Search Documents

By Kenneth E. Hjelmstad

In situ leach mining operations often encounter difficulty maintaining adequate leach solution flow into the are formation. Swelling and dis-persion of clay particles in the formation are often responsible for this permeability loss. Permeability and leaching tests were done in the laboratory on clayey ores to evaluate a clay-stabilizing polymer's effectiveness in preventing these problems. Test results indicate that treating the ores with the stabilizer could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability-leaching tests. Since in situ leaching throughput rate is directly related to permeability, these results also indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure. To determine the reasons for the success of the clay stabilizers, an investigation was conducted to cieter-mine the effect of the stabilizer on clay swelling and dispersion. Clay-swelling tests indicated that the clay stabilizer reduced clay swelling. Zeta potential measurements made on fine clay particles treated with the stabilizer were compared to measurements made on untreated particles and indicated that the stabilizer was electropositive and, therefore, could reduce the degree of negative charge on the particles and their tendency to disperse or migrate.

Jan 1, 1984

Although the technology involved in removing material from below the earth's surface has a long history, communication systems in underground workings are relatively new to the industry. Communication equipment did not begin appearing in underground mines until the early 1900's. Figure 1-1 shows a miner using a Western Electric standard telephone set for underground mines in 1913. These early phones were essentially the same as those used aboveground, except that they were enclosed in cast-iron boxes as protection against moisture, acid fumes, and gases.

Jan 1, 1984

By William I. Nissen, Richard Havens

Continuous flotation studies were made at a 50 - lb - per - hr feed rate to confirm the effectiveness of a batch - scale procedure for concentrating phenacite and bertrandite minerals from Mount Wheeler ores that contained , in percent , 0.47 , 0.78 , and 4.7 BeO . The procedure for selective froth flotation of the beryllium minerals from a gangue composed chiefly of calcite , fluorite , and mica comprised closely controlled preconditioning with sodium fluoride and sodium hexametaphosphate in a series of small mechanically agitated tanks and use of a mixture of oleic acid with kerosine , fuel oil , or turpentine as a collector . It was difficult to adapt the laboratory flotation procedure to continuous operation . The principal problem of achieving adequate conditioning to depress calcite and fluorite ultimately was resolved by conditioning in series . Thereafter , three ore samples of different grades treated on a continuous basis yielded concentrates containing from 12 to 25 percent Beo from these relatively complex and difficult ores . Recoveries , on a BeO basis , ranged from 75 to 88 percent . Losses , which primarily were due to incomplete liberation , probably could be lowered in a commercial operation .

Jan 1, 1964

By R. V. Ramani, R. L. Grayson, R. L. Frantz, V. A. Marple, W. R. Myers, K. L. Rubow, Mutmansky. J. M., T. J. Stobbe

"An investigation of protocols for research performed from 1953 to 1988 on pneumoconioses (with emphasis on diseases related to coal and silica) was conducted in the Generic Mineral Technology Center for Respirable Dust. In addition, interviews were conducted with prominent U.S. medical researchers, aerosol scientists and engineers in government, industry, and universities to determine dust sources, dust preparation methods, laboratory protocols, and determinant variables related to in vitro and in vivo research and assess the comparability of results.Since the original report on the protocol project, additional research regarding free radical existence in freshly produced dust particles and the shape and contamination of particles generated for research purposes has further heightened scientists' concerns. As indicated by current research, fresher dust particles and those with more angular shapes may have a different level of reactivity in biological systems than do older or more rounded particles. Therefore, research on dust preparation methods for biomedical studies was undertaken and will be outlined here.Results of protocol review and interviews are summarized. Research on size reduction methods and their particle characteristics plus some recommendations concerning dust preparation methods and reporting in biomedical publications are also presented. Recent evidence indicates that these recommendations may be of importance in comparing and interpreting research results."

