Search Documents

By Laura A. Sanders

Mineral scale formation is prevalent in numerous mining operations. Such scale formation can occur in the direct-contact heat exchangers ahead of an autoclave. In these heat exchangers, the incoming slurry comes into contact with steam in a stage-wise fashion, which is re-circulated from the downstream flash vessels to heat the slurry in stages ahead of the autoclave. Calcium sulfate scaling causes severe problems in mining operations where increased temperatures are involved due to rising temperatures promoting calcium sulfate scaling through a decreasing solubility. In a number of these operations, the scale formation can occur in the presence of mineral solids, where fine-grained charged particles are at concentrations in excess of 35%. Scale prevention is not difficult in standard aqueous systems; however, the presence of solids leads to significant deficiencies in the prevention of scale due to the adsorption of the polymer onto the charge solids instead of the polymer interaction with the scale. Therefore, a technical solution to prevent mineral scale build up occurring in presence of pulp slurry in mining operations is needed. Several novel antiscalant technologies were developed and evaluated which provided a substantial improvement in the scale prevention in such systems.

May 1, 2013

By Jan Drzymala, Przemyslaw B. Kowalczuk

Froth flotation is widely used for upgrading of ores and other materials. Efficiency of flotation depends on many parameters, including type, chemical structure and dose of flotation reagents. Selection of a proper frother in flotation depends on the material used, necessary dose of frother and its selectivity. The selectivity of flotation can be characterized by proper separation factors and indices. In this paper separation selectivity and power of frothers were evaluated basing on separation data for a given material and frother, plotted as the recovery of the useful component in the concentrate versus the recovery of the remaining components in the tailing. Such a plot is called the Fuerstenau upgrading curve. The selectivity was defined as the location of the whole upgrading curve in relation to no and ideal separation lines, expressed on the scale from 50 (no separation) to 100% (ideal separation). In turn, the flotation power was defined as the dose of frother to reach a certain upgrading level at which recoveries of the useful and unwanted components are equal. The power and selectivity of frothers were determined for the Kupferschiefer stratiform copper ore floated in the presence of a fixed amount of xanthate and varying doses of frothers using a laboratory flotation machine. Basing on the separation results for different poly(propylene glycol) (CnH2n+1O(C3H6O)mH, CnPm) and poly(ethylene glycol) (CnH2n+1O(C2H4O)mH, CnEm) alkyl ethers, it was found that the concentrate yield and recovery of copper as the useful component in the concentrate were greatly influenced by the type and dose of frother. However, the same results plotted in the form of the Fuerstenau upgrading curve clearly indicated that the selectivity of frothers was similar, while their power was different. It proves that both selectivity and power of frothers are useful parameters for characterizing flotation systems.

Jan 1, 2016

By S. Heusermann, S. Fahland, J. Behlau, A. Schäfers, J. Hammer

In the course of the deep subsurface use, the Federal Institute for Geosciences and Natural Resources has been carrying out extensive geological and geomechanical research and practical project work on domal salt structures, to prove their suitability e.g. for the disposal of radioactive wastes. Recent work on disposal sites has been taking into account the 3-D geological and geomechanical modelling of the underground structures. The geological models are generated using the special-construction openGEOTM code to improve the visualisation and interpretation of the geological data basis, e.g. borehole, mine, and geophysical data. For the geomechanical analysis of underground structures the JIFE finite-element tool has being developed to analyze large 3-D structures and to consider coupled THMC processes. The results of finite-element calculations, i.e. stresses, strains, displacements, and dilatant zones, are basic values for the evaluation of the stability of the structures and the long-term integrity of the geological barrier. As an example, the results of geological and geomechanical investigations of the Morsleben repository are presented including three-dimensional modelling of the entire geological structure of the central part of the mine as well as three-dimensional geomechanical model calculations to provide the necessary results for a long-term safety prediction.

