Search Documents

By W. D. Bensema, J. W. Adams

A portable, multichannel battery-operated mine-permissible measurement system was developed to measure the rms magnetic-field noise spectrum in the frequency range from 100 Hz to 375 kHz. During each measurement, the entire spectrum is measured simultaneously through the use of time-domain recordings which are later analyzed by Fast Fourier Transform processing. Dynamic ranges of 60 dB in a 125 Hz bandwidth are obtained for spectra covering the range from 100 Hz to 100 kHz. The method also allows a three-dimensional display of the way spectrum occupancy changes with time. Calibration and correction procedures allow absolute field strength measurement with an uncertainty of not more than 3 dB. We feel that further analysis of the system errors will allow this uncertainty to be reduced to less than 1 dB. Ambient magnetic field noise spectra covering frequencies from 100 Hz to 100 kHz are given for several underground coal mine locations. Examples are also given of magnetic field noise on the surface above the mine, noise in the mine face area, noise radiated by specific equipment, the voltage spectrum found on a 600 V dc trolley wire, and noise picked up simultaneously on loops and on roof support bolts.

Jan 1, 1973

By Richard A. Thomas, Isaac A. Zlochower, Gregory M. Green, Kenneth L. Cashdollar, Martin Hertzberg

This paper reports the results of flammability studies for methane, propane. hydrogen, and deuterium gases in air conducted by the Pittsburgh Research Laboratory. Knowledge of the explosion hazards of these gases is important to the coal mining industry and to other industries that produce or use flammable gases. The experimental research was conducted in 20 L and 120 L closed explosion chambers under both quiescent and turbulent conditions, using both electric spark and pyrotechnic ignition sources. The data reported here generally confirm the data of previous investigators, but they are more comprehensive than those reported previously. The results illustrate the complications associated with buoyancy, turbulence, selective diffusion, and ignitor strength versus chamber size. Although the lower flammable limits (LFLs) are well defined for methane (CH,) and Propane (CA), the LFLs for hydrogen (HZ) and its heavier isotope deuterium (D2) are much more dependent on the limit criterion chosen. A similar behavior is observed for the upper flammable limit of propane. The data presented include lower and upper flammable limits, maximum pressures, and maximum rates of pressure rise. The rates of pressure rise, even when normalized by the cube root of the chamber volume (V 1/3), are shown to be sensitive to chamber size.

By Thomas V. Falkie, R. Venkataramani

Proposing A Model In this investigation, a model of the form: n Y = a0 + E a x. A-1 v=l J J was postulated, where the number of independent variables "n" was originally fifteen. The following experimental hypothesis was to be tested: Null Hypothesis: the coefficients a = 0 J Alternate Hypothesis: One or more of the coefficients a 0 J Correlation and Regression To establish the alternate hypothesis and to test how well the proposed model fits the data, the conventional statistical techniques of correlation analysis and multiple linear regression analysis were used. Additionally, factor analysis was employed to investigate the dependency relationships in the data. Correlation and linear regression are well established statistical procedures in science and engineering. References on these procedures include Spiegel (1961), Anderson (1963), and Draper and Smith (1966). A simple example is stated here. If N observations are made of two variables, x and y, and it is desired to test this data to see if a linear relationship exists, then a model of the form: Y = a0 + a 1 x A-2 is proposed. The values of a0 and al may be calculated from the raw data by the "least square normal equations", which are:

Jan 1, 1972

By C. Sunderman, J. Johnson, S. Signer

Researchers at the National Institute for Occupational Safety and Health have developed a miniature data acquisition system (MIDAS) that can measure resistance changes and temperature, store data for later retrieval, and illuminate LED lights. This instrument can be used with strain-gaged bolts, cable bolts, CSIRO stress-measuring gages, string pots, and any other instrument that uses single-ended, resistance-type gages. MIDAS has the capability to measure up to 16 gages at preset time intervals and store more than 2000 scans, yet is small enough to fit in a 35-mm hole. Because the MIDAS consumes little power, a 9-V alkaline battery will operate the system for 6 months. Data from the MIDAS can be sent to a PC via an RS232/RS485/IRdA port. A software program was written to set operation parameters, graph data, and store all information directly to a spreadsheet. Three LED lights change from green to yellow then red based on reading levels and/or rates of change. This feature can be used with different types of gages to warn miners of possible rock instabilities. The MIDAS has received MSHA experimental permissibility approval and is currently being tested at several mines.

