Search Documents

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964

By W. F. Watts

The U.S. Bureau of Mines has conducted research on methods to reduce and to measure diesel particulate matter (DPM) aerosols in underground coal mines. One objective of this report is to present findings from an investigation of the DPM reductions obtained by an engine-mounted integrated control system consisting of a dry system (DS) and a diesel particulate filter (DPF). Another objective is to present results from the usc of a size selective personal sampler to measure DPM concentrations in an underground coal mine. Bureau laboratory tests of the integrated dry system and diesel particulate filter (DS-DPF) have shown that DPM emissions can be reduced up to 97 pet with little change in gaseous emission concentrations. The DS-DPF is undergoing certification tests conducted by the Mine Safety and Health Administration (MSHA). Subsequent to passing all safety requirements, it will be tested in an underground coal mine. A baseline survey of DPM concentrations and aerosol size distributions in a cooperating mine was completed in August 1988. A prototype DPM personal sampler was tested during this survey. Based on results from this test, an improved unit has been developed. This unit is scheduled for extensive field testing by MSHA in 1989.

Jan 1, 1989

By J. K. Whyatt

During the past 2 years, U.S. Bureau of Mines (USBM) researchers reviewed an in situ stress investigation conducted in 1977 at a test site on the 4250 level of the Lucky Friday Mine, Mullan, ID. Although the field measurements of over core strain were found to be useful, significant deficiencies were found in the stress field estimation procedure. The stress field estimate was then updated to incorporate recent progress in statistical capabilities and new understanding of stress concentration factors for doorstopper cells, as well as to correct an error in the original stress solution procedure. Simple models were used to examine the possibility that systematic variations in material properties and stress fields existed at the site. These models succeeded in reducing the sum of squared error somewhat, but fell short of completely describing stress variations throughout the test site. This overcore measurement will be supplemented by two other measurements described in the second and third reports of this series. Other observations of stress field characteristics are discussed in the fourth report The final report will also characterize the natural in situ stress field in the vicinity of the Lucky Friday Mine. This work was undertaken to support USBM research on mining method design and rock-burst control for deep mines.

Jan 1, 2010

This section of Minerals and Materials analyzes the following three factors affecting the recent performance of the U.S. and world mineral industries: 1) the health of the U.S. and world economies, 2) the level of interest rates and 3) the performance of productivity in both the U.S. mineral industry and the general economy. While these indicators do not exhaust the possible critical factors, they represent an initial attempt to probe some of the considerations underlying the performance of the U.S. minerals and materials industry. The U.S. and World Economies It is essential to analyze the state of the U.S. and world economy because the demand for minerals and materials is a derived demand; that is, since minerals and materials are used in the productive process, the demand for them is a direct function of the demand for the finished products of which they are a basic input. Thus, the demand for minerals and materials is directly affected by changes in present and planned consumption and investment expenditures. The past two issues of this publication have highlighted the generally discouraging performance of the national and inter-national economies. Briefly, the world economy is in the third year of the first long recession in recent history where inflation rates have remained above 5 percent. With many countries either unable or unwilling to support domestic spending while inflation continues, there has been a growing tendency to institute trade-restrictive policies to support domestic demand. The resulting weakened demand conditions in exporting nations have had a direct effect on the mineral industry.

Jan 1, 1982

By L. J. Froisland

An integrated process for recovering metal from nonmagnetic auto-shredder reject scrap was investigated by the Federal Bureau of Mines. The methods used were air classification, water elutriation, screening, magnetic separation, handpicking, and heavy-media separation. Metal recoveries in this process were projected at 39 percent copper and copper alloys, 53 percent aluminum, 96 percent iron, and 98 percent zinc die cast. An economic evaluation of the conceptual process indicated that a facility designed to reclaim the reject scrap from 200 shredded automobiles daily could be profitable. Total investment in this plant was estimated at $321,000; the discounted rate of return before taxes was 53 percent.

