Search Documents

By B. Drew, K. Budna, C. Wenzl, D. Gregurek, A. Spanring

"The metallurgy of nickel and cobalt and of copper is closely interlinked when processing sulfidic Ni-Co ores and Cu-Co ores. The respective furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear mode. This paper evaluates the common refractory wear mechanisms, namely infiltration, spalling and chemical attack by various slag systems, as well as sulfur attack, as observed when processing primary sulfidic ores. All these wear parameters, which are discussed in this paper, lead to a severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” is an important prerequisite for the refractory producer. Based on such research results, combined with specific process knowledge, appropriate brick lining solutions for nickel and cobalt processing furnaces can be recommended.INTRODUCTION The metallurgical production of cobalt and nickel and of copper is closely interlinked to the mineralogy of the respective ores: cobalt is found in African Cu-Co ores as well as in Co-rich nickel ores (laterites and sulfides). Also, Co-bearing secondary raw materials contain the mentioned elements in different contents. In pyrometallurgical processing of sulfidic ores, cobalt is generally recovered as a by-product during the production of copper and nickel, whereas it is normally not recovered separately during the processing of nickel laterites but remains in the FeNi product. Besides various hydrometallurgical production routes, the pyrometallurgical processes involved comprise smelting (i.e., production of a Cu-Ni-Co-Fe matte in electric or flash furnaces), converting and refining (i.e. removal of Fe and S as well as other elements from matte by oxidation). The ongoing trend to use higher oxygen enrichment in process air enables higher intensity processes but also increases the oxidation potential in the vessel. Therefore, during smelting and especially during the oxidative treatment in converting and refining, some amounts of valuable metals are also transferred to the slag in their oxides form. A subsequent slag treatment is then applied for recovering valuable metals from the slag, namely allowing an economic material stream handling and minimizing metal losses. This is often done in a slag reduction furnace. Additionally, copper and nickel are very good collectors for precious metals and platinum group metals (PGMs) - therefore, depending on the content of these metals, an additional refining process is used to recover these valuable metals from the matte or metal phase (Elvers et al., 1997; Davenport et al., 2002; Crundwell et al., 2011)."

Jan 1, 2017

By K. Gardner

"Many deposits have a geological model developed early in the project stages, which is not always reviewed or modified as the project matures and production commences. Conversely, ongoing pressures, due to a combination of declining head grades, a push for increased revenue and a multitude of other reasons, leads to processing plant modifications, with the primary aim being to increase production. Often, the ore deposit knowledge is not sustained or developed during the operational stages to the level carried out during the prefeasibility and feasibility study phases. This results in the variability within the deposit being poorly understood and a lack of data and knowledge being available to support (and ideally optimise) operations particularly in an environment where the flow sheet has changed and ore feed requirements are complex.INTRODUCTION This paper presents a case study of ore deposit knowledge development and corresponding process plant operating strategy at the Ladolam Gold Deposit, commonly referred to as the Lihir gold deposit in Papua New Guinea. The gold deposit is located in a tropical equatorial climate on the east side of Lihir Island in the New Ireland Province of Papua New Guinea. Gold mineralisation was discovered in 1982, and was followed by a major exploration campaign by a joint venture between Kennecott (Rio Tinto) and Nuigini Mining Limited. The first drillhole was drilled in 1983, and after an extensive period of drilling consisting of 343 holes for 83,500 m, the final Feasibility Study was completed in 1992. The feasibility study was based on a Reserve base of 37.9 Moz in refractory sulphide ore, with gold extraction proposed to occur via whole ore pressure oxidation due to the refractory nature of the mineralisation. The Lihir Special Mining Lease (SML) was granted in 1995 to a new PNG company – Lihir Gold Limited, and Rio Tinto established Lihir Management Company to develop and operate the mine on behalf of LGL. Mining and processing of the deposit commenced in 1997. Newcrest Mining Limited purchased Lihir Gold Limited in August 2010, and subsequently completed a major plant upgrade including the installation of additional grinding, autoclave and carbon-in-leach capacity. Post commissioning of the upgrade, Newcrest has continued to increase throughput and production. A reinvigorated ore body knowledge development program has significantly assisted this process in identifying operating strategies for the process plant and delivering recovery improvement projects to address declining head grade and recovery due to increased stockpile feed and flotation circuit use."

