglich zeigt das verbundene Modell eine positive Zukunft für Anwendungen in einer breiten Strecke. RÉSUMÉ: Du point de vue de la mécanique d'interaction pour le solide et le gaz, un modèle mathématique couplé est présenté pour l'écoulement plein de déformation de coal/rock et de fuite de gaz dans les filons houillers deformable parallèles. Des simulations numériques pour la prévision de la gamme de sûreté employant l'exploitation de couche de protection sont effectuées avec des données expérimentales d'une mine avec le danger potentiel des accès de coal/gas. Les analyses prouvent que les résultats numériques de simulation sont conformés aux données mesurées sur place. Par conséquent, le modèle couplé montre un futur positif pour des applications dans un éventail.

Jan 1, 2003

By J. Riss, S. Gentier, A. Marache

The study of the hydromechanical behaviour of fractured rock masses requires a detailed knowledge of the isolated fractures. The aim of the paper is the simulation of the evolution of the void space, located between both walls of a fracture, during a shear test under constant normal stress. Results of the mechanical simulation model are first validated then analyzed in detail. We observe that, during the shear process, there is an opening of the fracture with the creation of preferential channels. These channels are determined at the early phase of the shear process (pre-peak phase), and we observe during the post-peak phase that void areas increase in size rather than the creation of new apertures. Die Untersuchung des hydromechanischen Verhaltens eines zerlegten Felsmassivs erfordert genaue Kenntnisse der einzelnen Spalten. Ziel dieses Artikels ist die Simulation der Evolution des Hohlraumes zwischen den beiden Wänden eines Spaltes während eines Abscherungsexperimentes unter konstantem senkrechtem Druck. Die Ergebnisse der Modellierung werden zunächst mit dem Abscherungsexperiment verglichen und dann im Einzelnen ausführlich analysiert. Während des Abscherungsprozesses tritt eine Öffnung des Spaltes auf, die die Bildung von bevorzugten Fliesswegen fördert. Diese Kanäle werden bereits in einer frühen Phase des Abscherungsprozesses (pre-peak Phase) festgelegt. In der post-peak Phase tritt dann eher eine Vergrößerung dieser Kanäle, als die Bildung neuer Hohlräume auf. L’étude du comportement hydromécanique d’un massif rocheux fracturé ne peut se faire sans une connaissance approfondie des fractures le constituant. L’étude présentée dans cet article concerne la simulation de l’évolution de l’espace des vides présent entre les deux épontes d’une fracture au cours d’un essai de cisaillement à contrainte normale constante. Les résultats du modèle sont tout d’abord validés puis analysés en détail. On constate que, au cours du cisaillement, il apparaît une ouverture de la fracture permettant la création de chenaux préférentiels. Ces derniers sont déterminés très tôt dans le cisaillement (phase pré-pic), et on observe dans la phase post-pic davantage un accroissement de la taille des chenaux plutôt que la formation de nouvelles zones de vides.

