Search Documents

By W. S. Hegler

Introduction The San Antonio mine is on the north shore of Rice lake, thirty miles east of lake Winnipeg and 120 miles northeast of the city of Winnipeg. Since production was started in 1932, about 2,000,000 tons of ore have been mined. Currently in progress is an extensive development programme which involves 11,500 feet of crosscuts, 3,800 feet of raises, 1,753 feet of shaft sinking, and 160,000 cubic feet of slashing, all in footwall waste rock. It is the purpose of this .paper to indicate the necessity for this work and to describe the methods employed to carry it out. Where unknown factors are as prevalent as they are in the average Canadian gold mine, a definite answer cannot be given as to what is the most economical and efficient system for mining dipping deposits. At San Antonio, the host rock for the orebodies, locally termed basalt, occurs as a sill some hundreds of feet in width and dipping at approximately 45 degrees from surface to an unknown depth. It may be assumed that it continues well below the lowest depth established to date by diamond drilling. At present, a vertical winze (No. 3 winze) hoists the ore from the 2,360-foot level to the 1,600-foot level, on which it is hauled about 900 feet to No. 3 shaft, also vertical, and there hoisted to the mill bins on surface. To maintain ore reserves at a five-year figure, at full production, additional deep exploration was required immediately. It was decided to sink No. 4 winze, a vertical opening of the same size as the other operating shafts, to provide ten additional levels (17 to 26) at 150-foot intervals, with additional depth to allow for an underground crusher installation and usual loading-pocket facilities for three-ton skip-hoisting. The winze was bottomed at 1,753 feet below the collar, at a depth of 4,117 feet below surface, and is the deepest man-sized opening in Manitoba.

Jan 1, 1949

By J. E. Ryan

General Description Due to the extreme cold weather experienced in Flin Flon during the winter months, thought and precaution were necessary in the design of the plant buildings. The machine shop, carpenter shop, drill shop, and coal plant buildings are similar in the building materials used in their construction. They are sided with two-inch shiplap, insulated with celotex and asbestos paper, and covered with corrugated iron on all side-walls. Roofing consists of 2 by 4 lumber on edge, laminated, and further covered by celotex and three-ply roofing. These buildings are heated by means of unit heaters. The heaters are primarily steam-heated radiators, through which the air of the buildings is circulated by electrically-driven fans. Our machine shop is located to the east of, but central to, the main operating buildings of the mine and plant, and is so connected by a net work of tracks as to be able to serve all portions of the entire plant conveniently. The building is divided into two bays, the main bay 53 ft. by 340 ft., and the east bay 24 ft. by 340 ft. The shop office and drafting room, a two-story annex 24 ft. by 30 ft., is located on the west side of the shop. The arrangement within the shop is such as to house conveniently the several departments, namely, heavy machine tool section, repair floor section, boiler shop heavy tool and floor section, blacksmith heavy tool and forge section, tool room, electric welding rooms, stock room, tin and copper shop, and electrical parts and armature winding and repair shop (see Figure 1). All the heavy tools, the repair floor section, and railway tracks are so located in the large open bay as to be fully serviced by an electrically operated 15-ton bridge crane, with a span of 50 feet and a travel the full length of the shop. A standard-gauge railway track, branched off the main line, penetrates the full depth of the building. This track lies along the extreme east side of the main bay, allowing easy entrance and movement of rolling stock and heavy machinery, loaded on standard flat-cars, to the repair floors in the main bay. Eight jib cranes, affixed to building columns, further facilitate the heavy repair work throughout the various shop divisions. Our light and heavy machine tools are standard equipment, not unlike tools used in mine, mill, and railway shops.