Jan 1, 2017

By Pim van Geffen, Dave Lawie, James Cleverley

A growing problem facing geoscientists, metallurgists and process engineers is the lack of knowledge transfer between the exploration and production teams. This siloing is generally unintentional, as a typical project may change ownership several times over several decades before it reaches the feasibility and operation stages. Many exploration projects generate vast amounts of high-quality, quantitative data with great spatial resolution, but unfortunately these data are often ignored in subsequent deposit modelling. Instead, deposit models tend to rely on subjective, non-standardized, qualitative classification of geological materials (e.g. rock type, mineral abundance) and processes (e.g. alteration style and intensity), obtained through visual logging of drill core. When projects advance to feasibility studies, the required quantitative data are obtained through expensive metallurgical test work and detailed quantitative mineralogical analysis, such as QEMScan or qXRD. These detailed tests are generally only performed on a small number of large composite samples and the results are extrapolated throughout the deposit, inherently underrepresenting their true variability. Geochemical data obtained during all stages of the project provide comprehensive data coverage at much greater detail and spatial resolution, which allows for the estimation of key metallurgical performance parameters that are required for accurate deposit modelling and domaining.

Jan 1, 2015

By K. L. Azinger

Successful relationships between mining companies and local stakeholders are now an essential part of the social contract of “doing business” (Prescott, 1995). The methodology presented in this paper is designed to assist mining companies in understanding and building relationships with diverse stakeholder groups. The methodology starts by recognizing that mining projects have a natural life cycle which can be used to identify when new external affairs strategies are required. In designing an external affairs strategy, the first step is to set objectives that are compatible with the overall objectives of the mining project. The management team then identifies the main stakeholder groups and seeks to understand the priorities and inter-relationships of the individual stakeholders. The result of this stakeholder analysis is an understanding of the Degrees of Influence of each of the stakeholder groups along with a relationship map which illustrates the strong interactions between stakeholders. The company is then prepared to take a proactive approach to building relationships with the primary stakeholders. This methodology was developed by BHP to assist with the federal government environmental approval process for the development of Canada’s first diamond mine. BHP has successfully used the methodology in three different phases of the NWT Diamonds Project and is now applying the methodology to mining and development projects around the world.

Jan 1, 1998

By C. A. Ingram

The Cigar Lake ore body is a high-grade uranium deposit situated within water-saturated sandstone. In order to extract the uranium ore remotely, ensuring minimal radiation dose to workers, and also to access the ore from stable ground, the Jet Boring System (JBS) was developed. This method of mining involves drilling a pilot hole up through a frozen ore body and utilizing a high-powered water jet to mine out cavities. During the mining process an ultrasonic sensor will be used to provide feedback to the operator, who is located beneath the ore body, as to the dimensions of the cavity. However, more precise data is required to determine final shape, volume, and location of the cavity for mine planning purposes. Selecting a device that will provide sufficient range data in the challenging environment will be vital to optimizing the mining process. Major issues include fog build up and flying debris during mining, and an environment that is wet, dark, and cold A test cavity has been designed and constructed at the Saskatchewan Research Council (SRC) so that a study comparing three different technologies, as prospective candidates for the survey system, can be conducted. The devices being evaluated include a Senix ultrasonic sensor, an MDL Cavity Auto-Scanning Laser System (C-ALS), and a MESA Time of Flight (ToF) camera. The ultrasonic sensor is known to provide range data in foggy conditions but has low accuracy. The C-ALS has been developed for surveying remote cavities but is expensive and does not provide reliable data in fog. The ToF camera provides a high volume of data in a short time period, with potential to provide accurate information in extreme conditions, but has not been tested in a mine cavity application. Iterative closest point (ICP) registration is applied in an attempt to create a 3D point cloud from the scan data and to also compute rotation and translation of the ToF camera. This paper presents an overview of the challenges involved in conducting a survey within a JBS mined cavity, the analysis used to determine the suitability of each device, and the data collected from the test cavity.