Jan 1, 2015

By R. B. Harkness

Many of us are familiar with the history of oil in the Province of Ontario, but for the benefit of those who have never heard the story I will repeat it. In 185 7 J. H. Williams, of Hamilton, an old-country Scotchman, who had the advantage of experience gained from the primitive methods used for refining the oil collected at seepages in Roumania, heard of the "gum beds" along Black creek in Enniskillen township, Lambton county. He erected a small plant in the bush and refined illuminating oil, where the village of Old Springs now stands. The labor of collecting this thick ?gummy substance from the sluggish water of the creek, prompted him to dig a well, the next year ( 1858), in the hope of obtaining a greater quantity. When his excavation reached a gravel bed on top of the rock, oil, resembling "lubricating oil of commerce", rose several feet. Several of these wells were dug and his refining business flourished. The following year the Drake well, in Pennsylvania, was drilled into rock, resulting in an oil find which encouraged one James Shaw to make a similar attempt on Black creek. With a spring-pole drill he completed his well in the spring of 1861 to a depth of 160 feet, and at that depth struck a gusher that flowed uncontrolled for several days. Great excitement followed and the village of Oil Springs had a mushroom growth. The Petrolia field was discovered in 1865. Lick followed up the Thames with a spring-pole rig testing the formations along that river and discovered the original Bothwell field in 1865. During the sixties wells were drilled in many counties in southwestern Ontario.

Jan 1, 1924

By G. Vibert Douglas

Introduction A preliminary paper dealing with the subject of ore-shoots was presented to this Society at its Annual Meeting last year (1). The present paper records the attempts which have been made during the interval to further this study. In reporting this work, I wish to state that I do not consider the investigation complete; many more experiments will have to be carried out, and more field data will have to be recorded, before the geologist can say with confidence an ore-shoot should start at this point and pitch in that direction. The aim of these experiments is to find some criteria which will serve the mining engineer and mining geologist concerned with ore-shoots in hydrothermal veins.

Jan 1, 1935

By Hyumng Sup Choi

The role of the interfacial electrical 'Condition on the adsorption of col-lectors on mineral surfaces has been studied by electrophoretic mobility and adsorption measurements made on zircon. From the investigation of the electrokinetic properties of zircon, H+ and OH-are seen to act as potential determining ions, thus controlling the electrical nature of this mineral. The isoelectric point of zircon occurs at a pH of approximately 5.0, and it is evident, therefore, that the zircon surface would be positively charged below a pH of 5.0 and negatively charged above this pH. The adsorption of collectors therefore de-pends strongly on the pH of the solution; anionic collectors are adsorbed on positively charged surfaces and cationic collectors on negatively charged surfaces. This, in turn, de-fines the effective flotation condition, with respective collectors, for this mineral. The above results have been correlated with the flotation behaviour obtained by the simplified flotation test using a modified Hallimond tube.

