Search Documents

By G. Thom, A. Kay, J. B. Hyde

"This paper will initially outline the specific types of copper castings used in blast furnace iron production. Tuyeres, tuyere coolers and stack cooling plates will be discussed in some depth, with particular reference to their dimensional configuration and purpose.Following this, the failure of such cooling members will be discussed, with special focus on tuyeres. Tuyeres are the most common casting which often requires replacement. Reasons for failure and its effect on operations will also be included.The latter sections of the paper will deal with the strict specifications demanded by ironmakers regarding copper castings. The justification for such rigid demands will be explained through the material presented earlier in the paper.IntroductionThe modern 5000-tpd blast furnace, worth millions, is a large capital investment to be sitting idle. Consequently, ironmakers strive to minimize the loss in iron production and revenue from furnace downtime. Two major causes of downtime are furnace relines and shutdowns to replace damaged tuyeresor tuyere coolers. Copper ancillaries are important items in the production of iron. They are consumable items, therefore they contribute to the campaign life or to the downtime in blast furnace production.Several combinations of lining and cooling systems have been used with varying degrees of success. Blast furnace refractories have evolved from ceramic to carbonaceous linings. The Russians and Japanese have successfully introduced stave-cooled furnaces that may have several forms, such as evaporative cooling. Stelco has two furnaces which use the Russian-designed cast iron system. However, this paper will be confined to the use of copper cast cooling members in a conventional internally cooled furnace.Figure 1 is a schematic cross section of the E blast furnace. The three major sections of a blast furnace-the stack, bosh and hearth-are identified. Further, the locations of the various copper members are indicated. This furnace produces an average of 5300 tons of hot metal per day."

Jan 1, 1982

By F. D. Forgeron

"ONE OF THE FIRST DOCUMENTED APPLICATIONS of soil geochemistry in the Canadian Shield was that carried out by Chisholm in the Kenora district in 1949. This survey proved successful in outlining sulphide-associated gold veins utilizing cold-extractable metals. Since then, mining companies, government agencies - both provincial and federal - and universities have conducted soil investigations. Some of the results are documented in publications, others are on open file in provincial and federal mines departments and, unfortunately, many other investigations with both successful and unsuccessful results are buried in company files or have been discarded. This paper deals with soils within the scope of chemical studies of overburden in the Canadian Shield. The subject is a broad one and some definition is required. The soil investigations discussed herein are those aimed at the testing of specific targets more or less in the source area. This definition distinguishes soil investigations from other overburden studies which commonly monitor metal accumulations at some substantial distance from the metal source. Naturally this distinction is relative, because in many instances there is overlap."

Jan 1, 1971

By John R. Craynon

Science and Sustainable Development Each of the ?pillars? of sustainable development are directly impacted by mining. We need science to understand exactly how mining contributes to each. Overview of presentation ? History of mining and sustainable development ? Role of stakeholders in measuring/accepting contributions of mining to SD ? Identified ?shortfalls? in understanding mining and SD ? Science needs

Aug 1, 2013

By R. P. van Hille, A. W. van Zyl

The BIOX® culture, aiding liberation of arsenopyrite/pyrite occluded gold, is inhibited by thiocyanate (SCN > 1 mg/L); precluding the recycling of tailings water up-stream of the bioleaching circuit. The activated sludge tailings effluent remediation (ASTERTM) process is a biological process that was developed to facilitate water recovery and treat waste water on-site (to achieve a SCN concentration < 1 mg/L) to be recycled or disposed of. The aim of this study was to investigate the effects of changing temperature and SCN loading on the SCN degradation ability of the mixed microbial population clue to seasonal temperature changes and fluctuations of SCN concentration in the waste water.

