Search Documents

By Q. Chen, J. H. Zhang, M. Zhang, F. M. Zheng, Y. J. Zhang

The characteristics of air bubbles and gas dispersion in KYF flotation cell are studied using the method of the point conductivity probe and CFD simulation. With increasing of speed, the velocities of air bubbles increase slowly and the distribution of diameters exhibits little change. With increasing of aeration rate, the gas holdup is increased. However, the velocities and diameters of bubbles have no great change. The CFD predictions on gas holdup have good agreement with the experiment results. The gas holdup distribution in the center section is revealed. The gas dispersion in the middle and upper part of flotation cell is uniform. It would be helpful for bubbles and solid particles collision. The gas holdup of the lower part of flotation cell is scarce, and it agrees with the observation in experiment. The gas would accumulate at the suction side of impeller blades, and it would decrease the power consumption. The rotating speed and aeration rate have great effect on gas dispersion. With increasing of aeration rate, the gas holdup of flotation cell will increase. The increasing of speed would improve gas dispersion. The results are expected to help to optimize the performances of KYF flotation cell.

Jan 1, 2015

By W. McCombe, G. Remple, L. Zunti, M. Bernardin, L. Nightingale-Mercer

"The McClean Lake Mill is located approximately 700 kilometres north of Saskatoon, Saskatchewan, Canada and is operated by AREVA Resources Canada Inc. (AREVA). The mill was designed to process high grade uranium ores, and has been undergoing a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to processing high grade ores from the Cigar Lake Mine. During the metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit have a propensity to generate hydrogen gas during acid leaching. Hydrogen is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit. Uranium processing is further complicated by the fact that an oxidant in the form of oxygen gas or hydrogen peroxide is required to regenerate iron in the leach, which further increases the risk from hydrogen gas. During 2013 Hatch and AREVA designed and engineered a number of novel upgrades for the leaching circuit to mitigate the risk of hydrogen gas evolution in the process. Best in class technology was utilized in addition to control and operating strategy changes to ensure the leaching circuit can be safely operated with ores that can evolve hydrogen gas. This paper reviews the design concepts and modifications implemented on this unique and challenging project.INTRODUCTION The McClean Lake mill was originally designed to process high grade uranium ores, however until 2014 the average ore grade processed was 1%. The facility has been undergoing a multiyear upgrade and expansion to increase its production capacity from 12 to 24 Mlbs U3O8 per annum, while also undergoing upgrades to allow it to safely transition to new high grade ores, averaging 18% U, from the Cigar Lake Mine. During the last round of metallurgical test work on the Cigar Lake ores, it was identified that some ore zones in the Cigar Lake deposit had a higher propensity to generate hydrogen gas during acid leaching than previous test work had indicated. Hydrogen gas is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit."

Jan 1, 2017

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities for the nickel industry, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTION The process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic. A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities. These suggestions are particularly applicable to the nickel industry, where the majority of our firm’s prior hydrometallurgical experience was obtained. This paper is an update to an earlier publication (Martin, 2004), offering an opportunity for a new generation of metallurgists and engineers to learn the specialist requirements of pilot- and demonstration-scale plant design, which are key functions in the development and commercialization of new processes."

Jan 1, 2017

By Trang T. Tran-Valade

With continually increasing energy prices, the mining industry has been on the search for new energy optimization technologies. One area that is garnering great interest is Ventilation-On-Demand (VOD). Prior to selection and implementation of a VOD solution, it is important to fully understand the mine requirements as well as its existing infrastructure and the interaction with other automation in place at the site. With this information, a business case can be generated including a cost versus benefit comparison for various control strategies. To assist in the development of the business case, this paper will identify key areas for consideration and recommendations for an implementation plan.