Jan 1, 1975

By David Schlain

The galvanic corrosion properties of titanium and zirconium were investigated by the Bureau of Mines. The dissimilar metals involved in these experiments included magnesium, magnesium alloy FS1, aluminum alloys, zinc, steel, tin, lead, copper, Monel, nickel, and several stainless steels. Couples were immersed in synthetic ocean water, tap water, 5-percent ammonium sulfate solution, 5-1/2-percent sodium chloride solution, sodium hydroxide solution, 0.1 N hydrochloric acid, and various concentrations of sulfuric acid.

Jan 1, 1956

By Guy A. Johnson

To improve productivity and cut costs, modern underground mining operations have become more mechanized. This mechanization has increased the usage of fuels, hydraulics, and electrical equipment associated with diesel-powered vehicles, thereby also increasing the hazards of underground mine fires. The Bureau of Mines evaluated the fire hazard problem and assembled prototype components for a system that would automatically sense and extinguish fires on mobile underground equipment. The prototype system and alternative designs were in-mine-tested and proved effective. This report summarizes this technology, which can cost effectively help solve the problem of fire hazards on underground vehicles.

Jan 1, 1983

By E. D. Gordner

Irrespira ble gutses issuing from the rock fofflb tions ere tJ source of expense ond danger in some metGLl mines. There is a great Variation in the compos i-· tion of such gdses and, os shown 'by recent sampling by the Bureau of ines, the gas rr;;,.y consi$t mostly ct carbon dioxide, (Rocle Strata Gtsses in the Mines of the East Tintic Mining District, by G. E. McElroy, Bu.retau of Mines Serial 2Z75) or f methone (Metruine in Ccalifornia C.old Mines, by B. 0. Picl-Q:lrd i:lnd !.. D. ("iordner, Bure, cf Mines Serial 2303), or nitrogen, sin the present instonce. A nl.liilber of unventilated rt:t.ises in some of the mine of l:l Neva&. district conuin «i'ccumulCltions of l;i hih-nitrogen gas the1t will not supi:ort life or combus­tion. The rdises ore in different geologiecil formations and in widely sep1:1rated. loecslities in the mining district. One ot" two ri::lises in the sme fc.rtr.ation may be full of the gos cand einother nec-r'by be t'ree ot· it. Lives have been lost t:lnd a number of men heave been overcome on enteing unvetilated rtsises in which their­respircable tss hcsd c1ccuni..1.l1::1ted between sldfts. Gener1:1lly, however, the gas see:ns to noozett from the .t'onrbtio:1 ond to ecc1: .. ,i.-1,;.1:.1te so slowly tMt its presence is not suspected t the tfr.1e, bu.t discovered. ed:'t&.c' the raise is t)band.oned. OcCE.isionelly 1 t issues from a ne•.,ly cut cre·tice or fissure under considerca ble pressure and in lar!?e enough '3.'16ntities to overcome or drive 011t men working in unventilated places.

Dec 1, 1922

By J. A. Eisele

The Bureau of Mines conducted bench-scale cyclic tests to determine the composition of recycled leach liquor in the Bureau?s proposed clay/HCl leach/ HCl sparge process for producing Al203 from clay. The data developed from these tests make it possible to synthesize leach liquors for predetermined steady-state operating conditions when conducting large-scale crystallization tests. The results of two sparge tests were compared. One was a 20-cycle test with a 36-pct-HCl concentration in the mother liquor; the other was a 10-cycle test with a 26-pct-HCl concentration in the mother liquor. The effect of impurity concentrations in the leach liquor on the purity of aluminum chloride (AlCl30?6H20) crystals was determined, but there was poor correlation between this data and results that have been obtained from miniplant-scale work.