Jan 1, 2011

By Barun Gorain, Andy Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimisation of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimisation, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterise cell hydrodynamics, gas dispersion properties, fioth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimisation of the Red Dog flotation circuit.INTRODUCTIONThe traditional methodology for flotation scale-up and plant design is based on the rule-of-thumb with safety factors, dimensionless hydrodynamic group similitude considerations, etc. With the recent trend towards larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-of-thumb and trial-and-error, then the probability of failure would increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimisation of the circuit to meet its metallurgical target. This results in a plant design incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2002

By John R. Goode

"The year 2011 witnessed a major surge in rare earth prices as China, supplier of +95% of the world’s rare earths, reduced export quotas and increased export taxes and duties. In response, companies around the world are scrambling for alternative sources. In Canada too, there is a race to be the “first” rare earth producer. Something that is not generally realized is that Canada has a long history of rare earth production and was a major supplier from the early 1960’s to 1990. At one stage, Canada was said to be supplying more than one third of the world’s yttrium and probably supplied even more than that. Five decades ago, thorium was a key element in many non-nuclear applications and Canada became a major supplier of thorium from the late 1950’s to 1968, first as a by-product of uranium and then as a co-product of rare earths. This paper reviews the development of Canada’s original rare earth and thorium production facilities, which were located in the Elliot Lake uranium camp in Northern Ontario. The uses of these elements, geology, mineralogy, markets of the time, and processing are all discussed. Some of the lessons learned from these pioneering operations might be useful in today’s race to develop the next generation of rare earth production plants.INTRODUCTION The rare earths and thorium were first identified in the early 19th century but were little more than curiosities for the next century. However, in the mid-1960’s the invention of rare earth-based phosphors for the cathode ray tube in colour television sets launched a major demand for certain rare earths. The use of thorium as an alloying agent in aircraft and missiles grew rapidly in the late 1950’s. In the same period, demand for uranium for both weapons and power production soared. Also in the late 1950’s, the Elliot Lake uranium-thorium-rare earth deposits (also known as the Blind River deposits) were discovered. This conjugation of events led to uranium production in the Elliot Lake camp, quickly followed by the co-production of thorium and, later, the rare earths. Uranium production in the Elliot Lake camp continued from 1955 to 1996. Thorium was produced continuously from 1959 to 1969. Rare earths were produced, intermittently, from 1965 to 1990. Complete production records are not readily available for thorium and the rare earths but unquestionably Elliot Lake production made a significant contribution to world production. This paper is intended to present as much of the information that is available."

Jan 1, 2012

By T. Deng

Flotation of rare earths is complicated by the number of mineral classes that carry rare earth elements, including carbonates, phosphates, and silicates that often co-occur within the same deposit. Gangue constituents often belong to the same mineral classes as the rare earth minerals themselves. Chemical regimes developed for specific separations employ customized combinations of collectors, modifiers, and depressants that are not directly translatable to other operations. In this rougher flotation case study, a reagent suite including phosphate ester and sulfosuccinamate, originally developed for the recovery of bastnasite and monazite from silicate hosted ore, could not be applied to a synchysite ore hosted in carbonate gangue because the suite was aimed at silicate gangue rejection only. The separation of a fluorocarbonate mineral from carbonate gangue required a different chemical regime involving the use of hydroxamate and sodium silicate. Maximizing rare earth recovery was complicated by the presence of slimes. The effect of desliming and the increase in grind size was explored.

Jan 1, 2014

By The Honourable George Prudham

"I AM PLEASED indeed to be present with you here today and to be taking part in the proceedings of your convention. You have been greeted and welcomed to the Province by Premier Manning who is also provincial Minister of Mines and Minerals, and to this City by Mayor Hawrelak. As Minister of Mines and Technical Surveys in the federal government and as Member of Parliament for Edmonton West, I have been asked to share the honour of extending greetings and a cordial welcome to all.It is a happy coincidence that this representative national gathering, indicative of the growing strength and significance of a great basic Canadian industry, is taking place in the Macdonald Hotel, the new addition of which marks another important step forward in the progress of this City and district.This happens to be the third national convention of the C.I.M. that I •have had the pleasure of attending and I trust that I am not presumptuous in expressing the hope that I will have the opportunity of attending many more conventions of the Institute in my present capacity.Dr. Kidd has bestowed on me a high honour by asking me to be Co-Chairman of this Inaugural Session of the Convention and thus to share with him the responsibility of presiding over the proceedings of this afternoon."

