Search Documents

By E. V. Konopleva, H. J. McQueen

"The isothermal bainite transformation kinetics of low- and medium-carbon alloy steels after hot deformation and the rmocycling treatment (TC) has been studied by the magneto - metric method. Deformation was produced by rolling at 800°C-1000°C. TC included three cycles of rapid (30°C/s) electro-heating up to 900°C-1000°C followed by quenching.Hot deformation retards bainite transformation in the lower part of bainite range (<400°C) and accelerates it in the upper part (>400°C). The effect is greater for higher strain and lower deformation temperature. Deformation also diminishes the overall bainite fraction below 400°C and increases the completeness of reaction above 400°C.Thermocycling provides more uniform ultrafine austenite grains with average size of 3 µm -4 µm compared to 12 µm -14 µm after conventional heating. The transformation rate after TC was almost the same as after conventional heating in low-carbon steel but was faster in medium-carbon with no change in the completeness of reaction. The degree of acceleration increased with rise of transformation temperature.There are a number of factors which are responsible for a change in bainite transformation kinetics in austenite deformed at high temperatures or subjected to TC. One of the most important factors is the refinement of structure, another one is structural and chemical inhomogenity of austenite due to deformation or to rapid heating. To estimate the contribution of these factors, ?-transformation was studied after different austenitizing conditions (low-temperature heating at 850°C- 950°C; high-temperature heating at 1100°C; step treatment – austenitizing at 1100°C, then cooling to 950°C-850°C). The results obtained make it possible to conclude that the structural and chemical inhomogeneity of austenite activate the bainite reaction while the grain refinement retards it. Intensity of the effect produced by each factor depends strongly on the steel composition."

Jan 1, 1997

By A. Bauer

This paper describes the trends in recent years in explosives formulated to produce larger blast-hole spacings and over-all lower drilling and blasting costs in hard formations. A consideration of current rotary drilling costs per ft of hole and per ton of muck versus hole diameter indicates that it is now possible that we shall see much further use of lower-energy-content, lower-cost slurries and dry mixes, and larger-diameter and, in many instances, cheaper blast holes. These will be drilled on current or slightly larger blast patterns to yield the same energy input per ton of rock and similar fragmentation at lower costs.

Jan 1, 1968

By J. K. Shaw

The science of low temperature engineering is well entrenched in mining. Uses for common cryogens, including liquid oxygen (LOX), liquid nitrogen (LN2), and liquefied natural gas (LNG) in the gas and minerals industries are reviewed. Potential future applications are discussed within the scope of mining, particularly in refrigeration and ventilation. The second part of this paper focuses on the Linde cycle, which is at the heart of most liquefaction plants. Steady state equations describing the mass and energy flows are presented. The paper concludes by explaining the concept of a wind powered Linde- Hampson cryogenic cycle and assessing, with scoping calculations, the technological feasibility of producing cryogens with an intermittent source of (renewable) energy.

Aug 1, 2013

By P. C. Benedict

Introduction and Summary The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, district of Thunder Bay, Ontario. Production started in March, 1934, and terminated in September, 1941. During this period, the mill treated 425,866 tons of ore, from which 153,103 ounces of gold were recovered. The lowest level from which ore was mined was the 1900, but considerable drifting was performed on the 2075 level and 800 feet on the 2415, the deepest level. The following description of the geology of the mine is recorded by the senior author but is based on the observations and complementary mapping of both authors. The vein strikes about N.72°E. and has an average dip of 80°S. (Figure 1). In stoped sections, the quartz averaged about two feet wide. On the 1725 level it was drifted on continuously for more than 7,000 feet, but in the mine as a whole practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section but not much beyond its limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth. It may be generalized, from top to bottom, as light grey to dark grey to brownish. The brownish quartz first appeared near the bottom of the ore.

