Search Documents

By R. V. Ramani

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a mine located in Illinois using bucket wheel excavator (BWE) and a stripping shovel in tandem for overburden removal is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and scheduling problems and to generate and analyze alternatives for increased production. On the basis of the simulations it was concluded that the maximum productive capacity of the system in raw coal was around 3000 tons per shift. At this production level, the equipment combination and availability also satisfy the match requirements for the stripping shovel and the BWE, and the overburden and coal removal systems. Several alternatives requiring new equipment are proposed and analyzed for increasing production. However, no economic analyses of these proposals were done.

Jan 1, 1977

By R. V. Rahfuse

Noncaking 0- by 2 -inch subbituminous coal from New Mexico was gasified with air and steam at 205 prig using a stirred-bed producer to determine coal losses by entrainment in the gas for this low-sulfur, high-ash coal which contained 20 percent particles smaller than 1/16-inch sieve size. The use of fine-sized coal has particular importance because most production from mechanized mines is smaller than 2-inch size. This initial attempt showed technical feasibility for gasifying New Mexico subbituminous coal containing small-sized particles in fixed-bed producers without excessive coal loss by entrainment. Dust loss averaged about 2 percent of moisture-free coal, most of which was recovered from the gas. Ash clinkering was controlled by adding 1,010 lb/hr steam to reduce tempera¬tures in the combustion zone. Yield of low-Btu fuel gas, 150 Btu per scf, dry, amounted to 69,800 scfh from 1,490 lb/hr coal (as received) and 3,450 lb/hr air (dry).

Jan 1, 1974

By E. R. Palowitch

This report stems from a study by the Bureau of Mines of the possibility of reducing coal filter-cake moisture by applying radiant heat directly to the filter cake while under vacuum during the drying phase of the filter cycle. One disk of a 4-foot-diameter vacuum filter was equipped with gas-fired radiant-heat generators and the effect of radiant heating on the moisture content of a variety of filter cakes was studied. The results of this investigation show that this process can best be described as a filter aid capable of increasing the effectiveness of conventional filtration approximately 6 percentage points of moisture. The operating cost of removing water by this method is somewhat lower than the average operating cost of thermal drying and is considerably cheaper when the total cost is considered. Removal of water from coal that has been wet-cleaned is an important part of the overall coal preparation process. Water is a contaminant, and it is foolish to wash coal to reduce its ash content and add inert water in the process. In some instances the removal of water is actually more important than the removal of ash-forming minerals; its weight adds to the cost of transportation, and its evaporation during burning or carbonizing absorbs useful heat. Fine coal that contains more than about 10 percent moisture is notoriously difficult to handle. A problem thus exists for which there are sound practical and economic reasons to seek a solution.

Jan 1, 1961

By Charles L. Harness

Magnesia (MgO) has a variety of uses, and it has become increasingly important as a war material because of the imperative demand for refractories to line metallurgical furnaces, and because magnesia is used to make the in aircraft and other implements of warfare. Magnesia occurs as an integral part of nearly 60 minerals, but it is extracted commercially from only a .smaller number, of them. The present commercial sources are magnesite, brucite, dolomite, raw sea water, sea water bitterns, and well brines. Magnesia Raw Materials Magnesite magnesium, carbonate MgCO3, theoretically contains 47.8 percent MgO and 52.2 percent CO2. There are two varieties of magnesite, crystalline and cryptocrystalline (dense or amorphous). The latter type, though, not so plentiful as the former, is generally purer. It resembles unglazed write pottery in texture, whereas the crystalline variety is generally dark and granular, though the color may vary. The principal domestic deposits, of crystalline magnesite are near Chewelah, Stevens County, Wash. (which has supplied most of the magnesite mined in the United States), in the Gabbs Valley area of Nevada (near Luning); and in Llano County, Tex. Crypto-crystalline magnesite occurs principally in California. Magnesite occurrences have also been reported in several other States, including New Mexico, New York, New Jersey, Pennsylvania, Massachusetts, Vermont, and Maryland, but these deposits have not been developed commercially.

Jan 1, 1943

By C. O. Hawk

Distillable oils derived from coal were desulfurized and hydrogenated at 2,500 psig in a two-step vapor-phase catalytic operation to give a product rich in saturated cyclic hydrocarbons. The first step was mainly a desulfurization at 400 C, the second a saturation at 300 C. One of the oils used as feed stock was from low-temperature carbonization of a bituminous coal, the other was from the liquid-phase hydrogenation of coal in the Bureau's pilot plant. The product from the saturation step was distilled to remove the light ends and high-boiling residue and to recover a fraction having acceptable properties with respect to heating value, density, freezing point, viscosity, and boiling range according to specifications suggested by the Air Force for ultra-high-speed aircraft fuel. Quantities of the fuel fraction available were too small for the thermal stability test approved by the Air Force. The experiments, performed on laboratory scale, comprised mostly a study of the effect of varying the oil feed rate (at constant oil-to-hydrogen ratio) on the yield of the desired fuel fraction. The yield of the fuel fraction made from low-temperature carbonization oil was a little more than 1 percent of the weight of coal carbonized; that from coal-hydrogenation oil was about 12 percent of the weight of coal hydrogenated. A few attempts to do both desulfurization and saturation in one operation with sulfur resistant catalysts, developed for vapor-phase hydrogenation or hydroforming, were unsuccessful. By leaving the low-boiling ends in both feed stocks to desulfurization, another product was obtained: a low-sulfur aromatic cut boiling below 200 C. This material would be suitable as a solvent or a chemical raw material.

