Search Documents

By D. Pienaar, B. McFadzean, T. Jordaan

"Dithiophosphate (DTP) collectors have the lowest affinity for sulfide mineral surfaces compared to other common sulfide mineral collectors, such as xanthates and dithiocarbamates. In some cases it has been found that DTP does not adsorb onto the mineral surface at all and yet increases in recoveries and grades are noticed with the addition of DTP. Many studies have investigated the interactive effects of collector mixtures. However, there have been relatively few studies on the interactive effects between frother molecules and collectors. This study investigates the interactions between different types of frothers and sodium diethyl dithiophosphate.The study found that there were large increases in pyrite and galena microflotation recoveries at both pH4 and pH9 when DTP was mixed with small amounts of frother at a constant bubble size, showing that these increases were neither mineral-specific nor pH-specific. The same effect was not present when xanthate was used as a collector. The increases in recovery when using the DTP-frother mixture were similar irrespective of the type of alcohol or polypropylene glycol frother that was used. In an attempt to distinguish the mechanism of enhanced flotation recovery, various supplementary experiments were performed. It was found through adsorption experiments that no DTP was adsorbing on to the mineral surface. Therefore, interactions at the air-water interface were performed. Surface tension and critical coalescence concentration tests showed that, while DTP is a weak surfactant at the air-water interface, it does not have a synergistic effect in the presence of frother. DTP-frother mixtures do, however, show interactions in the froth phase, indicating an interaction in the thin films. It is proposed that there is a DTP-frother interaction on the bubble surface that enhances the rate of film thinning at the 3-phase bubble-particle contact."

Jan 1, 2018

By Leon Lorenzen, Nursen Guresin, Harald Muller

The development of mining projects from discovery, exploration to actual production is a complex and time consuming process. Often poor process plant performance can be attributed to the use of non-representative samples and inadequate and/or unsuitable metallurgical test work when designing flow sheets during project feasibility study stages and specifying process equipment. Samples not representing the ore deposit and inadequate test work may lead to increased project development costs, since expensive test work and engineering may have to be repeated. It should be noted that for higher level engineering studies, larger scale test work is recommended and is a requirement for feasibility level studies. This would apply even if the technology is considered mature and well proven, as each ore body may have its own unique characteristics that, if untested at a larger scale, could result in significant design shortcomings, which will have to be rectified at later stages of the project, usually at significant additional costs

Jan 1, 2014

By F. Bello, R. Yanez, M. Pinto, T. Errazuriz

"Throughout its operation, Minera Esperanza (ME) will deposit one of the largest tonnages rates of high density tailings in the world with a solids concentration of close to 67% by weight. The tailings presently being deposited have a solids concentration of approximately 62% - 64%, and so cannot be used to directly characterize the flow and deposition characteristics of the higher concentration tailings. To increase the knowledge of the behaviour of their tailings, ME, with the support of Golder Associates, developed a large scale tailings deposition test with a capacity of 30,000 tonnes per day (1,200 m3/h). The test was carried out by depositing tailings into two large cells or paddocks in five stages. Multiple spigots were used to allow different flows to be deposited. At each stage, topographical surveys of the natural terrain and the geometry of the deposited tailings, as well as continuous flow measurement and periodical rheological characterization of the discharged tailings were conducted to create a data set against which beach slope models could be calibrated and then used to predict performance of the higher concentration tailings under different deposition scenarios. This study adopted the beach slope prediction model proposed by A.L. Li (Li, 2011). The model was successfully adjusted to the observations made during this large scale field test by applying the values measured in-situ. This paper presents the application of the model, the results obtained, the findings, and the analysis of possible future scenarios. The model was applied, using the discharge flow rate, the geometrical characteristics of the discharge area, and the rheology with its variation along the beach to estimate the development of the beach formation and the steady state of the beach slopes. Through the use of dimensionless variables, the model was applied to higher solids concentration scenarios, obtaining results that would allow beach slope estimation at different deposition stages in multiple scenarios of varying parameters such as flow, rheology and geometry of discharge area."

