Search Documents

By M. P. Du Plessis

"The paper discusses coal research in relation to the special needs of Western Canada, with its large resources of lignite and subbituminous coals. Research programs are presented under the following headings: Coal Liquefaction, Pyrolysis, Fluidized-Bed Technology, Underground Coal Gasification and Supporting Investigations. Typical processes are presented and their relevance to Canadian coals is described. The longterm plan of the Alberta Research Council for coal research and the steps taken for its implementation are discussed. Finally, some innovative concepts arising from basic research in coal chemistry are discussed.Canada's Coal ResourcesCanada is richly endowed with coal reserves. With estimated ultimate reserves of 600 billion tons in O.76-m (2.5-ft) thick seams under less than 762 m (2500 ft) of overburden, Canada rank s fourth after the USSR, the USA and Chinatu (see Table I) . Canada's reserves are incompletely explored and estimates are constantly being upgraded. Preliminary information from deeper test-hole logs suggest that similar , if not larger, tonnages occur at depths greater than 762 m (2500 ft).The types of Canadian coals and their regional Distribution(2) is shown in Figure 2. Alberta's subbituminous Plains coal represents about 70% of estimated national reserves. A large portion of the coal can be mined at relatively low cost by surface mining techniques, and it is currently being used exclusively for power generation in conventional thermal plants. This coal, however , also represents a large potential .source of liquid fuels which could equal or exceed that of oilsands and heavy oil. Table 3 compares Federal Government estimates for resources and reserves of fossil fuels in Canada and their recoverable oil content or equivalent.A conservation estimate of only the reserves of thermal coal represents an oil equivalent of 27.6 billion barrels , which equals the recoverable reserves of oil-sand bitumen and heavy oil. A more realistic estimate is probably several times this amount. Although coal can be converted to many other end products, such as fuel gas and synthesis gas for hydrogen and ammonia production, liquid fuels remain the most desirable product mainly because they can be transported more cheaply over long distances and their high energy density makes them uniquely suitable as fuels for transport and agriculture."

Jan 1, 1981

By J. Olson

"A model was developed to use near-infrared (NIR) analysis of pulverized ore samples to estimate the recoverable gold content for ores from the Barrick Cortez Hills underground mine. Current routing practices use a ratio of the cyanide soluble gold content and fire assayed gold (CN/FA) to classify ores as oxide or refractory. Prediction accuracy of the NIR model was equivalent to the CN/FA ratio. Prediction accuracy was improved by combining the CN/FA ratio and the NIR spectra. Bootstrap validation estimates the root-mean-square error to be 9.92% with an estimated r-squared value of 0.893. This model will allow more accurate estimates of the variability in recoverable gold content throughout this mine. These data will aid in building an improved geo-metallurgical model or in making better informed routing decisions during the production cycle.INTRODUCTION The contained gold of an ore available for cyanidation is often related to subtle variations in the mineralogy. It is difficult and expensive to collect enough mineralogical information in order to predict how the variable mineralogy will impact the metallurgical results and project economics throughout the life of the mine or mill. Near-infrared spectroscopy may be an effective tool to rapidly and inexpensively collect discrete, quantitative mineralogical data for minerals that contain transition metal oxides, metal sulfides with semi-conduction properties, rare earth metals, and some chemical groups having di-pole covalent bonds such as carbonates, sulfates, and various types of clays (Hunt, 1977). Near-infrared spectroscopy can be a powerful tool for geo-metallurgical characterization of deposits where the presence of these minerals has direct or indirect relationships to metallurgical results such as grindability, regent consumption, or recovery. Near infrared spectroscopy is a rapid analysis that measures the intensity of reflected light in the near-infrared spectrum. The ranges for the ASD-Panalytical units used in this study extend through the visible spectrum and into part of the UV spectrum, reporting reflection by wavelength from between 350 nm to 2500 nm. Absorption peaks visible in this range are a result of interactions with outer valence elections or chemical bonds. The location and intensity of the peaks vary depending on the chemical composition and crystal structure of a solid indicating the presence and abundance certain minerals (Hunt, 1977; Clark, 1984)."

