Search Documents

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By Clifford S. Gibson

THESE troubled times suggest three reasons for maximum effort to control silicosis: (1) To keep to a minimum the ever-increasing burden occasioned by past deficiencies in this respect. (2) To effect the greatest production with maximum efficiency, which means at the least cost. (3) To preserve man-power in every way. Good control of the silicosis problem aids these aims. Inadequate control hampers all three. Insofar as our knowledge goes, silicosis in Ontario mines is caused by the inhalation of finely particulate quartz. It follows, therefore, that removal of dust containing this mineral automatically erases the cause. The achievement of this ideal is the aim of the mine operator. His best tool to this end is ventilation. This paper discusses mine ventilation from the viewpoint of dust control and it is hoped that in so doing there may result a better understanding of the part played by air in silicosis prevention. No attempt will be made to treat the subject fully. Instead, there will be presented certain salient aspects culled from field observations, the data in all cases referring to gold mines, unless mention to the contrary is made.

Jan 1, 1942

By L. Vollert

"The application of pneumatically-assisted fluidized bed flotation, specifically the ERIEZ HydroFloatTM technology, has found widespread use in non-sulphide processing (particularly phosphate, potash and coal) for the recovery of coarse particles. In gold processing, centrifugal gravity circuits and flash flotation cells are typically employed for the recovery of coarse and near-size liberated gold which tends to accumulate in recycled grinding streams due to bypass to the classifying cyclone underflow streams owing to the higher specific gravity of these gold particles. Early removal of this gold from the grinding circuits contributes toward the reduction of downstream processing losses as a result of overgrinding and particle shape deformation in the case of flotation processing, longer leach residence times in the case of extractive processing, and surface occlusions in the case of both flotation and extractive processing. Furthermore, recovery to bullion attracts higher payment terms by way of comparison to concentrate sales in the case of copper-gold concentrators. This paper assesses the application of pneumatically assisted fluidized bed flotation for the recovery of coarse liberated gold through the analysis of piloting data generated from the operation of a continuously operated 16 inch ERIEZ HydroFloatTM unit treating a sized coarse grinding circuit stream. The paper presents the stage recovery by size performance of the ERIEZ HydroFloatTM unit together with quantitative gold deportment analysis to demonstrate the efficiency with which gold was recovered during this pilot campaign and then compared to more conventional processing units – centrifugal gravity and conventional flotation.INTRODUCTION Newcrest Mining Limited (NML) has identified that an opportunity exists for improving the recovery of coarse composite particles at its current operations, both as a means for improving overall recovery and as an opportunity for early gangue rejection. As such, Newcrest Mining Limited has taken an interest in the application of pneumatically-assisted, fluidized-bed flotation i.e. ERIEZ HydroFloatTM technology. This interest dates back to 2011 with sighter testwork carried out on their Australian-held ore bodies (Kohmuench et al, 2013). Newcrest continues to assess ERIEZ HydroFloatTM potential for coarse composite recovery and, in the case of the topic of this paper, coarse gold recovery based on examples in the literature which demonstrate the efficiency of this technology in this regard (Carmona Franco et al., (2015); Miller et al., (2016); and Kohmuench et al, 2013)."

Jan 1, 2017

By G. A. Witwicki

"The Thyssen Mining Group of Companies has successfully applied ground freezing technology to numerous projects throughout Europe and North America for over 100 years. Recently, the aspect of data acquisition and data verification has received greater focus.Thyssen Mining has been engaged in several relatively deep shaft sinking projects over the past five (5) years, all of which have required ground freezing to successfully sink through water bearing rock. To safely and economically sink through a quantity of water similar to Saskatchewan’s Potash Mines, it is imperative to understand freeze wall thickness and growth rate.Critical to understanding freeze wall thickness and growth rate, is the collection of accurate data as well as the interpretation of those data. The data can then be utilized to gain a better understanding of the freeze wall growth rate in active projects as well as to provide data to be utilized in modeling for future projects.This paper elaborates on the installation and operation of the data acquisition system utilized at the Newmont Leeville project, Nevada’s first frozen shaft project. In addition, this paper elaborates on the methodology developed by Thyssen Mining to manipulate the freeze wall data derived through the data acquisition system.The successful incorporation of the new system of collection and analysis of freeze wall data for the Leeville Project has given Thyssen Mining a high degree of confidence in the understanding, as well as prediction, of the ground conditions during shaft sinking.This paper will include:•,A brief description of ground freezing and its objective;•,An overview of previous data acquisition methods employed;•,Current data acquisition methods;•,Installation requirements; and,•,Data manipulation and presentation methods."