Jan 1, 2014

By S. Carsten, S. Subramanian, R. Vasant Kumar, S. Vimalnath

"The effect of EPS components namely protein, polysaccharide and biosurfactant purified from Pseudomonas fluorescens was investigated for the bioremediation of Pb(II) ions in aqueous solution. Two parameters, namely the amount of EPS component and the concentration of Pb(II) ions were optimized for maximum Pb(II) ions uptake. The EPS components interacted with Pb(II) ions were characterized using energy dispersive X-ray analysis (EDAX) to ascertain the presence of Pb and by attenuated total reflection-Fourier transform infrared spectroscopy (ATR–FTIR) to reveal the functional groups involved in Pb(II) binding. The maximum Pb(II) binding capacities of protein, polysaccharide and biosurfactant were found to be 11.4, 0.55 and 0.11 mg mg-1 respectively. The biosorption processes followed the Langmuir model. The Gibbs free energy (?G0) values of -23.6, -20.9 and -23.2 kJ mol-1 for Pb(II) biosorption by protein, polysaccharide and biosurfactant respectively, attested to spontaneous, chemisorption processes. The ATR–FTIR results revealed the presence and involvement of amino, hydroxyl, carboxyl, phosphate, and methyl functional groups in Pb(II) binding and EDAX analysis confirmed the interaction of Pb with EPS components. The Pb(II) binding mechanisms of EPS have been discussed. The results demonstrate the potential of the purified EPS components of P. fluorescens for removal of Pb(II) ions from aqueous solution INTRODUCTION Waste water containing toxic metals from various industries pose a serious threat to human health and ecosystem. For treating such waste water, conventional methods like chemical precipitation, coagulation, evaporative recovery, electrodialysis, floatation, flocculation, ion exchange, reverse osmosis, nanofiltration, ultrafiltration are used (Lakherwal et al., 2014). These methods have some disadvantages like toxic sludge generation, incomplete metal removal and high cost (Singh and Gadi, 2012), necessitating the search for cheaper and efficient alternative methods. Bioremediation is one of the emerging alternatives where bacteria, fungi, yeast, algae and other biological substances are used as sorbents to remove toxic heavy metals (Vijayaraghavan, et al., 2015). Recently, the bioremediation potential of extracellular polymeric substances (EPS) of microbial origin has attracted attention. However, for Pb(II) removal, there is a paucity of literature focusing on EPS."

Jan 1, 2018

By G. P. Karmakar, K. K. Chandan

"The drilling mud is an essential part of the drilling process, which plays a major role in keeping safe and efficient oil and gas well drilling. In the oil industry, bentonite clay dissolved in water produces the simplest type of drilling muds. Bentonite clay contains montmorillonite particles. These particles are dispersed uniformly in water and such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds. The bentonite clay easily dissolves in water and increases the viscosity of the water, which is one of the most important properties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for building up of the viscosity of the clay-water system. The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil and gas well drilling process. The behavior of drilling mud greatly depends upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations. In this work, a comprehensive study has been carried out to find out the effect of added polyacrylamide (PAM) polymer, surfactant, pH and salt concentrations on the dispersion/ flocculation characteristics of bentonite clay-water system. It has been observed that the increase in PAM dosage reduces the residual turbidity and improves the settling rate of the bentonite particles. The flocculation rate has also been found to be better under higher pH conditions. The combined effect of salt concentration and PAM dosage improved the overall flocculation efficiency of the system.INTRODUCTIONIn the oil industry, bentonite clay dissolved in water produces simplest type of drilling muds. Bentonite clay containes montmorillonite particles. These particles are dispersed uniformly in water. Such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds (Akther et al., 2007). The bentonite clay easily hydrates in water and increases the viscosity of the mud system (Razi et al., 2013; Meng et al., 2012). Bentonite clay in the drilling mud increases the viscosity which is one of the most important prop erties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for the building up viscosity of the clay-water system (Sonmez et al., 2013). The drilling mud is an essential part of the drilling process, which plays a major role in keeping a safe and efficient oil or gas well drilling (ASME, S. S. C., 2005). The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil or gas well drilling process. This behavior of drilling muds greatly depend upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations (Yu and Amanullah, 2005; Akther et al., 2007). Bentonite particles form aggregate under certain conditions including high temperature, and high concentration (Luckham and Rossi, 1999). If the quality of bentonite is not sufficient to accomplish intended viscosity of the muds, it is essential to add certain additives to increase the viscosity and prevent aggregation of the system (Razi et al., 2013). The anionic polymer bearing sample can build up inter-particle bonds between the polymer and clay particles. The addition of various additives like, polymers control the dispersion and enhance the viscosity of the mud by controlling the flocculation of montmorillonite particles in bentonite dispersion (Heller and Keren, 2002; Mahto and Sharma, 2004)."

