Search Documents

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The question as to whether or not the flow of water through pneumatic rock drills commonly used in this country keeps to a minimum dust disseminated into the air during drilling arose during a study of the dust-in-air conditions in Butte mines from February to July 1936 and December 1936 to June 1937 made by the Bureau of Mines in cooperation with the Anaconda Copper Mining Co., Butte, Mont, The purpose of this report is to describe the study, including some experimental work on the subject, and to give test results.ACKNOWLEDGMENTSThe help of the ventilation department of the Anaconda Copper Mining Co. in planning the study and collecting the data is gratefully acknowledged.EXPERIMENTAL CONDITIONSTests were conducted in an untimbered 6- by 8-foot crosscut in medium-hard granitic rock near the shaft station on an inactive level of one of the active Butte mines. Figure 1 shows the plan and section of the test location. Air was drawn from the shaft at the station, through the crosscut, and up through another shaft. The flow of air through the crosscut was decreased by a brattice downstream from the sampling location, so that relatively high, easily measurable dust concentrations would be obtained in the tests. Impinger samples for determing concentration of dust in the air were collected in an opening 51 inches wide, 29 inches high, and about 4o inches from the top of the rails in a wooden stopping about 16 feet downstream from the place where the test holes were drilled."

Apr 1, 1938

By Jack C. White

The Bureau of Mines, in its efforts to insure the continued viability of the domestic minerals economy, has been engaged for several years in research on the extraction of alumina from domestic, nonbauxitic resources. Hydrochloric acid leaching of kaolin is one of the more promising technologies being studied for recovering alumina for feedstock to existing aluminum smelting capacity; 93 pct of this feedstock is currently imported either as bauxite or alumina. Organics contamination of pregnant leach liquor, originating during solvent extraction for removal of iron from aluminum chloride solution formed during hydrochloric acid leaching, causes rapid deterioration of the semihard rubber lining of process equipment. These organics were removed by a skimming tank-coalescer-activated carbon adsorption system. Organic levels of less than 10 ppm from the coalescer and less than 0.5 ppm from carbon adsorption were achieved. Analytical methods employing CC14 extraction and infrared spectrophotometry were developed to determine the organic content of both the liquor and the carbon. Mass transfer zones delineated in the carbon columns provide adsorption data for the design of larger systems.

Jan 1, 1981

Reduce dust generated during bagging at minerals processing facilities, such as silica sand operations. Approach Installation of a new type of bag nozzle system eliminates the major dust sources during the bag filling process. How It Works The drawing illustrates components of the new bag nozzle system. The system differs in several ways from the conventional nozzle system. An improved bag clamp reduces the amount of blow-back during bag filling, because it has direct contact with approximately 80 per-cent of the nozzle. A two nozzle arrangement includes an inner or "fill" nozzle surrounded by another nozzle, which is designed to exhaust excess pressure from the bag after it has been filled. The exhaust is powered by an eductor, which uses a venturi effect to exhaust the bag at approximately 50 cfm. The exhaust exits into a bucket elevator and is recycled. A pinch valve automatically opens and closes the exhaust system to the bag.

Jan 1, 1984

Continuous remote sensing of air speed In underground mine airways. Approach An ultrasonic technique measures a form of air turbulence which is proportional to air velocity. How It Works The stainless-steel enclosed transducer consists of a sensing head with circuitry, and a telemetry card. The sensor uses a patented ultrasonic technique to measure a form of turbulence created In the air. This turbulence, known as vortex shedding, is related to the air speed through the sensor. Air flowing past a cylindrical post creates vortices which flow down the air stream on both sides of the post. Pulses from an ultrasonic transmitter pass through the vortices to a receiver; the effect of the vortices on the pulses is a measure of air velocity. The transducer contains a telemetry card, known as an accessor, which transmits reports on air velocity through a pair of wires to a monitoring system. The accessor contains an analog-to-digital converter and digital telemetry circuitry required for computer system operation. The transducer does not contain any read-outs or alarms and air velocities are displayed by means of a centrally located

