Search Documents

By Hedge AS

Mt Whaleback is one of the largest open-cut iron ore mines in the world. Haulage cost is the single largest component of operating costs at the mine. Past studies towards alternatives to truck haulage have recognised the potential viability of an in-pit crushing and conveying system, dependent on the proportion of uphill haulage. After seventeen years of mining Mt Whaleback still contains more than 1,000 million tonnes of ore, needing 1,800 million tonnes of waste removal to extract it. What was once a quarry has now turned into a large open pit. The increasing proportion of uphill haulage, the need to replace ageing 120 ton and 200 ton trucks and the necessity of achieving and maintaining a higher stripping ratio prompted, in 1984, the initiation of a new feasibility study into the viability of alternative material handling systems. A semi-mobile in-pit crushing and conveying system was found to be most suited to Mt Whaleback conditions. The East Pit was selected as the best location based on the analysis of haulage profiles measured on long term incremental mine plans. A capacity of 22 million tonnes per year was considered achievable by the proven technology currently available. A detailed estimation of capital and operating costs of two systems - one with trucks only and another with trucks, crusher and conveyor - for the removal of 22 million tonnes per year of waste rock, showed substantial cost savings achievable by the proposed system. An economic evaluation of the two systems established the advantages of constructing the in-pit crushing and conveying system. This is now under construction and will be commissioned in early 1987. Experience gained in constructing and operating this installation is expected to influence decisions on similar installations in future.

Jan 1, 1986

Optimisation and sensitivity analysis of final pit limits is now an accepted procedure for open pit planning studies. Tools to assist the design engineer in an underground metalliferous mine to make optimal choices for the selection of major development, stope geometry and cut-off grade analysis have not been available. The engineer has had to rely on experience and a limited analysis of design alternatives. A new tool called the `floating stope' has been developed to define the optimal (boundary) limit for material that can be economically extracted by underground stoping methods. The method is analogous to the `floating cone' method of open pit optimisation. The geology and mineralisation are modelled as a regular or subcell block model. Included in the model are structural and geotechnical features, and any previously mined out areas. Inputs to the procedure include the minimum stope dimensions, cut-off grade, stope head grade, and the way in which dilution is to be calculated. The optimisation procedure can be directed to maximise ore tonnes, grade, contained metal or the economic (dollar) value of material mined. The procedure can be applied at each stage of mine evaluation and design to assist with preliminary resource appraisal, selection of stoping methods, and detailed mine design. As with open pit optimisation procedures, manual intervention by an experienced engineer is required to produce practical and detailed designs. This practical design should follow the optimised design as closely as possible. The paper outlines the algorithms used in the definition of the stope envelope, and describes the analysis and results of several case studies where the optimisation procedure has been applied.

Jan 1, 1995

The Youga gold mine in Burkina Faso, West Africa, is scheduled to produce first gold in the third quarter of calendar 2007. The project is expected to produce 540 000 oz of gold over 6.5 years, from a conventional open pit carbon in leach mine. The direct capital cost of the project is US$47 M. Etruscan Resources Inc, a Canadian based gold exploration and development company, holds 90 per cent of the project company Burkina Mining Company SA (BMC). The state of Burkina Faso is free-carried for the remaining ten per cent of BMC. RMB Resources Limited, of Melbourne Australia, has arranged a US$35 M project finance facility for BMC (the Borrower) as the majority of funding for the Youga project development. The loan facility was provided by RMB Australia Holdings and Macquarie Bank Ltd (the Lenders) each as to 50 per cent in the lending syndicate. The Lenders also provided a gold hedging facility to guarantee a minimum price for the projectÆs gold production. Burkina Faso is a francophone country, part of the Economic and Monetary Union of West Africa (UEMOA). The project financing is the first such facility to be arranged for a mining project in Burkina Faso, with little or no precedent available in other UEMOA countries. Therefore, while the Youga gold project is forecast to be a robust project applying conventional mining and processing methods, a number of legal, technical, commercial and social issues required identification, evaluation and resolution before the loan could be established. This paper describes that evaluation process and the resolution of these issues. In-house experience and expertise in both the LendersÆ and BorrowerÆs teams has facilitated a greater understanding and æownershipÆ of the issues and hence provided comfort with risks which might not normally be taken in conventional project developments and project financings. As a result, blanket external reviews were not required by the Lenders. A long-standing relationship between Etruscan and RMB Resources also facilitated solutions to a number of issues. Nevertheless, a degree of flexibility by the Lenders, the Borrower and Etruscan was required to successfully close the financing.

