Search Documents

By Dennis A. Clark, Richard E. Calvin

As the scarcity of mineral resources increase and subsurface mining activities expand along with simultaneous surface mining in coal, industrial minerals and rocks, along with metals, the need to insure safe conditions is paramount.

Jan 1, 1981

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1991

By B Mohanty

Full-face blasting rounds have been used to excavate a 4.6-mdiameter shaft at Atomic Energy of Canada Limited's Underground Research Laboratory near Pinawa, Manitoba. Both standard pyrotechnic delay detonators and the newly developed electronic delay detonators (EDD) were used on the project. The full-face blasting technique, employing 89-mm-diameter relief holes and 38-mm diameter blast holes, NG-based explosives, and the regular long period delay detonators, has been standard practice at the site, giving excellent wall control and fragmentation results. The comparison blasts using pyrotechnic detonators and EDDs were carried out to test the operational logistics, timing accuracy and blast results obtained with the latter. The long period pyrotechnic delays ranged from O to 18, with the nominal delay varying between 350 ms and 800 ms. The EDD blasts used the same number of periods, with the respective delay interval between successive periods set precisely at 190 ms and 210 ms for the two blasts. Based on a broad range of critically assessed parameters, the EDD blast results proved to be signficantly superior to those obtained with regular pyrotechnic detonators. The results have been analyzed in detail and the relative merits of the two delay systems have been determined. Alternative designs to derive maximum benefits from EDDs in shaft and tunnel blasts have also been suggested.

Jan 1, 1990

By Charles H. Dowding, Catherine T. Aimone

Rock particle sizes were measured at fourteen steep-slope Appalachian coal mines during production blasting. The distribution of rock sizes shows the effects of inter-hole timing, sequence of hole initiation, as well as charge distribution within each shot. Blast design parameters were selected to: (1) minimize displacement of broken rock conforming to throw control required of mining methods, (2) minimize seismic effects, and (3) create breakage at a cost economical to mining operations.

Jan 1, 1983

By Mark Roberts

Automation, data analytics and optimisation are key trends in the mining industry. Doing more, and better, while expending less resources targets KPIs around efficiency and productivity. With the explosion of data, the next step is to develop an optimal level of processes and systems to harness this data to support value-in use decisions. Typically, significant amounts of resources and effort are invested to develop realistic simulation models. However, models are frequently not integrated with existing systems, and therefore are underutilised. When we consider the specialised process of blasting, integration with upstream and downstream processes is a significant driver to realise sustained improvements and value. The application of genetic algorithms and cloud computing to solving complex mining problems has advanced over the last 15 years, in particular with mine scheduling. Genetic algorithms are unique in that they support true multi-objective optimisation, utilising population-based methods to present trade-offs between multiple solutions. Secure in-cloud processing speeds up the processing, with results delivered in timeframes that are not feasible with desktop computing.

Feb 6, 2023

By Tapan Goswami, Stephen Jeric, Geoff Brent

Highwall failures in large deep open cut mines have very significant safety and commercial implications. There are many factors influencing the stability of highwalls. The major influence is the interaction of the local geology with the shape of the pit wall. This factor is in the realm of the geotechnical engineer and is beyond the control of the blasting engineer. However, a secondary influence is the blastinduced damage to the wall. In most open cut metal mines the blasting strategy to control this damage involves the use of separate production and trim blasts bounded by presplits at the final wall.

Jan 1, 2011

By Greg Wyartt

"At an Australian iron ore open-cut mine, 129 separate blast patterns (consisting of 38.5 million tonnes /42.4 million US tons, equaling 28% of annual blasted tonnes) were initiated using electronic detonators. 87 patterns were designed as per site methodology using ‘vectorial’ initiation timing sequences (blast direction and relief specified only), while the remaining 42 patterns were designed with interactive initiation timing sequences - hole by hole sequencing based on the measured site specific primary shock wave (P-wave) velocity and distance between blast-holes. The intention of this project was primarily to reduce material size presented to the crushing circuit, and also to determine if productivity benefits could be obtained by the use of interactive timing."

Jan 1, 2017

By A. Torrance

A better understanding of the detonation performance of an explosive charge can be gained by directly measuring pressure, temperature and velocity of detonation (VOD). This is particularly important with commercial explosives because their performance is directly influenced by the degree of confinement given by the borehole diameter and the surrounding rock mass. A project funded by the Australian Coal Association Research Program (ACARP) was initiated in early 2009 with the view to design and build cost effective prototype instrumentation to measure the relative differences in detonation pressures and temperatures of commercial mining explosives. The project’s primary focus was on low density explosives. Low density (also referred to as low shock) explosives have been available in various forms for nearly 20 years. Identifying the pressure release patterns of both conventional and low density explosives under different geotechnical conditions should provide the necessary information to both validate detonation codes and better define input parameters for breakage and fragmentation models. This paper gives a general description of the prototype instrumentation developed and reports on the results obtained to date in testing the proposed instrumentation in laboratory scale conditions.