Jan 1, 1935

By J. D. T. Steyl

Anglo American Corporation and the University of British Columbia have developed a medium-temperature oxygen pressure leaching process for the extraction of copper from chalcopyrite concentrates in an acid-sulphate system (AAC/UBC process). Leaching is performed at 150°C and surfactants are added to disperse molten elemental sulphur from the unreacted sulphide surface to prevent liquid sulphur occlusion. Copper extractions of over 95% and elemental sulphur yields of around 60% were observed over a 2-hour average residence time in a continuous pilot autoclave. Sporadic blockages occurring under continuous conditions were found to be caused by the accumulation of molten elemental sulphur mixed with unreacted sulphide mineral. A batch programme of experimentation was undertaken to establish the reason for this phenomenon. Batch experiments were conducted at low pulp densities on concentrate samples with narrow size distributions and at similar solution compositions to those experienced in the pilot autoclave. The overall rate of chalcopyrite oxidation was shown, under approximately constant solution composition, to be a strong function of the total available mineral surface area. Initial copper extraction rates followed the shrinking particle kinetic model under intrinsic surface control. Deviation from shrinking particle kinetics was however observed after a certain oxidation time. Secondary electron images identified small (typically less than 20 µm) sulphur conglomerates at the point of deviation, which 'collected' unreacted chalcopyrite mineral particles and lowered the total mineral surface area available for oxidation. These sulphur clusters are thought to be the precursor for blockages experienced in the continuous pilot autoclave. These results emphasised the importance of fine grinding (P80 5-20 µm) and suggest that shorter residence times may minimise the formation of sulphur conglomerates in a continuous autoclave operating at medium temperature.

Jan 1, 2004

By H P. Tardif

This paper briefly describes some of the phenomena encountered when materials are submitted to extremely high pressures, such as those produced by the detonation of an explosive charge placed in contact with the material. It was found that extensive changes take place in the? microstructure of iron and steel. Diffusion-controlled processes, such as the transformation of lamellar pearlite, the recrystallization and grain growth of ferrite, and the homogenization of the pearlite-ferrite structure, can take place within micro-or milliseconds. Mechanical twins can propagate without deviation from ferrite to pearlite, thus indicating a proeutectoid ferrite-pearlite-ferrite orientation relationship. The propagation and interaction of intense stress waves in materials was demonstrated with the use of Armco iron. Finally, a comparison is made of the damage produced in metals by the formation of craters made by explosive shock and by hypervelocity impact. D DRING the last few years, exceptional development has taken place in the field of explosive metallurgy, i.e., the

Jan 1, 1964

By Leonard Kellogg

Introduction The Mine Manager or Superintendent is a man faced with a difficult problem. He must direct the activities of his mine in such a manner that, over a period of time, the greatest possible profit will be realized. In this respect, a mine is no different from any other business organized for profit. What makes the mine manager's task so difficult then? The profit of a mine is determined by -among other things -the grade of ore, the market price of the metal or metals produced, and the cost to operate the mine. The mine manager cannot do much about the first two of these, but he has considerable control over the operating cost. This cost will depend in large measure on the nature of the programme on which he plans to operate his mine. This operating plan may be broad or specific, on a long-range basis or on a month to month basis. The development of the plan, however, is made very difficult by the existence of so many factors which must be considered. These may be (1) factors requiring decisions based on the best judgment and interpretation of engineering and geological information available, or (2) items which must be considered but which are largely non-controllable. To be more specific, examples of such items would be: (1).-(a) The amount and type of development work to be done in relation to amount of ore to be mined. (b) Mining methods to be followed and type of equipment to be used. © Amount of exploration diamond drilling to be done if the orebody is not clearly defined. (2).-(a) Rock type and degree of hardness. (b) Width, depth, and pitch of veins. © Amount of work requiring timbering. (d) Faults encountered. (e) Water and gas conditions met with.