Jan 1, 2007

This paper deals briefly with three of the more controversial aspects of the geology of the Mount Isa ore deposits namely the geologic structures, the method of ore deposition and the origin of the ore.In the section on geologic structures, an outline is first given of the purely tectonic deformation advocated by the early authors. The current interpretation, which differs in the proposed order of events and causal forces, is then discussed. Other concepts, which attribute all or part of the deformation to sedimentary features or preconsolidation movement, are outlined ilnd commented on.The remaining two sections deal mainly with the better known lead-zinc orebodies. In the first of these a brief description and criticism is given of the early interpretation which was based on the deposition of successive waves of mineralisation which replacedindividual beds in the shales. The current ideas, which visualise emplacement of the ore between the beds rather than replacement of them, is then discussed. The final section develops the case for a sedimentary origin of the lead-zinc ores and broadly outlines the author's ideas concerning the evolution of the Mount Isa ore deposits.INTRODUCTIONAny consideration of the geology of Mount Isa must begin with the work of Blanchard and continue with that of Hall. Individually, or as co-authors, they published various papers on the geology of Mount Isa. Of these, the best known is their "Rock Deformation and Mineralisation at Mount Isa" (1941) which gave a comprehensive account of all aspects of Mount Isa geology.It is necessary to appreciate the limits set on geological knowledge of the mine and environs in 1941 by the extent of mine development and regional geologic studies. Underground, 7 level (897 ft.) was the lowest producing level. Development on 8 (1073 ft.) and 9 (1247 ft.) levels consisted only of exploratory drives and crosscuts in the vicinity of the Davidson Shaft. The tops of the 650 and 750...

Jan 1, 1961

By Kyle J. H, Misra V. N

The most recent development in gold processing is the increasing use of heap leaching for the extraction of gold from low grade ore, and old tailings dumps. The reason for this trend is mainly to do with economics. The advantage of heap leaching is the considerable saving in both capital and operating costs. However, not all ores are amenable to heap leaching. It is only applicable to well oxidized ores that have suitable permeability char- acteristics, and the gold recovery is poorer than by conventional process. In this study, an attempt has ben made to ascertain the heap leaching characteristics of Western Australian gold ores on the bench scale using multiple, appropriately sized leach columns. The influence of particle size, flow rate, column depth and leaching time on the rate of gold extraction was determined. The percolation rate of cyanide leaching solution was deter- mined with and without gypsum additions. Efforts were also made to minimise particle segregation, fines migration and solution channelling during leaching, so as to improve solution percolation, gold extraction rate and recovery.

Jan 1, 1991

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A.G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue- gases, the circulating fluid bed technique with internal oil combustion at 2.2000 F for the calcining step and 'a five-stage fluidized bed cooler for heat recovery from calcines, the process gives an outstanding heat- efficiency. In a first industrial plant for 560 sh. t. alumina per day heat consumption figures of less than 1.400 BTU/lb A12O3 were achieved.

Jan 1, 1971

Recent work has shown that, in at least some instances of regional metamorphism, metamorphic diffusion has been restricted to such relatively minute distances (of the order of 1.0 mm and much less), that there is no clear, direct evidence of prograde metamorphic mineral reactions, and that metamorphic equilibrium does not appear to have been attained through even very small domains.A number of stratiform orebodies and their immediate metapelitic environments exhibit very large, seemingly "disequilibrium", assemblages of regional metamorphic index materials. One such, in north-eastern Australia, includes laumontite, prehnite, chamosite, stilpnomelane and related hydrous iron silicates, primary chlorite, sericite-muscovite, epidote, actinolite, biotite, almandine, andradite, metamorphic hornblende and clinopyroxene, scapolite, staurolite and sillimanite, all within a 20 metres length of a single diamond drill core. In this and several related occurrences it appears that metamorphism has involved very small scale in situ transformation of pre-existing materials rather than large-scale diffusion and reaction, and hence that the observed metamorphic minerals have probably been derived directly from precursor materials of sedimentary/diagenetic origin.It is concluded that the fluctuating seafloor interplay between warm, acid, concentrated hydrothermal waters with cold, alkaline, dilute seawater during stratiform ore formation, together with diagenetic processes, leads to the formation of a wide range of clay, chlorite, mixed-layer clay and clay/chlorite, and zeolite precursor materials and hence, later, to the complex assemblages of metamorphic minerals closely associated with some stratiform ores. Commonly included in highly localized assemblages of this kind are various minerals which, in conventional regional metamorphic studies, are generally regarded as indicating widely different grades of metamorphism.