Jan 1, 2015

By Lex L. Udy

External-detonation-generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall. The effects of this phenomenon on several explosive compositions and types are demonstrated and discussed. The explosives tested include aluminum-sensitized and explosive-sensitized slurries, ANFO, liquid explosives and dynamites. Various techniques are described that can be used to reduce or eliminate the plasma effect.

Jan 1, 1979

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks

A combination shaft-electric furnace for the smelting of ores and the melting of metallized feed is being developed at the Mines Branch. When iron oxide pellets are smelted in this unit, they are preheated and partially reduced in the shaft before being transferred to the electric furnace where smelting is completed. Also, limestone flux added with the pellets is-preheated and calcined in the shaft. It has been demonstrated that, in smelting iron oxide in this unit, the throughput of the 250-kva electric furnace can be approximately doubled and the amount of electrical energy required can be very significantly reduced when the shaft furnace is operated in conjunction with the electric furnace. These benefits are achieved mainly by utilizing the sensible heat and latent energy contained in the arc furnace off-gases.

Jan 1, 1971

By P. Tukkaraja, K. Katzenstein

"Block caving is one of the most economical and efficient underground mining methods and has gained popularity around the world especially for extracting low grade and massive ore bodies. However, during the extraction of ore from the draw bells, gases trapped inside the cave could emit into the working areas; hence, ventilation plays a key role in operating block cave mines successfully where gas emission is a concern. To design an effective ventilation system for a block caving mine, given the dynamic nature of the caving process, it is necessary to develop airflow characteristic curves (P-Q) for a given cave. This study uses a 1:100 scale physical model with an exhaust fan system, and a Computational Fluid Dynamics model of a block cave to investigate the airflow behavior through the cave filled with broken rock material. From this study, it was observed that the cave airflow resistance increases with the decrease in cave porosity and the particle size.INTRODUCTIONThe block cave mining method is gaining popularity owing to its low cost and high productivity. This study considered a case where this bulk mining method is used for the extraction of an orebody that contains uranium mineralization. During the extraction of broken ore from the draw bells, radioactive gases trapped in the cave zone could be released into the production drifts and could create unsafe working conditions in the mine. Mine ventilation systems play an important role in regulating the migration of radon in working areas. One of the strategies to control radon migration in a block cave mine is to exert negative pressure on the cave zone by using an exhaust fan above the cave zone. In order to select an appropriate exhaust fan system, it is necessary to study the airflow resistance of the cave zone (Loring & Nelson, 2006).Extraction of broken ore via drawpoints creates a void volume inside the cave called the air gap. Air gaps with larger heights can lead to air blasts in a block cave mine should the cave collapse. Besides that, the air gap can also lead to decrease in ventilation system efficiency due to recirculation of air flow and associated shock losses. Air gap height can also have a profound effect on the variation of cave airflow resistance (Erogul et al., 2015, 2017). The knowledge of cave airflow resistance is also important for predicting the intensity of an air blast. Cave airflow resistance is a function of cave properties such as broken rock size, air gap, and porosity inside the cave zone (Baysal et al., 2017). Initially, a scaled experimental model with a forcing system was developed to investigate the airflow behavior through the cave, however, this model couldn’t provide an observable change in the airflow resistance when the cave properties were changed (cave porosity, and airgap) This was attributed to the difficulties associated with forcing system in terms of achieving lower porosity values with the available material (lightweight shipping boxes) for simulating broken rock inside the cave zones, and controlling air leakage from the model (Ajitha et al., 2018)."

Jan 1, 2019

By S Romanchuk, V N. Macvkiw, D. J. I. Evans

The paper describes the processes developed and piloted by Sherritt Gordon Mines Limited for recovering copper, in the form of specification copper powders, from Lynn Lake sulphidic copper concentrates and Fort Saskatchewan Refinery by-product copper sulphides. The process includes ammonia pressure leaching and hydrogen reduction from solution. Nickel and cobalt present in the con-centrates dissolve in the leach solution and a method was developed for separating these metals from the cop-per. Methods are described for con-trolling the physical properties of the copper powder produced in the reduction vessel. The chemistry of the process is briefly discussed and the effects of some of the more important process variables are described. SHERRITT Gordon Mines Limited have developed and proven on a pilot plant scale, a process (I) for the production of copper powder