Jan 1, 1952

By Jean-Marc Lulin

"Depuis 1906, pres de 130 gisements ont ere decouverts dans la inture archeenne polymetallique (Cu, Zn, Au, Ag) du nord-ouest becois. Une etude regionale du developpement du potentiel inier est presentee puis detaillee pour quatre secteurs: RouynDranda, Val d'Or-Malartic, Bousquet-Cadillac et Matagami.L' analyse est conduite a l' aide des parametres suivants: temps, ethodes de decouverte, profondeur des gisements et poids metal. ~~ courbes cumulatives illustrant le nombre de gisements decouverts fonction du temps montrent une forme generale en ""S"" dont les i'iations de pentes correspondent aux variations dans les taux de ~ouverte. Initiation, realisation et stabilisation des cycles de decourte sont ainsi mis en evidence. Deux ""bourns miniers"", de 1922 a ~5 et de 1955 a 1965, rassemblent 72 % des mines identijiees squ' a present.La plupart des mines sont trouvees en subsurface: 90% ont leur fmet entre 0 et 100 metres de profondeur dont 70 % entre 0 et 10 etres. Dans le temps, il y ad' abord recolte par prospection puis par fphysique et enjin, developpement progressif du potentiel en proeur avec des methodes composites. Environ 80% du poids metal extrait de 4 camps miniers, couvrant 8% de Ia surface regionale quelques gros gisements dominent /a production.Ces donnees permettent de proposer une nouvelle approche pour lysed' une region miniere:La distribution de Ia profondeur des gisements en fonction du temps est indicatricede /amaturite d' uncampminieret peut servir a evaluer son potentiel residue/.L' analyse des courbes en ""S"" permet d' extrapoler les taux de succes relies aux differentes methodes et met en relief le role crucial de I' innovation dans I' exploration.ABSTRACTSince 1906, some 130 deposits have been discovered in the Archean polymetallic belt of northwestern Quebec. In this paper, the development of the mining potential is analyzed at the regional scale and for the following mining camps: Rouyn-Noranda, Val d'OrMalartic, Bousquet-Cadillac and Matagami.The analysis is based on the following parameters: time, discovery method, depth and weight of metal extracted. Curves showing the cumulative number of deposits discovered as a function of time are ""S"" shaped with slope variations corresponding to changing discovery rates. Initiation, realization and stabilization of discovery cycles are thus well represented. Two ""mining booms"", 1922 to 1945 and 1955 to 1965, account for 72% of the mines identified to date.Most exploitable orebodies have been found near the surface: 90 %have their top between 0 and 100 meters, including 70% between 0 and 10 meters. Early discoveries were made by prospecting, followed by geophysics while the progressive development of the depth potential is being realized by a combination of methods. Approximately 80 %of the metal extracted comes from four mining camps which cover 8% of the area, but most of the production can be allributed to only a few large deposits. Based on these data, a new approach to the analysis of a mining region is proposed:1) The distribution showing deposit depth versus time is indicative of the maturity of a mining camp and can serve to evaluate its remaining potential.2) The ""S"" curve analysis can be used to extrapolate the success rate of a specific exploration method and also stresses the crucial role of innovation in exploration."

Jan 1, 1990

By Jean-Marc Lulin

"Depuis 1906, près de 130 gisements ont été découverts dans la inture archéenne polymétallique (Cu, Zn, Au, Ag) du nord-ouest québécois. Une étude régionale du développement du potentiel inier est présentée puis détaillée pour quatre secteurs: Rouyn-Dranda, Val d'Or-Malartic, Bousquet-Cadillac et Matagami.L' analyse est conduite a l' aide des paramètres suivants: temps, méthodes de découverte, profondeur des gisements et poids métal. Les courbes cumulatives illustrant le nombre de gisements découverts fonction du temps montrent une forme générale en ""S"" dont les i'iations de pentes correspondent aux variations dans les taux de couverte. Initiation, réalisation et stabilisation des cycles de décourté sont ainsi mis en évidence. Deux ""bourns miniers"", de 1922 à 1945 et de 1955 à 1965, rassemblent 72 % des mines identifiées sqú à présent.La plupart des mines sont trouvées en subsurface: 90% ont leur mmet entre 0 et 100 mètres de profondeur dont 70 % entre 0 et 10 êtres. Dans le temps, il y a d' abord récolte par prospection puis par ophysique et enfin, développement progressif du potentiel en proeur avec des méthodes composites. Environ 80% du poids métal extrait de 4 camps miniers, couvrant 8% de Ia surface régionale quelques gros gisements dominent /a production.Ces données permettent de proposer une nouvelle approche pour analyse d' une région minière:La distribution de Ia profondeur des gisements en fonction du temps est indicatrice de la maturité d' un camp minier et peut servir a évaluer son potentiel résiduel.L’analyse des courbes en ""S"" permet d’extrapoler les taux de succès relies aux différentes méthodes et met en relief le rôle crucial de I' innovation dans I' exploration.ABSTRACTSince 1906, some 130 deposits have been discovered in the Archean polymetallic belt of northwestern Quebec. In this paper, the development of the mining potential is analyzed at the regional scale and for the following mining camps: Rouyn-Noranda, Val d'OrMalartic, Bousquet-Cadillac and Matagami.The analysis is based on the following parameters: time, discovery method, depth and weight of metal extracted. Curves showing the cumulative number of deposits discovered as a function of time are ""S"" shaped with slope variations corresponding to changing discovery rates. Initiation, realization and stabilization of discovery cycles are thus well represented. Two ""mining booms"", 1922 to 1945 and 1955 to 1965, account for 72% of the mines identified to date.Most exploitable orebodies have been found near the surface: 90 %have their top between 0 and 100 meters, including 70% between 0 and 10 meters. Early discoveries were made by prospecting, followed by geophysics while the progressive development of the depth potential is being realized by a combination of methods. Approximately 80 %of the metal extracted comes from four mining camps which cover 8% of the area, but most of the production can be allributed to only a few large deposits. Based on these data, a new approach to the analysis of a mining region is proposed:1) The distribution showing deposit depth versus time is indicative of the maturity of a mining camp and can serve to evaluate its remaining potential.2) The ""S"" curve analysis can be used to extrapolate the success rate of a specific exploration method and also stresses the crucial role of innovation in exploration."