Aug 1, 2013

By D. C. Carter

"The Nova Scotia Department of Mines and Energy located a drillhole at Riverside Corner, Hants County, Nova Scotia, to examine the stratigraphy, structure and potash potential of the Kennetcook River gravity low. This evaporite-related gravity anomaly is one of the largest virtually unexplored gravity anomalies in Nova Scotia. The drillhole intersected a structurally complex sequence o flower Windsor Group ('B' Subzone) evaporites. Downhole geophysical wireline logs were used, in conjunction with detailed lithological descriptions, to interpret the structure and stratigraphy of the sequence. Similar application of total gamma ray, density, caliper and neutron-neutron log responses allows stratigraphic correlation of Windsor Group carbonate marker units separated by up to 35 km in Cape Breton. This work confirms the value of downhole geophysical logs as a tool in the exploration of evaporite deposits regardless of the presence or absence of high quality core. INTRODUCTIONThe exploration methodology for evaporite (specifically salt/potash) deposits in eastern Canada (and worldwide) is relatively simple: identify a negative gravity anomaly within a favourable geological setting, Windsor/Cordroy Group sediments in eastern Canada, and drill it (Anderle, 1980). Although this is an obvious oversimplification of the necessary expertise in the planning and complet ion of an exploration program, those familiar with potash exploration drilling can attest to the risks and expense, in terms of time and problems , associated with the location and drilling of diamond-drill wildcat holes. Potash exploration programs in eastern Canada, their results and inherent difficulties, have been documented by Anderle et al. (1979), Cooper (1981), Dekker (1982), Carter and Boehner (1986), Carter (1988) and Carter and Anderle (in prep .).Downhole geophysical wireline logs have become an important tool in the stratigraphic and structural interpretation of evaporite sequences in eastern Canada and, in many cases, represent the only information recovered or the only information available due to the drilling method (rotary) and/or the long term instability of evaporite cores. This paper documents examples of downhole geophysical log responses which, combined with detailed lithological examination of drill core, or in the absence of core, are used in the interpretation of the complex lithology and structure of a deformed evaporite deposit. Geological and geophysical data from the Nova Scotia Department of Mines and Energy (NSDME) Riverside Corner 85-1 drillhole are presented here as a partial case history and prime example of the use of this method to interpret the complex structure of an evaporite deposit. Drilling of NSDME Riverside Comer 85-1 was conducted in late 1985and early 1986by the Department (Carter and Boehner, 1986) under a program to assess the potash potential of selected areas of the province as part of the Canada-Nova Scotia Mineral Development Agreement 1985-89. A reinterpretation of a portion of the available data from two exploration drilling projects on Cape Breton Island in the Canso-Bras d'Or area is also presented (see inset, Fig. I). Several drillholes have intersected the Windsor Group evaporite sequence in these areas and the available geophysical logs are a valuable tool in the interpretation of the structure of the deposits. However, no attempt has been made to present or discuss the detailed geological investigation and comparison of these two deposits. They are presented here as an example of the reinterpretation of existing data and their application to stratigraphic correlation and structural interpretation of complex evaporite deposits. Further work is necessary to document the stratigraphic and structural correlation of these two areas."

Jan 1, 1989

By D. M. Rippley

THE St. Lawrence Seaway Project ranks with the greatest engineering undertakings of all time. A summary of major materials going into the construction of this project, shown in Table I, will assist in an appreciation -of this fact. These data relate to Seaway construction only, and it should be remembered that two large-scale power projects are in the construction stage on the St. Lawrence river concurrently with construction of the Seaway. A project of such magnitude as the Seaway would attract widespread interest even if it were being constructed in a remote area. The fact that it is located in a heavily populated and developed section of both Canada and the United States has done much to enhance this interest, and in many ways complicates the problems confronting the engineer in the design and construction phases. Many consider the St. Lawrence Seaway to be a new idea that has developed within the past decade - such is far from the fact, because the St. Lawrence River canal systems have existed for more than a century, and the Seaway Project is but a new, larger, and more efficient version of a continually expanding facility.