Jan 1, 1980

By Edward L. Tullis

Numerous widely distributed pegmatites of the southern Black Hills of South Dakota contain small amounts of beryl, and two minor deposits are known in the northern Black Hills. Few mines have produced more than 50 tons, and the current, rate of production for the area is about 100 tons annually. Total production, since the first records, is 2,358 tons. Most of the deposits contain less than 1 percent beryl, although the beryl zones in several deposits contain 2 percent beryl or more. Estimated reserves of beryl total 11,824 tons, and an additional 234 tons has been measured; there are other unestimated reserves. The pegmatites are in a belt about the margin of the Harney Peak batholith in the southern Black Hills, although they fail into three districts. The most important, from the point of view of production and reserves, is the Keystone district. Many deposits also are found in the vicinity of Custer and Pringle. Small amounts of beryl occur in the dikes near Hill City. A little beryl has been produced from the Tinton district in the northern Black Hills, and an undeveloped dike has been discovered on Whitewood Peak near Deadwood. The beryl-bearing pegmatites are principally coarse-grained intergrowths or massive segregations of feldspar, quartz, and mica. Some of them contain notable amounts of lithium minerals, as well as some tantalite, columbite, and cassiterite.

Jan 1, 1952

By David W. Tongue

This report describes the engineering work leading to the design of an underground coal mine piping system to transport approximately 2,000,000 cubic feet per day of methane gas to the surface from degasification holes drilled horizontally into the coalbed in existing coal mines. Safety instrumentation for detection of gas leaks and provisions for automatic emergency shutdown are included in the design. It also includes specifications for a safe system of handling gas, water, and drill cuttings during drilling of the horizontal holes and recommendations for compressor and metering facilities at the surface. The main pipeline is recommended to be constructed of polyethylene plastic pipe joined by a butt fusion method while lateral lines and separator and meter piping at the horizontal holes are recommended to be screwed steel piping. The materials used are to be resistant to the forces of impact exerted by falling rock. The pipelines are to be suspended from the ceiling with pipe hangers. All steel components are protected from chemical corrosion by applying protective coatings and the vertical casing to the surface is protected from electrolytic corrosion by a rectifier station. Methane gas detectors monitor the mine atmosphere to detect the presence of gas leaks and a pneumatic plastic tubing line provides for control of the safety shutdown system. Both the recommended design and the required construction procedures are in compliance with the applicable Federal codes for coal mine safety.

Jan 1, 2012

By J. P. Bennett

The Bureau of Mines investigated the dimensional changes of ceramic materials exposed to acid environments to evaluate construction materials for emerging technology in chemical and metallurgical processes. Six commercial ceramic materials (two red shale, two fireclay, one silica, and one silicon carbide (SiC» were exposed to H20, 20 and 30 wt pct HCl, 40 and 60 wt pct HN03, and 10 and 50 wt pct H2S04 at temperatures from 50° to 90° C for 300 days. Linear expansions ranged from a low of -0.02 pct for the silica to a high of 0.45 pct for the red shale. A general ranking of the volume expansion of the materials tested, (from high to low), is as follows: high-porosity red shale A and fireclay B » low-porosity red shale B and fireclay A > silicon carbide and silica. A general ranking (largest to smallest) of the effect of exposure environments is HCl > H2S04, HN03 > H20. An autoclave test method was evaluated. Data obtained from 8-to 24-h exposures were compared with data obtained from the 300-day exposures. The relative expansion trends were similar, indicating that this method could be used as an accelerated test.

Jan 1, 1988

By W. T. Wertman

A research program to aid development of better petroleum-recovery technology is in progress at the Appalachian Experiment Station, Bureau of Mines, Morgantown, W. Va. The work is part of the overall effort of the Federal Bureau of Mines to effect true conservation of the Nation's natural resources. Knowledge of the magnitude of the interstitial water content of oil-bearing formations is important to petroleum-reservoir engineers because of the influence of water on fluid flow during oil production and because of the significance of water volume in oil-reserve evaluation. Such information on Appalachian oil-bearing formations is needed to aid in planning secondary oil-recovery projects. Generally, the interstitial water content of oil sands can be estimated by one or more of the following methods: Analysis of cores obtained with oil-base drilling fluid, electric logging, restored-state or capillary-pressure tests, centrifuge tests, evaporation tests, or mercury-injection tests.