Jan 1, 1989

By D. DeGagne, E. De Souza, J. F. Archibald

This paper describes the potential use of anew agent material for backfill consolidation, ground waste glass, to be used as partial replacement of Portland cement fractions within backfill. Significant fractions of commercial and residential silica glass production is currently utilized as waste landfill and must be disposed of at high cost and with no foreseeable environ-mental benefit. This paper also demonstrates that waste glass materials could be effectively recycled as backfill additives, and that a significant, large and stable source of additive supply, currently land filled, can be developed. This new application will generate added value for such materials, serve to promote positive environ-mental stewardship and satisfy engineering sup-port requirements in mines.

Jan 1, 1997

"9.1. IntroductionThe application of the electron microprobe for in-situ analysis of platinum-group minerals (PGM), first reported by Borovskii et at. (1959) and Genkin (1959), has resulted in a large and growing number of analyses of unidentified PGM. Figure 9.1 charts the increase in the number of reported unnamed PGM from 3 in 1959 to a total of 140 by 1979. All these minerals, with the exception of UN1968-5 and UN1976-1, were analyzed with the electron microprobe.There has been no recognised or consistent manner for reporting these unidentified PGM. The term ""unnamed"" has been used for PGM that are considered to be new species without a name as well as for PGM which have not been exhaustively compared to named and unnamed PGM in order to determine whether they are unique. Many of the so-called unnamed PGM are only unnamed because of poor microprobe analyses or because larger than usual elemental substitutions (e.g. Bi for As) made it difficult to calculate the true stoichiometry. Some of these unnamed minerals have been unnecessarily reported with non-stoichiometric formulae, as discussed by Cabri (1980). Better analytical data should reduce the number of such proposals.Another unfortunate practice, possibly used to by-pass the scrutiny of the Commission for New Minerals and Mineral Names, I.M.A., is to report a ""new"" mineral by referring to it by a name made up of its constituent elements. This has been deplored on a number of occasions (cf. discussion in Fleischer et at., 1976, p. 179), but some journals continue to publish such material. The Commission on New Minerals and Mineral Names has not recognised such ""names"" and these PGM are therefore included in this chapter with other unnamed minerals.A further example of inconsistency in reporting unnamed minerals is the report of a specific ideal stoichiometry with no further details (not even an analysis!); sometimes with a note that this will be reported in greater detail in due course. I have also been guilty of similar optimistic statements and, unfortunately, it is not always possible to follow through. Some authors give data on unnamed minerals in such a discrete manner that their reports are sometimes missed in literature searches."