Jan 1, 1963

By A. -M. Cadieux

During the geological synthesis of the Réservoir Pipmuacan area (NTS 22E) by the Ministère des Ressources naturelles (Québec), several ilmenite-apatite occurrences, some well-known and some recently discovered, have been examined. These occurrences are hosted in the Lac-Saint-Jean and Labrieville AMCG anorthositic suites. The Lac-Saint-Jean Anorthositic Suite (1160-1140 Ma), composed of multiple intrusions covering an extensive surface area, is characterized by labradorite plagioclase. The Labrieville Anorthositic Suite (1010-1008 Ma) is characterized by andesine plagioclase. It was previously known as the Labrieville Anorthosite, which was composed of a small isolated pluton located east of the Lac-Saint-Jean Anorthositic Suite. However, new geochronological data and field observations indicate that the Labrieville Anorthositic Suite in fact includes several intrusive bodies, namely the La Hache Monzonite and the Mattawa Anorthosite. A series of major structures (Saint-Fulgence, Pipmuacan, and Chute-des-Passes deformation zones) and their conjugate faults played an important role in the emplacement of the Lac-Saint-Jean Anorthositic Suite. The Saint-Fulgence deformation zone appears to have been involved in the emplacement of the Labrieville Anorthositic Suite. Oxide mineralizations are abundant in both anorthositic suites. Ilmenite, magnetite (± titaniferous), and apatite assemblages are found mostly in the labradorite-type anorthosites, while hemo-ilmenite, magnetite and apatite assemblages are associated only with the andesine-type anorthosites. Field works has revealed ilmenite-apatite mineralizations in a variety of settings, with grades reaching 48% TiO2, 16.2% P2O5, and 71.7% Fe2O3 (tot). Numerous oxide-bearing gabbronorites, often accompanied by or located near massive apatite-oxide accumulations (nelsonites), were discovered. Among these oxide-rich zones, breccia zones with anorthosite enclaves in an oxide matrix (ilmenite-magnetiteapatite) have been observed. Locally, ilmenite-apatite mineralization occurs as cumulate concentrations in ultramafic rocks. Evidence has been observed for immiscible magmas, for magmas differentiated from a mangerite or jotunite parent, and even for late magmas differentiated from the anorthosite magma itself (apatite-bearing anorthosite). Finally, the northern part of the Lac-Saint-Jean Anorthositic Suite hosts sulfide and vanadium mineralizations associated with ilmenite-apatite enriched zones, with grades reaching 1.48% Cu, 1.22% Ni, 1.6% Cr2O5, 0.25% Co, and 0.52% V2O5.

May 1, 2003

By Evelynn Stirling

"The paper/presentation will review the evolution of diesel technology from older diesel engines (1990 vintage) through to the latest technology as a result of the ever changing emissions regulations. It will encompass the EPA Tier levels as well as the latest Euro Stage V emissions. The next step with technology will be to address the CO2 emissions, which translates to improving fuel efficiencies of the product as well as other technologies like battery electric, hybrid and fuel cells. As technology progresses it also becomes important to improve connective diagnostic systems to support maintenance practices and improve efficiencies. What will also be presented will be the key emissions changes to the different gaseous and particle mass elements as the products have transitioned from the EPA Tier 3 through to Tier 4 Final regulations. Offering a range of different technologies to the underground mining market matters as not all pieces of equipment will perform optimally due to its duty cycle and application. INTRODUCTION Rudolf Diesel built his first well-known prototype of the high-compression engine in 1897. Since that time, the diesel engine has evolved into one of the world’s most capable and reliable forms of power generation. Diesel engines can be found in a wide variety of vehicles and equipment, powering everything from agriculture and construction equipment to power generators and marine vessels. In the early days the emissions from diesels was very poor and extensive work has been accomplished over the decades to make the product more environmentally friendly. This is more important in underground mining where the space is limited and ventilation is expensive and challenging. DISCUSSION The key driver of the development of diesel technology is the legislation globally around engine emissions. The emission level requirements over the years has forced diesel engine manufacturers to build a deep technical understanding of the system and how to innovate and optimize key elements of the engine. Cummins expertise has been built over the years as the diesel engine has evolved from a relatively simple mechanical engine to an electronic system with advanced air handling, fuel system, after treatment, and controls. Cummins has also continued to expand into systems beyond diesel, including natural gas. Many new components have been added to diesel engines to reduce emissions while improving fuel efficiency and reliability and, at the same time, reduce the total cost of ownership to the customer."