Jan 1, 1957

By M. Noaparast, N. Nickoletopoulos, André R. Laplante

"This paper presents an application of the use of synthetic ores to study gold recovery by gravity. Three case studies are presented: the first focuses on the use of tungsten to study applications of Knelson Concentrators for upgrading gravity concentrates; the second on tungsten again, in this case to study the performance of a 86 Falcon Concentrator; and the third on lead to mimic gold's grinding behaviour.It is shown that the use of synthetic ores with metallic substitute for gold is not only expedient, but it can also lead to an increased understanding of separation and grinding mechanisms, because of the more accurate results and controlled particle shapes. The case studies highlight the problems associated with gold particle flakiness and gangue density. The grinding behaviour of malleable materials is shown to be complex, as particles can migrate to coarser size classes by flattening and cold welding, and to finer size classes by folding and actual breakage.IntroductionThe title of this contribution is not entirely misleading. Mineral processing has much to do with philosophy, rather Philosophy, as described by Georgius Agricola:""Furthermore, there are many arts and sciences of which the miner should not be ignorant. First there is Philosophy, that he may discern the origin, cause, and nature of subterranean things; for then he will be able to dig out the veins easily and advantageously, and to obtain more abundant results from his mining. ""1"

Jan 1, 1995

By Janice Zinck, Maziar E. Sauber

"To counter the recent uncertainty in the rare earths market, diversify the supply source, and help meet the future demand in this sector Canada initiated development of several new rare earth deposits. In the past few years, a number of various studies on rare earths plant design have taken place mainly covering process development, process selection, and flowsheet design. The purpose of this paper is to provide an overview of known domestic and potential resources and reserves of rare earths and their status quo with a focus on the metallurgical processes using the information available in the public domain. Plant designs currently under consideration in Canada are reviewed and evaluated. An outline of the areas of opportunity for selective innovation and technology development in the rare earths flowsheet development and the associated risks and rewards is provided.INTRODUCTIONThe rare earth elements (REE) have a very small annual market, but they are categorized as very strategic metals vital to global economic growth due to their indispensability to the development of modern defence system, green technologies and electronic applications. The International Union of Applied and Pure Chemistry (IUPAC) defines the REE as the 15 elements on the lanthanide series on periodic table of elements, plus yttrium and scandium. REE are classified as light rare earth elements (LREE; La to Gd), and heavy rare earth elements (HREE; Tb to Lu). Physical properties and chemical reactivity of yttrium is similar to those of HREE, thus it is categorized as such. Properties of scandium are not similar enough to classify it as either a LREE or HREE (Weng et al., 2015; Sappin & Beaudoin, 2015). However, the mining industry does not always abide to this definitive classification of the split between LREE and HREE. Therefore, in a comparative study of projects, there is a need to pay attention to how the elements are classified."