By Sam Friedman

The Bureau of Mines conducted experiments using bench-scale apparatus to explore the effect of large changes in process variables on the yield and composition of the gases produced by passing 800° C steam through a fixed bed of Pittsburgh seam (hvab) coal. The total yield of combustible gases increased throughout the given range for the following variables: Superficial steam velocity increasing from 0.02 to 0.12 fps, pressure increasing from 1,000 to 6,000 psig, residence time increasing from 0 to 60 minutes, and temperature increasing from 800° to 900° C; however, a greater increase in the yield of hydrogen in comparison with the increase in yield of methane reduced the gross heating value of the gas to around 470 Btu per scf at conditions giving the maximum yield. Pressures of 1,000, 3,000, and 6,000 psig at 0.09 fps steam velocity, 800° C, and 60 minutes residence time, respectively, produced methane yields of 20, 24, and 22 percent, based on maf coal, with the gross heating value of the CO2-free gas decreasing from 552 to 520 and to 470 Btu per scf. Methane concentrations in the CO2-free gas were 26, 22, and 14 percent, respectively. Based on the gross heating value of the coal, the percentage of the heating value recovered in the gas was 60, 71, and 87 percent, respectively. The use of tungsten sulfide as a catalyst for converting carbon oxides and hydrogen into methane was explored briefly using both a sulfur-free gas rich in methane and a sulfur-bearing synthesis gas (3H2:1CO).

Jan 1, 1968

By P. D. Tracy, M. W. Von Bernewitz

"IntroductionA study of 256 coal-mine explosions, which occurred during the period 1909-1924 killed 4113 men and injured 570 others, reveals the fact that there are the critical times of day when explosions are most likely to occur, and when corresponding care should be exercised to guard against disaster. Of these 256 explosions, 83 straight as explosions, 89 were straight coal-dust explosions, and 81 were mixed gas and dust explosions, while three were undetermined.It has been determined from the times given in these reports (in several cases no times were given,that the critical period in the morning ranges between 6 and 9 o'clock when 83 explosions took place with a peal. at 7;30 o'clock. Of these 55 were straight gas explosions, the remainder being either coal dust or mixed gas and coal dust explosions. The critical period in the afternoon or early ranges between 3 and 7 o'clock, when 113 explosions took place, with a peak at 6 o'clock. Of these, 87 wore straight coal-dust explosions the remainder being neither gas or mixed gas and coal-dust explosions. Between these morning and evening periods is one which might be called the noon period - that is, from 11m to 7. p. m. - when 26 explosions occurred while some of these were normal type of explosions - that is, as to causes - others were of unusual cause and character, and. are discussed later. A number of explosions (29 in all) took place during mid-afternoon, late at night, and early in the morning - that is, after midnight."

Sep 1, 1924

During 1990-1999, a total of 458 fires occurred in all coal mining categories; 157 of those fires caused 164 injuries and 2 fatalities. The greatest number of fues and fire injuries occurred at surface mines, whch also had the highest risk rate values. A total of 66 fuefighting interventions were required. Of these, there were 25 mine rescue team interventions in underground mines, including 5 mobile equipment firefighting interventions, and 41 fire brigade and fire department interventions at all surface operations, including 19 mobile equipment interventions. In all, 50 fires destroyed or heavily damaged equipment (including 16 pieces of mobile equipment) because of failure of other firefighting methods, late fire detection, undetected fires, or fire size. A total of 1 14 fires were detected late by smoke, and 42 fires were not detected.

Reduce well construction and operation costs associated with in situ leach mining while increasing mineral recovery. Approach To accommodate the size of centrifugal pumps presently in use, in situ leaching production wells are typically drilled to 6 inches in diameter, while monitor wells are drilled to measure 4 inches in diameter. However, in order to reduce the cost of drilling these larger diameter wells and to increase recovery, the Bureau has developed jet pumps which have smaller diameters than centrifugal pumps of the same capacity. This allows both production and monitor wells to be drilled smaller. Bureau estimates indicate that the cost of drilling a 3-inch-diameter production well at in situ leaching operations would be about 35 percent less than the cost of a 6-inch well. Similarly, the cost of drilling a 2-inch-diameter monitor well would be about 26 percent less than the cost of a 4-inch well. Such significant savings in the cost of drilling these wells would effect a substantial reduction in total capital cost. Use of the new jet pumps can also increase the percentage of recovery because less costly wells allow closer well spacings, improving the distribution of the leach solution. How the System Works After the borehole is cased, the new small-diameter jet pump, along with piping and accessories, is installed and connected to a centrifugal pumping unit on the surface. High-pressure water from the surface pump is forced through a nozzle into the venturi of the jet type pump injector. This jet action lifts the leach and mineral-bearing solution to the surface.

Jan 1, 1984

By A. L. Engel

The Bagdad-Chase copper-gold mine south of Ludlow, Calif., was visited by an engineer of the Bureau of Mines in July 1955 to determine the mine's status of activity and to obtain a bulk sample for metallurgical testing. The deposit was discovered in 1903 and has been worked intermittently. It has a production record of about 273,000 tons of ore. The first production of about 150,000 tons was treated in a cyanide plant 2 miles west of Barstow, Calif. The extraction of gold was not satisfactory because of the presence of copper minerals. Since 1910 the ore has been shipped to various smelters in Arizona and California for use as a flux.