Jan 1, 2019

By N. Bahrani

Knowledge of the state of stress in the Earth?s crust is very important to the safe and efficient development of underground excavations in mining and civil engineering projects. A number of methods have been developed over the past 40 years to assess the stress field in the rock mass. These range from local estimates derived from compilation of regional stress databases to back-analysis of field observations to dedicated in situ measurements. The Geomechanics Research Centre (GRC) at MIRARCO has a long history of undertaking in situ stress characterization and measurement. In this paper, the stress measurement techniques used by the GRC, including overcoring and undercoring in addition to borehole breakout back-analysis, are briefly reviewed. The limitations and application of each technique for different ground conditions and the challenges involved during the field work and in interpretation of the results are discussed. A successful stress measurement campaign is not limited to acquiring valid local measurement, but must include a careful interpretation and integration of the measurement with other geological and geotechnical context information. Based on our experience, it is suggested that all available stress indicators and data are combined and integrated with the local geological and geomechanical conditions to derive a consistent stress characterization for a given site.

Aug 1, 2013

By Geo. D. Furse

"The information that has accumulated regarding the geology of the McIntyre mine is the result of work by several geologists and, as might be anticipated, their conclusions have varied. The writer has been at the mine only a few years and due to wartime conditions has not been able to study and review the mine's geology as thoroughly as his predecessors. Where the writer's conclusions differ from those of previous authors, it should be noted that he has been unable to re-map all the workings in which flow contacts are exposed, but has endeavoured to describe the structure as indicated by the evidence he has been able to observe. He wishes to thank H. G. Skavlem and H. S. Robinson for their constructive criticism of this paper, and McIntyre Porcupine Mines, Limited, for permission to present it. A list of references is appended.The McIntyre mine is in the central part of the Pearl Lake section of the Porcupine gold area. It includes the ""bed of Pearl lake, twenty-two claims to the north of the lake, and the Platt Vet lot to the southeast. It is bordered on the west by the Hollinger and on the east by the Coniaurum property. The chief ore-bearing veins on the upper levels lie very close to the north shore of the lake, but some occur under the lake, and others of lesser importance are found to the southeast. The most important veins are Nos. 3, 5, 7, 10, and 25. Some of the veins extend into the Hollinger. on the west and others cross the east boundary into the Coniaurum. The total production since the commencement of milling in 1912 to the end of March 1947 has been $168,448,218 in gold and silver from the milling of 17,690,963 tons of ore."

Jan 1, 1954

By Jochen Franke, Matt Bird, Thoma Perkins, Malcolm Powell, Jason Robertson, Paul Toor

zThe operation of SAG mills is variable over time due to their continually changing liner shape, mass and subsequent load motion. However, this tends to be poorly accommodated in liner design and mill control, with only limited compensation made for this influence, usually in the first few weeks after a new liner is installed. With ever-increasing ore competency, increasing energy costs and decreasing ore grades, simplified design and operational approaches that compromise the achievable mill efficiency are no longer adequate. This paper presents a methodology that has been developed to measure and account for the changes in mill performance as the liner wears. This involves monitoring all liner profiles – in other words the three-dimensional liner shape - over the life of the liner, then conducting controlled surveys at different stages of the liner wear life, and correlating the mill performance to the liner profiles. The measured liner mass is modelled to provide an ongoing meaningful load mass measure that excludes the liner mass.