Jan 1, 2018

By G. Pahomova

"It developed an alternative to traditional flotation enrichment refractory of complex lead-zinc ores to obtain conditional lead and zinc products. The scheme involves the use of the processing method of gravitational enrichment of the primary cycle and the combined gravity-flotation-hydrometallurgical in finishing. The method has a high level of comprehensive utilization of mineral raw materials in relation to the elements that are extracted in the process of enrichment in lead concentrate, and the increase in recoverable value of processed ores. INTRODUCTION The primary source of lead are complex sulphide lead-zinc ore, lead ore actually rarer. The value of lead and zinc ores (except lead and zinc) is determined by the presence in them of a wide range of associated components: silver, contained mainly in galena; gold; bismuth in the form of its own minerals, but is associated with galena; cadmium contained mainly in the sphalerite; indium, thallium and gallium contained in sphalerite and galena; selenium and tellurium are present as impurities in the sulfide, tellurium is also found in the form of its own minerals. Of note harmful impurities antimony, which is often associated with lead sulphosalts and arsenic, having a substantially own minerals. By quality (content of lead, or the total content of lead and zinc) lead-zinc ores are divided into rich, ordinary and poor; by oxidation - to sulfide (with a lead oxides content less than 15% and zinc oxide content less than 10%), mixed and oxidized (50% oxide); the latter have a subordinate importance as a source of zinc and lead. Traditionally, the most contrasting technological properties of sulfide ores of nonferrous metals considered flotation properties, which determines the priority in the selection of flotation technology of their enrichment. Other methods of enrichment - gravity (jigging and enrichment in heavy suspensions), radiometric sorting (separation) are used as preliminary operations whose main purpose is to increase the content of lead and zinc in the ore sent to flotation, as well as the removing of part of empty rock in dumping tails prior to flotation. Effective implementation of these methods is possible at large size emphasizing in the ore of lead and zinc minerals, which is typical of the rich ores and which so far mainly worked. At the same time, non-ferrous metal ores (polymetallic, lead-zinc, copper-zinc, etc.) have a sufficiently high contrast to gravitational properties since ore minerals have a higher density compared with a rock minerals. But the gravity of the practice of non-ferrous ores enrichment is not widely used, despite its high degree of environmental safety and lower cost expensive."

Jan 1, 2018

By V. F. Petrov, E. P. Olberg, S. V. Petrov

"The study was carried out using process solutions produced during cyanidation of gold-bearing concentrates from a gold-processing plant. It was found that the water contained a significant portion of thiocyanate (7910.0 mg/L), cyanide was virtually not present. The metals occurred primarily as iron (355.0 mg/L) in the form of ferrocyanide. Cyanide recovery was conducted using an ozone treatment process with reactors developed by the Environmental Department of Irgiredmet. The process design ensured complete utilization (100%) of O3, thus equipment operation safety increased.The recovery of free cyanide from thiocyanate was 76.6%, which corresponded to 5.12 kg of NaCN (100%) per 1 m3 of solution. Recovered NaCN can be used for recycling in hydrometallurgical processes.The operating costs estimation showed that the production cost of a tonne of recovered cyanide was US$1288.7, considering the prices of energy and commercial sodium cyanide in Russia in 2017, i.e. recovered cyanide is cheaper than commercial cyanide by 55.8%.INTRODUCTION Depletion of oxidized gold-bearing ores readily amenable to cyanidation has shifted focus to large-scale processing of primary ores with high sulphide content. Primary ores processing flow sheets involve gravitational and/or flotation concentration with subsequent treatment of produced gold-bearing concentrates. Typically, concentrates reporting to cyanidation contain considerable amounts of sulphur that can interact with CN- and further formation of SCN-. The use of refractory gold liberation methods (bacterial liberation, ultra-fine grinding) provides activation of this side reaction up to complete consumption of free cyanide in a short period. This makes water recycling unviable and impractical.The interaction of the sulphur content in concentrates and cyanide contributes substantially to consumption of NaCN required for efficient gold recovery. Inappropriate consumption of the main reagent achieves dozens of kilogram per tonne of material to cyanidation, and reaches approximately 100% when gold is recovered from activated sulphide-containing products (e.g. by ultra-fine grinding)."