May 1, 2013

By A-A. Bogno, M. Rappaz, J. Valloton, H. Henein

"Rapid solidification of Al-Cu droplets of eutectic composition was carried out using Impulse Atomization in an argon atmosphere, to study the microstructures forming at different cooling rates and undercoolings. Two distinct morphologies were observed within the investigated Al-33wt%Cu droplets microstructures: (i) A regular lamellar morphology and (ii) an undulated morphology. The volume fraction of each type of morphology was measured as a function of the droplet size and the nucleation undercooling was deduced using the hypercooling limit equation. The scale of the microstructures was determined through measurements of inter-lamellar spacing across and along the growth direction. Growth velocity and undercooling were deduced using Jackson and Hunt (1966) eutectic growth theory. Finally, mechanical properties were estimated through micro-hardness analysis using a Vickers hardness tester, revealing exceptional properties for an aluminum-copper alloy. Indeed, the hardness values, increasing with growth rate and undercooling, were 3 times higher than the values obtained in hypo-eutectic Al-Cu alloys.INTRODUCTION Eutectic alloys are very attractive due to their good fluidity allowing ready shaping of parts in casting processes as well as in thermal spray deposition. In addition, they yield microstructures with high mechanical properties, by the virtue of their scale/size which is defined by the solidification parameters and the thermodynamic and thermophysical properties of the given alloy. Therefore, it is important to understand the relationship between the microstructures and the solidification parameters of eutectic alloys in order to control their solidification path and mechanical properties. The latter could be improved by either adding an appropriate strengthening component to a base eutectic material (Böyük, MaraslI, Kaya, ÇadIrlI, & Keslioglu, 2009) or by refining the microstructures for more effective dislocation pinning (Campbell & Campbell, 2003). Tailoring the microstructure can also be beneficial to chemical (Freitas, Osório, Spinelli, & Garcia, 2014; Osório, Freire, Caram, & Garcia, 2012) or electrical (Kaya, 2012) properties of the material. Eutectic-type microstructures, usually formed from liquid (eutectic transformation) or solid (eutectoid transformation), are made up of two or more different phases, generally of lamellar or fibrous (rod like) morphologies (Kurz & Fisher, 1998). In general, a binary eutectic structure can be regular (when both phases are non-faceted) or irregular (one of the two phases is faceted), the two solid phases having roughly the composition of the liquid from which they are formed."

Jan 1, 2017

By Rosie Moore, Harvey Keats, Kerry Sparkes, A. J. Naldrett

"Abstract-The Voisey’s Bay Ni-Cu-Co deposit was discovered in late 1994 as the result of prospecting initiated in the summer of 1993. By July 1995, proven mineable reserves were 31.7 x 106 tonnes grading 2.83% Ni, 1.68% Cu and 0.12% Co, and current total resources in all categories are quoted to be in the order of 150 X 106 tonnes. The deposit is associated with a body of troctolite belonging to the Nain Anorthosite (1.35 Ga - 1.29 Ga) suite, which was emplaced across the boundary between the Proterozoic "Rae" Province to the west and Archean "Nain" Province to the east.The deposit can be described in terms of three geological settings. The "Ovoid" is a 600 m long by 350 m wide by 100 m deep lens of massive sulfide, covered by 10 m to 20 m of glacial overburden, and separated from the underlying country rock quartz-plagioclase-biotite gneiss by a breccia of gneissic fragments in troctolite known as the Basal Breccia Sequence. To the west of the Ovoid lies the "Western Extension", comprising disseminated and massive sulfides in a north-dipping sheet of troctolite which ranges from upper unmineralized troctolite down through troctolite with increasing amounts of sulfide (up to 50%), to massive sulfide (in some places only), and then to Basal Breccia Sequence. East of the Ovoid, the troctolite sheet broadens out into a troctolite intrusion, within which occurs the "Eastern Deeps", a zone of massive and disseminated sulfide up to 100 m thick that is currently being explored. The mineralization of the Eastern Deeps lies along the line of intersection of a feeder sheet with the base of the intrusion. The current interpretation is that the three geological environments represent different erosional levels through a single mineralized intrusion. In this model, the deepest erosional level lies to the west and exposes the feeder to surface, whereas the Ovoid represents the base of the intrusion at surface, and the Eastern Deeps the base of the intrusion overlain by 600 m to 900 m of troctolite. Sulfides and gneissic fragments were brought up by magma flowing quickly through the feeder, and settled out where the flow rate decreased as the sulfide-bearing magma mixed with magma already emplaced in the intrusive body."