Jan 1, 1982

By Lloyd A. Morley, Alan M. Christman

Introduction A wealth of information exists which deals with electrical grounding, both from a general viewpoint and from a specifically mine-oriented approach. Many parameters must be investigated in order to thoroughly cover all of the variables which govern the performance of electrical grounding systems. The emphasis of this work on open-pit practices re- presents a new development in the field of grounding research, and an exhaustive review of the relevant historical documentation is especially desirable. Grounding System Purposes What purposes are served by a grounding system? The answer is four-fold and may be summarized as follows. First, it must limit potential gradients between conducting materials in a given area (56). When a phase conductor comes into contact with a machine frame, current flows through the equipment, which tends to become elevated above ground by an amount equal to the voltage on the conductor. If a man were to touch the machine while he was simultaneously connected to ground in some manner, his body would also tend to become elevated in potential, possibly to a lethal extent. Thus, the grounding system should provide a low- resistance path for the fault current to return to the source. The maxi- mum potential to which a man could be exposed when touching a machine frame is equal to the voltage drop along the ground conductors inside the power cable, as shown in Figure 1 (54). The ground conductors, therefore, (page # 96 is missing from the original document)

Jan 1, 1976

By Lisa Steiner, Robin Burgess-Limerick

Working with or near underground coal mining equipment is hazardous because of the multiple sources of energy and adverse environmental conditions. Of the 4169 injuries reported to Coal Services during the three years to June 2005,447 were associated with continuous miners, 232 with LHD (load-haul- dump) vehicles, 140 with shuttle cars, and 140 with personnel transport - a total of 959, or 23% of all injuries reported during the period. An analysis of the injury narratives accompanying these injury claims highlights a number of opportunities for controlling injury risks. Using the frequency of reported injuries for the prioritisation of risk control strategies has limitations because of the tendency to underestimate the importance of relatively uncommon but potentially high consequence events. Injury reports also underestimate the contribution of risk factors such as whole body vibration, which have a long-term cumulative contribution to an elevated risk of injury. However, taking these limitations into consideration, the results of the injury narrative analysis suggests the following hazards as the highest priority for elimination or control: • handling continuous miner cable • strain while bolting • slipping off continuous miner platform • inadvertent or incorrect operation of bolting controls, and operation of controls while a person is in a position of danger • hitting potholes or other roadway abnormality • collisions while driving underground vehicles

By L. J. Froisland

The Bureau of Mines conducted a 4-year research program at Uravan, Colo., on a 2-1/2-acre reclamation plot on the slope of a uranium tailings pile that had been covered with mine waste rock. The purpose of this study was to determine the effects of plant species, type of irrigation, type of fertilizers, and use of dust control chemicals on plant growth and surface coverage. Best grass coverage, nearly 100 percent with 240 plants per square foot, was developed in a section that was seeded with crested wheatgrass, fertilized with sewage sludge, and sprinkler irrigated. For comparison, a section that had been treated with commercial fertilizers developed 3.1 crested wheatgrass plants per square foot and 24 percent coverage without irrigation, and 8 plants per square foot and 75 percent coverage with irrigation. Results of spraying a dust control chemical were inconclusive. Russian-thistle invaded all test sections and ranged in density from 0.6 to 7.3 plants per square foot.

Jan 1, 1982

By J. O. Jones

[Willis Mountain in southeastern Buckingham County is one of several kyanite deposits its central Virginia. It is composed principally of kyanite resulting from metamorphism of siliceous sedimentary beds rich in alumina. The mountain, which trends north-south, is 2 miles long and is topped by a narrow ridge with sleep rugged sides rising to an altitude of 1,160 feet and projecting 500 fast shove the surrounding countryside. Bureau Mines engineers examiner Willis Mountain early in 1949, when bonded concentrations of coarsely crystalline kyanite were observed in the kyanite-quartzite on the northern end of the mountain and in loose boulders on the eastern slope. Commencing in late July 1949, the investigations continued on the Long Mountain segment for 11 months, ended in June 1950. A total of 600 samples from 32 diamond-drill holes, aggregating 3,876 feet of drilling, and from 255 feet of sampling in 3 trenches was assayed for kyanite and ferric oxide.]

Jan 1, 1954

By John W. Brown

Electrical resistivity surveys were conducted at three sites in Wyoming in an attempt to detect underground rubble zones in oil shale and to determine their size and resistivity contrast. The zones were detected at Rock Springs sites 4 and 5, but none were detected at Green River site 1. The resistivity of the rubble zones at sites 4 and 5 is greater than that of the surrounding rock. The zones at sites 4 and 5 are concluded to be roughly ovaloid in shape, with a horizontal diameter of 33 m and a vertical thickness of 24 m. Both rubble zones and the blasting that created them are considered to be centered at a depth of 24 m.