Jan 1, 1961

By C. Acuña

The case is presented that the key role of frother is control of bubble size in the pulp zone. Compared to water alone, the addition of frother produces a narrower distribution and finer bubble size. An empirical model is presented for bubble size as a function of frother type using a normalized concentration. The model provides a benchmark for assessing operations. There is no agreed upon mechanism of how frothers act to reduce bubble size. Prevention of coalescence is a common explanation and this action is illustrated. The case against the 'coalescence' model alone is presented and a breakup mechanism is introduced based on pilot cell and single bubble studies. Phenomena associated with bubble shape, velocity and surface flows are used to illustrate the force associated with surface tension gradients. Breakup mechanisms resulting from this force are proposed. The concept can be extended to high salt concentrations which also promote small bubbles.

Jan 1, 2007

By G. S. Hume

"THERE HAS BEEN a marked growth in the petroleum industry in Canada since the end of the war. The rate of growth in the demand for oil products has exceeded that in United States, although the per capita consumption is still less. Estimates of the consumption of petroleum and petroleum products in Canada in 1951 are approximately 154,000,000 barrels, which is slightly more than 11 •barrels per capita, whereas the estimated consumption in United States for the same period, according to World Petroleum, is placed at 2,619,- 970,000 barrels. This, on the basis of a population of 154,000,000, would be equivalent to 17 barrels per capita. The increase in consumption of the petroleum and products is world wide. World production in 1951 has been estimated (Oil and Gas Journal) at 11,700,000 barrels a day or more than 41;4, billion barrels for the year. United States production increased 13.7 per cent to 6,143,000 •barrels a day and Canada'.s ,, total production increased about 65 per cent from a total of 29,091,235 •barrels in 1950 to an estimated (Dominion Bureau of Statistics) 48,096,800 barrels in 1951.The trend to use increased amounts of petroleum and petroleum products, particularly in the United States and Canada, has also been supplemented by increased use of natural gas. The rate of expansion of the consumption of natural gas in United States in the past few years has been very rapid, increasing from 2,600 billion cubic feet in 1940 to 5,975 billion in 1950, with the proven reserves in the same period increasing from 85,000 billion to 186,000 billion cubic feet."

Jan 1, 1952

By J. A. Vezina

The effects of particle size distribution on metal extraction have been determined from pressure leaching Renzy Mines Limited concentrate with oxygen. Using a pulp density of 30 per cent solids, an oxygen pressure of 80 psig, a temperature of 230°F, a grind of 2.5 hours and a retention of 8 hours resulted in the almost complete dissolution of the nickel and the cobalt and the decomposition of over 96 per cent of the chalcopyrite finer than 20 microns. Only 11 per cent of the chalcopyrite coarser than 20 microns was reduced to smaller than 20 microns.

Jan 1, 1973

By T. B. Williams

THE British Columbia Coal Control was established in 1946 as a branch of the Department of Lands. Its functions are the administration of the Goal Act, the making of field and laboratory investigations bearing on the delineation and utilization of British Columbia coal deposits, and the dissemination of information concerning them. The Department of Lands in the Province of British Columbia retains and administers many of the Province's resources until such time as they are actively developed under the departments of Agriculture, of Forests, of Mines, etcc. The work of the Control is one of stock taking and appraising. We are picking up where the geological surveys leave off. In an effort to assist in the orderly, scientific development -of our excellent and extensive' ?Coat resources, we are bridging the gap between exploration and geological examination on the -one hand and mining on the other. All coal analyses required in the course of the investigations, together with? those requested by prospectors and others, are carried out in the very modern and efficient laboratories of the Coal, Petroleum, and Natural Gas Control. At its inception, the Coal Control began an investigation of coal seams in the Peace River area, specifically those contiguous to the Pine River valley about one hundred miles west of Dawson Creek. The occurrence of coal in the Peace River canyon, east of Hudson's Hope, bad been known since 1792, but the first record of production is for 1923.