Jan 1, 1965

By W. L. Hunter

This report describes results of beneficiation and smelting studies conducted by the Federal Bureau of Mines on chromite samples from the Emma Belle and Seiad Creek prospects in the Seiad Creek area, northern California. Samples were chosen from this area because the ore is typical of disseminated types that represent a sizable domestic reserve. The two samples were similar in composition, and both responded in like manner to gravity beneficiation. As the ore was banded, considerable coarse gangue was rejected in laboratory sink-float from a minus-3/4-inch, plus-6-mesh fraction without excessive chromium loss at a medium density of 3.32. An average of 85.6 percent of the chromium was recovered in the sink product, which analyzed 35 percent chromic oxide (Cr203). Tabling yielded concentrates containing 49 percent or more Cr203; however, recoveries, ranged from only 33 to 45 percent. A combination of tabling and electrostatic separation of the table middlings showed that the chromium recovery could be increased to about 73 percent; the composite concentrate averaged 53 percent Cr203.

Jan 1, 1960

By I. S. Solet

This study, of the liquidus temperatures and densities of molten alloys of zinc and aluminum was made as part of a broader investigation on refining of scrap aluminum. One of the methods of refining involves the separation of liquid and solid phases by gravity segregation and by filtration. More accurate data were required on the liquidus temperatures and the densities of molten' mixtures of the metals than were available in the technical literature. New data on the liquidus curve were obtained by thermal analysis. The new temperatures are, for the most part) somewhat higher than those reported previously by other investigators. The density of molten mixtures of zinc and aluminum were found to be less than would be calculated by assuming that the two metals occupy the same respective molal volumes in solution as they do as pure metals.

Jan 1, 1949

By J. E. Tiffany, N. A. Tolch

The Pittsburgh Experiment Station has made a survey of the properties and characteristics of the brands of fuse manufactured in the United States ; 25 samples were procured from 4 manufacturers representing the different brands offered on the market when the investigation was begun . It is believed that the field was completely covered except for special fuse made to order for a particular job .

Jun 1, 1934

By N. E. Hanna

As part of a program for improving, the safety of permissible explosives, the Federal Bureau of Mines has undertaken an investigation to establish the ability of sodium chloride to reduce the incendivity of permissible explosives to firedamp atmospheres. A motivating influence for this investigation has been the comparatively extensive experience of British and other European investigators, who used sodium chloride as a component of their permitted explosives (1, 5, 6 7).5/ In the United States research and development work of this type has been less extensive, although sodium chloride has been added to permissible explosives as a cooling agent (9) for many years. The results of the first phase of this investigation were presented in a previous paper (8), which established that adding up to 10 percent sodium chloride to permissible explosives reduces the likelihood of ignition of firedamp in the gallery test; however, the results were somewhat inconsistent, and the conclusions were qualified. Accordingly, the investigation was continued with a study of the effect of added sodium chloride as a function of the quantity added and of the particle size of the salt.

Jan 1, 1960

By John M. Gomes

Two molten salt systems were evaluated as electrolytes for the repetitive recovery of tungsten from tungsten oxide (W03) made by calcining commercial-grade ammonium paratungstate. Using a sodium chloride-sodium fluoride-potassium aluminum tetrafluoride electrolyte at 800° C, 1 pound of 99.8 percent tungsten was recovered for each 2.7 kilowatt-hours of energy consumed. The metal contained 1,100 ppm carbon, was in dendritic masses of spherical grains, and had an apparent bulk density of 5.41 g/cm3. T ngsten of 99.9 percent purity was won from a sodium pyrophosphate-sodium tetraborate-sodium chloride electrolyte at 1,000° C; 6.0 kilowatt-hours of energy was consumed for each pound of metal recovered. The metal contained 120 ppm carbon, was in dendritic masses of hexagonal acicular crystals, and had an apparent bulk density of 7.25 g/cm . Each metallic impurity--aluminum, calcium, copper, iron, nickel, and silicon--in the two tungsten products was 16 ppm or less.

Jan 1, 1966

By Arnold B. Hubbard

This report presents a hydrogenolysis study undertaken to obtain information on the constitution of the kerogen or organic material in Colorado oil shale and to determine some of the properties of the hydrogenolysis products. The high yield of hydrogenolysis products was separated, so far as possible, into type compounds; a number were identified. The results thus obtained were used as a basis for proposing the possible existence of certain structures in kerogen. To the authors' knowledge, few or no hydrogenolysis studies have been made of Colorado oil-shale kerogen by others. However, this method has been used in studying the constitution of coal. In general, the coal studies involved treating pulverized coal at different temperatures and hydrogen pressures with different catalysts. In some instances different solvents were used during the treatments.

