Search Documents

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

The ever increasing demand for energy and the progressive depletion of crude oil resources, have renewed interest in oil shale as an alternative fuel resource. Weathered oil shale samples were assembled from El-Nakheil phosphate mine in Quseir area, Eastern desert, Egypt. The oil shale samples were prepared and analyzed by XRD (X-ray diffraction), XRF (X-ray fluorescence spectrometry), and optical microscopic techniques. Rock-Eval pyrolysis and total organic carbon were used to study shale hydrocarbon potential. A leaching procedure using inorganic and organic acids was used to selectively dissolve the oil shale associated ash forming minerals. XRD results showed that calcite is the dominant carbonate mineral, whereas primary silicate minerals are quartz and montmorillonite. SEM (Scanning Electron Microscopy) observations indicated that the organic matter is dispersed throughout the rock matrix. The acid soluble fraction upon leaching was determined to be 37.59 and 42.74 wt% by using 5% HCl and 10% HCl, respectively. The TOC was increased from 20.78 to 29.88 and 34.09 wt% by using 5% HCl and 10% HCl, respectively. Keywords: el nakheil oil shale, characterization, xrd, xrf, sem, elemental analysis, proximate analysis, ultimate analysis, thin section, rock eval pyrolysis, acid leaching

Sep 1, 2012

By M. Minagawa, G. Granata, C. Tokoro, T. Kato

"In this work, we studied the mechanochemical activation of chalcopyrite by vertically stirred ball milling (VSBM) to enhance the dissolution of copper. By using x-ray diffraction (XRD) and laser diffraction particle size analysis, we investigated the effect of milling and milling conditions on particle size and phase composition of the chalcopyrite concentrate. To elucidate the efficiency of VSBM towards the mechanochemical activation of chalcopyrite, we also conducted leaching experiments in sulfuric acid-ferric sulfate media. Under all investigated milling conditions, the VSBM determined a dramatic decrease of particle size from over 100 µm of P80% up to about 13 µm. Furthermore, the XRD of the ground chalcopyrite specimens highlighted a partial oxidation of the mineral. In leaching, upon grinding by VSBM, the increase of copper extraction ranged from a minimum of +10% to a maximum of +40%, depending on the grinding conditions. In order to elucidate whether the dissolution enhancement was a consequence of the decreased particle size or of an induced mechanochemical reaction, we performed leaching experiments on activated and non-activated chalcopyrite sample having the same particle size. In addition, we determined the activation energy of leaching before and after vertically stirred ball milling. The leaching results on samples with the same particle size highlighted a greater copper extraction and higher dissolution rates upon mechanochemical activation. Whether performing grinding by VSBM or not, the leaching kinetics was found to be controlled by the chemical reaction on the surface of the chalcopyrite particle. By grinding the chalcopyrite concentrate by VSBM, the activation energy of leaching slightly decreased from 66 to 58 kJ/mol. INTRODUCTION Due to the increasing demand of copper, low grade ores and refractory minerals like chalcopyrite are expected to become the main copper source in the next years (Klauber, 2008). As a low-grade sulfide, chalcopyrite shall be processed hydrometallurgically. However, due to the formation of a protective layer of elemental sulfur during the oxidizing leaching, the dissolution of copper is slow and/or incomplete (De Bernardi and Carlesi, 2013). Therefore, the development of new technologies to enhance the extraction of copper from chalcopyrite is highly required."

Jan 1, 2018

By Fedotov Pavel

One of the efficient means of ore disintegration during the processing is its volume breakage in such machines as roller-presses. Up to date neither the ore disintegration mechanism in roller-presses nor the reasons of their high efficiency are thoroughly investigated. In this work, the mathematical model of Finite Element Method of bad material disintegration in roller-press is discussed. The mechanism of the interparticle ore disintegration is traced.

