Search Documents

Environmental leaching methods such as the toxicity characteristic leaching procedure (TCLP) test or the ASLP test are used to assess wastes including mining and mineral processing by-products. These tests were initially designed as regulatory tests simulating conditions in a co-disposal municipal landfill waste facility and do not allow leaching performance to be predicted in site specific scenarios. Further, the assumptions underlying these tests tend to define worst-case scenario leaching conditions for by-products from the mineral industry disposed of outside a co-disposal scenario.   Recently some characterisation leaching test methods have been issued as ISO/TS standards (ISO/TS 21268-3:2007 and ISO/TS 21268-4:2007) that aim to define the leaching performance of soil type wastes and to predict the leaching performance of these wastes over long time frames. In this preliminary work these standards are trialled for by-products from the mineral industry and the quality of information that can be obtained from them compared to TCLP/ASLP tests.   Where clear comparisons were possible, the TCLP/ASLP tests were typically found to extract a similar, or often greater, amount of component than (i) tests conducted at the same pH but without the acetate buffer or (ii) for test conditions aimed at simulating long-term leaching in an eluate defined by the waste type. While further work is required, the preliminary results indicated that the tests may provide reliable long-term estimates of leaching performance of wastes in soil types of variable pH and provide a suitable basis for long-term planning for optimal waste handling, treatment or even re-use.

Jun 1, 2010

By Wright S, Jorgensen F. R A

The reaction between lead sulphate and a number of base metal sulphides (galena, sphal- erite, chalcopyrite and synthetic pyrrhotite was studied as a means of desulphurizing lead sulphate containing fumes and residues to levels acceptable as ISF feed. The reactants were mixed with 50% zinc oxide to act as a "basket" to contain the molten products of the reaction and pressed into small briquettes 20 mm in diam. Factors such as temperature, time and the composition of the atmosphere were investigated. Using the PbS/PbS04 system as an example it was shown that the reaction became rapid above 800¦C and that both sulphur dioxide and oxygen in the atmosphere were detrimental to achieving low sulphur in the product. In an inert atmosphere all the sulphides when roasted for 1 h at 1000¦C gave results corresponding to the elimination of more than 95% of the sulphur in the reactants. Leach plant residues were considered for use as the "basket" material. It was shown that the residual sulphide and sulphate components of the residues underwent similar reactions to those experienced by the pure systems.

Jan 1, 1987

By A Thompson, E Villaescusa

The Western Australian School of Mines (WASM), Kalgoorlie, has been performing dynamic testing of reinforcement systems as part of the Minerals and Energy Research Institute of Western Australia (MERIWA) Projects M349 and M349A sponsored by WASM, the Western Australian State Government and the mining industry. These projects have resulted in the construction and commissioning of the WASM Dynamic Test Facility and a program of reinforcement system testing. The primary purpose of the WASM projects is to evaluate the performance of complete reinforcement systems when subjected to an axial dynamic load. The test procedure, monitoring and associated analysis enable assessments for each component (ie the element, the internal fixing mechanism and the surface hardware) of the reinforcement system. The performance of a reinforcement system is usually defined by a static force-displacement response to axial loading. However, this static response may not be applicable to dynamic loadings associated with violent failure of rock due to overstressing as mines progress to greater depths. It was therefore appropriate that the responses of reinforcement systems subjected to dynamic loading be defined and evaluated. The key findings from the tests on a number of reinforcement systems are presented and recommendations made regarding their application for dynamic loading.

Jan 1, 2008

By White B

The domestic and commercial use of underground space dates back to Neanderthal man living in caves. There are many examples worldwide of the imaginative use of underground excavations, either left by mining or purpose-built. World living trends indicate that an increasing percentage of the population is living in and around major cities. Environmental, social and economic pressures associated with urban expansion can be partially catered for by a well-planned and integrated underground space regime. This paper addresses the types of underground development that are complementary to the economic and environmental pressures associated with urban expansion and high density cities. The paper explores the implications of mining and exploration technology and civil engineering, as well as the ancillary professional disciplines (legal, architecture and planning, sociology and education).