Jan 1, 1959

By Robert H. King

An analysis of low-voltage shielded trailing cables is performed to develop a method for calculating the differences in operating costs between shielded and non-shielded cables. Two types of shield constructions are considered (SH-C and SH-D) for the three major underground coal mining methods. Data from laboratory and in-mine testing are presented in addition to an analysis of safety benefits. Recommendations for further investigations are proposed. Example calculations with sensitivity analyses are presented. Recommendations for further investigation include costs impact considerations.

Jan 1, 1980

By David Schlain

A small alumina reduction cell with a graphite crucible and boron nitride liner was developed by the Bureau of Mines as the initial phase of a study of the reactions which occur in the reduction of alumina by the Hall-Heroult process. Operating conditions in the cell such as temperature, time, current density, electrolyte composition, and electrode materials may be varied easily. Aluminum was produced in the cell at a current efficiency of about 75 percent and a cell voltage of 2.7 volts. Although the data are not wholly conclusive, the operation of the cell did not appear to be greatly affected by large changes in temperature, electrode spacing, current density, and alumina concentration in the electrolyte.

Jan 1, 1963

By Lawrence G. Houk

Monazite sand is the only commercial source of cerium, other rare-earth metals and thorium. Although used in rather small quantities, it is essential to many industries. The United Unites is entirely dependent upon British India and Brazil for its supplies. Monazite sand or sand imported under the tariff classification for monazite was shipped to the United States in greater quantities, in 1940 than ever before. About 75 percent of our imports was from British India and most of the remainder from Brazil. If need be, Brazilian production can be expanded to supply all of our essential requirements, and the theater of war expands in the Pacific Brazil may supersede India as the principal source. PHYSICAL PROPERTIES The mineral monazite is generally honey yellow or may vary from greenish yellow to clove brown. The grains are small and resinous in luster, and range from subtranslucent to opaque. The specific gravity varies

Jan 1, 1943

By V. T. Dow

In April 1957 the Bureau of Mines instituted a reconnaissance of titanium-and zirconium-bearing heavy sandstone deposits in the Four-State area of Utah, Wyoming, New Mexico, and Colorado. This report summarizes the study. Eighty-two deposits or groups of deposits, containing an estimated 27,920,000 tons of titaniferous sandstone, were examined in the Four-State area; 16 in southern Utah, 19 in Wyoming, 33 in New Mexico, and 14 in southwestern Colorado. The 16 deposits examined in Utah contain an estimated 1,043,000 tons with an average grade of 17.98 percent TiO2, 5.67 percent ZrO2, 20.98 percent Fe, and 0.09 percent equivalent Th02. The 19 deposits investigated in Wyoming are estimated to contain 21,873,000 tons of titaniferous sandstone having a weighted grade of 5.22 percent 702, 0.55 percent ZrO2, 24.8 percent Fe, and 0.01 percent equivalent Th02.

Jan 1, 1961

By L. F. Heising

Ten composite samples of Mesabi Range nonmagnetic taconite from the Hibbing, Minn., area were evaluated by flotation and by reduction roasting-magnetic separation to determine their potential as a future source of iron are. Only one of the composites yielded concentrates that could be considered marketable, using as a criterion a 10-to-1 iron-to-silica ratio. Cursory petrographic examinations of all 10 composited samples and a detailed mineralogical study on 1 sample suggest that unfavorable mineralogical associations between iron and gangue minerals are responsible for their poor beneficiation characteristics.

Jan 1, 1967

By C. J. Walker, J. S. Miller

This work was done in an attempt to find a simple solution to the problem of simultaneously changing terminal rate and terminal pressure under conditions of unsteady - state flow in porous media . Although the original aim was not realized , a method for encasing a sandstone core that would permit high - pressure ( 200 to 980 psi ) flow tests and the use of electronic equipment to measure pressures at points along the core during unsteady - state gas depletion was found to be feasible . The sandstone core used in this study was from the Bandera formation of Pennsylvanian age , Redfield , Kans . The core , cylindrical in shape with a 3.5 - inch diameter and 6- foot length , had a porosity of 15 percent and a permeability of 9 millidarcys .

Jan 1, 1963

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casing-heads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil. into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casingheads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By B. M. Bird

For several years the U.S. Bureau of Mines and the University of Washington have been cooperating, in a study of coal tabling. The first pert of the work consisted of experiments using, one of the commercial-sized coal washing tables in the laboratories of the College of Mine. As an outgrowth of this work, hindered-settling classification has been successfully applied in the tabling of coal4, and several important improvements, mainly in the riffling, have been made in the table itself. Both of these developments have resulted in increasing the rapacity and efficiency of the coal-washing table. In order to facilitate further progress in this work an investigation has been undertaken to throw more light on the mechanism of table separation. The final separation of a table is obviously the resultant of several operations; namely, stratification, removal of the top strata or parts of them as washed coal by the cross-flowing water, and removal of the bottom strata or parts of

Jan 1, 1929