Jan 1, 1972

By Charles B. Kenahan

Application of ultrasonics in the electrolytic deposition of metallic manganese and manganese dioxide from sulfate electrolytes had several effects. Ultrasonics produced finer-grained deposits of electrolytic manganese at all current densities than obtained in normal cell operation, but at high current densities it resulted in less adherent deposits. Ultrasonic radiation did not affect cell voltage or cathode current efficiency. In the electrodeposition of manganese dioxide at 70° C., ultrasonic-; increased the current efficiency and decreased the cell voltage at a current density of 9 amperes per square foot, but it had little effect at current densities above this. The decrease in cell voltage was caused by the depolarizing action of ultrasonics at both anode and cathode. Ultrasonic radiation produced a smooth, glossy, adherent, and pit-free deposit at all current densities and at each temperature. Radiation had no effect on current efficiency or cell voltage at 90° C. Ultrasonics was more effective than conventional agitation in producing all of these effects.

Jan 1, 1962

By Will H. Coghill

Titanium is a well-known component of bauxite ores, sometimes occurring in sufficient quantity to mace its recovery worth considering. This question has been raised by some of the companies lixiviating bauxite ores. At the East St. Louis plant of the Aluminum Ore Co., a subsidiary of the Aluminum Co. of America, the waste sludge discharged daily contains over 75,000 pounds of Ti02. The sludge is all through 20-mesh, and a large proportion is slime. A supple of the waste was deslimed so that a gravity-concentration test of the "sand" could be made. The Aluminum Ore Co. cooperated in the work and made the chemical determinations In order to anticipate the results of table concentration a series of specific gravity fractions (float-and-sink) was made with heavy liquids. Acetylene tetrabromide was used for a density of 2.95, methylene iodide for 3.33, and thallium formate for 3.78, and the double salt of thallium formate-malonate made the separation at slimed sample appears in Table 1.

Jan 1, 1928

By T. M. Klemetti, G. M. Molinda, D. M. Pappas

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

By Lippe D. Sadwin

A high-speed streak camera method for making equation of state measurements (shock and particle velocities) on samples of rock under dynamic load conditions is described. Experimental data are given for tests on 12 samples representing 5 rock types. Analysis of these data shows that the method is practical and that good reproducibility of results can be obtained. The pressure range covered in the tests was from 1 to 50 kilobars.

Jan 1, 1966

By R. Ward Stahl

Fire has been one of man's most useful tools through the ages and certainly is a "must" for industrial progress but when uncontrolled is one of the most destructive agencies. This fact is even more important in a coal mine, where many persons and much expensive equipment are confined in a relatively small area. Means of escape from a burning area, as well as from the products of combustion, are often limited; and in many instances the entire surroundings are combustible. Numerous mine fires, which resulted in a high death toll and great financial loss through the years, have caused mine owners to search for the best fire-fighting equipment; much of this has been installed, the quantity depending largely upon the experience of the individual companies or neighboring mines in certain coalfields. A mine owner or operator has meager published information on the actual fire protection afforded and systems of fire-fighting inaugurated in the coalfields, by which he could compare his efforts and get some idea of the adequacy of his own protection. To further general knowledge of the subject, it was decided to survey a representative number of mines in the field and show what has been accomplished. Representative mines were selected in various coal beds; some had similar tonnage, so comparison could be made if desired.

Jan 1, 1957

By H. Robert Ensminger

The Belizean economy had an estimated annual growth of about 3.4% over that of 1986. Economic growth during the 2 previous years was slower and was characterized by a negative trade balance. The gross domestic product (GDP) was an estimated $200 millioni2 in current dollars. Limited natural resources and scarce finances continued to make the Government's task a difficult one. Belize and China signed an economic cooperation agreement in April under which the Chinese Government is to provide technical assistance, a cash grant of $60.000, and a long-term, interest-free loan of approximately $1.5 million. In May, it was reported that gold was discovered in a remote area of the Maya Mountains in western Belize. An estimated unassayed value of $400 million has been placed on the deposit by one of its discoverers. However, the government in Belmopan has played down the discovery. Two U.S. oil companies. Seahawk Oil International of California and Alston Oil Co. of Texas, were granted licenses to explore for oil. Seahawk Oil will explore a large area of the Orange and Corozal Districts, while Alston Oil will prospect a 90,000-acre area of the western Cayo District. Another U.S. oil company, Pecten Oil Co., recently completed seismic studies off-shore of Belize City. Pecten Oil has made plans to start drilling in 1988.