Jan 1, 2017

By P. R. Brito-Parada, A. Norori-McCormac

Positron emission particle tracking (PEPT) has become an important tool for flotation research, as it is able to resolve directly the behaviour of particles in laboratory scale flotation vessels. The first applications of PEPT to flotation showed only the motion of an individual particle in the pulp and the froth, but nonetheless allowed interpretations of behaviour not previously possible. Since then, PEPT measurement and data analysis techniques have improved significantly and now ensure a high level of confidence in the particle behaviour obtained. In particular, statistical analysis of long-duration experiments allows time-averaged data to be collated, ensuring spatial accuracy and allowing rigorous comparison of different conditions. It will be shown that these PEPT techniques can be used to compare directly the effect of operating conditions and particle properties in a laboratory flotation system. Particle tracks will be illustrated, as well as analyses of particle speeds, average flow streamlines and occupancy that show marked differences in behaviour near the interface and impeller.

Jan 1, 2015

By F. Bourgeois, J. -S. Kroll-Rabotin

ABSTRACT: Falcon concentrators are enhanced gravity separators designed for concentrating fine particles. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidization water. We investigated the physics of particle transport inside Falcon concentrators, and concluded that separation efficiency is governed by differential settling velocity. We derived and published a predictive model of the partition function under dilute conditions. We intend to extend the initial model to concentrated ultrafine suspensions for application to industrial scenarios by adding hindered settling to account for solid concentration effects.

Jan 1, 2011

By M. Sukhram, S. A. Argyropoulos

"In the aluminum and steel processing industries there is a need for velocity sensors to measure the flow characteristics of liquid metal. This paper will present a sensor and an inverse heat transfer technique to determine the direction of velocity in flowing liquid aluminum. Experimental research work with the sensor involving liquid aluminum was conducted, using the Revolving Liquid Metal Tank at the University of Toronto, which rotates 50 kg of liquid aluminum with velocities up to 0.35 m/s. Experimental data for various magnitude of velocity demonstrate that the sensor records different thermal profiles under different fluid flow conditions. Using the transient temperature information and the inverse technique, the direction of velocity of the molten aluminum flow field can be inferred. INTRODUCTIONOur research at the University of Toronto has focused on developing invasive sensors to determine the velocity of high temperature liquid metals. High temperature in this setting is defined at VALUES (in excess of 660 °C. The discussion which will persist in this manuscript involves detecting the direction of flow in liquid aluminum using an inverse heat transfer technique. We first reported on the sensor which is used in this article in the following two publications (Sukhram and Argyropoulos, 2011a; Sukhram and Argyropoulos, 2011b). The motivation to perform this research is due to the lack of sensors available to characterize the conditions within a high temperature liquid metal reactor/vessel. A report conducted by The Minerals Metals and Materials Society (TMS Energy 2011) has suggested that the introduction of sensors into molten metal processing environments has the potential to increase process efficiency up to 15%. Such sensors will aid in the understanding of high temperature liquid metal processing operations with the goal to implement more efficient process design and practice."

Jan 1, 2012

By D. Markwart, B. Volk

Anode effects are a phenomenon of the aluminium electrolysis process which produce potent greenhouse gases called PFCs (CF4, C2F6). With concerns surrounding global warming, and increasing regulation of GHG emissions, anode effects have become a significant sustainability issue for aluminium producers. In modem smelters, sophisticated computer control and automated alumina feeding systems allow for very tight control of the alumina concentration in the electrolyte and thus very low anode effect frequencies. Older smelters, however, do not have these systems and must either invest heavily to obtain them, or find other, innovative ways to reduce anode effect frequency. This paper will present the integrated approach to anode effect reduction used in the Vertical Stud Soderberg (VSS) potlines at Kitimat Works. Through an innovative combination of simplified signal analysis, modified alumina feed control logic, anode effect prediction, and anode effect prevention using a pager based communication system, Kitimat W arks has been able to make significant reductions to its anode effect frequency.