Jan 1, 1997

By R J. Nicholson, J M. F Clout

As part of an overall strategy to make significant new technological advances for the sustainability of the mineral processing and related process industries CSIRO Minerals has developed a new dry separation device. It represents a technology breakthrough and has the potential to radically change the way in which dry particle size classification is achieved in the minerals industry. Conventional dry separation techniques have limited applications and often suffer from low productivity, high operating costs, low separation efficiency, the need for dust control and a lack of flexibility. In the absence of efficient dry techniques, wet processing is often used. The use of wet processing either requires the introduction of water into a separation process, which causes environmental concerns through the need for water supply and tailings dams or the use of æunfriendlyÆ chemicals for dense media separations that have considerable impact on handling and disposal. Wet processing also increases operating costs due to plant instability, materials handling, thickening, filtration and product drying. The new CSIRO technology exploits a combination of natural and applied forces to achieve specific particle motions that produce size separation. In doing so, many of the traditional shortcomings of dry separation have been overcome. The CSIRO Dry Particle Size Separator is ideally suited for dry size separation applications within the size range 1 mm to 30 ¦mfor moderate moisture levels (2 per cent), have low unit throughput, produce a fixed cut size and are therefore impractical where very high unit capacity and low operating costs are required. This paper presents a review of dry separation devices together with details of the new Dry Particle Size Separator and typical results for a number of materials, including iron ore and quarry dust.

Jan 1, 2002

By V Narayanaswamy

SustainabilityÆs imperative of economic development in tandem with social advancement and environmental protection is widely accepted, but much debate remains about the practical implications for the minerals processing technologies and practices for the future. Experience in other industry sectors however suggests that sustainability can be a value-adding framework for innovation in processing technologies, business models and management systems. This position paper explores how sustainability can drive innovation in minerals processing, by reviewing pertinent ideas and experiences gained in non-minerals sectors. Sustainable innovations can generally be broadly ranked from incremental to transformative, with each category having its own typical improvement potential, timescale and technological and operational challenges. This leads to a æmud mapÆ for sustainable innovation in minerals processing with three distinct tracks: eco-efficient operations; sustainable plant design and sustainable processing. Competing models for the sustainable innovation process through either forecasting or back-casting, have in common the strong reliance on vision, perspective and competency, which in turn highlights the importance of sustainability frameworks. Such sustainability frameworks provide normative goals and option elicitation prompts to assist with the analysis of current processes and scoping of more sustainable alternatives. A comparative analysis of five prominent environmental sustainability frameworks revealed three cross cutting sustainability themes that challenge current resource processing technologies and practices. These are: fate of materials (zero dissipation of materials); compatibility of materials and processes; and materials intensity of industrial products and processes. Although the sustainability concepts presented in this paper have not been extensively road tested in the minerals processing industry, there is ample evidence that recent initiatives in the Australian resource sector illustrate the applicability of the proposed framework. It is therefore argued that more in-depth assessment of sustainable innovation concepts would be a valuable contribution to the sustainable resource processing theory and practice.

Jan 1, 2004

By D Ryan

Following a long period of increase, there has been a reduction in exploration expenditure and activity in Australia over the past two years. During the post Second World War period, exploration was largely driven by mining companies seeking resources to satisfy an increase in world demand, while increasing their asset base as a result of mineral discoveries. In general, return on investment to shareholders was not the major driving force. With the exception of gold the mining industry has been faced with a long-term fall of metal prices in real terms. As a result the net profit return on average shareholderÆs funds in the Australian minerals industry has fallen from over 20 per cent in 1990 to less than five per cent today. Mining is now competing for funds with communication and finance based industries yielding high returns on shareholder investment. Shareholders and superannuation fund managers seeking a high return on short-term investments have indirectly reduced the funds available to the mining industry. Globalisation of the mining industry is leading to the rationalisation of the Australian mining industry as witnessed by mergers and acquisitions of local companies by foreign investors. The return on capital invested in the Australian mineral exploration industry must improve if the industry is to be competitive on a worldwide basis. Failure to achieve this will result in capital flowing overseas or to other industries. Relatively short-term upswings in metal prices which are generally driven by threats to the supply base (eg strikes, mine closures, increases in country risk) often lead to increased capital raisings for exploration funding. As a consequence of the time taken to raise the capital and increase exploration activity, measured exploration activity lags the metal price increases. There are also lags between commencement of exploration and discovery and ore production. In the case of gold exploration expenditure peaked six years after the price rise of 1980 Companies persevering with exploration in the current difficult period will be rewarded because they will be able to capitalise on future metal price rises and a minimised time lag.