Jan 1, 2018

By Richard A. Williams

The mineral processing community have been amongst the pioneer developers and early adopters of key platform technologies in analytical methods, chemistry, physical separation and advanced modelling. Fundamental research will continue to have a significant impact driven by the continued development of sustainable practices. Major drivers and challenges for change in our industry in the next two decades include: reduction in energy uses in processing; discovery of new energy materials; adoption of green chemistry routes; safeguarding of water resources; and demonstration of adherence to best practice at all times. With increasingly global mining enterprises, the provision of internationally accepted benchmarks for performance will continue to drive the creative process. This lecture highlights major opportunities around a new paradigm of Multi-scale Measurement coupled with Multi-scale Modelling, based on advanced sensors, communications and computing. Connecting real-time measurement sensors with dynamic simulation models opens up new horizons for visualising the process behaviour from an experimental and theoretical basis. Examples are given of the potential of this methodology and its implications for better design.

Jan 1, 2003

By I. Silin, H. Wotruba, J. Huben, A. Ognyanova

"With increasing shortage of raw materials, the beneficiation of ultra-fine ores will play a larger role in the near future. Many established process technologies do not yield satisfactory separation results for ultra-fine materials. Without selectivity, high-grade concentrates cannot be produced. The material at hand is a taconite which had to be ground to d(90) = 25 µm to guarantee liberation of the iron oxides. The comminution was done by High Pressure Grinding Roll (HPGR) and resulted in smooth surfaces and clear grain boundaries. This is an indication of selective grinding and mineral liberation. Further processing steps included selective desliming, magnetic separation as well as reverse flotation. INTRODUCTION During the last centuries, the processing of iron ores became increasingly important. The coarse-grained, so-called lump ores that are ready for direct usage in blast furnaces without further processing are becoming gradually less abundant. The processing of ultra-fine-grained ores, which in addition require a complex ore beneficiation due to the composition of the material, will progressively gain relevance with increasing resource shortages in the future (Arvidson, 2013). The term “ultra-fine” does not hold a precise definition in mineral processing. In this paper, “ultra-fine-grained” ores are defined by the required grind size for full liberation smaller than 20 µm. Many established mineral processing technologies do not yield satisfactory separation results for ultra-fine materials. Thus, they are limited in their application to produce high-grade concentrates suitable for sintering and pelletizing for direct reduction processes. The production of a high-grade iron concentrate (over 68% Fe) with low silica content (under 2.5% SiO2) is possible from both magnetite and hematite containing ore. In addition to the mineral processing technologies (magnetic and gravity separation, flotation), technologies for the liberation of fine-grained iron ores need to be developed and improved. In contrast to the conventional wet grinding circuit by means of tumbling mills, several future trends in dry and wet grinding and regrinding are already in use. These include technologies such as vibration mills (Palla®Mill), stirred media mills (Vertimill®), vertical roller mills (Loesche) and high-pressure grinding rolls (HPGR) (Jankovic, 2015). This study preliminary investigated the mineral processing of a low-grade, ultra-fine-grained, complex iron ore in a laboratory scale after dry grinding by HPGR to 90% < 25 µm without consideration of the grinding, milling, energy and classification cost."