Jan 1, 2016

By K. R. Brown, P. L. Krawchuk

In-situ recovery (ISR) is under increased investigation as a viable methodology for the extraction of minerals in ore bodies that may be uneconomic to mine by traditional methods or for resources situated in locations where underground and surface mining operations are not feasible. Although the concept of ISR is relatively new with respect to hard rock applications, it is not a new technology; it has been used successfully in potash and uranium mining and also in heavy oil extraction for years where it has been proven to be both technically and commercially viable. ISR allows for the extraction of metals and minerals without the need to mine large amounts of ore that need to be processed at surface. The ore stays in-situ and only the valuable metals and minerals are produced to surface in a process that produces very little to no waste rock or tailings. This paper aims to discuss the geological conditions that make ISR amenable to an ore body as well as the application of maturing technologies such as advanced directional drilling and the creation of artificial permeability that will help to access deep ore bodies and enhance or create favorable recovery conditions for ISR in the ore body. INTRODUCTION In-situ recovery (ISR), also referred to as in-situ leaching, is a potentially disruptive technology for the mining industry. ISR is under increased investigation as a viable methodology for the extraction of valuable minerals that may be uneconomic to mine by traditional methods or for deposits situated in locations where underground and surface mining operations are not feasible. Although the concept of ISR is relatively new with respect to hard rock applications, it is not a new technology; it has been used successfully in potash mining, uranium mining and also in heavy oil extraction for years where it has been proven to be both technically and commercially viable. Recently there has been increased interest in deploying ISR in hard rock applications due to a number of factors: the drive for environmental stewardship is stronger than ever, technological advances in drilling, blasting, and leaching are strengthening ISR economics, and a large inventory of ore bodies exists that are not feasible to mine or extract using conventional open pit or underground mining techniques. ISR allows for the extraction of valuable metals and minerals without the need to mine large amounts of ore that need to be processed at surface. The ore stays in-situ and only the valuable metals and minerals are produced to surface in solution via a recovery process that produces very little to no waste rock or tailings. Where the right conditions exist, the ISR process has a much smaller environmental footprint (Hiam-Galvez, 2018) and potentially much lower capital and operating costs than using conventional mining techniques.

Jan 1, 2019

By R. C. Beard

"Heap leaching, currently being applied in the treatment of low-grade ores in the south western United States, is shown to have potential for use in north western Ontario. The history and operation of the process are described, and cost comparisons are given.IntroductionHeap leaching is a simple, low-cost method of recovering gold from low-grade ore. Although it is not currently being used in Canada on a production scale, it is being used extensively, and successfully, in the southwestern United States as well as elsewhere in the world. Especially suited for large deposits of very low -grade ore, it also appears to be practical for use on small, high-grade deposits because it avoids the high capital costs of mills. Eveleth (1980) and others suggest that the capital and operating costs required for heap leaching are approximately 20% and 40% respectively of conventional milling methods.Northwestern Ontario is noted for its large number of undeveloped, small, high-grade gold deposits. Although there are a number o f larger and higher-grade deposits in the area as well, it is the relatively small undeveloped deposits which would benefit most from heap leaching, if it could be demonstrated to be a viable extraction method.To assess the significance of these small deposits, the Ontario Ministry of Natural Resources recently commissioned a consultants' study of the gold reserves in certain parts of northwestern Ontario. This report, titled ""Feasibility of Small-Scale Gold Mining in Northwestern Ontario"", by J.N. Neilson and R.C.E. Bray (1981, OGS Open File Report 5332), documents 106 known gold deposits having sufficient information to calculate gold reserves. A total of over 7.8 million tons having a weighted average grade of 0.19 oz of gold per ton were compiled in the proven, probable and possible categories, with an additional 8.2 million tons in the speculative category. Many of these deposits could be mined by open-pit methods."

Jan 1, 1983

By J. C. Ingram

IT SEEMS particularly appropriate that, in celebrating its Diamond Anniversary, the Canadian Institute of Mining and Metalturgy chose our Province of British Columbia as its locale in this, our own Centennial year. I am sure your organization is justifiably proud of its achievements and growth over the period of its sixty years, and we, for our part, are justifiably proud of our growth over our first one hundred years. With your kind indulgence I pro-pose to talk to you today about our industrial growth, or, to put it an-other way, to highlight, historically, our progress in industrial development over the past one hundred years, and to take the liberty of speculating on what we may reasonably look forward to over the next few years. I am sure, Mr. Chairman, that some may have questioned the appropriateness of a talk on the industrial development of British Columbia to the Canadian Institute of Mining and Metallurgy. However, strangely enough, we in British Columbia owe our origin, constitution-ally and industrially, to the mining industry.