Jan 1, 2006

By F. L. Thompson

MAN has been using lubricants of one type or another for at least four thousand years, and probably for a much longer period. We have learned from the inner wall of the tomb of Tehuti-Hetep, on which is a decoration illustrating the method of moving a great stone statue, that as early as 1650 B.C. lubricants were used to facilitate the movement of heavy loads. The Egyptians had available nearly every animal oil and fat, as well as at least thirteen vegetable oils, of our time, all used for food products and in the arts. Examination of the deposit on the axle of a chariot from an Egyptian tomb of 1400 B.C. showed it to consist of animal fat, quartz, sand, iron, and compounds of aluminium and lime-indicating a manufactured lime-soap grease made with lime-soap and possibly tallow. This would not be a bad lubricant for the axles of chariots which had to travel over sandy soil in hot weather. As to the method of grease application, it is remarkable that, from the time wheels were first used in the far distant past up to the present day, no one has ever thought it necessary to design a seal to keep the lubricant in and the dirt out. While time certainly marches on, we have today, in waggons throughout the world, exactly the same form of lubrication as was used in the earliest chariots. From the early days of the chariot until shortly before 1800 A.D. (when the steam engine was introduced), the main heavy equipment required for mining purposes, for machines of war, etc., was made of wood. The bearings were rough, but usually they had metal in the lower half. Light machinery was made of bronze, brass, or iron. Large clearances and poor alignment, plus the fact that speeds were much below present-day demands, combined to provide conditions that were quite satisfactorily met by the lubricants available. These were often produced locally by the machine operator. In northern countries, lard oil, prepared from the fat of hogs, was the universal lubricant employed in machine shop, as a belt and leather dressing, and for cutting operations. Sperm oils were used for light machinery, whereas beef and mutton tallow were more generally employed for the largest bearings. For the early steam cylinders, a slug of heated beef tallow was injected wherever the cylinders gruntingly complained of a lack of lubricant. Southern countries, however, resorted to the use of vegetable oils-olive, cocoanut, etc.

Jan 1, 1940

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By Claudia Gasparrini

"Factors affecting the extraction of gold are of a mineralogical nature. Knowledge of the mineralogy of the ore or metallurgical product to be treated, if appropriately combined with the metallurgical test work, may improve gold recoveries. .This paper outlines the mineralogical techniques f or the study of gold ores and metallurgical products and describes the gold mineralogy in relation to its metallurgy. An effective plan for studying refractory and other difficult ores, combining metallurgical test work, chemical analysis and mineralogy and capable of giving positive results over relatively short periods of time, is suggested.IntroductionFactors affecting gold recoveries are of a mineralogical nature and include (i) the gold-bearing minerals, (ii) their grain size and, particularly where the grain size is very fine (10 microns in diameter and less), (iii) their host minerals and (iv) the association these form with the gold-bearing minerals.Mineralogical studies of gold ores and metallurgical products containing gold in economic amounts (today down to 1/10 of one ounce per tonne or 2.84 ppm) are difficult and time consuming. Mostly because of such reason, metallurgical testing (test work) is usually done simply by trial and error without understanding the causes for failure or success.Mineralogical studies, if appropriately conducted and combined with the test work, provide an efficient mean s of improving recoveries through the understanding of gold losses derived from the use of the wrong technique for separation. The information they provide is therefore the first step in the development of recovery techniques, for those ores where the test work alone failed to produce positive results."

Jan 1, 1983

By J. Peck, F. Brackebusch, M. Scobie

"A number of alternative strategies exist to improve narrow orebody stope productivity and safety through mechanization. Particular attention is given to one of these: the development of an in-stope mining machine. This paper summarizes those characteristics of vein orebodies in Canadian mines which are considered to govern such mining machine design. It then reviews past and current attempts to develop hardrock mining machines which could potentially be applicable to narrow stope widths.IntroductionSerious interest is mounting to exploit new technology in the development of methods and machinery to stope narrow, hardrock, orebodies. The motives relate not only to the foreseen need to maintain or reduce production costs, but also to considerations of manpower availability, safety, ground control, ore recovery and dilution. This also follows the demonstrated success of technology application in larger metal orebody stoping, where machine development has been seen to lead to improved productivity as well as the future prospects of continuous mining systems and eventual automation, e.g. ITH blasthole drill development and bulk mining. This paper deals in particular with machine design for ore fragmentation in narrow, hardrock orebodies. It is considered that such machine design closely interacts with the over-all stoping method design and that both require consideration in parallel to ensure success in mechanization."

Jan 1, 1990

By S. Devereaux, P. Gover, S. Everett

Having real-time data of blast furnace burden profile with respect to burden height and temperature is critical to making informed decisions on blast furnace operation. Given the high temperature and gaseous environment within the blast furnace shaft, traditional instrumentation has been limited at providing the level of real-time feedback information needed to optimize blast furnace operations. Infrared thermal imagery technology provides non-contact temperature measurement across the entire burden profile, allowing for better understanding of the dynamic movement of the burden within the blast furnace shaft. This technology increases blast furnace performance by improving the decision-making process for hour by hour operations. This paper will discuss the development of incorporating infrared thermal imagery technology into the operating strategy of a lead blast furnace.