Jan 1, 1989

By Sidney Katell

An estimated capital investment of $76,499,800 will be required for a plant designed and built to produce 90 million standard cubic feet per day (std.c.f.d.) of synthetic pipeline gas through Lurgi gasification of bituminous char. This investment figure does not include the pretreatment plant, the cost of which is assumed to be reflected in the cost of the char fed to the gasification system. Shift conversion, C02 removal, and methanation are required after gasification in the Lurgi unit to make a gas suitable for pipeline transmission. Capital investment data are based upon equipment costs, January 1959. Based on a 90-percent or 330-day operating year, the operating cost before profit and Federal taxes with the char price as a variable will amount to the following: [ ]

Jan 1, 1959

By D. E. Hirsch

The types of compounds present in aromatic concentrates derived from high-boiling petroleum distillates can be estimated from a gel permeation chromato-graphic (GPC) analysis by the use of tables developed from extensive GPC and mass-spectral analyses on fractions from four crude oils. For a fraction from the GPC analysis, the retention volume and the molecular weights (from mass spectrometer) suffice to indicate the types of compounds which predominate. The tables which show these qualitative analyses were developed through the use of pure compounds as well as the extensive analyses on Prudhoe Bay (Alaska), Gach Saran (Iran), Swan Hills (Canada), and Wilmington (California) crude oils. These tables provide a rapid method for determining which types of compounds are present in a GPC fraction before attempting to develop quantitative data.

Jan 1, 1974

By G. V. Sullivan

This report describes an investigation by the Bureau of Mines of flotation techniques for the recovery of chromite from fine-grained disseminated ores. Reported work on the concentration of chromiferous materials shows that flotation has been applied almost exclusively to slime-free pulps. Therefore, chromium recoveries that could be obtained by flotation were related to the amount of slime rejected. However, results of recent studies by the Bureau of Mines showed that des liming is not a requisite to selective concentration of chromite. Laboratory-scale tests on seven ore types from the more important chromium-bearing areas of the Pacific Northwest showed flotation to be technically feasible for treatment of all but one of the samples. Concentrate grades were affected more by the composition of the chromite mineral than by the grade or character of the ore. Test results from three of the samples showed that, without prior desliming of the pulp, 78 to 91 percent of the chromium could be recovered in concentrates of 90 percent or more chromite; two samples responded to similar treatment, resulting in concentrates of more than 80 percent chromite with recoveries of 85 and 89 percent chromium. One sample of mill products, subjected to severe weathering, required removal of the primary slime to obtain a concentrate of 65 percent chromite with only 75 percent chromium recovery.

Jan 1, 1960

By E. D. Calvert

As part of its goal to minimize the requirements for critical and strategic minerals, the Bureau of Mines is conducting research to foster the use of domestically abundant materials such as molybdenum. This report describes the development of an investment shell molding technique that can be used to make castings of molybdenum and its alloys. The mold material is cubic Zr02 with a monoclinic Zr02 binder. The shell, formed by standard investment molding techniques described in the text, is prepared for molybdenum casting by firing for 6 hours at 1,550° C (2,822° F) or for 4 hours at 1,650° C (3,002° F). The resulting castings have predictable and reproducible dimensions with good detail. As-cast strength is poorer than the strength of wrought materials below 1,600° F. At and above this temperature, tensile strengths of cast and wrought materials are nearly equal. Aqueous corrosion of the castings in most media is insignificant.

Jan 1, 1982

By H. H. Schrenk

[A calorimetric method3/ for the determination of benzene in amounts as low as 0.001 m has been developed recently at the U.S. Bureau of Mines Pittsburgh Experiment Station by the authors, with the assistance of chemical personnel from the Allegheny County (Pa.) Relief Works Division. The method is based on the direct nitration of either liquid or gas - phase benzene, followed by neutralization, extraction with butanone, and final treatment with sodium hydroxide which produces a violet color. The color is matched with color standards of known values. Although the method is adaptable to many conditions the primary objective was a procedure that would be suitable for hygienic investigations.]

Jan 1, 1935