Jan 1, 1947

By G. E. Viens, R. A. Campbell, G. N. Banks

A survey of the literature reveals wide differences in the procedures used in making iron ore pellets and in the properties of the pellets obtained. In this paper, the methods of production and the properties of pellets, as reported in the literature, are examined in an effort to determine what correlations exist between them. An attempt is also made to determine the levels of the properties of pellets which are considered acceptable and desirable in modern practice. M UCH has been written regarding the important changes which have been taking place recently in the iron ore industry. As the demand for ore has increased and the supply of direct-shipping ore has dwindled, tl1e problems associated with the utilization of lower grade ores ha\•e been intensely investigated and important advances in both beneficiation and agglomeration techniques have taken place. In particular, there has been a great deal of activity in connection with the pelletizing method of agglomeration. The superiority of pellets over raw ore has been demonstrated in blast furnace tests

Jan 1, 1962

By Bruce A. McFarlane

"I WOULD LIKE TO SAY how honoured I am that I have been invited to participate in this panel discussion. I have taken the liberty of narrowing my topic somewhat so that instead of speaking on the Sociology of Professions as a whole I will speak on one aspect of it, that is, on Manpower Problems in the Minerals industry of Canada, with some reference to a new social role for the professionals engaged in this industry. This probably means that I will be encroaching on areas covered or to be covered by other speakers, but I hope that when I do so I will do so from a slightly different vantage point. That is, from a sociological perspective rather than from a historical, industrial, business or professional perspective. I plan to divide my discussion into three areas, namely: (i) problems of ownership and control; (ii) environmental problems; and (iii) manpower and recruitment problems. I do not plan nor am I able to provide clear-cut solutions to the various problems I raise under these three headings. Rather, I hope that my discussion of the problems may form the basis for an extended discussion here and elsewhere. Because of the limitations of time, I will only briefly discuss the first two problem areas noted above – (i) ownership and control and (ii) environmental problems - and I plan to concentrate on the manpower issue."

Jan 1, 1972

By Douglas R. Piteau

"Assessing the stability of a slope cut in rock is basically a problem of engineering geology - geology, because it involves a sound understanding of the important aspects of geology, such as geological structure, ground water, weathering and other natural phenomena, which all relate to or exist in a geological environment, and engineering, in that quantitative evaluations and calculations are necessary, these being based on mechanics and relating to the strength of the geological materials and the forces causing instability of the slopes. The engineering geologist must make every attempt to. provide, in a quantitative way, information on those geological factors which are necessary for making calculations of the probable stability of the slope. These include numerical assessments of quantities relating to the characteristics of structural discontinuities, rock types, topography, hydrogeology, tectonic history and other environmental factors. Based on the development and extension of these general principles, both preliminary and final slope stability studies of some open pits in South Africa, Swaziland and Zambia have been conducted. Some of the basic concepts and techniques developed to carry these studies out are described."

Jan 1, 1972

By S. J. Prout, J. M. Lang, D. Lascelles, K. Sarinas

"There is a growing demand for ore characterization methods to support metallurgical development programs from a true geometallurgical perspective. Today, there are multiple automated mineral analysis systems on the market, many of which are based on conventional mineral liberation data. However, liberation data can be limited when assessing the floatability of a mineral to predict its recovery as it doesn’t consider the surface area available for collector absorption and bubble attachment; whereas mineral exposure measurements can. Using the First-Order Rate equation to predict the recovery versus time of variously exposed particles, a model has been developed to predict the recovery of copper sulphides at a particular grind size. This model provides the opportunity for the prediction of copper recovery and grade from multiple, small-scale samples. These predicted values can be imported into resource modeling software, and guide the domaining of geometallurgical units within the ore body. Data has been analyzed from various global copper porphyry systems and compared with actual flotation testwork.IntroductionAs part of the development of a mining project, resource estimation primarily focuses on the definition of the quantity and grade of the ore in the deposit; as the project evolves from preliminary economic assessment through to feasibility, the geological model is usually further populated with hardness and recovery data.The CIM Definition Standards (2011) identifies measured mineral resource as the part of a mineral resource for which quantity, grade or quality, densities, shape, and physical characteristics are estimated with confidence sufficient to allow the application of “modifying factors” to support detailed mine planning and final evaluation of the economic viability of the deposit as an asset. The modifying factors include, but are not restricted to, mining, processing, metallurgical, infrastructure, economic, marketing, legal, environmental, social and governmental factors.With market fluctuations, many investors in the mining industry have become more and more risk averse which has increased the demand for more reliable data to support these modifying factors. This has led to the widespread use of geometallurgy and statistical analysis to better inform the resource estimation. Geometallurgy is used to characterize ore variability and is especially useful for highly variable or strongly zoned deposits, several close deposits that will be milled together, projects requiring complex or new metallurgical approaches, brownfields or sight-of-mine exploration, expansion projects that exploit new, deeper or adjacent reserves, and projects with significant legacy drill core that are being re-evaluated due to new economic circumstances."