Jan 1, 1959

By Joe N. Magee

As part of the important program of promoting conservation and efficient utilization of petroleum, Bureau of Mines engineers are making studies of secondary oil-recovery projects throughout the United states and publishing reports setting forth the pertinent facts so that others may profit by the experience gained. This report presents the results of a study by engineers of the Bureau of Mines, stationed at Franklin, Pa., of secondary oil recovery in a part of the Cabin Creek field, Kanawha and Boone Counties, W. Va., where natural gas is injected into the reservoir to stimulate oil production. Most oil produced in the Appalachian region at present is obtained from stripper fields in which almost all natural energy has been dissipated. Secondary-recovery methods are used extensively in many oil-producing areas of New York, Pennsylvania, West Virginia, Ohio, and Kentucky for recovering oil not produced by primary-production methods. The part of the Cabin Creek field reported in this study is shown in figure 1 and has been designated by the operator as project 4. In 1944 the developed area of the entire field was approximately 4,200 acres, and the area of project 4 was about 600 acres. In the developed area of the project the oil reservoir is in the Berea sandstone and occurs at 2,914 to 3,410 feet.

Jan 1, 1952

By Edward E. Johnson

The principal purpose of this study was the development of an engineering and economic model of a hypothetical large-scale open pit gold mining operation. The guiding concept in developing the model was the idea that, through study of a number of such models, it would be possible to evaluate a mineral property and to make reasonable estimates of the benefits to be derived from research in mining and metallurgy. The model by use of a computer is able to produce results easily and quickly when cost factors are varied. Cost factors may be varied as a result of assumptions of improved technology or of assumptions of assuming different approaches or methods to accomplish a particular segment of the mining or processing operation. The discounted cash flow rate of return was used to measure the effect of changes in costs or expected revenue. In this study, assumptions based on past processing practices were made in an effort to reduce costs of processing the ore These assumptions were: (1) Eliminating the low-grade cyanide circuit; (2) reducing the quantity of material to be processed by screening after crushing; and (3) using a combination of assumptions (1) and (2). All three assumptions resulted in reduced capital investment and operating cost that caused substantial increases in the rate of return.

Jan 1, 1968

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current mining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for dragline reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By Francis X. Cannaday

The Bureau of Mines developed equipment to measure the sonic velocity of pulses transmitted through rock samples varying in size from laboratory specimens to mine pillars in place. Pulses are produced by electronically excited piezoelectric ceramic transducers. Special equipment components were developed by Bureau facilities; other components are commercially available. The technique permits a nondestructive, repetitive, stable, shaped pulse to be used in place of explosive caps or hammer blows. Longitudinal wave travel time measurements were taken on an oscilloscope screen; transverse wave measurements were taken under special field conditions. Results were consistently repeatable within the accuracy of the oscilloscopes utilized.

Jan 1, 1966

By E. S. Leaver

Experiments dealing with the dissolution of silver by cyanide from various silver minerals-were reported, several years ago.4/ This work showed that the silver in some silver minerals is completely and readily soluble in cyanide solution, whereas other silver minerals must be given special treatment before or during cyanidation to obtain much dissolution of the silver by cyanide. Flotation as a method for treating silver ores has not been studied much, except in the case of base-metal ores carrying silver, Particularly lead-silver ores. However, many mills now are concentrating gold ores by flotation, and when such ores also contain silver the recovery of the silver by flotation is of considerable importance. Moreover, many mines contain ore in which silver is the principal valuable constituent. Some of these ores are amenable to cyanidation, but the cost of a cyanide plant may be prohibitive because of limited ore bodies or other factors. In such instances the successful application of flotation would mean that the property could be operated.

Jan 1, 1939