Jan 1, 1996

By Ainul Akhtar, Steve Cockcroft, Jixiang Xu, Daan Maijer, Lu Yao

"Nitrogen rich Ti-N inclusions are one of the more difficult inclusions to remove during liquid metal refining of titanium. If present in the final component, they can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading. Understanding the kinetics of dissolution of Ti-N particles during consolidation/melting of titanium can help us better operate and design the melting processes to minimize their occurrence in Premium Quality Titanium production. A numerical model based on finite difference method has been developed to calculate the dissolution of a spherical Ti-N particles in molten titanium. Analytical solutions were used to verify the finite difference code for calculation of concentration profile and the dissolution of spherical solids. Taking into account the limitations in these approaches for the different cases examined, the invariant field approximation showed good agreement with the results from the numerical analysis. Evolution of the size of a spherical Ti-N particle during dissolution was predicted by the numerical model and the particle dissolves in 163 s.INTRODUCTION Properties like low density, high specific strength and excellent corrosion resistance make titanium attractive for a variety of applications. Key characteristics in the processing of titanium and its alloys include its high sensitivity to impurities, especially atmospheric oxygen and nitrogen and its high reactivity in the molten state. Nitrogen rich inclusions Ti-N, also known as Type ? or hard alpha defects, usually have substantially higher hardness and lower ductility than the surrounding material. Because they can act as fatigue initiation sites, Ti-N inclusions can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading, even in minor amounts (tenth of a percent) (Lampman, 1990; Moiseyev, 2005; Lütjering & Williams, 2007). Ti-N encompasses as a broad range of nitrogen contents from a few wt% up to stoichiometric TiN. The liquidus temperature of Ti-N titanium increases substantially with increasing nitrogen content. Consequently, depending on the concentration of nitrogen, the melting point of Ti-N inclusions can be above bulk liquid metal temperatures during melt processing. Thus, removal of Ti-N defects hinges on dissolution and not melting."

Jan 1, 2017

By D. Shen, J. Cheung

Variable reactance arc control by the SPLC (Smart Predictive Line Controller) has been installed at many different mining sites and steel processing plants around the world. Since its first installation 18 years ago, many advances have been made to both the technology, and to its integration with furnace processes and plant operations. The SPLC has helped to improve electric arc furnace stability by reducing electrode movement while maintaining flat line arc power. Stable furnace operation at higher average power increases productivity. This paper summarizes the progression of electro-technology at Hatch since the 1970s, including fixed and variable reactance, digital electrode regulation, and fast variable speed hydraulics for Soderberg electrode, as demonstrated and benchmarked through projects and lessons learned over the years.

Jan 1, 2015

By Nancy E. Wilk

In 2015, more than 1.2 million deaths annually were estimated to be caused by occupational risks (WHO, 2018). In 2021, this estimate increased with the publishing of the World Health Organization (WHO) and the International Labour Office (ILO) Joint Estimates of the Work-related Burden of Disease and Injury based on data from 2000 to 2016 (WHO/ILO, 2021). These global estimates reported that each year 1.9 million people die from exposure to occupational risk factors, 81% of these fatalities resulting from non-communicable, occupational diseases. WHO/ILO notes that the health-related risk factors with the largest number of attributable deaths were exposures to long working hours followed by workplace exposures to particulate matter, gases, and fumes. The health outcome with the greatest work-related burden of deaths was chronic obstructive pulmonary disease, followed by stroke and ischaemic heart disease. In considering the 2021 data published by WHO/ILO, it is likely that the estimates are low and underestimate the true burden of occupational disease and injury. In support of that position, more recently the ILO estimated that “2.3 million women and men around the world succumb to work-related accidents or diseases every year; this corresponds to over 6000 deaths every single day” (ILO, 2022).