Nov 1, 1995

By L. L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P205, is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pct P205 and a P205 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1981

By W. Beckering

In characterizing tars obtained by the low-temperature carbonization of North Dakota lignite, infrared spectra have been an invaluable aid in both qualitative and quantitative examination. Quite, early in the tar-research program of the Federal Bureau of Mines it became evident that the small number of published spectra available for hydroxy-aromatics would be inadequate for comparative purposes when dealing with the wide range of compounds present in coal tar; therefore, compiling a catalog of spectra was begun as a continuing part of the tar program. Because these spectra should be valuable to other investigators in this and related fields, they are being presented in these reports. This supplement to the original publications presents the spectra (figs, I to 32), representing 32 compounds, largely phenolic materials. The major problem of this project has been the availability of materials for examination. Most of the compounds included in this supplement were synthesized at the Bureau of Mines Lignite Research Laboratory. Some were obtained from commercial sources, whereas the compound 2'-hydroxy-l-phenylnaphthalene was synthesized at the Bureau of Mines laboratory in Bruceton, Pa. The spectrum of 2-ethyl-4-methylphenol, figure 32, is a correction of the spectrum presented as figure 26 in the original reports

Jan 1, 1961

By S. L. May

The Bureau of Mines has developed several methods for extracting tantalum and columbium (niobium) and the rare-earth compounds from ores and concentrates. A cooperative agreement was made by the Bureau with Porter Bros. Corporation of Idaho to process 200 pounds of its euxenite concentrate by methods that had been developed at the Albany, Oreg., Metallurgy Research Center. The euxenite concentrate was processed to extract and purify the valuable metals by chlorination, solvent extraction, and hydrometallurgical techniques. Chlorination was used to convert the valuable constituents into chlorides and to partly separate them. Solvent extraction techniques were used to separate the tantalum from the columbium. The rare-earth and uranium compounds were purified by hydrometallurgical methods.

Jan 1, 1959

By P. G. Bennett

The Bureau of Mines developed a process using ion exchange to recover cobalt from spent copper leach solutions. A preliminary economic evaluation of the process indicated that about one-third of the capital cost was attributed to the total resin inventory, and one-third of the operating cost was required for reagents to remove iron from the ion-exchange eluates. An agitated Pachuca elution system was investigated in place of a fixed-bed elution system. The Pachuca system reduced the resin inventory by 27 pet when compared with the fixed-bed elution system. Processing fresh spent copper leach solution reduced the resin inventory by 20 pct and resin iron loading by 80 pct. Reagent requirements for removing iron from the eluates were decreased because less iron was extracted. The Pachuca system, along with processing fresh spent copper leach solution, reduced the total resin inventory by 47 pct. A revised cost evaluation of the cobalt recovery process was obtained to determine the effects of these process modifIcations. The estimated total capital cost for a plant processing 10,000 gpm of spent copper leach solution containing 26 ppm Co was $23.1 million. With credits for nickel, zinc, and copper byproducts, the estimated net operating cost was $5.10/lb of cobalt.

Jan 1, 1988

By Frank J. Wiebelt

In its efforts to maintain production of tungsten during the recent war period, the Bureau of Mines explored certain parts of the properties of the Atolia Mining Co. in San Bernardino County, Calif., by diamond drilling. Owing to past production record and other available data, the area was considered attractive for possible development of new ore bodies. Scheelite occurs in narrow veins ranging in width from a fraction of an inch to several feet. The veins are in quartz monzonite in a zone 2 miles long and 500 feet wide. Production from the district was reported to have been over 1,000,000 units of W03. Twelve diamond-drill holes, totaling 5,056 feet, were drilled by the Bureau of Mines in the vicinity of the Papoose, Papoose No. 5, Amity, and Union mines, the tailings pond, and the "Old Spud Patch." The work began in August 1943 and was completed in June 1944. This publication briefly describes the history and deposits of the district and gives full details of the work performed by the Bureau.

Jan 1, 1950

By G. R. Peterson

The Bureau of Mines evaluated the potential supply of cobalt from known domestic resources, both as a primary product from some deposits and as a byproduct from others, and found that U.S. production could play an important role in meeting U.S. cobalt needs by the mid-1980's. This production would be of a relatively short duration, however, with production declining significantly before the year 2000. As part of the study, a tonnage-price relationship was developed indicating the quantity of cobalt that could be produced from known cobalt-bearing deposits at various primary commodity prices and at a 15-percent rate of return on the required capital investment. All capital and operating costs are calculated in August 1980 dollars, and commodity prices are based on August 1980 prices. Known U.S. cobalt-bearing deposits which represent the current U.S. cobalt reserve base contain some 310,800 metric tons of cobalt in slightly over 1 billion metric tons of demonstrated mineralized material. Approximately 37 percent of the cobalt contained in the reserve base is considered recoverable using existing technology. Of this quantity, some 87,000 metric tons of cobalt is economically recoverable assuming a cobalt price of $25 per pound, a copper price of $1 per pound, and a lead price of $0.40 per pound. Assuming that the cobalt price decreases to $15 per pound, keeping copper and lead prices constant, the quantity that is considered economically recoverable declines to some 45,700 metric tons. Domestic cobalt consumption in 1979 was 7,900 metric tons (17.4 million pounds). Currently, no primary cobalt is produced from domestic resources, and none has been produced since 1971.