Jan 1, 2015

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By Kr. N. Karparov

Measurements made with high precision GPS landmarks and geotechnical radar Reutech MSR- 300 associated with the observed movements in the north face of Assarel Mine, where on a horizontal distance of 50 m, 2 groups of landmarks indicated different deformation behavior. Measurements are made in order to confirm the applicability of the radar system in regions of complex geotechnical conditions. The standard deviation of each landmark is used as an accuracy standard between the separate measurements of the deformation vectors made by the high-precision GPS system for each landmark. A very good correlation between the displacement vectors can be seen based on the measurements made with the high-precision GPS system and the measurements made by the radar system MSR-300. Geological, engineering geological and hydro-geological conditions of the area of concern are discussed in this paper. The measured deformations and the FLAC/SLOPE analysis show similar results. In the paper is discussed their local character and their sensitivity to other geotechnical and hydro geological conditions.

Aug 1, 2013

By The Staff

"IntroductionThe difficulties to be overcome in shaft sinking and development at depth are centred at McIntyre in and around No. 12 shaft. Generally they have been due to increasing pressures and temperatures and to changes in geological structure. This paper describes the difficulties and the measures taken to meet them.No. 12 ShaftEarly in 1932 McIntyre decided to sink an internal shaft from the deepest level, the 3875, to explore and develop known veins extending below that horizon. The location selected was a point 1,500 feet south and 1,000 feet east of No. 11 shaft, the main operating shaft through which the men, ore, and most of the materials are handled Shaft and auxiliary equipment we1e laid out for 3,000 feet, that is to 7,000 feet below the surface. The shaft was to be capable of handling 1,500 tons of ore daily from the lowest level, and was to provide ventilation, compressed air, water, and electric power to service all levels.No. 12 is an internal, vertical shaft extending from the 3875 to the 6825 level and bottoming at 7,007 feet. It is a rectangular, four-compartment shaft, 21 ft. 9¾, in. by 6 ft. 3¾ in. outside the timber (Figure 1).There are two hoisting compartments and one airway compartment, each 4 ft. 10¾ in. by 5 ft. ¾ in. inside dimensions, and a combined manway, pipe, and cable compartment 4 ft. ¼ in. by 5 ft. ¾ in. Levels have been established at 150-foot intervals, pump stations and sumps at 1,000-foot intervals, and. there are two loading pockets, one at the 5525 and the other at the 6900 level.The shaft was sunk in two stages. The first stage, consisting of preparation above the 3875 level and sinking to 5585 feet, was completed by March 31st, 1935. The second stage of deepening the shaft from 5,585 to 7,007 feet was started August lst, 1946, and completed three years later."

Jan 1, 1950

By Y. M. Shneerson, V. M/ Shpaer, E. E. Zhmarin, A. Y. Lapin, E. M. Vigdorchik

This paper describes studies of zinc concentrate oxidizing pressure leaching using the method of mathematical modeling. The concept of a kinetic function was taken as a basis for mathematical modeling of the leaching process. The kinetic function describes dependence of the unreacted component share OJ on the relative time x (the relative time is the ratio of the test duration and the time of complete dissolution). This kinetic function is determined in accordance with the results of batch laboratory tests. The laboratory tests have been carried out on zinc concentrate produced from Kazakhstan zinc-copper ores. Zinc concentrate consisted mainly of three types of minerals: sphalerite (70%), pyrite (13%) and chalcopyrite (10%). Oxidation reactions of sphalerite, pyrite and chalcopyrite have been considered as principal ones. The kinetic characteristics of the process (kinetic function, reaction order, activation energy, duration of complete dissolution of the concentrate components) have been calculated in the course of laboratory tests. The mathematical model was used for estimation of the main technological leaching process parameters (such as process rate, degree of metals extraction, autoclave capacity, heat balance, etc.). Mathematical modeling based on the kinetic function concept allows safe designing of metallurgical equipment and scaling the technology to industrial capacity.

Jan 1, 2004

By R. M. BUCHANAN

The segment of Canadian industry based on smelting of alum in um and manufacture of consumer products is based entirely on imported alumina and bauxite. In the absence of Canadian bauxite deposits, consideration of anorthosite, a less desirable aluminous rock, is being undertaken as one alternative in maintaining assurance of supply. Anorthosites in Canada cover many thousands of square kilometres of the Precambrian Shield. Although compositions vary widely among Canadian anorthosites, many appear to exceed the specified minimum of 25% A I 20 3 in bodies containing more than the required JOO million tonnes. A lthough most Canadian anorthosites are of Precambrian age, one located in British Columbia has been identified as being Middle _Cretaceous.