Jan 1, 1982

By Van Deventer J S J

The first step in the design of a process to treat a possible economic precious metal deposit should be an examination of the mineralogy of the ore. Using this and other initial tests, the extractive metallurgist can design a process to treat the ore. In the field of precious metal metallurgy, little emphasis is placed on the mineralogical information available to the metallurgist. The information is of far more use to the geologist and the mining engineer. Diagnostic leaching was designed to open up the field of mineralogical analysis to the metallurgist. When a mineralogist looks at the deportment of gold in an ore, he is usually looking for an element which is present in parts per million, so that errors in sampling are multiplied dramatically. Diagnostic leaching offers a cheap, simple, practical alternative. In order to determine with which minerals the desired precious metal is associated, a specific mineral is first eliminated using a selective oxidative leach, and cyanidation is used to extract the precious metal (in this case gold and silver) liberated by the destruction of this mineral. The precious metal extracted can be measured in solution to give a fairly accurate record of the amount of the precious metal associated with that mineral. Furthermore, the residue from this first stage can be subjected to another selective acid leach, and the process repeated. The procedure can be varied to suit the mineralogy of the matrix material. At the end of this diagnostic leach the metallurgist is left with a complete record of the deportment of the precious metal. He can now use this information to design a metallurgical flowsheet to treat the ore. Diagnostic leaching is thus an analytical tool which can be used by the metallurgist not only to examine new ores, but also to look at problems occurring at existing plants. The procedure is not only limited to ores and residues but in fact can deal with any type of intermediary product that occurs on a plant. The information gained from analysing an intermediary product can give a useful indication of how well a unit process is working, eg flotation, roasting, etc.

Jan 1, 1992

By Scott A

The object of most blasting operations is to destroy the insitu structure of the rock mass so that mechanical equipment can efficiently excavate the rock fragments. In achieving this objective the blasting engineer is also concerned with minimising damage to the adjacent rock which forms the mine structure relied upon to provide support. Damage to this "structural" rock is undesirable but usually occurs as a result of two distinct processes: ò readjustment of stresses around the excavation as a result of the mining process itself ò impact of vibration and high pressure gases from blasting operations. Gross damage to mine structures from either cause is observed as visible alteration to the appearance of the rock structure in the form of cracking, slabbing, back or over break and visible displacement. Recent work at the Julius Kruttschnitt Mineral Research Centre (JKMRC) has shown that significant reduction in the strength of a rock mass can take place well before the onset of these obvious signs of damage. It has been demonstrated that the effect of blast damage on the behaviour of the rock mass can be many times more prominent than the effect of stress redistribution. This offers the blast design engineer the opportunity to significantly reduce blast induced damage to rock structure by modifying blasting practices. This paper introduces the current JKMRC postgraduate research projects investigating the evaluation and control of blast damage.