Jan 1, 1953

By D. W. Hendriks, C. Daoust, K. V. Konigsmann

"The concentrator of Mattagami Lake Mines Limited commenced operation in 1963. It had been designed with instrumentation proven at that time. New control techniques were added in subsequent years.An on-stream X-ray analyser was installed in 1968. It provided circuit analyses for six years without the aid of a computer. In late 1974, control of the flotation circuit by computer was incorporated into the system. Flotation efficiency improved considerably, zinc"" recovery increased by one percentage point and concentrate grade by four-tenths of a percentage point. Reagent costs decreased modestly through reduction of copper sulphate consumption."

Jan 1, 1976

By Dominic Fragomeni

"The mineral processing industry has had a long history of innovation that is recognized but not often celebrated. These include significant advances in mineral measurement, testing, comminution, mineral separation and process control technologies that have transformed mineral assemblages into ore.This presentation presents some of the major mineral processing innovations and the impact they have had on our industry. As we look to the future, it is critical that we innovate and change. We will explore some examples of the next developments and how they can be catalyzed in the face of risk management, lower metal price cycles, resource constraints, inertia and the challenge of short term value delivery."

Jan 1, 2017

By P. A. Riveros, J. Binvignat, V. M. McNamara, D. Koren

The recovery of cyanide from a gold mill solution containing high levels of copper (400 mg/L to 900 mg/L) using the AVR process was evaluated. It was determined that acidification to pH 2 to 3 provides a suitable balance between HCN generation, copper precipitation and acid consumption. A short pilot plant campaign showed that ~75% of the feed WAD cyanide was recovered while the remainder precipitated along with copper upon acidification. The acid consumption averaged 3.5 g H2SO4 per litre of solution. The copper precipitate, consisting mostly of CuCN and CuSCN, was readily separated from the solution by gravity. The volatilization of HCN in countercurrent packed columns averaged 98.7% efficiency. Reabsorption of HCN was practically 100% in NaOH solutions and slightly lower in a lime slurry. Basic volatilizer design parameters applicable to a large-scale operation were determined, including the Henry’s Law constant and the mass transfer coefficient of HCN gas.

Jan 1, 1998

By E. I. Robinsky

"This paper describes a new, proven approach for tailing disposal. Not only is the disclosed system less damaging to the environment, it is also less costly to operate, to close down and maintain in perpetuity. The basic concept is to discharge thickened tailing from one permanent location.This creates a conical or hill-like deposit which:(1) requires lower perimeter dykes for equivalent storage capacity;(2) eliminates decant towers and decant lines;(3) requires no steep dams built of tailing;(4) is stable:(5) requires only a small pond outside the deposit;(6) decreases pollution of the surrounding environment by water seepage and deflation; and(7) simplifies abandonment and ""closing-down"" operations.The approach is made possible by the fact that, at a sufficiently high ratio of solids to water, tailing material can be made to accumulate at slopes of 5 or 6 per cent -- considerably steeper than possible by traditional methods using low solids-to-water ratios. To achieve the necessary solids-water ratio (35 to 60 per cent), it may be necessary to install a thickener. It is expected, however, that at many concentrators it may be possible to discharqe relatively clear plant water through a line separate from the tailing line, thus reducing the load on the thickener."

Jan 1, 1976

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments. A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including respectable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects. Reflecting the observation of a wide range of views regarding the subject of inflation, this paper will-address the impact of five different approaches to inflation on the evaluation of a single Canadian mining project."