Jan 1, 1958

By J. M. Hong, H. K. Zheng, R. Hu, C. B. Zhou

The Jinping-I double curvature arch dam, located in the middle reach of the Yalong River and with a maximum height of 305 m, is the world highest dam of the same type that has been completed. Since the second and third periods of the reservoir impounding, after which the reservoir water level was raised by about 200 m, a significant amount of leakage was observed out of the drainage holes deployed in the lowest drainage tunnel at the left-bank abutment at EL. 1595 m, with a pressure of 0.3 MPa at one typical hole when it was blocked. In this study, a number of analyses including water quality analysis, digital borehole imaging, tunnel geological mapping and in-situ groundwater monitoring were performed to investigate the source of leaking, the leakage passages and the performance of the grouting curtains. An inverse modeling procedure combining the orthogonal design, finite element forward modeling of the transient seepage flow, artificial neural network and genetic algorithm was invoked to further evaluate the permeability of the foundation rocks whose permeability was underestimated in design, using the in-situ measurements of flow rate and piezometric head. The geological structures that lead to the leakage were identified and the seepage flow behaviors in the dam foundation and the left bank abutment were assessed. Given the connectivity nature of the sub-vertically oriented fractures that induce the leakage event, it is found that some of the drainage holes with relative larger amount of discharge could be closed or blocked for reducing the amount of leakage without remarkably increasing the pore water pressure in the foundation rocks.

Jan 1, 2015

By G. A. Gross

"The Soviet Union has enormous reserves of iron ore in many different kinds of deposits that are widely distributed in this vast land area. The present iron ore industry is based mainly on deposits in Precambrian cherty iron-formation at Krivoy Rog, Kursk and Murmansk. Extensive reserves of both naturally enriched hematite ore and magnetite iron-formation in these areas alone could sup-ply all the domestic ore required for several hundred years.Many contact metasomatic magnetite deposits discovery in recent years in the eastern Ural Mountain belt and east of the Kusnetsov basin in Siberia are being developed, with ore reserves measured in billions of tons. Oolitic limonite-chamosite-siderite ores of Cretaceous and younger age at Kerch on the Black Sea and around the east and southern perimeter of the West Siberian basin constitute some of the largest concentrations of iron in the world. These sedimentary ores are low grade, of poor quality and difficult to beneficiate. Banded jasper magnetite and hematite iron-formation in volcanic rocks of Devonian age in Kazakhstan and along the Mongolian border are of special geoloica1 significance.Iron deposits in the Krivoy Rog and Kursk areas were examined and a large number of geologists discussed their work on deposits in many other parts of the Soviet Union during the writer's seven-week study tour of mines and research institutes in Moscow, Leningrad, Novosibirsk in Siberia and Kiev in the Ukraine. The descriptive geology of iron deposits of useable ore and of marginal material has been well documented in the course of systematic work and a large number of scientists are studying fundamental problems on the origin and treatment of iron ore."

Jan 1, 1967

By Long Han, Beijing General Research Institute of Mining and Metallurgy, Yu Xie, Yunhai Zhang, Yangge Zhu, University of Science and Technology Beijing, Yanbo Shang, Xingrong Zhang

"The first-principles method was employed to study the adsorption of hydroxyl calcium (CaOH+) and hydroxyl (OH-) on hematite and quartz surfaces. The calculation results suggested that OH- preferred to interact with the active Fe sites on the hematite surface, whereas OH- adsorbed on the quartz surface by weak hydrogen bond. Though CaOH+ could easily adsorb on the hematite and quartz surfaces by the formation of Ca-O bond, the covalence formed on the quartz surface was apparently stronger than that on the hematite surface, meaning a stronger and more stable adsorption. CaOH+ adsorbed on quartz surface was mainly through the interaction of O-2p and Ca-3d states, and this interaction on hematite surface was weaker.INTRODUCTIONIron Increase and Silicon Reduction Technology (Yu & Duan, 2002) of hematite is mainly through the reverse flotation (silica is floated away from the iron concentrate). There are two ways to achieve this (Houot, 1983). One is to collect quartz by cationic collector directly; the other is to activate quartz by lime and then collect it by anionic collector. There are two main different views with respect to the mechanism of quartz activation: mono-hydroxyl compound theory (Fuerstenau, Rice & Somasundaran, 1965; Fuerstenau & Palmer, 1976) and surface hydroxyl precipitation theory (Hu & Wang, 1988; Wang & Hu, 1990). The former indicated the formation of the mono-hydroxyl complex is one of the two criteria of quartz flotation. The later theory, on the other hand, suggested that surface precipitation is the adsorption of active species of metallic ion on quartz surface. However, most of those researches are based on the solution chemistry of flotation and little is done at the microscopic level.In this paper, by the help of first-principles calculations, the adsorption models, bonding conditions, Mulliken charge populations and adsorption energies of hydroxyl and calcium hydroxyl ions (OH- and CaOH+) on hematite (001) and quartz (100) surfaces were investigated to find out the lime activation of quartz at atomic level, which is significant for the researches of quartz activation theoretically and practically."