Jan 1, 1990

By Moorrees C

Tests show how that temperature and rate of sparging to remove carbon dioxide determine the rate of precipitation and the chemical and physical properties of hydrated magnesium carbonates precipitated from clarified magnesium bicarbonate liquors derived from crude magnesia. At temperatures above 55°C the product is largely in the form ofhydromagnesite, Mg5(C03)4(OH)2.4H2O Between I5°C and 55°C the major product is nesquehonite, MgCO3·3H2O, although partial hydromagnesite precipitation can be induced by a high rate of aeration.As a result of the reduced time required to bring about greater than 95 per cent magnesium precipitation, the higher MgO content of the product, the ease of product recovery from the precipitation vessel, and the lower energy requirement for thermal decomposition of the precipitate to magnesia, it is preferable to precipitate hydromagnesite rather than nesquehonite. Moreover, the magnesia produced from hydromagnesite is somewhat more reactive than that formed from nesquehonite.Using precipitate calcination temperatures less than 1000°C, the chemical reactivities of the magnesias formed from both precipitates are greater than those of the crude magnesias derived from Savage River magnesite itself. The magnesias would be suitable for most uses developed for caustic-calcined magnesia. However, for refractory brick manufacture, it would be necessary to briquelle the caustic-calcined magnesia. adjust the CaO and SiO2 contents and sinter at temperatures in excess of 1600°C. This would bring about an increase in the bulk density and induce the appropriate chemical bonding reactions.Dead-burned magnesia produced from Savage River magnesite by the calcination/carbon dioxide route would have very low B2O3 contents, typically less than 0.0001 per cent.

Jan 1, 1985

Difficult ground conditions in the area planned for placement of vent rises to the surface at the Porgera Goldmine led engineers directing the project to chose blind shaft boring methods of shaft construction from the available alternatives. Zeni Drilling Pty Ltd was first contracted in 1988 to install a group of three closely-spaced, steel lined shafts. The success of these led to an order for a fourth hole in the same group followed by two more, less than a kilometre. away, under a separate contract in 1992. All of the shafts were completed on.schedule to within one day. The only significant difficulty arose during commencement of the last shaft when the strata collapsed trapping the drilling tools and jeopardising the stability of the surface collar pad. The situation was corrected by innovative lining techniques and the project went on to finish on schedule. This paper discusses the application of various technologies associated with the project including aspects of geotechnical input, drilling fluid chemistry, mining engineering and logistics.

Jan 1, 1993

By Ross J. F

A pillar 'is a block of coal left in the first working of a coal seam for the purpose of supporting the superincumbent strata in such a manner that the winning out roadways will be safe to traverse by men and by the coal transport system.PRINCIPLES OF PILLAR EXTRACTION.The size of a pillar is chiefly dependent on the depth of cover, and in a lesser degree on the nature of the coal, or the condition in which the seam has been laid down. In a seam at 1,100ft. depth of cover, and assuming a spec'ific gravity of 2.5 overall for the cover strata, a pressure of 1,200lb. per sq. in. is the loading on the top surface of the coal seam before mining begins.When mining commences, and as the pillars are formed, an increased load is imposed on the coal left in the pillars, according to the percentage of coal extracted in the first working. Thus, if 25% extraction is taken in the first working, the load on the pillars is theoretically increased from 1,200lb. per sq. in. to 1,600lb. per sq. in. over the area mined. If this state of things went on indefinitely it would not be possible wholly to extract a pillar because of the extreme pressure tliat would be thrown on the diminishing portion; but, fortunately, another element, that of time, enters into and assists the process of extraction.If the superimposed strata were of an entirely plastic nature, this time factor could not operate, as the cover weight would settle instantly on the remaining portion of the p'illar and finally overwhelm it. The cover strata above a pillar generally have a certain rigidity which does not allow the superimposed weight to settle instantly on the pillar fraction, and it requires a period of time to elapse before the extra weight is felt by the pillar.The time factor varies widely, and is governed entirely by local conditions; it can only be determined by experience gained on the spot or in close proximity to the area of operations. It is dependent on the strength of the strata and its characteristics under bridging conditions.It is, therefore, logical to assume that the more rapidly a pillar can be extracted the greater will be the safety factor and also the percentage of recovery of coal.Up to the present time, the operation of the extraction of pillars in this country has been, with a few exceptions, a manual one, and before mechanization of Collieries can be fully accomplished, the process will have to be performed mecharrically.

Jan 1, 1947

By Coulborn W. T, Glasby G. P, Maylan M. A

Research cruises by HMNZS 'Tui' (1986) and RV 'Moana Wave' (1987) investigated the geology, geophysics and seafloor mineral resources of Manihiki Plateau in the central Pacific Ocean.Manihiki Plateau is a large (500,000 km2) mid-ocean platform that rises 3000 m above the abyssal plains of surrounding ocean basins (depth -5500 m). Its foundation evolved about 112 Ma ago by massive outpouring of basaltic lavas at a plate triple junction. The plateau is blanketed by a 900 m thick sedimentary section comprising (i) mid-Late Cretaceous volcaniclastic sandstones / siltstones grading upwards to limestones / chalks and (ii) -500 m of Tertiary nanno-foram chalks and oozes. Cores from DSDP 317 drill-site on the Manihiki High Plateau indicate that the volcaniclastic sediments contain native copper and some thin beds rich in organic carbon.