Jan 1, 1987

Strategic Branding ? In 2006 Explore for More was created ? By industry, for industry ? Cohesive approach to career attraction ? Defines industry and employers of choice Career Kits ? Positive impression of mining: ? before seeing the brochure 31% ? after seeing the brochure 83% ? Likely to consider a career in mining: ? before seeing the brochure 12% ? after seeing the brochure 23% MARS ? Mining Attraction, Recruitment, and Retention Strategy (2007-2010) ? Attract, recruit and retain a skilled workforce ? Increase participation of under-represented groups ? Dispel myths and misconceptions of the mining industry ? Inform and educate Canadians of career opportunities ? Promote and build upon industry best practices in workforce planning

May 1, 2009

By R. H. Pemberton

"THE Mattagami district of Quebec has, during the past few years, experienced intense exploration by virtually every mining company operating in Canada. As a result of this activity, a number of well-mineralized zinc-copper bearing bodies have been found, some of which will almost certainly go into production. Much of the area has undergone what is now termed ""Saturation Prospecting"" or intense and detailed geological and geophysical surveying, followed by the drilling of nearly all possible bets. Considering only the airborne geophysical surveying, some blocks of ground have been flown by virtually every geophysical instrument which has to date been installed in an aircraft. A list of these different geophysical instruments would include: l. Fluxgate-type total field magnetometers 2. Vertical field magnetometer ,3. Nuclear-precession magnetometers 4. Single-frequency out-of-phase electromagnetometers 5. Dual-frequency out-of-phase electromagnetometers 6. Horizontal component measuring electromagnetometers 7. In-phase and out-of-phase electromagnetometers8. Dip-angle measuring electromagnetometers."

Jan 1, 1961

By Sanjiv Dhanjal

"Often mineralogy dictates the physical properties of a material rather than chemistry. This in turn affects how that material behaves in a process plant, and whether optimum conditions for refining one mineral are different to those for refining another. For example how does refining copper from chalcopyrite differ to refining copper from bornite?Minerals are naturally occurring inorganic solids that have a definite chemical composition and an ordered atomic (crystalline) structure. X-ray diffraction is a common and highly developed method to identify and quantify minerals. X-rays are fired onto a material and the mineral is identified by the angles where the diffracted X-rays are in phase.Most X-ray analyzers are laboratory based. A sample is prepared and analyzed by a detector that travels in an arc to collect the diffraction pattern. COSMA has a curved detector which picks up the complete x-ray pattern instantaneously. Therefore, material is collected and transported through the machine where is it is analyzed continuously.COSMA measures about 0.5 tons of material per day, while laboratory analyzers measure a few grams at a time. Real time data trends are produced allowing for improved process evaluation and automatic control. The COSMA on-line system has taken X-ray diffraction out of the laboratory into the field.There are a number of systems in operation in cement production. It is recognized that on-line mineral analysis has a role in many other processes. This paper presents the technology and invites further discussion should the technology be beneficial to members of the audience.INTRODUCTIONThis article describes COSMA, a system that provides direct and continuous on-line mineral analysis using X-ray diffraction in the field. While X-ray diffraction is a common technique used in mineral analysis, the time from sampling to analysis can be hours and plant operators typically do not get the data in time to control a process or respond to an upset. COSMA provides rapid measurement, analysis and feedback of data, in real time. This provides powerful information that can be used to optimize operation, thereby reducing costs and increasing quality."

Jan 1, 2009

By B. Lueger, D. Shen, M. Sedighy, R. Rand, R. Saleh, J. Cheung, M. Rifai, I. Khan, W. Sauri, D. Setianto