Jan 1, 2016

By G. F. Raymond, W. P. Armstrong

"At the time of this study, the Valley mine was producing 23 000 tonnes of ore per day from a large, low-grade porphyry copper orebody. Sulphide mineralization, principally bornite and chalcopyrite, occurs in a stock work of quartz veins in one phase of the Guichon Creek batholith. The property was explored from 1967 to 1982, and was placed in production in 1983.Using a three-parameter lognormal approximation developed by G.F. Raymond at Similkam een and Mount Isa Mines, a geo- statistical conditional probability ore reserve was estimated prior to mining. Comparisons with blasthole kriging and milled ore for the first 17 months of production showed close agreements at all cut-offs between conditional probability estimates and mineable ore. This was not true of either kriging or polygon estimates. An important part of this work was identifying and correcting for bias in both exploration and blasthole samples.IntroductionCominco's Valley lake deposit is a large, low-grade, porphyry copper orebody in the Highland Valley of British Columbia. Total indicated plus inferred ore reserves are 700 M tonnes at ore grade of 0.47070 Cu. At the time of writing, ore milling is at a rate of 23 000 tI d through the old Bethlehem mill. Mining is in 10m horizontal benches using 9.8 m3 shovels and 90 tonne trucks. Since this paper was written, Valley and nearby Lomex have been combined into Highland Valley Copper with a combined oreproduction of about 120 000 tI d.Copper mineralization, principally bornite and chalcopyrite, is regularly distributed throughout the deposit as disseminated low-grade within a granodiorite host rock, and as higher grade veinlets within a stock work of near-vertical quartz veins generally 10 cm or less in width. It is likely that problems with sample variability and sample bias are mainly related to mineralization within quartz veining. Valley geology has been described in detail by Allen and Richardson and by Osatenko and Jones (2). The exploration sampling program and identification of diamond-drill sample bias have been discussed by Armstrong and Newman'»."

Jan 1, 1988

By W. E. Cockfield

This paper is not intended as an original contribution to this subject, but rather as a review of the main theories which are held with regard to placer deposits, with, of course, particular reference to the placers of British Columbia. The present interest in gold mining has, however, brought the subject of placers to the fore, and possibly a brief outline of the geology of such deposits will serve as a basis for discussion on the subject. In Canada, the most valuable of our placers are deposits of gold, and consequently the discussion will centre largely on placer-gold deposits. The same principles apply, of course, to placer deposits of other metals. The Origin of Placer Deposits As a starting point, the idea which is prevailingly held is that placer or alluvial gold is detrital in origin, that is to say, the gold originally existed in veins, lodes, or disseminations in the country rock of the regions in which the placer deposits are now found, and that, through the various erosive forces of nature, it was liberated from those veins or lodes and concentrated in the form in which we now find it. 1 have not time to go thoroughly into the proof of this, but the lines of evidence are many. If we take the Cariboo district as a typical example, Johnston and Uglow(l) have shown, first of all, that the placer and vein gold are identical in character. Crystals occur both in the placers and in the lodes, but the crystals in the placers are nearly always slightly worn, indicating transportation.