Sep 1, 2012

By A. Collings, A. Farmer

"Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation, which is the formation and sudden collapse of bubbles in a fluid. Cavitation occurs preferentially at solid surfaces in a liquid: at container walls, inserted objects or suspended particles. When the cavitational bubbles collapse near a solid they do so by forming a very high energy jet directed from the point on the bubble furthest from, and directed towards, the surface of the solid, in effect micro jet blasting.This paper highlights some of the major mineral processes where ultrasonics is beneficial namely: Surface cleaning of detrital mineral particles, where container quality glass sand was upgraded to tableware quality and up to 20% improvements in the sharpness of high tension separation of mineral sands was achieved"

Jan 1, 2003

By Javier Baladron, Mijail Villar, Brandt Henriksson

"In this presentation an overview will be given of what has been observed by the authors in the copper concentration industry, with a large diversity of tailing thickeners operating under different conditions, although many of them are located in the same neighborhood. A closer look will be taken at the reported performance from different sites and from different thickener designs, either conventional or high rate, including those that were retrofitted, regardless of the thickener brand. An analysis is also made of the generic correlation of the size of the thickener and the performance in terms of solids loading (or unit area) and % solids. The paper envisions a technology development route, makes a brief analysis of the economic impact of the suggested route and points out the need for development in technologies around tailings thickeners, such as automation, yield stress measurement, slurry pumping and construction methods."

Jan 1, 2014

By R. D. Alorro

Melting has become a popular pre-treatment method for municipal solid waste (MSW) incineration residues in Japan. Although the method is effective in stabilizing the hazardous organic sub-stances such as dioxin, it concentrates the heavy metals such as Zn, Pb, Cu, and Cd in a newly formed fly ash (melting fly ash). Melting fly ash is classified as a hazardous waste because of the leaching potential of these heavy metals in landfill environment. Extraction and recovery of these metals seem to be more environmentally and economically attractive than disposing the material to landfill after immobilization process. This study proposes a Carrier-in-Pulp (CIP) method as a new hydrometallurgical route to reject and recover heavy metals from fly ash. In this method, a carrier material which recovers the extracted metals is added simultaneously with fly ash to leaching solutions and is harvested from the pulp by physical separation method like magnetic separation or sieving. To demonstrate the effect of CIP method, shaking flask experiments were conducted under various conditions using NaCl solution as lixiviant and iron powder or granular activated carbon as carrier materials. In the CIP method using iron powder, more than 97 wt% of Pb and Zn were extracted from the ash to the solution phase. However, the iron powder which was harvested from the pulp by magnetic separation, recovered only Pb (more than 94%) through cementation, leaving behind Zn ions in the solution phase. Due to this problem, granular activated carbon (GAC) was considered as an alternative carrier material. Single- and multi-metal adsorption experiments using granular activated carbon were conducted as a preliminary study. Around 85% Pb and 88% Zn were recovered by GAC in the single-metal adsorption experiment, while 60% Pb and 70% Zn in the multi-metal experiment. These results showed that activated carbon was superior to the iron powder since it was able to recover both Pb and Zn through adsorption. The leaching test conducted on the residue after the CIP-Fe treatment revealed that the solubilisation of Pb was successfully suppressed to meet landfilling guidelines.

Jan 1, 2014

The air recovery from a flotation cell is the fraction of inlet air which overflows the weir as un-broken bubbles. The air recovery is an important factor in froth phase phenomena; such as gangue entrainment and froth recovery. Increasing the air recovery, results in a higher recovery of attached mineral particles. Air recovery can be measured experimentally on plant using image processing of the top surface of an overflowing froth. The air recovery is directly linked to froth stability and the bursting rate of the bubbles at the froth surface, making it very difficult to predict. Experimental results show a very strong correlation between the superficial velocity of the inlet air and the superficial velocity of the air leaving the cell through the froth surface due to bursting, calculated from the experimentally measured air recovery. This correlation holds over multiple banks from different plants. Development of a power law equation around the inlet air velocity and the bubble solids loading on the froth surface allows the superficial air velocity through the top surface of the froth to be predicted, and from this the air recovery. This model is valid for use when operating beyond the peak in air recovery.