Jan 1, 2018

By Rod Maclean, George Stewart

"This paper covers the planning, development, and mining of an underground pillar complex using a bulk mining method. To achieve the long-term goal of continually improving our operating processes, all cut-and-fill and undercut-and-fill workplaces at Thompson Mine have been evaluated for their conversion potential to the bulk method referred to as VerticalBlock Mining (V.B.M.).Since December 1979, conversion has occurred to the extent where 80% of the ore hoisted is mined using Vertical Block Mining (V.B.M.).Productivity and profitability have been substantially improved by converting to this bulk method, especially in pillar areas.IntroductionThompson Mine is a 6000 ton per day underground nickel mine located 3 miles outside the City of Thompson, 400 air miles north of Winnipeg . The mine has two shafts, T-l and T-3 (Fig. 1). The T-l shaft is 4427 feet deep with the deepest mining taking place on 4000 level. The T-3 shaft, which is the area of this presentation, extends to a depth of 2607 ft with the deepest operating level at 2400 ft. The two shafts, some 10 000 ft apart, are connected underground on numerous levels. The ore mined at T-3 is trammed on 2400 level to the T-I main ore pass and hoisted through the T-l shaft. Eight hundred and fifty thousand cubic feet of fresh air per minute ventilates the mine.The 1400 level 310 pillar complex is located in the T-3 mine area. There are six rib pillars, two crown pillars and one main pillar (boundary pillar between cut-and-fill stopes) within the complex (Fig. 2). The majority of the ore in this area has been mined using mechanized cut-and-fill techniques .Undercut-and-fill mining was the method originally planned to recover these pillars. It is slow, labour-intensive, and requires extensive use of timber during the mining cycle. The extraction drifts in the area are heavily timbered due to their proximity to the ore and the age of the facilities. Increasing drift maintenance costs and the successful mining of two main pillars with V.8.M. techniques provided the stimulus to review the mining plans for this area."

Jan 1, 1988

By J. Pontt

Gearless mill drives (GMD) offer high performance for torque and speed control for grinding mills and have been applied successfully in modern concentrators for wet grinding with mill diameters from 34 to 40-feet. It is considered a mature technology. However, recently, some large GMD?s have presented unexpected failures in stator and rotor subsystems. The phenomena involved in such failures has shown a complex nature and surprised users and manufacturers. The manifestation of such failures has been observed as mechanical damages to certain components of ring motors. This paper presents a discussion on the electromagnetic forces that can generate stresses in the electrical ring motor that can produce failures and outages. Guidelines for further research and contributions to improved reliability of GMD?s are proposed.

Jan 1, 2012

By John A. Teeter

"A SHORT WHILE AGO I enquired about The Mining Society of Nova Scotia. In all honesty I was apprehensive about addressing such a body if it was highly geared to the technical aspects of discovering and obtaining mineral resources. I was told that this would not be the case. Rather, there would likely be in attendance a broad cross section of people from business, industry and government and from across Canada and the U.S.A. Thus there would be an interest in a free-wheeling discussion of the prospects for industrial development in Cape Breton. Accordingly - being one who hates to miss an opportunity - I intend to exploit the invitation of your executive by being, over the next short while, frankly promotional. I would like to talk about what I consider to be some of the most important attributes of Cape Breton for industrial development and identify some of those prospects. Secondly, I will quickly review some of the things the Cape Breton Development Corporation is doing these days to stimulate some of that industrial development."