Jan 1, 1981

By Bruce I. Thomas

The occurrence of tin-bearing gravels along Tozimoran Creek in central Alaska has been known for a number of years. In September 1944 the Bureau of Mines investigated an area approximately 1,000 feet long and 200 feet wide along Tozimoran Creek to deter-mine the cassiterite content of the stream gravels, which are about 4 feet deep and covered by 3 feet of overburden. Nine trenches and two shafts were excavated, from which samples of the underlying gravels were taken. This report contains a discussion of sampling methods and tables giving the results of analyses.

Jan 1, 1948

By Sara J. Davenport

Hydrogen sulfite has been listed (1)3/ as a possible hazard in 50 occupations, many of which are in the mineral industries. The effects of its occurrence in the petroleum industry made themselves felt more than two decades ago, resulting in a comprehensive study (2) of the toxic gases from Mexican and other high-sulfur petroleum products. The mining industry, likewise, has had cause to guard against this gas. Enough hydrogen sulfide has been found in coal and some noncoal mines during normal operations to cause severe eye irritation, some serious illness, end even fatalities. It is usually a product of the decomposition of sulfur compounds and may be produced by burning explosives containing sulfur; the gas in harmful qauntities is formed by the use of block blasting powder or by the use of dynamite in blasting sulfide ores. Hydrogen sulfide is readily soluble in water, and enough may be released from water streams in coal and noncoal mining to cause fatal poisoning it is found sometimes in stagnant water underground, particularly where ventilation currents are absent, and great care must be exercised when accumulations of such waters are disturbed, as exposure to comparatively low concentrations of the gas evolved therefrom has caused fatal accidents.

Jan 1, 1945

By Fredrick L. Johnson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 25,640 acres of the 29,680-acre Devil?s Garden Lava Bed, 21,040 acres of the 28,660-acre Squaw Ridge Lava Bed, and 9,100 acres of the 12,600-acre Four Craters Lava Bed Wilderness Study Areas (OR-D01-D02, OR-001-003, and OR-001-022, respectively) in order to evaluate their identified mineral resources. The study areas are located in Lake County, OR, about 50 air miles southeast of Bend. No mineral resources were identified in the three study areas. The areas are almost entirely underlain by recent lava flows. Cinder cones occur in each of the areas; however, the best cinder occurrences are in the Four Craters Lava Bed study area. Slab lava, of facing stone quality, is scattered throughout the Devil?s Garden Lava Bed study area, and to a lesser extent, in the Squaw Ridge Lava Bed study area.

Jan 1, 1987

By Steven W. Schmauch

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 27,930 acres of the 52,000 acre East Fork High Rock Canyon Wilderness Study Area, CA-020-914/NV-020-006A, in order to evaluate the mineral resources. The study area is located in Humboldt and Washoe Counties, NV, about 45 miles east of Cedarville, CA. Bureau of Mines personnel reviewed pertinent literature and county mining records and examined prospects or mineralized areas. There are no organized mining districts and no historical or active claims in the study area; one small pit lies in the southwest corner of the study area. Based on published literature, sample results and field observations, there are no recognized mineral, geothermal, or fossil fuel resources. Epithermal mineralization indicators are not present or exposed. Sand and gravel deposits in the study area are not likely to be developed as other deposits are closer to market areas.