Jan 1, 2000

By E Haren, A Winchester

The CSA Mine has a long and varied history from initial discovery in 1871 through to the present. Lead-zinc mineralisation was mined historically near the surface. Today copper and silver are extracted from the deeper regions of the mine. The mine has passed through a number of owners over this time, each with a unique operating philosophy and understanding of the mineralisation. Cobar Management Pty Ltd re-opened the mine in 1999 and has undertaken extensive drilling programs to expand the resource and gain a better understanding of the mineralisation characteristics. Presently mineralisation has been located over a strike length of 1.2 km and to a depth of over 2.0 km with over 30 mineralised lenses from four identified ore systems. The refinement of geological and mineralisation models led to further discoveries and prompted a review and modification of resource modelling processes. Advanced statistical analyses prompted the implementation of ordinary kriging as a grade estimator. Improved stationarity from enhanced geological domaining has been supported by variography and kriging neighbourhood analysis studies. Resource models at CSA are now quantifiable in terms of mineralisation style and estimation reliability. The new techniques are assisting the definition of more mining fronts, which are creating new opportunities to increase mine output.

Jan 1, 2006

The three systems of mining in use in the Southern Coalfield of New South Wales are bord and pillar with or without subsequent extrac- tion, longwall and shortwall. Bord and pillar with extraction is regarded as the conventional system. The application of continuous miners and powered roof supports (Shortwall) to coal min- ing has, grown in recent years from something of an oddity among extraction systems to an acceptable and viable approach in certain min- ing environments. The method can be applied in a high proportion of situations where normal pillar extraction is practised with advantages over the conventional approach. These advantages extend to both safety and efficiency aspects and also include better utilization of coal reserves. It holds hope for further gain in efficiency because its simplicity of layout lends itself to achieving the goal of contin- uous haulage towards which operators are always striving.

Jan 1, 1976

THE slag from the blast furnaces having been granulated, a representative sample is taken to the sample mill. It is then dried, crushed through a 100-mesh screen, intimately mixed, and packeted for assay purposes.METHOD OF ANALYSISINSOLUBLEWeigh 1 grm. of the finely-pulverized slag into a 3t-in. casserole, moisten with a little water to prevent sticking, cover with a clock glass, and add 20 cc. of hot acid (1 HNOs, 3 HCI, 4 H2 0). Evaporate slowly to dryness on a hot plate and bake (without overheating) until all the gelatinous silica is dehydrated. Cool, add 20 cc. HCI (1-1), and boil gently for several minutes; filter into a 300-cc. beaker, cleaning out the casserole thoroughly with a rubber-tipped glass rod. Wash residue with hot distilled water and transfer it to a No. 1 porcelain crucible. Dry, ignite, cool in a desiccator and weigh as total insoluble matter. Dilute filtrate to 200 cc. and neutralize some of the excess HCI with NHa.OH. Warm, and pass H2S for 15 min. Filter and wash withhot water. Boil off H2 S, oxidize with 5 cc. HNOll , reduce bulk of the solution by evaporation. to about 100 cc., and transfer to a 250 cc. flask.SILICAFuse insoluble residue over a blast lamp in a platinum crucible with three or four times its weight of anhydrous carbonate of soda, for 10 to 15 minutes, or until decomposition is complete. Cool, and extract fusion in an 8-in. evaporating dish with HCI (1-1); rinse crucible and cover with distilled water, and evaporate to dryness over a water bath. Take up dry mass with 10 cc. strong HCI, and then.

Jan 1, 1922

By George G

The Circum-Pacific Map Project is a cooperative international effort to prepare and publish geological, geophysical and mineral resource maps of the Pacific Basin and adjacent land areas. Earth scientists representing 180 organizations from more than 40 Pacific Rim countries are participating in the work. The project is directed by a committee established 14 years ago as an activity of the non-profit Circuin-Pacific Council for Energy and Mineral Resources. Technical and cartographic support is provided by the U.S. Geological Survey. The Circum-Pacific Map Project is organized under five regional panels of experts on the geology and resources of the four quadrants of the Pacific and Antarctica. A series of five 1:10,000,000-scale regional maps and a 1:17,000,000-scale map of the entire Project area, the Pacific Basin Sheet, provide the cartographic base. Forty-eight individual sheets are planned and thirty have been published in eight different series, including base maps, geography, plate tectonics, geology, energy resources, mineral resources, tectonics and geodynamics. Additional special single-sheet thematic maps on the Pacific Basin base have been published and are planned for a total of more than 50 individual sheets.

Jan 1, 1987

Mineralisation adjacent to Herberton occurs within three main subcentres. The Her- berton Hill subcentre is characterised by the association of Sn,W the Herberton Dividing Range South subcentre by Sn, and the Herberton Dividing Range North by Cu, As. The relation- ships between the subcentres are discussed in terms of metal distribution, production, deposit types, wall rock alteration and re- lationships with granitoid intrusives. The temporal and three dimensional spatial re- lationships between the centres are uncertain.