Jan 1, 1957

By Robert W. Smith

[In a certain application it was necessary to compute the incomplete beta function, ß(1/2, p, q), for a certain set of values of p and q. Since the set of p and q values was much more finely spaced than those in any published tables, the authors have decided to make their results available in this report. In connection with this application, the function ß(1/2, p, q) was needed at various points in the p, q plane at intervals of 0.05, 0.05 p = 2q < 10.00. Fletcher, Miller, and Rosenhead3/ state that the only tables available in the desired range are those of Pearson.4/ However, the interval used by Pearson was not small enough for the present application. For this reason, it was decided to calculate the function ß(1/2, p, q) for p = q = 0.05 (0.05) 10.00. This table is published because of the fundamental importance in mathematical analysis of the incomplete beta function.]

Jan 1, 1953

By J. M. Mutmansky

"The objective of this study was to produce coal dusts for laboratory research that are similar to mine airborne dusts in chemical, mineral, and physical characteristics. In this investigation, dusts produced in laboratory comminution equipment were compared with continuous miner- generated dust for similarity in physical characteristics. Mining-generated dust (MGD) and bulk coal samples were first collected from an underground mining operation. The bulk samples were then processed in the laboratory for size reduction in various comminution devices. These laboratory- generated dust (LGD) samples were subjected to size and microscopic analyses. Physical properties of the dust particles were studied on a scanning electron microscope (SEM ). A numerical shape coordinate system (SCS) was also developed and applied to 300 particles from each sample. Statistical analysis was then performed on the collected data and characteristics of the MGD and LGD samples were compared. IntroductionIn many biomedical studies, researchers routinely introduce a dust mass into an experimental environment to assess the response of a biological entity, usually lung macrophages in vitro or a live laboratory animal, to the dust mass. To provide data of maximum usefulness, it is highly desirable to use dust with characteristics of actual mine airborne dust. The primary objective of this research was to produce dusts in the laboratory similar in chemical, mineralogical, and physical characteristics to mine airborne dusts. This paper outlines the evaluation of the physical characteristics of the lab-generated dusts.Particle shape analysis is perhaps the least-developed area in mineral-related particle science and technology. There are still no standard methods or instruments to scientifically quantify particle shapes. To date, many attempts have been made to characterize particle shapes. These procedures can be roughly classified into three categories:"

Dec 1, 1995

By Thomas M. Kohler, Gerald L. Finfinger, Gregory M. Molinda

The Bureau of Mines has completed an investigation of the effectiveness of methane drainage in the Lower Sunnyside Coalbed at Kaiser Steel Corp.&apos;s Sunnyside No. 1 Mine in Utah. Most of the previous at- tempts to drain methane gas using long horizontal holes were conducted in the Eastern Coal Province. From the high degree of success realized in these efforts and the large body of knowledge gained from associated research, it seemed natural to extend the technology to western coalfields. Previous work had indicated that properties affecting gas drainage were variable in the Sunnyside Coalbed. In an attempt to characterize these properties, four degasification holes were drilled from the out- side entries of an advancing section. The holes were drilled to lengths of 780, 1,680, 1,315, and 1,047 ft and produced initial flow rates of 50,000, 180,000, 340,000, and 240,000 f t3/d, respectively. A total of over 300 million f t3 of commercial-quality gas has been removed from the Sunnyside Coalbed. The four holes have reduced face emissions by 78 pct.

Jan 1, 1986

By E. P. Youngman

The mining law of Chosen, which was made effective April 1, 1916, was promulgated as ordinance 8, December 24, 1915, in accordance with the provisions of articles 1 and 2 of law No. 30 of 1911. The new le repealed the mining law, Fo. 3 of 1906, and the placer mining law, No. of 1906, and in effect annulled all prior mining legislation. An amendment to the mining law of 1916 (by virtue of law No. 30 of 1911) vas. passed December 16, 1918, as ordinence o. 17. The detailed regulations, which were to supplement the law proper, and rich in all probability follow closely the regulations in force in the Empire, were not available. Unless otherwise indicated, references in this paper are to the mining law of 1916.

Mar 1, 1933

Develop a reliable, portable device for non-destructively testing the support integrity of a friction rock support (commonly referred to as a Split Set ). Approach The friction rock support, used to support mine roof and ribs, is a slotted tube driven into a drilled hole of smaller diameter. Upon installation, the tube is compressed radially. The amount of compression is a function of the hole diameter, the strength of the host rock, and the properties of the split set itself. A simple lightweight self-contained device was developed to determine the pull-out resistance of the friction rock supports in-situ, based on measurements of the tube&apos;s deformation. The tester measures the com-pressed internal volume of the slotted tube, which has been found to provide an estimate of the support&apos;s resistance to pull out. How It Works The tester consists of a pump and expander sections. The expander sections are made from an elastomer membrane which is stretched over two cores, each one inch in diameter and twelve inches long. The expanders are connected by a flexible coupler so that they can fit any alignment of the support.