Jan 1, 2012

By F. P. Hassani, M. Hefni, M. F. Kermani

"This study is part of large and an ongoing investigation into the development of a light-weight and highly fluid mine fill for various applications in mining and civil operations. Foam mine fill is the new material proposed for backfilling mines, and is fabricated by mixing stable foam into a mixture of tailings, binders, and water. This paper investigates the effects of both binder dosage and the amount of foam used upon the mechanical and physical properties of foam fill, mainly in regards to compressive strength, porosity and density.Samples were prepared using tailings from a copper mine as the inert material, Normal Portland Cement as the main binding agent, and a foaming agent with a foam generator. Samples were cured for 7, 14 and 28 days and were then subjected to unconfined compressive strength (UCS) testing. Select samples were subjected to mercury intrusion porosimetry, so as to study the microstructural properties. An empirical model was then developed, using a response surface methodology to establish a relationship between the investigated parameters. INTRODUCTION AND BACKGROUNDThe disposal of mine tailings is a significant issue in the mining industry, particularly as mine production increases. Many mines re-use mine tailings for backfilling, which is a method for reducing environmental exposure to tailings, maintaining underground stability, and increasing ore recovery (Benzaazoua, Belem & Bussière, 2002).This paper introduces a new type of backfill called ‘foam mine fill’. This proposed backfill material is similar to cellular concrete, as air bubbles are entrained in cement or lime mortar, resulting in a cellular structure (Narayanan & Ramamurthy, 2000). Air voids can occupy up to 70% of the volume of concrete, which makes it light- weight, and thus can be used for a wide range of civil applications, including backfilling (Tarasov et al. 2010; Panesar, 2013). Unlike cellular concrete, the incorporation of air bubbles into a mixture of tailings, binder and water makes foam fill a potential new backfilling material. Furthermore, a preliminary investigation on foam fill samples found that pulp densities should be optimized before adding the foam, in order to produce consistent samples without foam segregation or losses (Hefni et al., 2014)."

Jan 1, 2015

By R. E. Evans

This paper contains an analysis of the geography and geology of the Black Lake area, Eastern Townships of Quebec, an outline of the work to be performed, an explanation of the design concept and how it was developed, and a discussion of the actual stripping operation, including details of the machinery being used, etc.

Jan 1, 1967

By S. Z. R. Pinkney

Positron Emission Tomography (PET) is a medical technique that produces three dimensional images of the body, commonly to aid diagnosis and treatment of tumours. PET has been developed by the University of Birmingham in order to track particles in an opaque system which is known as Positron Emission Particle Tracking (PEPT). The object to be tracked is irradiated. As the radionuclide decays positrons are produced; when these collide with electrons a pair of concurrent parallel back-to-back gamma waves are emitted and detected, from which the position of the object can be calculated. Stirred media mills are used for particle size reduction. The mill is usually operated at high solids loading with grinding media and has a polyurethane or polyurethane-lined steel pot and is thus opaque. For this study grinding media has been directly irradiated and tracked using the PET camera during the grind. The stirred media mill can be divided into cells of equal volume known as voxels. The fraction of the total time the irradiated media spend in each voxel can be shown in an occupancy diagram. The mean velocity and kinetic energy of the media for each voxel are calculated and also plotted. In occupancy and kinetic energy plots colour indicates the value of the voxel, in dimensionless time and Joules respectively. The arrow in velocity plots shows direction and length of arrow indicates magnitude of the mean velocity for the voxel. From these diagrams and further data analysis a detailed understanding of the flow patterns, media behaviour and high energy areas of the mill can be developed. Variables considered were the tip speed of the impeller and density of the grinding media. It was found that the grinder has three distinct regions: above, at and below the impeller with each region having its own flow patterns and velocity and kinetic energy profiles. These are different for each variable and so are used to characterise the grind. Tip speed and density of the grinding media were shown to both affect the velocity of the media and the proportion of time spent in the each region of the grinder.