Jan 1, 2014

By Raquel Franco de Souza Lima, Isao Matsuoka

"Microflotation studies and abstraction experiments were conducted with synthetic oxide spinels relating to chromite (MgCr2O4, FeCr2O4, FeFe2O4 and FeAl2O4), using sodium oleate as collector. An attempt was done to correlate this data with the speciation of oleate in the bulk solution and at the interface solid-water, to explain the floatability curves. The microflotation tests were conducted using a microflotation cell. The abstraction of sodium oleate was measured at 25°C, with one gram of synthetic spinel and the abstraction time was 30 minutes. After centrifuging, the residual oleate concentration in the supernatant was measured by using the spectrophotometric method described by Mizuniwa et al. (1977), that covers the range from 1.5 to 9 ppm. To cover the range from 0.2 to 1.5 ppm, the residual oleate concentration was measured using the spectrophotometric method described by Gregory (1966). The amount of oleate abstracted was calculated from the difference between initial and residual (equilibrium) concentrations.Figure 1 shows the floatability of FeCr2O4, FeAl2O4, FeFe2O4, MgCr2O4 as a function of pH and sodium oleate concentration of 1 x 10-5 M. The IEP of each sample is indicated in the figure by a vertical line in the horizontal axis. The chromium-bearing spinels FeCr2O4 and MgCr2O4 show the lowest isoelectric points (IEP), around pH 6, while in the case of FeFe2O4 and FeAl2O4, the isoelectric points lie at pH 6.5 and 7.3, respectively. It is seen that the flotation-pH curve for FeFe2O4 has a peak at the pH of the IEP, while flotation peak for FeCr2O4 appears at pH below the IEP and that of MgCr2O4 does at pH above the PZC. On the other hand, FeAl2O4 is floated at pH range between about 4 and 7,3 (IEP). This suggests that the pH value at which the maximum flotation occurs is dependent on the sort of spinel to be floated, though it appears in the vicinity of the respective IEP."

Jan 1, 2003

By J. R. Cui

The production of electric and electronic equipment (EEE) is one of the fastest growing areas. This development has resulted in an increase of waste electric and electronic equipment (WEEE). In view of the environmental problems involved in the management of WEEE, many counties and organizations have drafted national legislation to improve the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal. Recycling of WEEE is an important subject not only from the point of waste treatment but also from the recovery of valuable materials. Consumer electronic equipment (brown goods), such as television sets (TV), radio sets, and video recorders, are most common. However, recent work on recycling of waste electric and electronic equipment (WEEE) primarily focused on personal computer and printed circuit boards scraps. Based on a detailed characterization study of consumer electronic scraps, recycling of TV scraps oriented to recovery of metals is highlighted by utilizing air table separation, eddy current separation, and optical (metal) sorting process. The result indicates that a high recovery of copper could be obtained by utilizing an effective gravity separation process. The separation results reveal that air table separation is an effective technology to recover metals from consumer electronic scraps. By using a DGS table, approximately 90% of non-ferrous metals were recovered in the heavy product with a purity of 40%. Printed circuit boards and cables in TV scrap cause metals loss due to the fact that metals in printed circuit boards and cables are not liberated from plastics and ceramic materials. The study shows that eddy current separation and optical (metal) sorting process provide alternatives for recovery of metals from shredded TV scraps.