Jan 1, 1972

By The Satff

"TEXADA Island is situated in the Strait of Georgia, about 100 miles northwest of Vancouver. The property of Texada Mines Ltd. lies on the southwest coast of the northern end of the Island. A part of the ""Sunshine Coast,"" the climate is moderate, with about 30 inches of rain during winter months and relatively dry summers. Texada has been shipping high-grade magnetite concentrate continuously since 1952 to Japanese ore buyers. In 1959, a 3,000-foot tunnel was driven just above sea level to explore the possible downward extension of known orebodies then being mined by open pit. In January of 1961, because the open-pit operations had a limited life, C. C. Huston and Associates were brought in as mining consultants to do a feasibility study on the possibility of going underground for production. This study was completed in March, 1961. With the completion of the report, the Company went to Japan seeking a ,long-term contract to justify the capital outlay necessary for setting up an underground operation. Concurrently, underground diamond drilling revealed more ore, and the Company planned some modifications to the concentrator for increasing the copper recovery. By November, 1961, a ten-year contract was signed with Japanese ore buyers for the sale of 450,-000 long tons of concentrates beginning in October, 1963. Since that time, the Company has built its own 65 000-ton ore carrier and an additional three-year contract has been negotiated, with an annual tonnage increase of from 450,000 to 550,000 tons."

Jan 1, 1967

By D. M. Ramsey

HIGH-INTENSITY magnetic separation as now practised in the commercial treatment of a large variety of industrial minerals is a com-paratively recent development, having had its practical beginning about ten years ago when it became necessary to devise more effective methods for the purification of the electric furnace abrasives and refractories-silicon carbide and fused aluminium oxide. The fundamentals of magnetic separation are, of course, very well under-stood; bur while very, very old in principle, the process has, in recent years, been developed to a point of far greater usefulness than heretofore. In fact, until the development of the high-intensity process,. magnetic separation was limited largely to the removal of tramp iron? with magnetic pulleys and the removal of the very highly magnetic portions of industrial minerals by means of horizontal conveyor-belt-type separators. All magnetic separation processes depend for their success on the fact that various materials are kinetically influenced to a greater or lesser degree by the force that we speak of as &apos;magnetism&apos;. We have now come to regard &apos;magnetic separation&apos; and &apos;high-intensity magnetic separation&apos; as two different and distinct methods. However, both depend upon the reaction of a particle when placed in a magnetic field. The common types of magnetic separators quite generally operate on the principle that a magnetic particle can be lifted by a powerful magnetic force from a stream of material moving on a belt or other type of conveyor. The application of the force removing magnetic material by this scheme is directly opposed to the force of gravity and is, therefore, limited to sub-stances of a relatively high order of magnetic susceptibility, such as metallic iron and magnetite. Until a few years ago, one very important principle was almost entirely overlooked. Practically every substance is susceptible to some extent, at least, to magnetic attraction, and by the application of a magnetic force great enough, and properly applied, separations of materials heretofore considered &apos;non-magnetic&apos; can be accomplished.

Jan 1, 1937

By Andre Panteleyev, Charels S. Ney, John M. Anderson

"Sam Goosly prospect, 22 miles southeast of Houston, B.C., was discovered in 1967 through geochemical reconnaissance. Soil sampling interpreted with respect to an east-to-west ice movement led to drilling targets.Mineralization is in a window of rocks thought to be Hazelton Group surrounded by Tertiary volcanic rocks and intruded by two stocks separated by about one mile. A westerly quartz monzonite stock is dated 61.1 m.y. and an easterly gabbro-monzonite complex is dated 52.5 m.y. The Tertiary volcanics are trachyandesites shown by the B.C. Department of Mines and Petroleum Resources to be in part extrusive equivalents of the gabbro, and they overlie Hazelton rocks uncomformably. Copper-molybdenum mineralization is sparsely developed in the westerly stock. Silver-copper mineralization forms an elongate west-dipping slab between the stocks in Hazelton rocks, which are continuously pyritized. The gabbro stock is not mineralized, but some dikes related to it are slightly so. Tertiary rocks are pyritized, but are not known to carry copper-silver mineralization. Hazelton rocks are divided into a lower conglomerate, an intermediate pyroclastic unit and an upper mainly sedimentary unit. They form a west-facing homocline. Coppersilver mineralization resides in the pyroclastic unit, mainly in a massive dust tuff through which are lenticular units of lapilli tuff. Well-mineralized rock is typically a breccia of light fragments in a dark chlorite-sulphide matrix. Sulphides are pyrite, chakopyrite and locally pyrrhotite, with very minor tetrahedrite, s phalerite and other sulphosalts. Rock alteration is predominantly a pervasive pyrite-sericite type, with widespread tourmaline, scorzalite, gypsum, ankerite and traces of fluorite. The most evident control of the copper-silver mineralization is the gross parallelism, over a strike length of 1.5 miles, to Hazelton strata, particularly a massive dust .tuff unit. In detail, mineralization crosscuts bedding and there is no appreciable banding within sulphides . A strictly syngenetic origin is untenable, but some initial concentration in a volcanogenic environment with subsequent modification by thermal processes seems likely."

