Search Documents

By S. H. Ash

NO MORE important question has come before the coal-mining industry in many places, especially in the anthracite region of Pennsylvania, than prevention of stream pollution by mine drainage. Available information on acid mine drainage in the anthracite region of Pennsylvania indicates that a pollution problem must be solved in any program of anthracite mine drainage. The major problem concerns satisfactory disposal of the daily average mine-water discharge of 327,000 gallons per minute (g. p. m.), or 472 million gallons per day (g. p. d.), containing a free-acid load of 431 tons or a total acid load of 934 tons a clay as H2S04. This report indicates the scope of the problem and gives some suggestions concerning its solution.

Jan 1, 1951

By Sarkis G. Ampian

Extraction of alumina was correlated with the sinter and leach products from the lime soda sinter process for anorthosite. The effect of composition and grain size of reactants, time and temperature of sintering, and techniques of sample preparation were investigated. Greater than 90 percent Al2O3 extractions were obtained from dry-mixed minus 200-mesh anorthosite sinter mixes having mole ratios of CaO/SiO2 = 1.8 and Na2O/Al2O3 = 0.8. These sinter mixes were briquetted at 15,000 psi and fired between 1,200° C and 1,320° C for 20 to 60 minutes. The sinter phases that contribute to low alumina recovery were determined by X-ray diffractometry, optical microscopy, and electron probe X-ray spectrography. The mechanism of the sintering reaction was investigated by high-temperature X-ray diffractometry. The contrast in the lime soda sinter process for clays and for anorthosites are discussed. Explanations and suggested solutions are presented for problems such as gelation and variable alumina recovery encountered by previous investigations.

Jan 1, 1967

By M. J. Kirwan

[There have been large increases in the oil production and casing-head gas production of certain wells on the Quinn dome (northern part of the Lyons-Quinn field of Oklahoma) caused by large volumes of gas under high pressure entering Vie productive oil sand, The oil production of sore of the leases in this part of the field temporarily increased over 100 per cent within a few days after gas entered the oil sand among the leases that had the greatest increases in oil production wore those on which no gas wells were drilled but which were located up-elope on the structure in reference to gas wells on adjoining properties. It is conservatively estimated that 1,444,000,000, cubic feet of gas entered the productive oil sand and, up to January 1, 1924, caused an increase of about 950,000 barrels of oil from this sand. The casing-held gas volumes of a number of wells producing between 25,000 and 75,000 cubic feet of gas per day increased to several hundred thousand cubic feet and a few walls increased to nearly two million cubic feet per day after extraneous gas entered the oil sand from which the wells were producing.]

Jan 1, 1924

By A. Visnapuu

The Bureau of Mines has upgraded high-iron domestic chromite concentrates by a carbonyl process. The upgraded chromite concentrates show as much as 10 wt pct higher Cr203 content and up to a threefold in-crease in the Cr:Fe ratio, compared with the starting concentrates. The high-iron chromites were first reduced to convert the iron oxides to the metal, and then treated with CO at elevated pressures and low temperatures to convert part of the metallic iron fraction to iron pentacarbonyl. Carbonylation was accelerated by the addition of H2S in small quantities. The iron pentacarbonyl was extricated from the con-centrate in the pressure reactor during carbonylation by a CO sweep through a pressure-reducing valve and passed through a decomposer at atmospheric pressure to convert it back to iron metal and CO. CO pres-sure, temperature, promoter trends, and other factors enhancing iron pentacarbonyl formation are presented.

Jan 1, 1985

By W. H. Oppelt

The continuous gasification of lignite in an externally heated alloy-steel re-tort was investigated by the Bureau of Mines, Grand Forks, N. Dak., from 1945 to 1951. The main objective of the long-term experimental program was to obtain data on the mechanical performance of this type of gasification retort, particularly the alloy-steel heat-transfer surface of the retort, when operated on large pilot-plant scale. At the same time, extensive experimental data were obtained concerning the effect of process variables and the effect of a limited number of design modifications on gasifier performance. In the period covered by this progress report 4 pilot-plant runs totaling 2,879 hours of operation were completed with the rolled-plate, 310-alloy reaction tube. Over 30 million cubic feet of gas, having H2-CO ratios from 2.1 to 4.4, was made by the partial gasification of 636 tons of 1-1/2-by 3/8-inch natural lignite. Rates of gas generation were from 8,200 to 14,300 cubic feet per hour. Three of the four runs were carried out with the lowered gas offtake or continuous-annulus design modification of the gasification retort. In the final run of the series, gasification of lignite from seven different mines in North Dakota and Saskatchewan, Canada, was investigated at similar combustion-space temperatures and lignite and steam feed rates.