Jan 1, 1986

By L. L. Oden

The Bureau of Mines analyzed vapor-aluminum-diffused stainless steels prior to conducting corrosion measurements in severely sulfidizing environments. These studies were conducted in response to the national need to better control the environmental and economic costs of corrosion. Specimens of a ferritic alloy and austenitic alloys types 316 and 310 were treated by a proprietary vapor-aluminum diffusion process and a dual vapor-aluminum diffusion process. Weights and dimensions were recorded before and after treatment, and comprehensive metallographic, X-ray, and electron micro-probe analyses were conducted for both single-and dual-vapor-aluminum-diffused specimens. Surface aluminum concentrations ranged from 26 to 34 wt-pct for all alloys. Dual treatment increased the quantity of aluminum per unit area by a factor of 2 and increased the depth of penetration by a factor of 3. The aluminum-diffused region of the ferritic alloy was single-phase aFe solid solution that was ordered on the surface, whereas two distinct diffusion layers were ob-served on the austenitic alloys. The outer layer comprised aFe solid solution that was ordered on the surface, and the inner layer was a two-phase mixture of aFe solid solution and the interrnetallic compound AINi.

Jan 1, 1982

By Arnold O. Tanner

The recession that took hold of the domes-tic mining industry in 1981-82 finally abated somewhat in 1987, resulting from increases in many commodity prices, especially in the metals sector, and from continuing success in lowering operating costs. By no means was the work finished; the mining industry was in a sense entering a new era. The struggle for survival was still very evident for many companies and various commodities, but increasing productivity and profits were accompanied by indications that these trends were more long term than short term. Raw nonfuel minerals produced in the United States during 1987 had an estimated value of $26.3 billion, an increase of $2.9 billion over the 1986 value. This is the fifth consecutive year that the value has increased. Except for a decrease in 1982, the value each year has increased since 1971, or 15 of 16 years. The value of raw metals production increased by an estimated 28%, an impressive improvement since the drastic fall in 1982. Industrial minerals growth was comparatively flat, with an estimated in-crease in value of 0.1 %, continuing a trend of the previous 2 years. Metal mine production dropped considerably in 1982 and maintained its resultant lower level until 1987, when production significantly recovered.

Jan 1, 1989

By John S. Dunning

This paper is one of a series describing methods and costs of recovering sand and gravel from deposits in the United States and deals directly with the operations of the Atlas Sand, Gravel and Stone Co. at Farmington, Conn. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local expenditures only and not total production costs. It is recognized that publication of total costs might in some instances cause embarasement to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations may ensue.

Jan 1, 1933

By Charles L. Kimbell

The final 26 tables of this chapter, tables 25-50, extend and expand the statistical series on production that was started in the 1963 edition of the "Area Reports: International" volume of the "Minerals Yearbook" and that was subsequently updated and expanded in the 1965 and 1967-89 editions. Continuing the practice started in 1989, a column has been included in each of these tables providing a 5-year average for 1986-90, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1990. With the inclusion of silver and uranium in the 1988 edition of this chapter, this group of tables now includes each of the crude minerals that ranked from 1st to 19th in 1983 terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93% of the estimated value of world crude mineral production in 1983. In addition, world output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-are included because of their significance as products.

Jan 1, 1993

No noticeable international economic recovery occurred during the first half of 1982. Industrial production continued to fall in the United States, Canada and Italy and to hold steady in France. Modest increases in production occurred in Japan, England and Germany, although some decline took place from March to April. The U.S. mining industry has been more severely affected by the world recession than the U.S. economy. This is not immediately obvious when comparing the U.S. mining industrial production index from 1981 to 1982, which decreased 8.5 percent, as compared to a 7.1 percent decline for total domestic industries. However, "mining" industry statistics in the U.S. national economic accounting system include petroleum and natural gas as well as minerals. When metal mining is isolated, the decrease in production from 1981 to 1982 is 19.3 percent. If metal mining production continues to perform at the same rate during the third and fourth quarters of 1982 as during the first half of the year, declines from 1981 levels will be quite severe. Aluminum will have declined 22 percent, copper 18 percent, iron ore 24 percent, lead 3 percent, steel 29 percent, titanium 2 percent and zinc 25 percent.

Jan 1, 1982

By D. A. Reynolds

The Bureau of Mines-American Gas Association survey of the carbonizing properties of American coals was begun in 1929, and has been continued almost without interruption since that time. Upwards of 100 coals have been carbonized at low, medium, and high temperatures in this survey, and about 200 additional coals have been carbonized at high temperatures only. All survey coals were blended with coal of different rank for carbonization at one high temperature (900° C,). During the past few years, 12-high-volatile A coals were blended with Pocahontas No 3 coal from Kimball, McDowell County, W. Va., and in this report the physical properties of the cokes from these high-volatile coals and their blends are compared.

Jan 1, 1949