The world’s first active power demand stabilization system for a 3-electrode electric arc smelting furnace was commissioned at PT Vale Indonesia in December 2012 on Furnace No. 2 using an SPLC (Smart Predictive Line Controller). The SPLC technology in combination with the Furnace No. 2 rebuild and other upgrades has enabled PT Vale to increase the electrical input to the furnace by up to 20% on a stable and sustainable basis by eliminating peak powers that overload and trip out the electrical equipment, and by reducing power unbalances. The SPLC technology maintains smooth arc power using a continuously variable thyristor controlled series reactor. The SPLC compensates variations in the furnace arc with predictive changes in the circuit reactance at a speed of up to 60 times a second. The system started up quickly and has been shown to be easy to operate and maintain by PT Vale. PT Vale’s Operations Team has been testing the new system at set points of up to 90 MW on the newly re-built Furnace No. 2. Over the last 12 months, the throughput of Line 2 has increased by approximately 10% on an annual average; however, debottlenecking in other design areas of the operation is required in order to achieve 90MW operation on a sustainable basis. This outstanding success results from a combination of the furnace and other upgrades, the SPLC active power stabilization, and the skill of PT Vale in quickly adopting new technologies and maximizing the combined benefits of each technology in their operation.

Jan 1, 2014

By E. Wasmund

"Sandfire’s DeGrussa Copper-Gold operation in West Australia is a new high grade copper sulfide mine, which includes a 1.5 Mtpa concentrator which was completed in 2013.Early after commissioning, it was identified that the flotation capacity in the all-mechanical cleaner circuit was not sufficient. In order to improve recovery, the tail from the cleaner scavenger was sent back to feed the rougher scavengers. Test-work was done on-site to evaluate the possibility of using a flotation column as a pre-cleaner. A CavTube™ sparging system was selected, which is especially effective for fine ore particle flotation. Test-work was conducted at site using a 150 mm diameter unit, and then confirmed on a 500 mm diameter unit. A 4250 mm diameter full scale unit was installed in Q4 2014 and commissioned in Q1 2015. This unit gave some significant advantages including a reduction in re-grinding requirements, elimination of a circulating load and increase in the recovery of copper in the cleaner circuit and overall circuit.In this presentation, the benefits of columns and cavitation sparging for floating fine particles and rejecting fine entrained gangue will be explained. Also, the results from a lab unit and a pilot unit will be compared against the results of the full-scale unit. The paper will demonstrate the scalability of flotation columns, and which phenomena and scale-up criteria must be considered to be successful. Finally, some general observations will be made about the importance of columns in copper cleaning circuits.IntroductionSandfire Resources’ DeGrussa copper-gold concentrator is located approximately 900 km north-north-east of Perth in Western Australia. The project area landscape is scrubby mulga lands with few notable features. The climate is arid with high temperature and heavy summer downpours."

Jan 1, 2016

By M. Maldonado, J. A. Finch

"A flotation bank consists of a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three strategies for optimizing bank performance: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data is analyzed in respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.INTRODUCTION Flotation is used to separate valuable minerals from each other and from gangue. To reach a target metallurgical performance, usually assessed in terms of concentrate grade and recovery, feed is passed through stages such as roughing, cleaning and scavenging. All these stages comprise serial arrangements of flotation cells known as banks, lines or rows. Although a bank is the simplest interconnection of cells in a circuit, i.e. the tails of one cell is the feed to the next cell down the bank, how to operate each flotation cell in a way that the whole bank performance is optimized remains a challenge. Significant efforts have been made towards understanding the effect of operating variables on the flotation performance of an isolated cell (Lynch et al., 1981; Finch and Dobby, 1990; Gorain et al., 1998). However in the case of banks the variables that can be manipulated increase with the number of cells in the bank and the problem of how to manipulate them to achieve optimum performance is difficult even disregarding variation in ore characteristics (Lynch et al., 1981, p. 16). In general, the more manipulated variables available the better for optimization purposes, however without clear guidance how to effectively use them it becomes an “embarrassment of riches”."

Jan 1, 2012

By Richard Morland

Some simple and fundamental objectives To challenge and inspire our people to embrace safety as a value ?A stand for safety as a value ?A stand for our people ?A stand by our people ?Prevent harm to our people ?Eliminate suffering for individuals, families, friends, colleagues

May 1, 2010