Jan 1, 1955

By Oliver Bowles

Accidental explosions in coal mines are due to various causes, but many of them can be directly attributed to coal dust; others that probably in no way depend on dust as a primary cause are propagated, greatly intensified, and made more disastrous by the presence of coal dust. The fact that coal dust in a bituminous mine will explode as a result of a fire-damp explosion has been generally accepted for many years, but the belief has also been held by many that coal dust is not in itself dangerous when unmixed with an explosive gas. Therefore, in past years little attention was given to dust in mines free from fire damp, and many disastrous explosions have resulted from lack of knowledge of the danger from coal dust. In the explosives gallery and experimental mine of the Bureau of Mines experiment station, Pittsburgh, Pa., it has been proved repeatedly and conclusively that coal dust will explode violently when no inflammable gas is present. PROPAGATION OF DUST EXPLOSIONS A coal-dust explosion is an extremely rapid burning or combustion of the coal particles. Their burning consists essentially of the combination of the hydrocarbons in the coal with the oxygen of the air, a process that generates heat and flame and produces hot gases and water vapor. These gases and vapors have a volume many times that of the original coal particles; thus they exert an outward motion and pressure which constitute the explosive wave. When fine particles of coal are suspended in the air, each particle is surrounded by the oxygen of the air, and thus is well placed to oxidize or burn rapidly whenever the temperature is high enough. If some particles are ignited from any cause they will fire others, and the combustion will extend from particle to particle with extreme rapidity wherever enough coal dust of sufficient purity is present.

Jan 1, 1925

By S. H. Ash

THE INVESTIGATION of barrier pillars in the Western Middle field is part of the comprehensive study of the mine-water problem in the anthra¬cite region of Pennsylvania by the Federal Bureau of Mines (1, 2, 5, 6, 7, 8,9,10,11,1,2,15,16).8 The Western Middle field is in Schuylkill, Columbia, and Northumberland Counties in eastern Pennsylvania. It has an area of 120 square miles, is 42 miles long from Delano on the east to Trevorton on the west, and is 2 to 5 miles wide. In the Western Middle field are 58 underground water pools containing 38 billion gallons of water (5). Some of the pools overflow to the surface, and the water from others seeps into adjacent mines through permeable barrier pillars separating them from abandoned mines. Several active mines are interconnected to workings in abandoned mines, which are partly filled with water. These mines are separated by barrier pillars that are considered effective only below the altitude of the connections. In some abandoned mines, pumping stations maintain the water at altitudes where the hydrostatic pressure against the barrier pillars is not excessive and does not endanger adjacent active mines. If water in these abandoned mines is allowed to rise to where it can overflow into the active mines, it must be pumped from the active mines at lower altitudes; this materially increases the cost of pumping. It is estimated that from 1944 to 1948 approximately 30 percent of the water pumped to the surface was from abandoned mines.

Jan 1, 1953

By A. S. Swanson

The Babb fault vein in Crittenden and Livingston Counties, Ky. (fig. 1), is one of an extensive series of such veins in the Western Kentucky and Southern Illinois fluorspar district. First operated in 1904, the production to May 1, 1944, was estimated at 143,000 tons of fluorite ore. There are five mines (fig. 2) on the Babb fault zone - Guill ,Kentucky Babb, Delhi-Babb, Eagle-Babb and Howard-Barnes. The Bureau of Mines developed four of these properties by core drilling from July 9, 1943, to May 1, 1944. During that period a total of 8,177.8 feet of diamond drilling was completed in 28 holes.

Jan 1, 1950

By K. A. Fowler, L. W. Higley

Steels with an alloying addition of depleted uranium were studied to develop successful melting , casting , and fabricating methods ; to obtain data on mechanical properties ; and to determine the effects of this alloying element . Uranium in amounts up to 1.5 percent was added to steel - base compositions containing approximately 0.5 percent carbon , 2 percent nickel , 0.25 to 2.0 percent silicon , and 0.75 percent manganese in both vacuum- melted and air -melted heats . Radiation levels were monitored for all operations . Bureau of Mines research at the Rolla Metallurgy Research Center showed that uranium additions did not increase tensile strength ; that hot - shortness occurred during forging above 1,090 ° C because of the presence of a low melting point constituent of a eutectic type ; and although a measurable amount of radioactive contamination resulted from processing , the quantity was never large enough to require the work area to be identified as a radiation area .