Jan 1, 1990

The decrepitation technique is a rapid means of measuring abundances, temperatures and to some extent the fluid compositions, of fluid inclusions in transparent and opaque minerals. The method has been used to investigate the hydrothermal fluid systems associated with gold mineralisation in the Tennant Creek, Pine Creek and Halls Creek Goldfields. At the Enterprise Mine, Pine Creek, several different stages of quartz veining are distinguished and within these, gradational changes in fluid temperatures and compositions help to define the centre and nature of the thermal system responsible for the mineralisation. In the surrounding Pine Creek region and at Tennant Creek and Halls Creek, the results were applied on a regional scale to characterize outcrops and aid in the discrimination between potentially mineral- ized and barren outcrops. The decrepitation method involves the heating of a small (lgm) sample of crushed and sized grains up to as high as 800 degrees celsius. During the heating the fluid inclu- sions within the grains develop sufficient internal pressure to physically burst, the temperature of such bursting being dependent on the type of fluid and the prevailing tem- perature at the time the inclusion was originally trapped. The resulting tabulation of the number of inclusion bursts per 10 degree temperature interval is plotted as a histogram of decrepitations versus tempera- ture and called a decrepigram. The decrepi- grams frequently show several distinct peaks at different temperatures which are caused by different populations of inclusions in the sample. The areas of the peaks indicate the abundances of inclusions in each population while the shape and mean temperature of the peak provides a guide to the type of fluids involved. Of particular importance in this study is the presence of decrepitation peaks at fairly low temperatures (around 2000 C. These are characteristic of C02 rich fluids which build up internal pressure very quickly when heated. The Enterprise Gold Mine at Pine Creek comprises a number of overlapping quartz vein systems hosted by Burrell Creek Formation sediments. The geology of this mine has been described at this conference by Dann and Delaney, who have defined several distinct stages of quartz veining based on structural, mineralogical and physical features of the veins. For this decrepitation study, 19 quartz samples from the mine and environs, including some from each stage of veining were collected. These results suggest that there are 4 major vein types, within 3 of which additional small variations can be discerned which are due to gradational changes in the temperatures and fluid compositions in the mine area.

Jan 1, 1984

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996

In 1969, Queensland Mines Limited obtained two large Prospecting Authorities in Arnhem Land, Northern Territory, Australia. The Nabarlek uranium deposit containing some 12 000 t of U308 was discovered on one of these in June 1970. Mining and stockpiling of this deposit were completed in 1979 and processing to yellowcake, which commenced in June 1980, is expected to occupy an 8-10 year period. The continuation of exploration, essential for the company to become a longer- term producer, was inhibited in 1972 by a Federal Government "freeze" on exploration in Aboriginal Reserves in the Northern Territory. Subsequently, the procedure for explorers to gain access to exploration areas in Aboriginal land was radically changed by the proclamation of the Aboriginal Land Rights (Northern Territory) Act 1976. As a result of this Act and the associated administrative policies adopted by Governments, Queensland Mines Limited has not yet regained access to the exploration areas it formally held in the early 1970's.

Jan 1, 1986

By Pyrih R, House A, Shangraw J, Silva AJ

Sunbeam Mining -Corporation has the inten mine with heap leach gold recovery, near spent ore indicated a relatively high ar topographical configuration, the spent across a small drainage and a lake. Du permit for spent ore disposal from th agencies, concerns about the potential contamination by the arsenic were expres conducted extensive studies to addre contamination. These studies consiste( geochemical and geotechnical parameters underlying the proposed disposal si geotechnical investigations were also hydrologic characteristics were include with the use of an IBM PC computer. :ion of opening an open pit gold Stanley, Idaho. Testing of the ?enic content. Due to the local ore was planned to be disposed :ing the process of obtaining a federal and state regulatory for surface and ground water .ed. Sunbeam Mining Corporation is the potential for arsenic of laboratory testing of both of the spent ore, and the soils te. Field hydrogeologic and -onducted. Local climatic and 1 in the analysis of these data Conclusions of studies indicated that although the seepage through the spent ore disposal would contain an elevated dissolved arsenic content, the hydrologic and geochemical characteristics of the site would prevent arsenic migration into the local ground water system. The attenuation of arsenic on soils with high clay content, and dilution after reaching the ground water table would lower the arsenic content to acceptable Concentrations.