Jan 1, 2003

By J. -P. Tshibangu, A. Vervoort, A. Lavrov

Abstract: The aim of the research presented is to study the effect of complex loading schemes on the fracturing process during loading and/or unloading. A first set of experiments was done using a poly-axial cell. These experiments in combination with numerical simulations showed a difference in micro-fracturing (shear and tensile cracks), but not in macro-failure between various loading/ unloading schemes. The second set of experiments was based on the three-point bending test and several cycles with or without rotation between cycles were applied. If the specimen was rotated by 90° or 180° about its long axis between the first and second cycle, no Kaiser effect was observed. Résumé: Le but de la recherche présentée est d’étudier l’effet de schémas de charge complexe sur le processus de fracturation durant la phase de charge et de décharge. Une première série d’expériences était réalisée utilisant une cellule polyaxiale. Ces expériences combinées avec des simulations numériques ont montré une différence de micro-fracturation (fissures de cisaillements et de traction) pour les différents schémas de charge et décharge, mais en ce qui concerne la macro-fracturation ce n’est pas le cas. La deuxième série d’expériences était basée sur des essais de flexion trois points avec plusieurs cycles, avec ou sans rotation entre les cycles. Si l’échantillon est tourné de 90° ou 180° selon le grand axe entre le premier et le second cycle, l’effet Kaiser n’est pas observé. Zusammenfassung: Der Zweck der vorliegenden Forschung bestand darin, den Einfluß von komplizierten Beanspruchungsschemen auf den Bruchprozess im Laufe von Belastung und/oder Entlastung von Gesteinen zu untersuchen. Der erste hier beschriebene Satz von Experimenten wurde mit einer dreiaxialen Belastungsmaschine angestellt. Diese Experimenten zusammen mit dazugehörigen numerischen Simulationen zeigten Unterschiede zwischen Be- und Entlastungsbeanspruchungen in Bezug auf mikrobruchmechanische Mechanismen (d.h. Scher- oder Zugrisse) an, aber nicht in Bezug auf den Makrobruchprozess. Der zweite Satz von Experimenten umfasste Gesteinsbeanspruchung in mehreren Zyklen von Drei-Punkt-Biegung, indem die Gesteinsproben zwischen den Zyklen um einen angegebenen Winkel (0°, 90° oder 180°) gedreht wurden. Falls die Probe um 90° oder 180° gedreht wurde, wurde kein Kaiser-Effekt im zweiten Zyklus beobachtet.

Jan 1, 2003

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magnetohydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2015

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

By D. A. Spencer, L. J. Gardner

In light of the apparent productivity benefits provided by mechanised stoping, Impala Platinum Limited commissioned a study to investigate its possible implementation for mining reserves located 1200 – 1700 m below surface. This paper records the methodology employed for designing a support system for such mechanised mining, as well as initial conclusions of the work done. Preliminary results show the concept to be technically feasible; work was however stopped due to financial non-viability. En considération des bénéfices de production apparents que donne l’exploitation par gradins mécanisée, Impala Platinum Limited a commissionné une étude visant à examiner sa mise en œuvre possible pour des réserves minières situées à 1200 – 1700 m sous la surface. L’étude présente rapporte la méthodologie employée pour créer un système de support pour ce genre d’exploitation mécanisée, ainsi que les conclusions initiales de ce projet. Les résultats préliminaires montrent que le concept est techniquement faisable ; cependant le travail fut arrêté à cause de difficultés de rentabilité. Im Licht des offensichtlichen Produktivitätsnutzens auf Grund mechanisierten Stossbaus, kommissionierte Impala Platinum Limited eine Studie, die dessen mögliche Implementierung für den Abbau von Reserven 1200 - 1700 m unterhalb der Oberfläche untersuchen soll. Dieses Elaborat dokumentiert sowohl die Methode die für das Design eines Unterstützungssystems für eine derartige mechanisierte Abbauweise angewendet wird als auch die anfänglichen Konklusionen der geleisteten Arbeit. Anfängliche Resultate zeigen daß das Konzept technisch durchführbar ist; die Arbeit wurde jedoch wegen der finanziellen Nichtrealisierarkeit gestoppt.

Jan 1, 2003

By C. J. H. Steenkamp

Theoretically, the main driver behind a mining operations? sourcing decision should differ from company to company, and within a company from project to project, but in reality it often relates to cost. Research confirms that there are a number of factors, including cost, to consider when choosing between in-house and outsourced mining. While the literature is rife with factors to consider, little information exists on how to apply these in practice and the relative importance of the different factors to be considered. A study was conducted to determine whether mining is truly a core competency for a mid-tier commodity specialist mining company. Furthermore, a decision-making framework for mining operations sourcing was developed, and the critical success factors that should be adhered to if outsourced mining is chosen were determined. The research showed that owner mining is not a core competency for the mining company investigated. A decision-making framework was developed using the order winner/order qualifier structure, which can be used to facilitate the mining sourcing decision. The most important tools at the disposal of a mine owner?s team to manage a contractor miner are the social and output control mechanisms, according to the critical success factors study.