Jan 1, 1979

By A. Ignatieff

"Demonstrations of Automatic Coal Burning EquipmentAT THE 1951 and 1952 Annual Coal Research Conferences sponsored by the Dominion Coal Board and attended by delegates from the Dominion and Provincial governments as well as industry, the importance ,of encouraging the co-operative interest of Canadian coal and equipment industries in •promoting the use of equipment types best suited to burn given Canadian coals was emphasized. It. was suggested that this idea •be enlarged upon at forthcoming C.I.M. meetings that would be .attended largely by coal mining engineers.With this in view, a Domestic Heating Forum (1) was featured in the Coal Division programme at the 1951 Annual Western Meeting of the Institute in Calgary, and a much more ambitious programme, highlighted by live demonstrations, was •staged at the combined Annual Western Meeting and Fourth Meeting of District 4 held in Winnipeg in October 1952.With the excellent co-operation of a number of equipment manufacturers and coal companies, and with facilities kindly provided •by the University •of Manitoba authorities, burning demonstrations were• arranged in the Agricultural Engineering Building, on October l 7th. These demonstrations were a fitting sequel to the Coal Division sessions held in the Royal Alexandra Hotel on October 16th, at which the combustion of coal was specially featured in a series of papers by prominent Canadian and United States specialists.The primary purpose of the demonstrations was to •show that all coal, regardless •of rank, can be satisfactorily used provided that proper application is made with equipment suited to its purpose."

Jan 1, 1953

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, R. Tichy, W. Ecker, M. J. Mikl-Resch, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (Figure 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (Figure 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, M. Mikl-Resch, R. Tichy, W. Ecker, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (fig. 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (fig. 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By The Staff

WE were requested to make a digest of our original grinding report, Fine Grinding Investigations at Lake Shore Mines. This digest is much easier to read than the original report, but it lacks the experimental 'evidence' found in the first report which, in many cases, is much more interesting and educational than the conclusions derived from it. In the course of rewriting the paper, we noticed several new angles on the test data which had not occurred to us previously. From the data included in the report and other tests not published, calculations were made which indicated a line of new test work. These tests, among other things, more than suggest a technique for designing the length of mills, the position and number of classifiers, and the total loads a mill should carry.

Jan 1, 1941

By J. Y. Murdoch

TAXATION has become a major item in the operation of Canadian mines, and, as such, merits our most serious consideration. I feel it was a splendid idea for the Institute to set aside this time for a frank discussion of this important subject, and believe great benefit will result from a better understanding of the methods and underlying principles involved. Mining, as a great national industry, may quite properly be called upon to pay its fair share of the cost of running the country; and there is no tendency on our part to avoid this responsibility. There is, however, a very definite demand that the proportion be just, and fairly and sensibly applied. I believe that Mr. C. G. Williams, Secretary of the Canadian Metal Mining Association, and others, are giving details of the various Provincial and Dominion regulati6ns, so I shall not touch on that phase of the situation. However, there are some important factors to which I should like very briefly to call your attention. The first is the vital need for stability. As you all know, a considerable period must elapse between the preliminary stages of any mining venture and the time when it comes to production-or is finally abandoned as un-profitable. These early days are fraught with many unavoidable uncertainties. If, to these natural hazards, the apprehension of instability of governmental action be added, the risk becomes so great that capital seeks other and safer fields for investment, and many otherwise promising projects are thus discarded. There probably never has been a time in recent years when so much money was seeking investment as now. Under favourable conditions, the development of our great mineral resources would be a natural and attractive outlet for this money. The amount of taxation which the mining industry can properly absorb is of the utmost importance at this time, and it might be well to consider this question in its relation to the economic stability of our country, for it cannot be too greatly emphasized that direct taxation is only one item in the net return which our governments derive from the mining industry. Indeed, the many indirect benefits are so manifest that it would seem almost unnecessary to enumerate them! We almost invariably think of mine taxation as a direct company tax-overlooking the fact that sales tax, customs duties, acreage tax, income tax on mine dividends, foreign shareholders' dividend tax, and others, must all be taken into consideration. It would seem that the economic value of non-ferrous metal mining in Canada is not sufficiently understood and appreciated.

Jan 1, 1935

By N. Samman, S. N. Lau

"A series of new, grease-based, solvent free open gear lubricants were developed to meet the demanding service requirements of mining equipment. The use of these products has resulted in better performance under conditions of temperature extremes and in terms of longer component lives. They have gained widespread acceptance within the mining communities for such applications as the lubrication of mining shovels, draglines and ball mills.These products are WHMIS non-controlled and are environmentally acceptable. The benefits and advantages of using this type of product to lubricate mining equipment as well as the field evaluation and experience will be discussed."