Jan 1, 2023

By G. Azimi, C. A. Ang, F. Zhang

"Nickel recovery from laterite ores generates large amounts of solid and liquid wastes. This is primarily due to the low concentration of Ni (about 1.4 wt%) in the feed ore to the High-Pressure-Acid-Leaching (HPAL) process. It is known that the HPAL residue contains a high concentration of hematite, a commercially important source of iron in the steelmaking industry. However, the balance is natroalunite, containing sulfur, which is a detrimental element in the steelmaking process. Hence, to make the HPAL residue a suitable feed for steelmaking, natroalunite must be removed. The current work is focused on: 1) a thorough characterization of the HPAL residue obtained from Vale, and 2) a systematic investigation of an alkaline leach process to remove natroalunite. The characterization results indicated that there are about 83 and 12 wt% hematite and natroalunite in the HPAL residue, respectively. The leaching results indicate that sodium hydroxide is the best leaching agent, which results in 55 wt% reduction in the sulfur content. The results of this work enable the conversion of an otherwise waste product into a useful feedstock for steelmaking. Furthermore, this project could potentially have significant environmental benefits by reducing the amount of residue produced during the HPAL process.INTRODUCTION Conventionally, crude steel has been obtained by reducing iron ore containing oxides such as hematite (Fe2O3), magnetite (Fe3O4), and wüstite (FeO) in a blast furnace with coke. The product is then refined in a basic oxygen furnace to produce steel with useful properties (McGannon, 1969; Turkdogan, 1978). Steel has been sought for its desirable properties and its application is widespread throughout modern civilizations. Surpassing the growth rate of other materials, the annual demand of steel has increased at a compound growth rate of 5% over the last 20 years (Baddoo, 2008). The global demand for steel was reported to be 1501 Mt in 2016 and demand is expected to double by 2050 (Cullen, Allwood, & Bambach, 2012; World Steel Association, 2016). In recent years, to meet the rapid growth of demand, secondary resources for iron have been identified as strategic sources of iron (Das, Kumar, & Ramachandrarao, 2000; Li, Sun, Bai, & Li, 2010; Matschullat et al., 2000). The residue produced from high-pressure acid leaching (HPAL) of laterite ore has been identified as one of the important secondary sources of iron (McDonald & Whittington, 2008). Laterite ore represents 60% of the world’s nickel resources and accounts for approximately 40-50% of the world annual nickel production (U.S. Geological Survey, 2016). Therefore, the amount of iron residue produced by the process is substantial and its utilization will produce both economic and environmental benefits."

Jan 1, 2017

By Leslie Gertsch

Outline First progress report ? ?Introduction ?Non-terrestrial mining ?Near-term targets ?Stages of mining ?Study procedure Capabilities needed for non-terrestrial mining ?Mining methods ?Mining unit operations ?Typical surface mine operations sequence ?Results to date General effects of gravity ?On fragmentation ?On excavation ?On transport ?Conclusions / Recommendations

May 1, 2013

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By R. C. A. Thurston

Introduction A mechanical spring has been .defined by Wahl ( 1) as 'an elastic body whose ?primary function is? to deflect or distort under load, and which recovers its original shape when released after being distorted'. Most material bodies are elastic to some extent ? and will deform under load, but they are seldom regarded as springs since this is not their primary function. The principal applications of springs are the absorption of energy and the mitigation of shock, the support cf moving masses or the isolation of vibration, and the provision or measurement of definite loads or torques. A large number of spring types have been developed to serve these purposes and to meet the different operational requirements; they range from the large semi-elliptic leaf suspension spring to the delicate watch hairspring. The springs of most importance in machine design, however, are the helical round-wire compression or tension types. They are made in a wide variety of sizes and are used in tremendous quantities, mainly because of their low cost, their compactness, and their relatively high efficiency. Their field of application is as broad as that of machine design itself, but the bulk of production is almost certainly for suspension systems of vehicles such as automobiles, freight and passenger cars, and mine cars, and it is with the last of these applications that this paper is primarily concerned.