Jan 1, 2018

The reactivity of clay minerals and variety of these reactions are greater than any other known colloidal material. While it is acknowledged that clay minerals can cause problems in mineral flotation, the literature contains conflicting evidence, particularly with respect to the effect of clays on froth stability. It is well known that achieving and maintaining optimum froth stability is an influential factor in determining froth flotation performance. However, the presence of clay minerals in the ore is a major challenge to obtaining a stable froth. In fact, clay minerals could reduce froth flotation performance by both decreasing and increasing froth stability. The mechanism by which clay minerals affect froth stability is not fully understood and needs to be investigated further. In order to improve flotation performance, reliable knowledge of the effect of clay minerals on froth stability is essential which is discussed in this paper. Keywords: froth flotation, froth stability, clay, clay minerals

Sep 1, 2012

By T. Suzuki

Acid leach liquors from spent lithium-ion batteries employing lithium cobalt dioxide (LiCoO2) as a cathode active material contain valuable metals such as cobalt and lithium, as well as common metals such as aluminum and copper. The objective of this study was to develop a hydrometallurgical process providing a high selectively between aluminum, cobalt, copper, and lithium from hydrochloric acid solutions. Batch experiment results showed that selective hydroxide precipitation approach was not suitable because a significant amount of cobalt and lithium was co-precipitated with aluminum and copper hydroxides. In contrast, batch experiments and the subsequent data analysis indicated that the sequence of solvent extraction circuits using PC-88A, Acorga M5640, and tri-n-octylamine (TOA) extractants effectively separates four metals of interest. In the first circuit of the proposed process, copper was selectively extracted by Acorga M5640 at the pH 1.0-2.0. Aluminum, cobalt, and lithium remain in the aqueous phase. In the second circuit, aluminium is selectively extracted by PC-88A at pH 2.0-2.5. For the separation of remaining cobalt and lithium, Acorga M5640 provided higher separation efficiency compared to PC-88A single extractant and PC-88A/TOA mixed extractant. However, the stripping efficiency of cobalt from the Acorga M5640 organic phase was found to be low (less than 10 %). Therefore, PC-88A/TOA mixed extractant rather than Acorga M5640 is an advisable choice for the separation of cobalt and lithium. Keywords: spent lithium-ion secondary batteries, solvent extraction, lithium, cobalt

Sep 1, 2012

By Alireza Javadi Nooshabadi, Kota Hanumantha Rao

Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by sulphide minerals during grinding was examined. It was found that pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite ((Zn, Fe) S), and galena (PbS) generated H2O2 in pulp liquid during wet grinding and also when the freshly ground solids are placed in water immediately after dry grinding. Pyrite produced more H2O2 than other minerals and the order of H2O2 production by the minerals was found to be pyrite > chalcopyrite > sphalerite > galena. The pH of the water influenced the extent of hydrogen peroxide formation with greater amounts of H2O2 produced at highly acidic pH. Furthermore, the effect of mixed sulphide minerals, i.e., pyrite-chalcopyrite, pyrite-galena, chalcopyrite-galena and sphalerite-pyrite, sphalerite-chalcopyrite and sphalerite-galena on the formation of H2O2 showed increasing H2O2 formation with increasing pyrite fraction. There is clear correlation of the amount of H2O2 production with the rest potential of the sulphide minerals; the greater the rest potential of a mineral the greater the formation of H2O2. This study highlights the necessity of revisiting the electrochemical and/or galvanic interactions between sulphide minerals, and interaction mechanisms between pyrite and other sulphide minerals in terms of their flotation behavior in the context of inevitable H2O2 existence in the pulp liquid.

Jan 1, 2014

High flotation of iron sulfide minerals at high pH values in copper ores is mainly due to the activation of these minerals by copper species dissolved from copper sulfide minerals during grinding. Several methods have been tested to reduce this copper activation during grinding and therefore to depress iron sulfide flotation. They include grinding the minerals at high pH values or with a less reactive medium such as high chrome, and addition of a thiol collector or copper complexant during grinding. The efficacy of these methods in the flotation of a copper ore was tested against more common methods of depression of iron sulfide flotation. The mechanism of iron sulfide depression in these methods was also investigated.