Jan 1, 1932

By F. A. McLean

The past decade has witnessed a rapid increase in the number and variety of uses found for internal combustion engines in mining operations. Gasoline engines are now widely used for operating core drills, pumps, compressors, small hoists, switching locomotives, tractors, boats, and other equipment. The heavy-oil engine is employed for operating compressors, generators, shovels, ore-milling machinery, and- in the iron, copper, and coal districts- in connection with that' latest newcomer in modern railroading, the oil-electric locomotive. Each of these applications could well form a subject for a lengthy treatise in itself. This paper, however, will be confined to a discussion of some of the features of internal combustion engines as applied to mine compressing plants and mill drive. Perhaps at no time in the history of mining in Canada has the search for new mines been more vigorously carried on, more old properties rejuvenated, or more remote districts exploited than during the past three years. The mine operator of today has a far wider range of equipment and facilities at his disposal than had the pioneers of Rossland, Cobalt, or Porcupine. Each year now witnesses the hinterland driven farther and farther back as improved forms of transportation, machinery, and methods make possible the exploration of properties once considered too inaccessible to warrant serious attention. Howey, Sherritt-Gordon, Callinan-Flin Flon, Jackson-Manion, Picard Gold Mines, and a number of properties in British Columbia, afford excellent examples of work carried out on an extensive scale miles from a railway, or in comparatively inaccessible mountain regions.

Jan 1, 1928

By Wang Wenqian, George W. Poling

"Devices and flowsheets for recovering fine placer gold are reviewed. Inefficiencies of gravity processing techniques are documented and discussed. Prospects of combining gravity and froth flotation techniques are presented. Possibilities of using other separation techniques, such as magnetic and electrostatic devices are also discussed.IntroductionSeveral new methods for beneficiating different types of placer ores have been developed in the last two decades. Improved efficiencies in the recovery of fine particles have been achieved by improving gravity flowsheets and machines as well as by developing multiple treatment techniques involving flotation, magnetic and electrostatic separations. Placer gold processing, however, has been an exception to some extent. Gravity concentration using riffled sluices accompanied by mercury amalgamation is still the main method in use today. Because of this, the recoveries of fine gold and the other associated values are often similar to those achieved several decades ago. For example, very few sluice systems recover significant placer gold finer than 100µm in size.Only a few proposals for using alternatives to simple gravity methods for recovering fine placer gold can be found in the published literature. The fixed, low gold price discouraged research in this field for many years. Development of more efficient processes has not kept pace with the recent rapid escalation in the price of gold. Froth flotation for saving fine placer gold might now prove economic, for example. This paper reviews literature published on the recovery of fine placer gold over the period 1907 to 1980. Suggestions for improving the performance in this field, based on the authors' current testwork, are also presented."

Jan 1, 1983

By D. H. d Hamly

THE work of Brown and others at Pittsburgh (Brown, Baum, Yant, and Schrenk, 1938)(1) and the success of their light field microprojector (Figure 1), have shown that the microscopy of dust quantitation can be greatly improved. It has been shown that dark-field microprojection of dust spots on konimeter slides is possible (Pullen, 1940), and this paper is a discussion of the new microprojector and a new counting method which is made practical by this instrument. The microscope makes possible the ready determination of the dustiness of mine ventilation air. Reduction of the dust concentration from a dangerous to a safe level involves one or more of the following: reduction of dust production, filtration of the air stream, or dilution with non-dusty air. Each of these raises important engineering problems of time and costs, and trustworthy information on the state of dustiness of the air is required ?both before and after the employment of any method of reduction. Records of this information may be divided into two broad classes concerned with safety: (1) the level of dustiness, and (2) the quantity and kind of dust produced by a machine under a given set of conditions. Though the first requires only one determination for a given time and place, numerous routine records are required to show the continuous safety of the air in an actively producing mine. Though repeated samples are required, highly accurate counts are not needed to show safety or to indicate whether a substantial increase in the non-dusty ventilation air has produced a proportionate decrease in the dustiness of the mixed air. The Devers and Gathercole konimeters have proved satisfactory instruments for this purpose in Ontario.

Jan 1, 1942