Jan 1, 1951

By Jayesh B. Patel, Zhongyun Fan, Hu-Tian Li

"Melt conditioned direct-chill (MC-DC) casting is a novel technology which combines vertical direct-chill (DC) casting with a high shear device directly immersed in the sump for in situ microstructural control. In this paper, the solidification mechanism of DC casting under varying conditions is discussed. The temperature profiles in the sump were measured under the steady state casting conditions by using sacrificing thermocouples. Detailed comparisons of the derived thermal condition are made. The individual role of grain refiner additions, natural thermosolutal convection and forced convection in the sump and the interplay of these factors in determining the solidification structures of DC cast billets are discussed. The MC-DC casting technology can be used to control microstructural constituents and casting defects in DC cast billets/ingots by in situ manipulating of the thermal and fluid flow conditions.INTRODUCTION Direct-chill (DC) casting of aluminium, has been the essential commercial process for producing feedstock suitable for subsequent processing, such as extrusion, rolling or forging. Fine and equiaxed grain structures in the as-cast billets/ingots are required to enable a fine and uniform distribution of second phase particles and microporosity. This leads to higher productivity, more cost-effective homogenisation and more efficient downstream thermomechanical processing. The addition of chemical inoculants has been the standard industrial operation prior to casting for grain refinement of Al alloys. However, it has been established that less than 1% of the grain refiner particles added actually act as heterogeneous nuclei to refine the grain structures, showing a very low grain refining efficiency (Greer, Bunn, Tronche, Evans, & Bristow, 2000). Moreover, the remaining particles from the grain refiner addition in the final casting may cause surface defects during downstream processing. A major issue of the metallurgical quality of large sized ingots/billets is the non-uniformity of microstructures even with chemical grain refiner additions. This is due to the fact that the grain structure formed in the different zones of the billet depends on the local chemical composition and local cooling rate. The local cooling rate can vary from 0.4~1 K/s at the centre of the billet to around 10–20 K/s at its surface zone (Nadella, Eskin, Du, & Katgerman, 2008). The large thermal gradient along radial direction between billet surface and interior of the melt during conventional DC casting induces thermal stress and cold cracking even with grain refiner addition. Therefore the control of casting defects, such as macrosegregation, porosity, cold/hot cracking and distortion of the billets/slabs, etc., is still challenging in industry, causing high scrap rate of DC cast ingots/billets even with grain refiner addition."

Jan 1, 2018

By John Dasher

The analyses reported on in this paper indicate that there are hydrometallurgical routes from sulphide concentrates to copper that are potentially competitive with smelters which are not permitted to emit sulphur oxides. The various hydrometallurgical processes, and their economics, are discussed.

Jan 1, 1973

By C. H. Tiernon

"This paper was' prepared to emphasize the part that coal washing tables can play in the development of many of the reserves of coking coals in Western Canada_ It covers a brief history of the development of the coal washing table through the present third-generation unit, which suspends from overhead steel beams and is driven by a counter-rotating gear mechanism. The design and operation of this unique table are covered in detail.An analysis of actual operating data is included, with explicit statistical breakdowns of the table products. The data used were actually produced by operating coal companies, and also produced by the United States Bureau of Mines while gathering data for a research investigation. Table feed capacity is discussed, as well as performance criteria and the parameters of relative table performance. Several typical table flowsheets are described, emphasizing the specific reasons for their use. The paper covers the past and present value of the table to the United States coal industry, and makes mention of the newest addition to the family of suspended, multiple-deck, counter-rotating, gear-driven, coal washing tables, the CONCENCO ""88"" Deister table."

Jan 1, 1973

"Real-time, on belt analysis of minerals is becoming increasingly important and critical in modern operations, especially in the mine-to-mill. Prompt gamma neutron activation analysis has long been utilised for real-time elemental analysis in bulk materials, with Scantech's GEOSCAN being the instrument of choice in the minerals sector. Working in the minerals space for 15 years, the GEOSCAN has been successfully implemented in a wide range of minerals applications including iron, copper, lead-zinc, manganese, phosphate and more, and it caters for the very high demands and increasing requirements of a contemporary processing facility. An area of focus has been on increasing the analysis frequency to allow for rapid analysis results with the same high degree of accuracy typically expected of the GEOSCAN. This paper discusses the underlying research and technology that has enabled such rapid analysis and presents a range of examples using a thorough statistical approach on real production material, demonstrating achievable accuracy over a short analysis time, and dispelling common myths about the speed of the technique. Potential applications are discussed to conclude the paper.INTRODUCTION Technology and the information it can provide plays a critical role in the evolving modern mineral processing landscape. The importance of technology to analyse various features of ores and concentrates being processed is obvious, and recent years has seen the advance of numerous technologies to provide a variety of real-time measurements on conveyed material flows. From sampling apparatus to particle size analysis to weight and density meters to full elemental analysis, the availability of information enables a variety of improvements in the process leading to improved efficiency and increased revenue. To maximise the potential benefits, access to real-time information is imperative, and rapid updates of information become necessary to make appropriate process control decisions based on the most relevant and up-to-date information."