Jan 1, 1972

By Farzad Khodabakhshi, Adrian P. Gerlich

"Multi-pass friction stir processing (FSP) was performed to fabricate a new Al-Mg-Graphene nanocomposite. Microstructural developments and distribution of graphene were studied by using electron backscattering diffraction (EBSD) and transmission electron microscopy (TEM) analysis. In the stirred zone (SZ), grain structure was refined down to about 2 µm attributing to the operative dynamic restoration mechanisms and the locking effect of graphene phase. As a result, the yield strength of Al-Mg alloy was improved more than two times due to incorporation of graphene nano-sheets. Also, the indentation hardness resistance of nanocomposite was increased up to ~60%.INTRODUCTION Aluminum-matrix nanocomposites have garnered significant in recent years due to their superior performance and potential advantages for several industrial applications including the automotive and aerospace sectors. Among various reinforcing nano-materials, carbon-based structures featuring sp2 or sp3 hybridization bonds have been found to offer considerably improved physical and mechanical properties. Such carbon allotropes form at micro- and nano-scales including; graphite, carbon nano-tube (CNT), nano-fiber, and graphene. The potential of two-dimensional (2D) carbon materials was introduced in 2004, with the development of graphene as an alternate 2D allotropic form of the carbon structure with a honey-comb lattice at the atomic-scale. It has been shown that it is currently among the strongest materials ever tested with an intrinsic tensile strength of 130 GPa and Young’s modulus of 1000 GPa, and also offers unique thermal and electrical properties.To fabricate metal-matrix nanocomposites reinforced by graphene nano-sheets with typical metallurgical processing techniques, some attempts have been reported in the literature for various solid-state techniques including; hot rolling, mechanical alloying, and friction stir processing (FSP) of pre-cast plates or surface dispersed graphene oxides. The main challenge in those methods was to facilitate the considerable high temperature and pressure for attaining a uniform dispersion of the nano-sheets during the consolidation process. In most cases, significant difficulties have been reported in obtaining a uniform dispersion of graphene within the metal matrix. Among various techniques for production of metal-matrix nanocomposites, FSP has attracted significant attention as a method of surface modification since it was first reported by Mishra et al. In this process, a non-consumable rotating tool is plunged into the surface of material for the aim of microstructure modification. Extreme material plasticity is induced without melting as a result of friction between the tool and workpiece. Frictional heating and severe plastic deformation induced by the FSP process enables metal matrix nanocomposite fabrication by softening the base material and mechanical stirring to disperse the reinforcing nano-materials into the matrix."