Jan 1, 2014

By Lucy van de Ruit, Megan Becker, Aubrey Mainza, Jenny Wiese

"UG2 chromitite ore is a complex, highly disseminated platinum ore from the Bushveld Complex in South Africa, with typical platinum group mineral (PGM) grain sizes below 15µm. The introduction of stirred mills to the platinum industry has enabled grinding to finer product sizes, which has improved liberation and recovery of the finely grained PGMs. However, reduction in particle size leads to an increase in chromite entrainment in the flotation concentrate, which has a negative impact on the subsequent smelting process. Factors such as particle size, froth structure, solids concentration and water recovery have all been identified as impacting entrainment, but whether particle shape also has a significant effect is unclear. The purpose of this study was to determine whether the recovery of chromite particles by entrainment during the flotation of UG2 ore is affected by particle morphology. A laboratory vertical stirred mill with inert ceramic media was used for grinding UG2 ore which was then floated in a batch flotation cell. Flotation feed and concentrate samples were analyzed using QEMSCAN to quantify the angularity and aspect ratio distributions of the particles. The stirred mill product was found to have relatively broad aspect ratio and angularity distributions, with the major mineral components (chromite and silicates) having very similar shape characteristics. Analysis of flotation feed and concentrate samples suggested that particle shape does not have a significant effect on chromite entrainment."

Jan 1, 2014

By Gaurav Soni, Roe-Hoan Yoon

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model predictions have been compared with the results of a series of laboratory flotation tests conducted using mono-sized glass beads of different particle sizes and contact angles under different operating conditions. Some of the experiments were conducted using a 1:9 mixtures if hydrophobic silica and hydrophilic magnetite, so that the product graded could be readily determined by simple magnetic separation. The model predictions are in good agreement with the experimental results both in recovery and grade. A computer simulator developed on the basis of the model is capable of designing a preliminary flotation circuit on the basis of feed characteristics, e.g., size-by-liberation data, and the hydrodynamic information on the flotation cells to be incorporated in the circuit.

Jan 1, 2014

By Egbert Burchardt

"Some of the challenges faced by the mineral industry in the future are the need to process low grade ores at the lowest operating cost, to deal with elevated energy cost and to address scarce water resources in some regions of the world. These challenges will increase the demand to develop highly energy-efficient and less water-consuming mineral processing systems. Experience from other industries suggests that HPGRs could help to achieve these goals, due to their high energy efficiency and their ability to be used as dry grinding systems. Historically, HPGRs have been used mainly as tertiary crushers in mineral applications for the production of ball mill feed. In the cement industry, however, HPGR systems have been successfully applied for grinding limestone, clinker and slag to a final product fineness (p80) of between 30 and 90 µm without the need of downstream ball milling. The total energy consumption of HPGR finish grinding systems in the cement industry has been found to be 30 to 50 % lower than in ball mill systems. This leads to the question of whether the same methodology can be adopted in the mineral industry. Such a step would require the use of dry rather than wet grinding systems. Traditionally, dry grinding systems have been only an exception in mineral processing, since most post grinding processes are wet. However, there are successful - mainly ball mill based - dry grinding examples in gold, nickel or iron ore. Experience from some of these dry grinding references are summarized in this paper. In addition, this paper explores two future-orientated questions: What opportunities does HPGR finish grinding offer the mineral industry? What are general conditions and challenges for adopting this technology for mineral applications?"

Jan 1, 2014

By J. Bhattacharya

In many different ways industrial raw materials resources industry as a whole has accepted the principles of sustainable development and has made a commitment to move toward this goal. The critical question now is ?how?? While many companies have adopted policies and are implementing community relations programs, sustainability is not always ?lived? throughout the organization. While traditional programs and commitment from the top are critical, employees within all functional areas can advance sustainability. Individuals can make difference at all organizational levels, and it is this collective action that is so critical for enhanced financial performance as well as the preservation of the industry. Keywords: value chains, sustainability, legislation, auditing process