Jan 1, 1988

By K Heiskanen, R A. Grau

Gas velocity (Jg) measurements conducted close to the froth-pulp interface over the cross-section of a flotation cell reveal how efficiently the incoming air is being dispersed throughout the volume of the cell. Furthermore, measurements of Jg at deepest locations in the cell provide valuable information about air recirculation and dispersion conditions in the bulk volume of the cell. Gas velocity in flotation cells has predominantly been measured by a transient capture of gas in a graduated probe. In this project, a new sensor for measuring gas velocity in an on-line manner was developed. A probe is partially immersed in the flotation machine, below the froth-liquid interface. The probe is used to collect the rising air bubbles from the liquid phase. The liquid-froth interface is shifted into the probe under vacuum. A controlled vacuum is kept inside the probe. As air bubbles burst inside the probe, the excess of air is continuously removed from the probe via suction. The removed air is measured using a mass flow meter. The fully automated sensor allows us to continuously measure Jg at different location in a flotation machine. An experimental programme was carried out in a 10 cm diameter laboratory flotation column to determine the accuracy and repeatability of the automated sensor. The new sensor was used for evaluating gas dispersion conditions in a 215 litre transparent laboratory scale flotation cell. Gas velocity distributions along the radial and axial directions of the cell were measured over a wide range of operating conditions. The operating conditions in the cell were modified by altering impeller speed and air flow rate. Two different rotor-stator mechanisms were utilised to disperse the air in the cell, the MultiMix and the FreeFlow mechanism. In this paper, a description of the gas velocity sensor is given, and the results of the experimental work are discussed in detail.

Jan 1, 2005

By Harris RW, Wood BR

At any given time, the tidal force subjects massive regions to a spatially uniform load. The deformation of any large structure due to these forces is proportional to the elastic properties of the structure. In this aspect, the tidal force applies a load in a manner similar to that of a large-scale testing machine. Any anomalies in the measured tidal response must reflect alterations in the average elastic response of the massive structure. In the present work, tidal tilt measurements obtained in the wall of a large dam are used to infer changes in the response of the dam to applied loads. In particular, it is found that the dam response has changed by approximately 13 percent, on average, for two monitoring periods separated by 5 years. It is possible that these changes were produced by the different volumes of water in the dam for the monitoring periods. The tidal measurement technique can also be applied to monitor changes In the average structural response of large underground and surface masses relevant to coal and metal mines.

Jan 1, 1992

By D A. Kepert, D Clark

During early 2004, Fortescue Metals Group (FMG) began an aggressive exploration and drilling program in the Chichester Range, targeting iron enrichment developed in the Nammuldi Member at the base of the Marra Mamba Iron Formation. The timely recognition by FMG of distinct zones of (hypogene) microplaty hematite (mplH) enrichment overprinted by extensive supergene mineralisation led to an early reappraisal of the geological history of the area and characterisation of the possible structural and stratigraphic controls on mineralisation. Regionally, the Chichester Range dips gently at less than 5¦ to the south, however, detailed mapping shows that this regional limb is overprinted by low amplitude, long wavelength, north/south to northeast/southwest trending folds. The locations of major structures in the Marra Mamba Iron Formation, combined with spectral analysis of known mineralisation, allowed extrapolation and prioritisation of exploration target areas. The delineation under cover and understanding of these structures was enhanced by detailed airborne magnetic data. Recognition that supergene mineralisation was associated with a palaeotopography that continued significantly under cover to the south under sediments of the Fortescue River valley led to the discovery of extensive supergene mineralisation together with additional mplH mineralisation. A model for the landscape evolution and preservation of enriched Nammuldi Member was generated in order to help communicate both the complexities involved with targeting drill holes beneath cover and the potential limits to the lateral extents of mineralisation.

Jan 1, 2005