Jan 1, 2014

Since 2001, the Hybrid Stress Blast Model (HSBM) project members have developed a software suite to model the complete blasting process from non-ideal detonation to muck pile formation. To preserve the physics and improve solution time, the breakage engine uses a combination of analytical models and 2D axisym-metric finite differences to model near-field crushing, coupled to 3D discrete lattice fracturing and distinct element numerical methods to model throw and muck pile development. The model has been validated by comparison with laboratory and field tests in kimberlite. Multiple blasthole simulations are used to demonstrate how changes to blasting parameters can influence downstream efficiencies. Case studies of wall control blasting show that the presplit design must balance the two opposing effects of increased damage with increased charge and decreasing attenuation of the seismic waves with decreasing charge. Modelling of decoupled explosives needs further development. Reducing the charge towards the back of the trim blast results in a much more significant decrease in back damage than altering the timing. The model demonstrates how separation along the weaker planes in a jointed rock can coarsen the fragmentation, leading to inefficient beneficiation, and extends the damage to a distance of at least twice the burden behind from the blasthole, severely compromising the wall stability.

Jan 1, 2012

By D Reddy

Rosh Pinah Zinc Corporation is a zinc-lead mine located in southern of Namibia. It is currently considering the development of a low grade ore body containing about 2.8% zinc. This ore can be utilised by the concentrator if it could be upgraded prior to the ball mill. Preliminary work indicated that the ore may be upgraded in a pre-beneficiating stage by using dense medium separation, X-ray sorting or a combination thereof to a feed grade of minimum 9% zinc. This paper describes the process followed in evaluating the technologies for pre-beneficiation. The results from test work indicated that the low grade ore is amenable to pre-beneficiation by both dense medium separation and X-ray sorting. A comparison between the two technologies showed that dense medium separation marginally outperformed X-ray sorting on grade and recovery. The results for the X-ray sorting were achieved by tuning the calibration curve specifically for the samples tested.

Jan 1, 2008

By Ch. Schroeder, F. Collin, R. Charlier, Y. J. Cui

The paper proposes two numerical models ot the mechanical behaviour of chalk. First, an elasto-plastic constitutive law reproduces the different plastic mechanisms of the chalk and the influence of pore fluids by introducing the concept of suction. Secondly, a model able to reproduce time dependence behaviour. Eventually, the paper gives a simulation of an academic reservoir during depletion and waterflooding phase. Der Artikel stellt zwei numerische Modelle des mechanischen Verhaltens der Kreide vor. Das erste ist ein elasto-plastisches Modell, das verschiedene plastische Mechanismen der Kreide und den Einfluss von Porenflüssigkeit, unter dem Begriff der Suktion, reproduziert. Das zweite Modell berücksichtigt darüberhinaus das zeitabhängige Verhalten. Schliesslich zeigt die Veröffentlichung eine Simulation einer theoretischen Lagerstätte während der Entleerung und der Wasserinjektion. L'article propose deux modèles numériques du comportement mécanique de la craie. Le premier est une loi élasto-plastique qui reproduit les différents mécanismes plastiques de la craie et l'influence du fluide interstitiel par l'introduction de la notion de succion. Le second est un modèle prenant en compte les effets différés. Enfin, l'article présente une simulation d'un réservoir académique durant les phases de déplétion et d'injection d'eau.

Jan 1, 2003

By M. A. van Nierop

Load behaviour in an industrial mill has been measured directly by inserting probes through liner bolts. The data from conductivity probes have indicated the presence of premature centrifuging during manipulation of the load mass. Overloading conditions were also encountered. Overloading and premature centrifuging both reduce the power drawn by the mill. These effects have been successfully modelled.