Sep 1, 2012

By V. V. Musaev, A. M. Klyushnikov, R. R. Galimov

"A study was made of chemical and material compositions of the oxidized gold-bearing ore of the Kochkovskoe deposit. It was demonstrated that examined ore consisted mainly of quartz, carbonate and feldspar with a gold content of 2.2 g/t and a silver content of 6.1 g/t. By means of agitation leaching tests it was founded that about 79-80 % of gold can be extracted from ore using cyanide leaching solutions. The achieved high-speed dissolution rate of gold was due to its presence in a finely dispersed state (less than 2.73 µm), which was confirmed by the research of Uralmekhanobr. It was proposed that the ore can be processed by heap leaching process using cyanide leach solutions. Technological studies on the modeling of the heap leaching process were initially carried out in percolators with a capacity of 5 kg on agglomerated ore. It was preliminary established that agglomeration should be carried out at a cement consumption of 12-16 kg/t, with the moisture content in pellets reaching up to 10-12 %. The best percolation leaching results can be obtained with ore crushed to the size of -20 mm. The maximum extraction of gold to the solution was 79-80 % while the L:S ratio reached 1.2-1.4:1.In cooperation with the research center of OJSC ""Berezovsky mine"" a semi-industrial heap leaching test was accomplished. The result of a test performed was an extraction of 78.5 % of Au and 21 % of Ag from ore to a pregnant solution. This extraction degree was achieved at a L:S ratio 0.9: 1. On the ground of results obtained, a technical regulation was developed for design of the heap leaching plant with the capacity of 500 thousand tons of ore per year.INTRODUCTION The ore of the Kochkovskoe deposit represents an important reserve of gold in the Zabaikal region. Of the upmost interest are oxidized ores, the processing of which can be carried out by heap leaching (HL) with cyanide solutions. The purpose of this work was to study the composition and to develop a technology for heap leaching of oxidized ore."

Jan 1, 2018

By l. Bokányi, T. Varga

"The recycling of waste car tyres is a very important environmental task. The waste tyres usually are re-used or recycled by thermal processes like pyrolysis, gasification or incineration. The main problem associated with these processes is the sulphur content of waste tyres originated from the vulcanisation process, which pollutes the environment and the valuable products (i.e. pyrolysis oil) as well. In our research the desulphurisation of waste, mechanically prepared tyre sample was systematically investigated by the biosolubilisation with Acidithiobacillus thiooxidans, strain Karitas. Parallel, the experiments with sterile 9K nutrient medium were also carried out. It was found that the vulcanisation sulphur can be solubilised due to both the bio- and the chemical leaching, although the bioleaching is more effective. The solubilised vulcanisation sulphur then forms precipitates. The precipitates are forming in the bulk solution, as well as on the surface of rubber particles. The origin of the precipitates was investigated using XRD and scanning microscopy with micro probe. The origin of the precipitates is different: while in the process of the vulcanisation sulphur solubilisation with 9K medium the jarosite (KFe3+3(SO4)2(OH)6) forms, the course of the biosolubilisation with Acidithiobacillus ferrooxidans Karitas is accompanied by the formation of the jarosite and the halotrichite (FeAl2(SO4)4 · 22H2O) as well. The formation of the latter is the biomineralisation. The mechanisms of the bio- and chemical solubilisations are rather different as it was found and experimentally proved by several tests, and depends on the retention time of the solubilisation. Special efforts were done to elaborate the proper separation of the precipitates from rubber particles. Combination of intense dynamic stirring and recycling flotation process to remove the precipitates was applied for this purpose. The surface properties of synthetic jarosite were revealed using zeta-potential measurements at different pH and in presence of collectors. The parameters of the flotation were chosen based on the revealed surface properties of the precipitates. Finally, the sulphur recovery of the recycled rubber was achieved as low as <0.5%, sulphur content of it 0.17%, 12-times lower than that of the waste tyre sample after mechanical preparation."

Jan 1, 2018

By Kal Sastry, Anshuman Prasad

This paper presents a population balance model (PBM) for describing the agglomeration process and select a suitable coalescence kernel that can simultaneously describe nucleation, layering and coalescence mechanisms. The PBM is solved numerically by making use of a size discretization procedure in order to simulate iron ore agglomeration in rotating drums where moist feed is added to preformed seeds. Subsequently, a comparison of computer simulation results with the previously published experimental data is provided. Finally, the paper discusses how the current approach can be further extended to the simulation of industrial iron ore agglomeration circuits operated in closed circuit.

Jan 1, 2003