Jan 1, 2014

By D. Izerdem, S. L. Ergun

"Beneficiation of the finely disseminated valuable minerals has been an important issue in the mineral processing field for decades. Treatment of the fine materials becomes difficult with using traditional gravity concentration equipment. To investigate particles behavior in a commonly used conventional gravity concentration equipment, a comprehensive study was undertaken in a plant, which only consists spiral concentrators as concentration units. Spiral concentrators require relatively coarse material to effectively concentrate valuables as well as offering greater simplicity for especially higher grade feeds. In the current work, chromite ore (d80 = 290 µm) was treated using spiral concentrators and the performance of spiral concentrators was examined. The design of the separation circuit comprised of rougher, cleaner and scavenger stages. The resultant fractions produced by each separation unit and feed samples were analyzed to identify the particle sizes, mineral liberations and chromite content. Grade and recovery comparisons were presented in size-by-size manner and the separation tendency of the particles were determined in varying feed rate conditions. The overall results indicated valuable mineral loss of the plant and alternative suggestions were pointed to reach the target values.INTRODUCTION Spiral concentrators are simple low energy consuming devices, which are generally used for pre-concentration of the minerals. They are cost efficient equipment separating minerals mainly based on density differences of the minerals. The adjustable splitters remove the concentrate as the remaining stream continues to move down the spiral. Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational force, centrifugal force, hydrodynamic drag and Bagnold force (Atasoy and Spottiswood, 1995; Burt, 1984). Since the classification in a spiral concentrator depends on particle specific gravity and size, the operation of spirals can be analyzed using size recovery or partition curves (Bazin et al., 2014). Spiral concentrators possess multiple design parameters for a variety of applications. The design parameters that govern the performance of the spiral can be identified as the diameter, number of turns, slope, pitch and the profile of the trough. For an efficient separation on a spiral concentrator, the properties of the slurry flowing on a spiral, ore texture, percent solids and flow rate play important roles."

Jan 1, 2018

By Vladimir Vigdergauz, Sergey Kondratiev

The paper reviews the existing criteria of the formation of particle-bubble aggregates during flotation. It is shown that predictions obtained by these criteria do not completely fit to the interaction between mineral particles and air bubbles. Experimental results of the studies into the influence exerted by molecular forms of collectors on the particle-bubble interaction are reported. Rate of dry spot expansion on the surface of pyrite with various combinations of chemically and physically adsorbed xanthate are examined. It is shown that molecular forms of collectors accelerate the rate of dry spot expansion on the mineral surface after the local rupture of the water film between particle and air bubble. The authors come to a conclusion that the molecular forms of collectors remove water from the interlayer between mineral particle and air bubble during their contact. Similarities of the proposed mechanism with the action of ion-molecular associates of fatty acids and amines are discussed. Reagents with high surface pressure and rate of spreading at the water-bubble interface are required for the effective interfacial dewatering. It is concluded that the value of surface pressure can serve as the criterion for efficiency of physically adsorbed reagents. The low surface pressure indicates weak collecting ability but high selectivity of the collector. Therefore, the presence of the molecular forms of collectors in the sorption layer is the necessary condition for formation of particle-bubble aggregates, and comparison of the surface tensions of collectors could be recommended as the estimation criterion of their flotation activity and selectivity.

Jan 1, 2014

By Tsuyoshi Hirajima, Hideyuki Okamoto, Himawan .. T. B. M. Petrus, Keiko Sasaki

"Flotation of arseno bearing minerals from their copper ore has been an interest due to the increasing awareness on protecting the environment by minimizing the possibility of exposed arsenic compound. Some approaches have been proposed, but the mechanisms of separations have not yet fully understood. In this study, oxidation using oxygen was applied. Instead of the complex copper ore flotation results, pure single mineral of tennantite and chalcopyrite foatability was conducted using Hallimond tube. Resembled with the flotation results of copper concentrate containing tennantite, the separation possessed the best result at alkaline condition (pH 11) at where the arsenic content was reduced from 3300 ppm to 1800 ppm. In order to be able to understand the mechanism of the separation atomic force microscope (AFM) was utilized. AFM images showed changes in morphology and behavior when minerals were treated in both acid and alkaline condition. It was found that the morphological change showed the reaction products representing the rate of reactivity of tennantite and chalcopyrite. From the measured force of adhesion, it can be observed that in alkaline condition the surface of both minerals is more hydrophilic than that in acidic condition possessing higher value. This is in accordance with the X-ray photoelectron spectroscopy (XPS) spectra in which hydroxide moieties occupied the mineral surface in alkaline condition while elemental sulfur is in acidic condition."