Jan 1, 2017

By Guangyuan Li

A 3-D block-spring model (BSM) has been developed for simulating the behaviour of jointed rocks. The model uses a discontinuous formulation and an iterative procedure to solve the large displacements in jointed and faulted rock masses. The 3-D BSM has been used to simulate mining excavations in jointed rocks around an open pit and underground settings. The applications have demonstrated that it is a practical tool to solve complicated problems of rock mechanics in civil and mining engineering. This model has recently been modified to incorporate complex geological conditions, such as underground water flow (seepage), unstable blocks and the time-dependent behavior of backfill materials. To demonstrate the capability of the 3-D model this paper presents the fundamentals of the 3- D BSM and its application for open-pit mining. A complete computer package BSM3D has been developed based on the 3-D block-spring model. The package consists of a solving engine for numerical analysis and a Windows based processor for mesh generation and results display. The multi-functioned pre-processor provides tools and menus to help users setting up models easily and conveniently. The fully featured post-processor allows users to view the results in different windows and orientations. The graphical results include contours, vectors, animation of rock movement, and the failure state of the rock structures.

May 1, 2001

By Lauri Pesonen

"Although electrical energy use at copper smelters is typically about 15-20% of operational costs, it is something which is not very often analyzed and discussed at a detail level in technical papers and presentations. This paper aims to list different equipment configurations per smelter area and estimate their electrical energy consumptions versus unit of material processed. In addition chosen smelting technology and oxygen enrichment rates affect the overall electricity consumption and therefore some overall guidance is provided for efficiency gains.INTRODUCTION In principle, processing plants, such as copper smelters, require electrical and chemical energy together with some degree of human input to process input materials into desirable output form like metallic copper. From the standpoint of metallurgical plant designers, the thermodynamics of smelting, when it comes to releasing and conserving thermal energy, is sufficiently understood and frequently discussed in the literature in detail, but judging from the quantity of publications, the way how we exactly utilize electrical energy is not. This article is meant to illustrate how electrical energy consumption is distributed among different process units and equipment types at copper smelters using various smelting technologies. In general, typically about 15-20% of operational costs are related to electricity and at locations with high electricity prices the potential savings can be quite significant for the overall profitability of the plant operations. In today’s tight profit margin environment any potential savings are more than welcome. The purpose here is not to promote any certain copper smelting technology, but to open a discussion on how and where we use electrical energy, and how the overall energy use could be lowered with the implementation of newest electric power saving designs and solutions. Using the principles outlined in this article, it should be fairly easy and straightforward to replicate the calculations and even improve them wherever it is seen necessary for the greater benefit for us all in this industry"

Jan 1, 2017

By Jirí Faltus

The paper deals with studying the impact of structural properties and anodizing of surface on the corrosion properties of extruded rods from commercial aluminium alloys: AA6082, AA6262, AA6012, AA2007 and new lead-free aluminium alloys AA6023, AA2015 and AA2111B. Samples were exposed to the corrosive atmosphere NSS, AASS in the chamber by EN ISO 9227. Surface of samples were either in the original state or anodizing by selected mode. The depth of corrosion attack and the form of corrosion attack are evaluated depending on the type of alloy, the metallurgical condition and surface treatment of the samples.

Jan 1, 2015

By L. T. Munn

"IT IS NOT necessary here to dwell on the fact that sulphur is currently in short supply. It may be well, however, to •point out that this •storage is not merely a temporary condition, but that, judging by trends in world consumption of sulphur, it may •be anticipated that requirements will double in the next ten years.Even with improved techniques for mining elemental sulphur in the United States and the new finds in Louisiana, there is much concern as to how these future sulphur requirements can be met. It appears necessary to .turn more and more to other sources than elemental sulphur for •additional production. The three major alternative sources were:(1) By-product sulphuric acid •from smelter gases.(2) Sulphur and sulphuric acid from iron sulphides.(3) Sulphur from hydrogen sulphide contained in natural gas. The Jumping Pound sulphur plant of the Shell Oil Company of Canada, Limited, is designed to produce sulphur by the •third of these methods.Jumping Pound is a natural gas field about 20 miles west of Calgary where Shell has a number of producing wells."

Jan 1, 1952