Jan 1, 1978

Drilling has disclosed a sequence of Cainozoic sediments immediately to the west of the Ediacara mineral field containing little or no dolomitic debris in the lower and middle sections, but with gravel beds of dolomite derived from local rocks in the upper part. It is suggested that the lower and middle sequence of Cainozoic strata was deposited over the area of the Ediacara Range, and that this range was uplifted, probably as a horst block, during Quaternary times and was first exposed to subaerial erosion during the upper Pleistocene epoch.Lower Cambrian dolomites with associated stratiform lead mineralization, which formed the target of drilling on the western downthrown block of the Ediacara Fault, were eroded before deposition of Cainozoic sediments.Intense leaching of basal Cambrian dolomites around the periphery of the Ediacara Basin took place during Mesozoic and Tertiary times. This leaching process has resulted in enrichment of copper and lead mineralization in a thick marginal zone of residual clayey material overlain by dolomitic collapse breccia. These zones of leaching and enrichment were preserved under Cainozoic sediments which have subsequently been eroded. The Ediacara Fault appears to have been a major conduit for mineralizing fluids and is the main lineament of the Torrens Hinge Zone. Contemporaneous movements on this fault have controlled rates of depositionand thickness of sediments across the fault during Adelaidean and Cainozoic times. Though latest movements of this fault have been west block down, the predominant movement has been east block down with associated thickening of sediments to the east in the Adelaide Geosync1ine.

Jan 1, 1972

By Watson F. G

As an introductory paper of a series on the Melbourne (Australia) Underground Rail Loop extension to the extensive electrified suburban railway system the paper outlines the need for the Loop, legislative background, organizational establishment, engage- ment of consultants, design control, contracts, financial aspects, example of organizational flexibility and certification and transfer of the Loop to the Victorian Railways Board.

Jan 1, 1981

This paper provides a brief fundamental insight regarding the fabric media concept for liquor filtration. The subject matter will be of interest to metallurgists and engineers with professional responsibility for world class design of solid liquid separation processes and efficient lowest cost operation of existing mineral process plant. Avocet Mining commissioned the worldÆs first mineral liquor clarification process incorporating a fabric media liquor filter at their Lanut gold mine in Sulawesi, in 2004 with design consulting provided by the Australian company SLS Technology Pty Ltd. Development of the technology continues with applied research focused on selecting textile parameters to apply filtration to a wider range of particle and contaminant types, higher solids concentrations, and different process liquors. Liquor filtration with the Fabric Media technology offers an array of attractive benefits. For Avocet Mining, filtration of pregnant liquor directly from the heap leach pad has enabled removal of the sediment pond and sand filters from the traditional process flow sheet, thus providing significant cost and installation time savings. Avocet Mining has recently expressed confidence in the technology indicating selection preference of the technology for the expansion at Lanut and for a new project. The application design window for the Fabric Media concept is extremely flexible with the technology now successfully applied to many different liquor chemistries and application objectives around the world. Potential cost savings for solid liquid separation process plant, such as counter current decantation circuits, clarifier vessels and thickener tanks can be calculated from laboratory measurements or pilot plant demonstrations.

Jan 1, 2008

By R M. Tosdal

Intrusion related ore deposits are widespread in the Central Peruvian Cordillera Occidental and adjacent high-plains to the east and include porphyry Cu (-Au, Mo; eg Morococha), Cu-Zn (Pb-) skarn (eg Antamina), Pb-Zn-Ag carbonate hosted vein deposits (eg Uchucchacua), cordilleran base metal (eg Cerro de Pasco) and epithermal deposits (eg Quicay). Geochronology and petrochemistry of intrusive rocks associated with mineralisation reveals that: most ore deposits were emplaced in the late middle to early late Miocene; and are related to calc-alkaline granodioritic igneous rocks with Sm/Yb >3, Sr/Y >40 and Y/Th <1.5. The largest deposits, including Antamina, Colquijirca and Cerro de Pasco are associated with intrusions with Sm/Yb >4 and which, as indicated by Pb and Sr isotopic data, have undergone relatively moderate middle and upper crustal assimilation. The chemical signature of igneous rocks related to mineralisation likely reflects melt equilibration in the lower crust at a crustal thickness of more than 45 km. Mineralisation was favoured by a change from normal to flat subduction, resulting in increased compression, crustal thickening and subsequent cessation of the magmatic arc. Premiocene ore deposits do occur, but are restricted to a broad E-W corridor between Uchucchacua and Milpo and probably were controlled by a crustal-scale structural discontinuity across the strike of theAndes. Not all igneous rocks with high Sm/Yb and Sr/Y ratios did acquire their trace element signature in the lower crust. Petrographic and Pb isotopic evidence indicates shallow crustal hornblende fractionation or assimilation of pelitic material as possible causes for high trace element ratios in some rocks. These are apparently unrelated to polymetallic mineralisation. Thus, critical evaluation of petrographic and geochemical data in metallogenetic studies, especially in areas with complex basement architecture such as Central Peru is critical and should not be reduced to simple trace element ratios. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Queensland Mines Limited operates a small uranium treatment plant at Nabarlek in the Arnhem Land Aboriginal Reserve, some 265 km due east of Darwin. It was the wish of the local Aboriginal people that the ore be treated over an eight year period and that no township be constructed in Arnhem Land. Due to these wish- es it was decided to house employees and their families in Darwin and fly the employees to the minesite for work rosters. A singleman's style camp only was constructed at Nabarlek. To satisfy the Aboriginal people's wishes all recreation time is spent offsite thus lead- ing to a roster system whereby employees spend three distinct periods of 6, 6 and 4 days on- site, broken by recreation periods of 3, 4 and 5 days in Darwin, during each 28 day period. Employees are divided into four opposing rosters, which allows at any given time for approximately half the workforce to be onsite and the other half on rest and recreation leave in Darwin. This method of staffing has generally proved to be most satisfactory although at times problems arise, in terms of both product- ion and social effect not normally encountered when operating within more conventional circum- Stances.