Aug 1, 2013

By N. Chow, W. McCombe, G. Remple, J. Nikkari, L. Nightingale-Mercer

Orano Canada Inc. (Orano) operates the McClean Lake mill in northern Saskatchewan, processing high concentration uranium ore, delivered in slurry form, from the Cameco operated Cigar Lake mine. This slurry is ultimately processed into the purified uranium oxide product known as calcined yellowcake. During the calcining process, sulphate (SO42-) entrained in the yellowcake undergoes thermal decomposition into sulphur dioxide (SO2). SO2 is a colourless gas that poses health and safety risks. Since 2016, an anhydrous ammonia dosing system was successfully added to the existing Venturi particulate scrubber system to provide efficient removal of SO2 from the calciner off-gas. Within the pH controlled scrubber solution, SO2 exists in a pH dependent equilibrium with sulphite/bisulphite (SO32-/ HSO3-). The presence of a significant fraction of reduced sulphite and bisulphite in mill solutions presents a hazard in downstream circuits. Should these solutions drop in pH, either through natural oxidation or inadvertent mixing with low pH solutions, the solution equilibrium will shift from SO32-/HSO3- in favour of SO2, resulting in the evolution of SO2 gas from any liquid surfaces. In 2018, Hatch Ltd. (Hatch) and Orano implemented a design change in the calciner scrubber system. Blowdown from this system is now treated in an oxidation pre-step utilizing hydrogen peroxide (H2O2) and anhydrous ammonia (NH3) for pH control, in order to convert the residual sulphite/bisulphite present in solution to stable ammonium sulphate product. This paper will detail some of the challenges and actions undertaken to minimize SO2 risk, culminating in the recent introduction of a novel system designed to oxidize sulphite/bisulphite and prevent mobilization from the calciner scrubber solution into other mill areas where there is the potential for acidification and SO2 release.

Jan 1, 2020

By F. Hosseini

Shaping of metals by thixoforming relies on the unusual flow behavior of semisolid slurries containing nondendritic solid phase. The Flow behavior of metallic alloys containing both solid and liquid phases is investigated in the low solid fraction range (, 55%). This behavior depends on both the solid fraction and the shear rate. Four different shear rates is applied using back extrusion technique and flow stress versus true strain in different solid fraction is compared. It is well accepted that the flow stress s of alloys in their semi-solid state obeys to a thixotropic behavior, due to agglomeration and dissagglomeration phenomena during forming. The load-displacement curves produced from the tests may show an initial peak, believed to originate from a skeletal structure which rapidly breaks down under shear. Apparent viscosity obtained from this method is compared with other works and the proper power law of pseudo plastic state is introduced.

Oct 1, 2011

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By Kilmar Mine

The Kilmar dolomitic magnesite deposit~ in sourhwesr Quebec lie in Grenville Province sedimentary rocks that strike north and dip steeply west. The sediments comprise quartzitic, carbonate and argillaceous members. The middle or carbonate member hosts the magnesite and, like the two other members, has been intensely mewmorphosed. Magnesite occurs as lenticular shaped zones of altered limestone and is mixed with 5 to 30% dolomite crystals. Diopside, serpentine and mica are common accessory minerals. Magnesite appears to have formed from merasomarism of all or part of the carbonate member due to intrusion of hot magnesia-rich solutions. Magnesite is mined from a 490 m vertical shaf1 and is milled and burned into clinkers, which then are shipped 10 pyroprocessing industries around the world.

Jan 1, 1984

By B. K. Mishra, Subrat Kumar Padhy, B. C. Tripathy, I. N. Bhattacharya

Manganese is a difficult metal to electrodeposit due to its high electronegativity and continues to possess unique process challenges. Manganese deposits of high quality are electrodeposited on 316 grade stainless steel from sulphate solutions in the presence of organic additives such as tetra ethyl ammonium bromide (TEABr), tetra propyl ammonium bromide (TPABr), and tetra butyl ammonium bromide (TBABr). The concentrations of these additives were examined over a relatively broad range to evaluate their effect on current efficiency, specific energy consumption and deposit morphology of the electrodeposited manganese metal. A maximum current efficiency of 68% was achieved in the presence of TEABr in the bath. X- ray diffraction studies revealed that (330) (411) planes were the most preferred planes of crystal growth during manganese electrowinning at a current density of 500 A/m2 resembling alpha-manganese irrespective of the nature of additive. Scanning electron micrographs showed smooth and uniform deposit morphologies when manganese was electrodeposited in the presence of TEABr.

Jan 1, 2014

By H. M. Woodrooffe

This paper deals with the laboratory facilities at the Mines Branch for carrying out research in the industrial minerals field, and also reviews current programs in ceramics and construction materials, in non-metallic minerals and in the milling of industrial minerals. It then discusses the application of these pro-grams to industrial problems.

Jan 1, 1967