Jan 1, 1951

By Geo. E. Cole

A GREAT deal of time and energy is now being devoted to the study of post-war reconstruction and rehabilitation, in spite of the fact that as yet we have not won the war in which we are presently engaged. If you feel that the study of post-war problems takes our thought away from the problem immediately before us, you may well query, "Well! What has all that to do with winning the war, our most urgent problem today?" The answer has been given by Principal James of McGill University, Chairman of the Cabinet Committee on Reconstruction: "Reconstruction is something which must be thought of in advance, partly for the purpose of recognizing exactly the influence of war-time activities, controls, and regulations on the post-war Canadian scene. Many people are acutely interested in this great problem. It is not that they are not interested in the war itself, or epochal events that are taking place from day to day. They have a vision of that future which they hope will be Canada's, and this vision inspires them to even greater efforts at the present time". The trend of events would indicate that changes, economic and industrial, after this war will be greatly out of line with those that followed previous wars in history, for the present struggle has involved every nation in the world. In the peace that will come, every engineer will have a task in bringing the most desirable order out of the most distressing chaos. We certainly are living in a changing world; we are witnessing geo-graphical and economic readjustments that no other generation in world's history has ever witnessed. And there is an opinion gaining strength in our Dominion, as in other lands, that after this war we shall live in a world in which our process of thinking and our very way of life will have to undergo drastic changes to cope with the new order of things. Sadly our world of today has had to revise the sublime vision that nation shall not lift up sword against nation, while salvage operations continue to beat ploughshares into tanks and the peaceful pruning-hook into a weapon for the deviltry of the commando.

Jan 1, 1943

By H. T. Michels

Recent laboratory studies show that several bacteria, known to be human pathogens, die when they come in contact with copper and copper alloy surfaces. The amount of live bacteria drops by several orders of magnitude, to zero, on copper alloys in a few hours. In contrast, no reduction is seen in the concentration of live organisms on stainless steel during the six-hour test period. Aluminum painted and coated surfaces and plastics would show behavior similar to stainless steel and show no effect. Coatings and other surfaces claiming to be antimicrobial showed little to no effect. These results suggest the selection of copper alloys for surfaces exposed to human touch can materially assist in reducing the transmission of infectious organisms. In order to make antimicrobial claims in the United States, the approval of the US Environmental Protection Agency (EPA) is required. The EPA-required efficacy testing is described and the test results are summarized. It is anticipated, that once regulatory approval is obtained, that this will facilitate the introduction of antimicrobial copper alloys in hospitals, nursing homes and other healthcare facilities, as well as schools, and public buildings. Some of the application and barriers, to entry into the healthcare markets are mentioned.

Jan 1, 2007

By Robert S. Penczak

Red Lake Gold Deposits ? Descriptive Classification (modified from Pirie, 1982) VHR Au -- Volcanic-hosted (vein & wall-rock) replacement Au deposits ~93% of camp production Q-(T) Au -- Quartz-(tourmaline) vein Au deposits ~7% of camp production Quartz-sulphide Au deposits Porphyry-hosted sulphide Au deposits Current & Significant Past Producers Camp Production 21.6 M oz / 672 tonnes Au Other Deposits / Occurrences (Intermittent Exploration