Jan 1, 2014

By Khoi Nguyen, Luke Keeney

"Hardness" is an important yet diverse material physical property and is a key parameter in the mining industry in fields such as comminution, geotechnical and blast modelling. Several laboratory and field based measurement techniques exist to measure hardness (e.g. Point Load Testing, Vickers, Brinell, A*b, BMWi, UCS), all are designed for specific applications. Current tests are generally destructive and require specific sample preparation procedures which results in high cost tests that are not conducted in adequate quantities to map hardness across an ore body. The EQUOtip rebound hardness tester is a device that has been developed for application in ore body hardness domaining within the AMIRA P843 GeMIII Research Project. The rebound hardness test is non-destructive and suitable for application on half and whole diamond drill core. Data acquisition protocols and a data processing software application (EQProcess) have been developed to facilitate routine collection of comparative hardness information. This paper outlines the data acquisition and processing methodology and provides application examples of defining relative hardness domains in different geological deposit styles.

Jan 1, 2014

By Nicolus Rotich, Ritva Tuunila, Louhi-Kultanen. Marjatta

Most minerals, their ores, and gangue require sorting in order to maximize the recovery of the primary product during concentration. Gravity separation though old, is not obsolete and is continually playing an important role in mineral processing and many other industries, especially where plant energy efficiency is of concern. Screen designs e.g. material of construction, deck angle of inclination, the feed throughput, and physical as well as chemical properties of the particles, are critical factors to consider when using gravity for solid separation. Solids loading and screen geometry are significant, and easily manipulated operational parameters that affect both the screening rate and efficiency to a large extent. In this paper we applied nonlinear least squares optimization technique, and response surface methodology first, to assess the significance of the two factors, and secondly to select the best mathematical models that optimize both capacity and efficiency of the screening process. Initial experiments and confirmation tests were conducted on a prototype screen of 846.51cm2 effective area, (2100 cm2 total area). For glass beads of sizes 0.75-3mm, with feed loads of 10g up to 160g, and inclination angles from 5-20o, a maximum efficiency of 66.7%, and a screening rate of 22g/s was achieved with a screen loading of 86.5g, and an inclination angle of 12.43o. These results were then subjected to nonlinear least squares optimization, in which afterwards an optimum theoretical efficiency of 72% and screening rate of 31.2g/s were achieved at a loading of up to 104g. There was excellent performance at angles 12.5=?=17.5, but poor at the angles outside this range. The screening efficiency did not seem to respond significantly to changes in screen loading. Confirmation tests conducted at selected optimum parameters achieved an efficiency of 72.1% (at 17.5o with 88g load), and a rate of 27g/s at 16.5o with 104g.

Jan 1, 2014

By V. E. Vigdergauz

The work presented shows results of electrochemical study of pyrite hydrophobicity evaluated by air bubble induction time (IT) measurements. On the basis of measured IT?s an average thickness of the thin liquid film prior to its rupture has been evaluated, which confirms long-range character of the interactions between air bubbles and hydrophobic surfaces. Obtained data are discussed in the frame of recent studies of structures of solid-liquid interface based on molecular dynamics simulations and results of surface force measurements.