Jan 1, 1997

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012

By M. Shapiro, L. A. le Grange, B. Henning

A paper was presented by Bateman Minerals and Metals at INFACONX (2004) describing a simplified Computational Fluid Dynamics (CFD) Model for predicting the temperature and velocity distributions in all the fluid zones of a single electrode DC Furnace simultaneously with the temperature distributions in the refractory lining of the vessel. The boundary conditions imposed on the model consisted of the arc current, external surface film coefficients and ambient temperatures. The temperature and velocity distributions in the free-board, slag and metal were solved simultaneously by coupling across the interfaces between the fluids and transportation phenomena developing in the plasma arc. A simplified model was used to describe the ex-change of energy by radiation between the arc and surfaces enclosing the freeboard region. The strengths of this model were reported as being the ability to: ?Solve the different zones and transportation phenomena simultaneously without the need to transfer partial numerical results between different numerical analysis applications. ?Solve velocity and temperature distributions without assumptions regarding internal film coefficients and additional internal temperature boundary conditions. One of the disadvantages of the model was that the energy absorbed by the process was not modelled, resulting in vessel performance predictions under heat loss conditions only. Whilst this allowed potential problem areas such as localized refractory heating to be identified, the model was only capable of predicting how these could be improved by varying the overall geometry and materials of construction. This paper presents improvements in the application software and user defined subroutines of the model as follows: ?Incorporation of surface to gas, gas to gas and gas to surface radiation models to improve the accuracy of radiative heat transfer mechanisms within the freeboard. ?Incorporation of a process energy absorption model based on a theoretical temperature dependant enthalpy curve which incorporates melting, smelting and superheating in selected areas of the bath. This enables the effect of feed distribution and power to feed ratio changes to be estimated. The effects of a commercial arc at full power on the freeboard and slag can now be simulated with increased accuracy.

Jan 1, 2007

By A. McKenzie

During the late 1990s Anglo American PLC was evaluating the Gamsberg zinc deposit in the Northern Cape Province. As the primary South African metallurgical technology provider, Mintek became involved in the evaluation of a pyrometallurgical process for the recovery of zinc from the Gamsberg deposit. eloping DC arc furnace technology for the metallurgical industry. This includes the patented Enviroplas® process for the treatment of zinc bearing waste materials. As a consequence Mintek has developed extensive expertise in the pyrometallurgical processing of zinc bearing materials. However, Mintek?s technologies stopped with the production of Prime Western Grade (PWG) zinc. Early on in the evaluation of the Gamsberg project, it became evident that the refining of PWG zinc would play an important part in the economic viability of the project. At the time the only pyrometallurgical technology available for the refining of PWG zinc to Special High Grade (SHG) zinc was the New Jersey process. This process represents 50-year-old technology and has not undergone significant refinement since the technology was developed. In order to provide a complete pyrometallurgical flow sheet for possible implementation at Gamsberg, Mintek assessed the New Jersey process with a view to either improving the technology or developing a new technology appropriate to the 21 century. In 1998 Mintek convened a consortium consisting of Mintek, the University of Cape Town, Eskom Enterprises, Bateman Metals and Anglo American PLC. The consortium successfully applied to the Innovation Fund for funding to develop a new process for the pyrometallurgical refining of PWG zinc to SHG zinc. The main aims of the project were to develop a new technology for pyrometallurgical zinc refining that conformed to the following: ?Decrease the production cost of SHG zinc metal to stimulate the development of the Gamsberg deposit. ?Be compatible with the current Enviroplas® process, preferably as an add-on to that process. ?Should use electrical energy to benefit from local price tariffs. The project commenced at the beginning of 2000 and consisted of three phases: ?an initial technology search and assessment of the fundamental aspects of zinc distillation. ?the design of a pilot plant for zinc refining. ?the manufacture, commissioning and operation of the pilot plant. A new technology based on a DC arc boiler feeding a packed distillation column was developed and during 2003 the project culminated in the successful operation of a 200 kg/h pilot plant. Ultimately, all of the aims of the project were met and the main outcome is that an advanced process for the pyrometallurgical refining of zinc (the Zincref process) has been developed. The main innovation of the technology was the switch from an energy transfer limited process to a mass transfer limited process (for which a patent has been registered).

Jan 1, 2004