Apr 1, 2005

By Abhilash

Uranium is conventionally extracted using a process that employs strong acid (H2SO4) and an oxidant (MnO2) as leaching agents. This method often creates environmental problems, requires large amounts of energy, and involves a complex operational plant. It is not, however, economically attractive to extract uranium from low-grade ores by chemical leaching. Because the content of U3O8 in the Indian ore is usually below 0.1% by weight, it is necessary to develop an alternative process to enable the efficient and economic recovery of uranium. Uranium ore from the Narwapahar mines, UCIL is a type of vein deposit found in India, which accounts for ~54% in India. The ore (0.047% U3O8), though of Singhbhum area, possess exceptionally different mineralogy due to presence of some refractory minerals and richness of apatite (5%) resulting in a maximum 78% recovery through conventional processing at UCIL, with a very high consumption of sulfuric acid and pyrolusite, besides possible loss of uranium as uranium phosphate. To avoid usage of environmentally non-benign oxidants, remediation of influence of phosphates, and improve the overall process output of uranium; an alternate extraction technology using microbial isolate(s) is worthwhile exploring and the same is presented in the paper. The microbial isolate enriched with Acidithiobacillus ferrooxidans grown from source mine water was employed for bio-leaching of uranium while varying pH, pulp density (PD), particle size, etc. On varying pH at 35oC using 20%(w/v) PD and <75µm particle size, 83.5% and 78% uranium bio-recovery were observed at 1.7 and 2.0 pH in 40 days against maximum recovery of 46% and 41% metal in control experiments respectively. Whereas, it was observed that grinding of ore to finer size actually helped dissolution of uranium. Finer size particles (<45µm) gave a maximum biorecovery of 93% in 40days at 10%(w/v) PD, 1.7 pH and 35oC. The bio-recovery of uranium fell down from 93% to 82.73% and 60% on increasing the pulp density from 10% to 20% and 30% respectively for particles of <45µm size. The higher uranium dissolution during bioleaching at 1.7pH can be correlated with increase in redox potential from 433 mV to 664mV in 40 days.

Aug 1, 2010

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors&apos; thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda&apos;s diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By P. Groleau, O. Tavchandjian, D. Marcotte

In open pit mining, each small mining unit (SMU) is selected for mill processing based on an estimate of its true grade. The estimation is usually done using analyses of cuttings from blast holes within that SMU. One common estimator used for selection is the arithmetic average of within-SMU samples. This estimator is conditionally biased. The effect of a conditional bias is to overestimate the profit really recovered from the deposit. For this reason, a conditionally unbiased estimator is preferable. Increasing the number of samples generally improves the accuracy of the estimation (and diminishes the conditional bias, if present, of most estimators). However, there exists a practical limit where an additional sample does not improve the estimation sufficiently to cover the expense of making the analysis. This limit is specific to each deposit and depends on geostatistical parameters, economic factors, and mining parameters. This study examines how the number of samples affects the recovered reserves and the resulting profit. Also, the effects on optimal profit of varying the different factors are examined. Globally, the number of samples required increases with the selectivity of the operation. For a given ore deposit, the greater the number of SMUs selected for processing, the fewer samples are required and vice-versa.

Jan 1, 1998

By E A. Mitchell

In the fall of 1961, Cominco dis-carded its long-established system of feeding the lead blast furnaces by narrow-gauge tram and V-cars, and installed an elevated monorail bucket system. This system automatically loads buckets of sinter, along with the correct proportion of coke, and delivers them to any of several designated furnaces. Direct labour usage has been reduced by nine men per day; improved coke proportioning has been achieved; and a major safety hazard has been eliminated. Introduction I N THE fall months of l 961. the system of feeding the lead blast furnaces at the Trail, B.C., smelter of The Consolidated Mining and Smelting Company of Canada Limited was altered from the tradition-al narrow-gauge railway and V-car method to one employing mono-rail carriers. The change was in keeping with a recent trend at Trail to replace narrow-gauge tramming with alternative methods of materials handling. In the case of the blast furnace feeding, the

Jan 1, 1963