Jan 1, 2014

By Eduard Stefanescu, James M. Mwase, Egon Sehner, Stoyan Gaydardzhiev

"The study is focused on investigating the production of synthetic rutile of 95% purity or higher from a Norwegian ilmenite ore concentrate. This was to be achieved using a sequential process involving oxidative-reductive roasting at 975°C, followed by magnetic separation to further concentrate the sample and finally leaching with 20% HCl to remove mostly Fe-based impurities leaving behind synthetic rutile. The key process parameters considered were roasting time (1 and 2 hrs), leaching temperature (100, 125 and 145°C), pulp density (15 and 25wt%) and leaching time (3 and 6 hrs). The option of directly leaching the concentrate without pre-treatment was also evaluated. Test work was conducted using samples screened to a size fraction of 105-212 µm. Samples were leached in a 1 L glass autoclave. The reactor was hermetically sealed and thus the resulting pressure was not controlled but was dependent on the process temperature. The product from leaching was calcined and analysed via XRD and SEM to determine the purity of the product. The magnetic separation step was found to be ineffective and discontinued early in the study. Thus far a product with 97% synthetic rutile purity as analysed by SEM has been produced by directly leaching the concentrate at a temperature of 145°C, pulp density of 25wt% and leaching time of 6 hrs.INTRODUCTION The study investigates the use of a process route comprising oxidative-reductive roasting, followed by magnetic separation and then hydrochloric acid leaching and calcination to produce synthetic rutile from ilmenite concentrate. The grade of synthetic rutile produced should be suitable for chlorination to produce pigment grade TiO2. Hence the proposed process should produce a product consisting of no less than 95% synthetic rutile. Additionally, the product should have no more than 1.5wt% combined content of CaO and MgO (Zhang et al., 2011) as they tend to form high-boiling-point chloride leading to the malfunctioning of fluidized bed chlorinator (Cardarelli, 2008). Finally the product should have no more than 2.1wt% of Fe2O3."

Jan 1, 2018

By H. Lieberwirth, M. Hesse

"Selective comminution (SC) is beneficial for the treatment of primary raw materials, especially if it is utilized in the pre-concentration process. Pre-concentration processes are applied in mineral processing to relieve subsequent processes and to achieve a higher efficiency. SC is also a promising method for the treatment of low-grade ores and waste dumps. With SC, various components can be separated such as valuable minerals from waste, ore from wall rock and different ore varieties within a deposit. SC is a property of a comminution system and leads either to a preferred crack propagation in one component (called preferential breakage) or to a preferred crack propagation along the grain boundaries (called interfacial breakage). SC results from different comminution behavior of various components in the feed material. For mechanical comminution, the preferential breakage seems to be the most important case of SC. Hereby SC generates only the difference in the particle size which can finally be used as a sorting parameter. A sorting process which uses SC depends on three parts: the feed material, the comminution machine and the separation machine. The feed material defines the potential for SC. Differences in properties like strength, toughness and density which are related to comminution are often used. The comminution machine has to exploit this potential. The extent of the exploitation can be influenced by the machine design, material and operational parameters. After SC, the various components are still combined in the product. So ultimately, a separation machine is needed. At preferential breakage, a simple screening machine can be used. The basics about SC will be presented at first. This contains relationships between material properties, the kind of loading in the comminution machine and the SC effect. These basics can be used for example to exploit a potential to SC for a pre-concentration step or to avoid the SC for a higher efficiency of subsequent processes. Based on recent investigations with impact load, the influence of the important parameters compressive strength, density, particle size and impact velocity to the SC will be shown, using examples of lead-zinc ore comminution and fluorspar processing."

Jan 1, 2018

By M. Kargar Razi

According to the unique properties and many applications of nano gold powder, it was prepared from an acid leaching tail solution. The low value residual gold ions were existed in acid leaching tail solution in Mouteh gold mine in Iran with fellow heavy metals as pollutants (FeP2+P, Cu P2+P, and ZnP2+P). Preparation of nano gold particles is achieved by two steps. First, by addition of ammonia as separation step and second using suitable reagents for precipitation/extraction step. Conditions control includes pH, residence time, temperature, agitation, and molar ratio of reducing agents to reagents. The optimum results show that nano gold powder was prepared by temperature of 250 °C, urea to gold molar ratio of 3:1, and reduction time of 20 min. Also, heat treatment improves dispersion of nano sized gold particles. The properties of gold nano powders were evaluated by SEM, A.A, and UV- Vis spectroscopy methods. The size of prepared particles were about 80nm to 90nm.

Jan 1, 2014

By R. Venugopal

The paper reviews the development of Mineral Engineering education and training programmes in India. It highlights the major academic programmes and describes the evolution of the curriculum and design of courses in response to the changing requirements of India?s mineral and coal industries. An outline of the efforts needed to sustain and further improve the existing programmes is also provided. Keywords: manpower, mineral engineering

Sep 1, 2012