Jan 1, 2002

By Min-Yuan Cheng

Heavy rainfall and typhoon oftentimes cause the collapse of hillslopes across mountain roads. Disastrous consequences of slope collapses necessitate the approach for predicting their occurrences. In practice, slope collapse prediction can be formulated as a deterministic classification problem with two class labels, namely ?collapse? and ?non-collapse?. Nevertheless, due to the criticality and the uncertainty of the problem, evaluating the collapse susceptibility of an area is a challenging task. This study proposes a novel Artificial Intelligence (AI) approach, named as K-Nearest Neighbor Based Bayesian Classifier (KNNBC), to deal with slope collapse assessment. In the proposed model, Bayesian inference is used as a framework to achieve probabilistic prediction of slope collapse. Meanwhile, K-Nearest Neighbor (K-NN) is employed as a density estimation technique. Equipped with probabilistic outputs, the K-NNBC is able to yield predictions with different levels of confidence and diminish misclassified cases. Experimental results point out that the proposed model is very helpful for decision-makers in slope collapse assessment and disaster prevention planning.

Aug 1, 2013

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed sur?cial mapping and sampling programs in the Separation Lake area of north-western Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of sur?cial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these sur?cial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t)values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sul?de mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from sur?cial samples was compared with that of in situ material. Gahnite from the peraluminous rare-element granite and pegmatite overlapped very well with sur?cial gahnite of Group 1. Gahnite from volcanogenic massive sul?de mineralization and Sedex-type mineralization overlapped well with sur?cial gahnite of Group 2. These results suggest that determination of gahnite composition in indi-cator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

By H. S. Price, F. N. Kissell, R. C. McCulloch, J. C. Edwards

"The methane em1ss10n from deep coalbeds which are actively mined is a serious problem facing the mining industry today. Pinpointing the source of methane and predicting the emission of this gas from these coalbeds is necessary if preventive techniques are to be effectively used to control methane emission. In general, because most coalbeds have water associated with them, the system to be studied may be either single-phase (methane gas) or two-phase (methane and water). Because coal mine geometry is complex and the fluids have variable properties as functions of pressure and methane concentration, the differential equations describing the flow of methane and water are not amenable to analytic solution, but must be solved numerically using high-speed computers. This paper presents the development of such a complex mathematical model along with some preliminary applications of the model to methane emission from one- and two-dimensional coalbeds with and without water present."

Jan 1, 1973

By H. O. Seigel, J. C. Gingerich, E. O. Köstlin

"To satisfy their continuing need to replenish or expand their ore reserves, mining companies are faced with the dilemma of arriving at a proper balance between the dual avenues of discovery through in-house exploration and of acquisition of properties that are relatively proven or are even in production. The returns from exploration activities may be spectacular, but are unpredictable. The allure of an acquisition lies in its promise of quick and risk-reduced addition to reserves. However, it is historically clear that quantum increments in shareholders’ values have arisen primarily through major exploration discoveries, rather than through major late-stage acquisitions. Late-stage acquisitions can prove highly profitable, sometimes based upon the planned use of superior mining or metallurgical technology, but more often occur as the result of unexpected windfalls. At the other extreme, they can become expensive failures through inadequate due diligence, or unforeseeable factors.Citing numerous case histories and industry statistics, it is concluded that a judicious combination of both exploration activity and the acquisition of prospects is the most advantageous strategy for adding new ore reserves. A skilled exploration staff is essential for success, be it through exploration discoveries or through opportunistic acquisitions, preferably at their early stages. In the future, it is anticipated that there will be fewer opportunities for acquisition because of reduced funding for junior exploration companies, leading to increased competition and higher costs for fewer properties, both in the advanced exploration and mining stages."

Jan 1, 2002

By R. L. Brown, E. A. Swanson

THE Buchans ore bodies are located in central Newfoundland, three miles north of Red Indian lake. The townsite of Buchans was named after a Royal Navy Captain who, while attempting to make contact with the Beothuck Indians, camped in the area in 1820. Ore was first found at Buchans by a Mic Mac Indian, Matty Mitchell, who discovered one of the three small orebodies in the bed of the Buchans river. The Anglo-Newfoundland Development Company, which holds mineral rights in the area, developed the orebody, but was forced to give up the venture because of difficulties encountered in separating the various sulphides. The American Smelting and Re-fining Company developed a flotation process which was capable of economically separating and concentrating the various sulphides, and, in 1926, they took a long-term lease on the property.

Jan 1, 1962