Jan 1, 2011

By Gregory B. Poole

Data collected with 16K sampling at a variety of blasting sites (construction, quarry, trench, mine) and monitoring locations was analyzed to effectively show the 16 different 1K readings all based on the microsecond that the unit went into monitoring.

Feb 1, 2020

By Stephen Mansfield, Nathan West, El Khalil Seyed

In October 2017, a multi-bench failure occurred in the east wall of the Guelb Moghrein copper and gold mine in Mauritania. The failure extended 100 m (328 ft) vertically and horizontally and resulted in the sterilisation of ore, but no equipment or personnel were put in danger. The remediation plan successfully removed the failed material and the cutback resumed to a modified pit design, leaving ore reserves behind. In 2021 after completion of mining in another part of the pit, a plan was formulated to develop a narrow cutback behind the failed wall and recover the sterilised ore. Infill drilling defined a resource of approximately 2.9 Mtonne (3.2 Mton) of ore at 0.78% Cu and 0.67 g/t Au at a strip ratio of 5.5:1. The high strip ratio meant that it was necessary to mine thirteen benches of waste, or 156 m (512 ft) vertically, over a two-year period before reaching the first ore, with the cutback only being economically viable if all ore could be depleted at the end of the third year. The high economic risk of the project required a holistic approach to mitigate the risk of another wall failure, by addressing the following areas: 1. Pit Design: with help from an external Geotechnical Consultant, the pit design was optimised to include increased factors of safety, reduced stress points, lower overall slope angles and straight lined walls were replaced with curved walls. 2. Geotechnical Management: the site Geotechnical Superintendent worked closely with an external Geotechnical Consultant to better understand the structural geology. Slope monitoring was improved through an expanded network of prisms, regular in field inspections and the use of a slope monitoring radar. 3. Drill and Blast: new drill and blast designs were developed from first principles, consisting of production, wall control and presplit designs. Blast master polygons and bench development sequences were developed with consideration of the structural geology and the influence of the initiation designs. 4. Mine Operations: improving operational discipline was a critical factor that ensured the accurate execution of drill and blast designs and excavation to bench levels and pit limits. This holistic approach has enabled the safe development of the cutback down to the 936 RL (relative level), two benches below the point at which the previous wall failure occurred. Extraction of ore has occurred from the 960 RL, and due to faster than planned excavation rates, the cutback is expected to be completed ahead of schedule.

Jan 21, 2025

By F. Malek

An extensive blast monitoring program has been carried out to study explosive performance and the effectiveness of blast designs in production blasts in a deep underground mine. Comprehensive monitoring of blasting vibrations through multi-station high-capacity high-frequency accelerometers, and borehole deformation history have been the main tools of such analysis. The mining activity involves relatively unstressed stopes as well as highly stressed stopes. More than 30 production blasts have been monitored, and the respective vibrations from close-range as well as distant seismic stations have been analyzed, and the vibration parameters (amplitude and frequency) have been correlated with explosive charge weight in the holes. It is found that the correlation between blasting rounds and the corresponding vibration amplitudes often have poor correlation for a very significant portion of the blasts. These point to either explosive charge malfunction in those specific blast holes, or inadequate blast design, or the effect of high in-situ stresses, or any combination thereof. This paper analyzes these variables and their effect on the overall blasting operation at the mine.

Jan 1, 2013

By Michael Swisdak, John Tatom

In a quantitative risk assessment (QRA), the ability to accurately model real-world situations is obviously critical. In the end, the model must be able to represent the effects produced by the detonation of the donor and the consequences on the target. The science that goes into such a model must be carefully thought-out and based on as much data as possible.

Jan 1, 2007

By Claude Cunningham

Blasthole pressure is the starting point for many blast design calculations, but the way in which it is usually derived, from measured detonation velocity, indicates that more thought is needed as to its true meaning and implication. The general impression is given that the energy in the hole is defined by VoD, but rarely is this the case. VoD is defined by the energy released in the Detonation Driving Zone between the shock front and the Sonic (or 'CJ') surface, and for commercial explosives it is normal for reaction not to be complete within this zone. Reaction and energy delivery continues behind it, not reflected by VoD. Thus it would be more appropriate to use the theoretical VoD, not the measured VoD, to derive the starting pressure, since this would reflect the energy input of full reaction. In decoupled situations, the derivation of pressure at the blasthole wall using a polynomial decay concept is also of debatable value, and an alternative is offered.