Jan 1, 1984

Mine planning is difficult. Even for small operations, it involves reasoning with complex variables and the practical difficulties of mining. It is also about predicting and planning the future in an unpredictable physical and economic environment. Yet we rely on a handful of individuals and their spreadsheets to tell us how to do it û planning the business and activities of mining to hopefully produce results that will please stakeholders. Does it work? Not as well as it could. Planning affects everyone in the organisation. Company executives are demanding more reliability and stability in cost and revenue forecasts from their operations. Management want to explore ways of being more cost effective. Miners and contractors want more useful plans and realistic targets. And the planners have to describe the method that will translate business objectives into implementable plans. Even with the use of computer technology a lot of effort is expended to produce plans that are largely qualified by the level of knowledge and experience of individuals. Better use of information and the application of Intelligent Technologies can improve the quality and reliability of mine plans and schedules. By capturing the knowledge within the organisation and speeding up the planning process, Intelligent Technologies allow more options to be considered more rigorously. But it is not just about technology. It is about how technology is implemented and embodied in the way the business is managed for performance. When this happens, the real benefits of better planning start to flow.

Jan 1, 2003

By Li G, Dean-Jones G. L, She T

Highwall mining is a specialised and largely automated mining method developed in the United States for the extraction of coal left under a shallow overburden cover after cessation of economical open cut mining operations. As the name indicates, coal is extracted from the seam exposed along a highwall by a remotely controlled continuous miner operating in a single unsupported opening and brought to the surface by a string of conveyor segments. The single entries are separated by coal .pillars and driven normal to the highwall, over areas where the thickness of cover and volume of recoverable coal is insufficient to allow or justify conventional underground mining. An additional highwall mining method is augering. The success of high wall mining operations depends significantly on geological features, notably the stability of the working roof, determined by the type and mechanical properties of the immediate roof strata. Stability of the ribs, absence of floor heave, faults and dykes are further important prerequisites for profitable highwall mining. The geometric relationship between the spatial attitudes of existing joint systems, the direction (azimuth) of the single entry opening and its vertical profile determine the unimpeded depth of penetration into the coal and thus its economic success. The mechanical implications of the lithological transition zone from a coal seam to either primary or original roof strata, compared to an interface between the coal seam and overlying strata, characterised by a sharp erosional boundary between coal and a secondary immediate roof stratum, are very significant. The compatibility between the response to mining by the geological system (floor-seam-roof) and the capability of the mining equipment to prevent the development of instability are essential requirements from a mechanical viewpoint. The minimisation of vibrations, very good horizon control, an ability to vary the profile of the opening, and the maintenance of consistently high advance and retreat rates, are also important aspects of profitable highwall mining.

Jan 1, 1995

The areas of impact when employing high productivity long wall systems are reviewed and the financial implications of the most significant areas highlighted. A distinction has been made between availability and utilization. The need for more efficient delay recording, together with increasing control and utilization of the systems has been identified and the measurability of the latter discussed. The increased use of electronic delay reporting direct from the operating unit as the basis for operational control and a pre-emptive maintenance philosophy is seen as an important area of achieving higher performances from existing long wall production systems and Configurations.

Jan 1, 1988