Jan 1, 2017

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively. INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By I. Murray, N. Geoffroy

"Buried pipelines, tanks and other similar equipment are almost always present on large scale industrial sites, including in the oil and gas fields. However, as the proverb “out of sight, out of mind” suggests, it is easy to overlook proper maintenance procedures and simply assume that corrosion protection measures in place are working correctly. Unfortunately, this is not always the case, leading to significant environmental damage and loss of production. This paper describes several cases from various industries where buried equipment failed because of corrosion, sometimes with catastrophic results. It also presents various strategies, based on experience and new research, to help predict and prevent damage to underground metallic structures.INTRODUCTION Metallic underground structures are extremely common in industrial and commercial settings for numerous reasons. Burying pipes, tanks, wires and other similar equipment has numerous advantages: it provides significant protection from mechanical damage, frees up ground space that can be used for other purposes, requires little to no support structure and is generally more esthetically pleasing. However, this last benefit can also be considered the most significant disadvantage of underground equipment: becoming invisible and forgotten. While every engineer is aware of the importance of preventive maintenance, it is also human nature to somewhat forget about equipment that is hard to inspect and assume that everything is fine. This is unfortunately not always the case and failures in industrial settings can have extremely serious consequences. While economic aspects immediately come to mind (loss of production, cleanup cost, etc.), failure of underground equipment also results in an environmental and therefore public relations nightmare, especially in the oil and gas field. Leaks that would have been considered negligible in the past can now make national headlines and perfect reliability, while probably impossible to achieve, is now the goal of most companies. While environmental damage (real or perceived) is most often associated with leaks in the oil and gas industry, it can also affect the mining world. For example, the authors have worked on a project where a buried slurry pipeline had ruptured in the ground, causing a release of perfectly inert tailings. While the economic loss was low, the leak was reported in local media and caused a public relations problem."

Jan 1, 2017

By A. M. L. Cushing, S. Kelebek

Presently, adsorption is one of the effective methods of removing toxic contaminants from waste waters. The contaminants from metal mining industrial operations include an effluent water containing various types of heavy metal species at concentrations beyond the maximum allowable limits, which are 0.5 ppm and 0.3 ppm for nickel and copper species, respectively. Adsorption behavior of copper ions pre-chelated with diethylenetriamine (DETA) and triethylenetetramine (TETA) onto natural bentonite and peat has been investigated. Both natural bentonite and peat was found to be capable of removing these copper-polyamine complexes from aqueous solutions relevant to process water effluents. However, the adsorption capacity of bentonite was significantly higher than that of peat. Two models were used to study the adsorption kinetics: a pseudo-first-order rate expression and a pseudo-second-order rate expression. For both adsorbents, the data conformed best to the pseudo-second-order rate expression. Representation of the experimental data through adsorption models was also investigated. Out of the four cases considered, namely, Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherms, it was found that for both bentonite and peat, the copper polyamine adsorption data conformed best to the Dubinin-Radushkevich adsorption model. The Langmuir model also represents the bentonite-copper polyamine adsorption system reasonably well as the second best case, suggesting that the amount adsorbed on bentonite might be a monolayer with strong affinity.

Jan 1, 2015

By E. M. Timoshenko, A. V. Tarasov

The results of laboratory, bench-scale and semi-commercial investigations of a method for adding surfactant (technical-grade lignosulphonate) to the process of pressure leaching of nickel-containing pyrrhotite concentrates have been discussed. Lt has been demonstrated that feeding of technical-grade lignosulphonate distributed along the length of an autoclave ensures a reduction in its requirement by a factor of 1.5 to 2 as compared with single-point feeding; it also results in a decrease by 5% in the unit requirement of metallized iron-bearing precipitator in the process of non-ferrous metals precipitation and reduces by 0.05 to 0.1% (abs.) the nickel and copper contents in the tailings of the given process. Technical solutions have been proposed for commercial introduction of the process.

Jan 1, 2004

By A. G. Eccles

Western Mines&apos; milling circuit produces three concentrates (copper, lead and zinc), with the tailings being disposed of at the bottom of Buttle Lake. In view of the mine&apos;s location and the method of tailing disposal, a comprehensive pollution control program has been in effect since start-up. Changes -in the ore over the past few years have required the use of increasing quantities of sodium cyanide in order to effect a good copper-lead separation. This led to the use of alkaline chlorination for destruction of ?residual cyanide and precipitation of dissolved copper contained in the tailing effluent. The development of Western Mines&apos; alkaline chlorination plant is discussed in detail, including initial test work and the evolution of procedures leading to the present operation. The current monitoring program is also reviewed.

Jan 1, 1977