Jan 1, 1964

By David A. Monaghan

This report describes instrumentation which is part of a system for extinguishing mine fires by pumping material through surface boreholes in order to seal off all underground passageways leading to the fire area. Major instrumentation systems include a closed circuit television probing system and an acoustic seal checking system. The latter consists of a speaker probe, a receiver probe and related signal processing equipment. All probes can be winch-deployed down a 6-inch diameter borehole. The CCTV unit can be rotated 360 degrees in the horizontal plane, and contains sufficient lighting to reliably assay conditions for sealing or rescue within a 200 foot radius. The acoustic seal checker monitors the completion of a seal as it progresses by use of probes lowered through boreholes on either side of the seal.

Jan 1, 1977

By Edwin B. Cook

Studies of flame and combustion phenomena at the Bureau of Mines have been facilitated by computer evaluation of the thermodynamic properties of gases formed by constant-pressure burning.4 5 This report is the sixth of a series6-10 presenting results of such calculations; it deals also with constant-volume deuterium-air flames.

Jan 1, 1961

By Haskiel R. Shell

Methods of chemical analysis of clays for the following constituents are presented: moisture, ignition loss Fe2O3, TiO2, P2O5, CaO, MgO, Na2O, K2O, total. carbon, carbonate carbon total sulfur, soluble salts, and soluble sulfate. In these procedures the attainment of accuracy has been the primary consideration sample was taken to insure accuracy, with ordinary precautions. The procedures may therefore be somewhat somewhat and will not be suited for routine work on samples for which the approximate analysis is already known and in which the need for accuracy is not very exacting. However, the method shod be as a set of detailed directions, that have been tested and shown to yield accurate results with clays and other aluminum silicate minerals. Among these minerals are clays of all types, bentonite bauxite, shale, brick; soil, calcined refractory, and sand. Although some of the methods are Unusual, no particular claim is laid to originality. The material was drawn frail many sources, put together and tested.

Jan 1, 1949

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine would be drilled. The geologic formations encountered in this hole are discussed. Correlation of the geologic horizons encountered in this hole with those encountered in nearby drill holes was accomplished by the use of geophysical logs. Data on the geophysical interpretations are provided. The anticipated geotechnical characteristics of the geologic units encountered in Pilot Hole "X" are described.

Jan 1, 1977

By Ross. C. Barkley

A computer program has been written to simulate ground vibrations induced by multiple-hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosives charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g. velocity, attenuation, pulse), or by backcalculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties are backcalculating individual pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shown to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included and additional verifications with field results are required.

Jan 1, 1983

By Glenn A. Shirey

The objective of this contract as to prepare a detailed, readily usable handbook on dust control techniques for longwall mining operations. Information was gathered from available literature, and through contacts with industry and government personnel. The handbook describes those methods of dust control applicable to today's longwall mining systems, and contains sufficient design elements to assist operators with problems in testing or implementing new control procedures. Complete reference lists are presented at the end of each chapter to direct the reader to additional information.

Jan 1, 1985

By R. L. Brown

This report, the seventeenth in an annual series, summarizes Bureau of Mines research and technologic work on coal and related investigations for July 1, 1951, to July 1, 1952. It 1s based largely on publications issued during the fiscal year, although 10 some instances data are presented that have not been published previously. Footnote references are given to the publications so that further details on the work may be obtained. Bureau of Mines research on the mining, preparation, and utilization of coal is directed toward developing and encouraging safer and more efficient mining practices and preparing and utilizing coals to the best advantage.

Jan 1, 1953

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining Co.'s Granite Mountain shaft. How this insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the lire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest pro¬ducer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By Steven K. Ruggieri

This report describes the use of the sprayfan auxiliary ventilation system for methane and dust control on continuous miner sections to potential users. The sprayfan auxiliary ventilation system is a modified water spray system which directs intake air to and across the front of a continuous miner to prevent build up of methane gas and dust concentrations. This user's manual contains practical information concerning sprayfan: a. Description and capabilities b. Design c. Installation d. Operation e. Maintenance. Underground tests, independent laboratory tests, tests by MSHA, and independent installations by coal producers have confirmed the performance of the sprayfan system. There are currently 150 sprayfan systems in operation in underground coal mines.

Jan 1, 1981

By W. M. McKewan

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. A 2-in-diameter 6x25 fiber core rope was degraded on a bending fatigue machine. This was the first in a series of tests on rope of this construction and size. Baseline testing at the laboratory was reported in an earlier publication. Tensile and nondestructive tests were performed on samples of the rope to determine the relationship between rope deterioration and rope breaking strength. The tests indicated that as a wire rope nears the end of its useful life, deterioration and the consequent loss of rope strength increase at an accelerated rate.

Jan 1, 2010