Jan 1, 2006

By Fumihiko Sumiya, Yukio Kato, Yoshikazu Hirosaki

Secluential blasting is one of the most popular methods in blasting. tiowever, it is well known that an emulsion explosive can be dead-pressed by dynamic pressure generated by the previous detonation. It is difficult to gain the expected blasting performance due to tb.e malfunction of explosive caused by deadpressing and shock desensitization. Such malfunction of an explosive is undesirable for safety blasting operation. Voids in the emulsion explosives will considerably affect the performance of explosives such as sensitivity, detonation velocity (DV), pressure-resistance and so on. To clarify the detonability and the performance of precompressed emulsion explosives, the DV was measured. Three types of microballoon or micro bubble ; two types of glass microballoon(GMB), resin microballoon@MB) and chemical gas bubble ; were used as sensitizers for the sample emulsion expiosives. The underwater explosion test was carried out to load dynamic pressure into the sample explosives. The dynamic pressure was generated by the detonation of a donor explosive, and the DV of the sample explosives as acceptor was measured by ionized gap terminals. The dynamic pressure level and initiation interval for the donor and the acceptor were chosen as experimental factors. The detonability was carefully investigated at short initiation intervals taking into consideration the interaction between same delays caused by the deviation of the ignition time of the electric detonators. From these experiments, the following results were obtained ; A) The DV of precompressed emulsion explosives was low compared with that of uncompressed emulsion explosives in all pressure conditions. B) The decrease of DV in the sample explosives sensitized by GMB s was larger than that of DV in the sample explosives sensitized by RMBs or chemical gas bubbles. C) The recovery of the detonability occurred rapidly in the sample explosives sensitized by RMBs and chemical gas bubbles. However, a long period was needed for the recovery of detonability in the sample explosives sensitized by GME! s. It was concluded that the type of microballoon and micro bubble significantly influenced the detonability of precompressed emulsion explosives.

Jan 1, 2002

By K. Hausmann, P. A. Sashin, G. J. Prejean

Misfires caused by unreliable shock tube constructions can have significant cost implications and place field workers at serious risk during remediation. Ionomer materials, used as a subtube in shock tube constructions, provide superior hot tack strength, oil resistance, impact resistance at cold temperatures and excellent thermoformability properties. These are important features for resisting blast-throughs and ensuring blasting reliability in demanding environments, such as open pit mining in harsh environments. Superior hot tack strength, strain hardening, and excellent thermoformability properties of the ionomer materials ensure uniform powder distribution along the shock tube during construction and avoid undesired powder accumulation due to deformation or vibration during use. Oil or chemical resistance is another feature of Ionomers. This allows improved property retention in contact with oils and hence longer sleep times of the shock tube. Another feature of these highly engineered ionomers is superior impact strength at low temperatures. This plays an important role considering the resistance to fly rock impact in open pit mining operations in particular in cold climates.

Jan 1, 2011

By Robert Hopler

SECTION 9.---BORING AND BLASTING.*155. Blasting is the operation of bringing down and detaching from its bed or position masses of material by means of explosives.

Jan 1, 2011

By W. L. Saunders

RBH Note: In the early days of drill & blast tunneling the jobs utilized large crews of drillers and muckers. Advance per round was limited (typically around four feet) but two rounds per 8-hour shift were expected, around the clock. The scene after a shot must have been chaos, with the muckers expected to quickly make space for the drill setup. Makes one wonder how much time was allowed for the smoke and fumes to clear. Note the headgear of the tunnelers.

Jan 1, 2011

By A. Ravi Kumar

A trench is a structure to accommodate fluid carrying pipelines for water, gas, petroleum products etc. Trench serves the purpose to haul the fluids in bulk over long distances safely and economically. Use of pipeline for moving oil and gas was essentially a post World War II development, but now it has acquired its own importance.

Jan 1, 2008

By Gustavo Huerta Valer, Jorge Cárdenas Miranda, Johan Salas Flores

One of the challenges of mining is the optimization of the blasting process, which has an important impact downstream in the processing of crushed ore in the plant, that is why mining companies ensure the results of granulometry obtained from the blasting process through a joint work with companies specialized in the process of loading with explosives.

Feb 6, 2023

By B Mohanty, R Deshaies

Initiation of small diameter explosives by sympathetic shock pressure in water has been investigated under controlled laboratory conditions. Changes either in the geometry of the donor explosive or its point of initiation can alter the essential characteristics (amplitude and duration) of the resulting shock pressure pulse. The pressure signatures from both spherical and cylindrical explosives donors have been studied, in water as well as in various explosive matrices. This paper summarizes the investigations carried out with both 'primed' and 'non-primed' slurry and emulsion explosive matrices with various types of voids. These measurements serve the basis for predicting distances in water for sympathetic initiation for both spherical and linear charges. It is shown that the explosive-detonator system in combination has a far greater probability of initiation due to sympathetic shock pressure than either the explosive or the detonator alone. Various explosive matrices with air bubbles and glass microballoons have been examined and the differing sensitivities to shock pressure explained on the basis of these measurements. It is also concluded that explosives containing air bubbles instead of microballoons would be significantly more prone to sympathetic initiation.

Jan 1, 1992