Jan 1, 1984

By John G. Kovac

A computer simulation has been developed to estimate the chances of a miner making a successful escape while wearing a SCSR. The model takes into account: (1) training in the use of SCSRs, (2) apparatus integrity, and (3) the oxygen cost of a mine escape. This Bureau of Mines report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

Develop a technology for producing high-quality hake graphite from the steelmaking waste known as kish. Approach Treat the waste kish as an ore and apply mineral processing techniques of physical beneficiation and chemical purification to produce a range of graphite products com¬petitive with the natural mineral. Background Graphite is a naturally occurring form of carbon with a unique combination of properties that make it indispensable in a very wide range of industrial and consumer applications. It has high electrical and thermal conductivity and remains stable to extremely high temperatures It has a low coefficient of friction and is nearly impervious to corrosion. The steel industry is dependent on graphite in clay-, magnesia-, and alumina-bonded refractories for crucibles, bricks, facings, and coatings. Electrical uses include graphite brushes in motors and generators, and electrodes in batteries. The transportation industry needs graphite for clutch and brake linings, and all industries depend on graphite in seals, gaskets, lubricants, and coatings. The consumer sees graphite in composite plastics and in the common pencil. As with all natural minerals, the availability of graphite is diminishing and costs are rising as quality decreases.

Jan 1, 1993

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR&apos;s), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR&apos;s from 1982 through 1990. The SCSR&apos;s were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 2010

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 1,040 Bcf as of January 1, 1987. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 265 Bcf, (2) helium in probable natural gas resources, estimated at 228 Bcf, (3) helium in possible natural gas resources, estimated to be 320 Bcf, and (4) helium in speculative natural gas resources, 227 Bcf. These helium resources are further divided into depleting and nondepleting, with the helium in storage being in a separate classification. The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. Almost all of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 951 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, i.e., those in shut-in, abandoned, or otherwise nonproducing natural gasfields, are estimated to total 53 Bef. There is 36 Bcf of helium in storage in the Federal Government-owned Cliffside Gasfield near Amarillo, TX.

Jan 1, 1988

By M. J. Ankeny, J. J. Forbes

Several sets of questions and answers on the fundamentals of first aid to the injured, based on the Manual of First-Aid Instruction of the United States Bureau of Mines, are now in use in various parts of the United States. Persons experienced in first-aid instruction believe that a standardized set of questions and answers will assist materially in preparing men for examin- ations conducted by the Bureau for first-aid certificates. Inquiries as to whether a set of standardized questions and answers is available have been made frequently by those training men for the Bureau of Mines examination for certificates. It is believed that the following list of 171 questions and answers com- piled directly from the manual will be useful to company officials and em- ployees who are engaged in cooperative first-aid training to qualify for Bureau of Mines certificates. The list may also be used by field men of the Bureau in training instructors preparatory to a cooperative training campaign and in examining classes or individuals for first-aid certificates. The page references in parentheses refer to pages in the Manual of First-Aid Instruction.

Oct 1, 1935

By Peter Krause

This report provides an overview of the worldwide photographic industry and of the applications of photography. It also covers important technological and market trends, with special emphasis on those factors which may affect the consumption of silver in the future. The text is divided into the following eight sections: 1. Principal manufacturers of silver-based photographic products 2. Major product sectors 3. Structure of the international market for silver-based photographic products 4. Silver-bearing raw materials for the manufacture of photographic products 5. Processing of photographic products: recovery of silver and recycling 6. Methods for estimating the use of silver in photographic products 7. Basic function of silver in photography and alternate image capture and recording systems 8. Brief history of photography Silver- based photographic materials are made for many applications that require different photochemical and physical response characteristics and a wide variety of formats and sizes. All of these products are laminates consisting of a surface-treated support and bonded gelatin layers. Two basic types predominate - films and papers. Films have transparent or translucent plastic supports (mostly cellulose tri-acetate and polyester), while papers have mostly a paper core coated with polyethylene resin layers on both sides (RC type). The front layer contains white titanium dioxide to provide high reflectivity and the back layer a matting agent. However, a few so-called fiber base papers are still supplied. These have a high quality paper base coated with a baryta layer ; i.e. a gelatin layer containing white barium sulfate. The manufacture of photographic film and paper supports requires special procedures and equipment, because of the severe requirements for chemical purity, optical integrity and uniformity (see Table 1 on page 10 for a list of the principal makers of film and paper supports).

Jan 1, 1992