Jan 1, 1984

By P. E. Cavanagh

"The Davis tube test has been used for many years as a laboratory method for determining the magnetic iron re-coverable from a magnetite iron orebody. This paper de-scribes a method for determining the recoverable iron from ores of the Labrador Trough type, with the usua1 flow sheet utilizing spirals followed by magnetic separation.The mechanical structure of a metamorphosed iron ore, resulting from recrystallization over long periods of time, is the basis for the laboratory method developed. Similarities between the structures of such recrystallized ores and the structure of annealed and recrystallized steel are noted.A laboratory technique to determine the size of the different grains of gangue and iron ore minerals is de-scribed and the application of this information to arrive at recommended grinding techniques and flow sheets is demonstrated. The use of the method to determine recoverable iron in such ores is compared to actual iron recovery in the pilot-plant and commercial concentrations of the same ore.The use of a specified lower limit of recoverable iron as determined by this method, in order to design open-pit limits, achieves practical results when compared to designing a pit based on an arbitrary lower limit of total soluble iron. The Ungava Iron Ore deposits are used in giving an example of the resulting pit design changes."

Jan 1, 1968

By T. E. Morimoto

Summary The Research Council of Alberta has made a series of tests with the cyclone washer to investigate the influence of the following operating variables: underflow apex diameter, .specific gravity of medium, pulp ratio, density distribution of the feed, and size analysis of the feed. The results obtained for all the variables studied, except size analysis of the feed, are included in this paper. The tests were made with smaller underflow apex diameters and lower specific gravity .suspensions than have been recommended by Cerchar for the sharpest separations. However, what is considered to be sufficiently good cleaning was accomplished with a suspension of 1.30 specific gravity and an underflow to overflow diameter ratio of 0.56. It was found that the sharpness of separation was not affected appreciably by variations in specific gravity of suspension or underflow apex diameter provided that the density of separation was within the normal range of washery operation. Cyclone performance was not too adversely affected by decreasing the pulp ratio. The minimum figure which gave reasonable separation was 4 to 1. The tests with various density distributions of feed revealed .that the degree of washing difficulty had no detrimental effect on the .sharpness of separation given by the cyclone. Introduction A major problem of the bituminous coal industry today is that of reducing the ash content of the finer sizes (minus 1/4-inch) of coal. This problem is particularly acute in Alberta, where, because of tectonic movement subsequent to deposition, the coals have been rendered friable, and bands of impurities have been intimately mixed with the clean material. As a consequence, most Alberta coals, as mined, contain a large proportion of fines and have a high inherent mineral-matter content. The advent of mechanized mining and stripping operations ?has further aggravated this problem.

Jan 1, 1952

By Atsushi Sainoki

Blast vibration induced by mining activities, such as stope production blasts, could lead to the initiation of seismic events that inflict damage to mine openings. In this paper, the effect of stope production blasts on nearby fault is examined. First, validation of blast vibration attenuation is performed with a numerical model representing a single blast hole through comparison with that calculated from charge-weight scaling law derived from in-situ data. Subsequently, a mine-wide scale model with a fault parallel to a steeply dipping, tabular ore deposit that is mined out with sublevel stoping method is generated, and the stopes are extracted and backfilled with static analysis to simulate burst-prone conditions on the fault. Based on the stress states, dynamic analysis is performed, in which blast vibration is applied to grid points on a stope wall on the hanging wall side. This assumes 9 blast holes located close to the wall, and blast-induced particle velocities that consider the positional relationships between the assumed blast holes and the stope wall are applied. During the dynamic analysis, blast sequence is considered, and stress states and shear displacement on the faults are examined. It is found from results that, after a rise in normal stress on the fault due to compressive waves induced by the blasts, the normal stress decreases because of the reflection of the compressive waves on the fault. The reduction in the normal stress due to the reflected waves is found to be large enough to cause the fault to slip. The results also show that the level of normal stress eventually keeps decreasing with time as the blast sequence proceeds and that an increase in shear displacement on the fault is accompanied by a decrease in normal stress. This study clarifies the mechanism by which blast vibration causes the fault to slip. In addition, the simulation technique to apply blast vibration that takes into account blast sequence and the locations of blast holes to a stope wall is developed.

Aug 1, 2013