Search Documents

By Firmin K

The Mt. Tom Price orebody of Hamersley Iron Pty. Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the orebody, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control'of products based on selective mining is the production of advance data, on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades Are determined from assay of samples taken from blasthole cuttings.

Jan 1, 1980

Every text book for blasting in Japan says that Hauser's law can be applied for practice. But recently it came true that there was no historical record about him and no actual datum of his own or other's to testify. According to his theory, the funnel ratio N = r/W in crater test is inversely proportional to the rock strength and proportional to the explosive amount: where r is the radius of crater and W is the burden. But experiment showed the opposite result, and revealed new information. Two kinds of experiment, crater test and boulder blasting of mortar, were carried out to investigate the effects of rock properties on blasting. The material used for test 1 and test 2 was a mortar block (60cm)3 cube, 4 vertical faces of which were used for crater test. The results from Test 1 and test 2 were summarized as follows. The funnel ratio ranges between 2.5 to 4.5 in proportion to rock strength and burden. The standard ratio of 1, reported by Hauser, was not observed in any instances. It was also noted that the funnel ratio is independent of the explosive amount. The material used for boulder blasting, test 3, was a mortar block (40cm)3 cube, in the middle of which was located a vertical borehole for the explosive charge. The results of test 3 were as follows. The necessary explosive amount for boulder blasting is in inverse proportion to the mortar strength. Fragmentation and throw are proportional to the mortar strength.

Jan 1, 1990

Cerro Matoso (CMSA) in Colombia produces ferro-nickel from lateritic ore containing approximately three per cent nickel, using a Rotary Kiln - Electric Furnace (RKEF) process, in which the calcining of the mineral within the kiln is second in importance only to the smelting of the mineral in the Electrical Furnace. This article discusses the installation and operation of an expert system to control the kiln of CMSA. In the CMSA process, the run-of-mine ore is crushed, homogenised, dried and mixed with a small percentage of coal, before being heated up to 900¦C in a rotary kiln in the presence of natural gas mixed with air in a controlled proportion (air/gas constant ratio). The final objectives of the process are the following: ò To reduce to a minimum the iron and nickel oxides in order to convert these into metallic ions; this is a reduction process to facilitate largely the smelting in the electric furnace. Since the reduction is made with natural gas, it is much more economical than the subsequent complete reduction in the electric furnace, since electrical energy is much more expensive by unit of processed mineral. ò To heat the mineral as much as possible to facilitate the subsequent smelting. ò To eliminate totally the moisture content of the ore. An expert system with fuzzy logic was commissioned in 1994 for the control of the kiln and it has operated with good results ever since.

Jan 1, 1996

Instantaneous outbursts of coal and gas have occurred in Australia in the Sydney Coal Basin since 1895 and in the Bowen Coal Basin since 1954. The largest has been about 500 tonnes of coal and so their magnitude and character have not approached those experienced in some other countries. The occurrence of CO2 with some Australian cases provides some similarity with the worst affected areas in France and Poland.The proneness of seams depends on coal rank and seam gas composition, among other factors. The proneness of places depends on depth, structure, intrusion, tectonism and other factors affecting the geometric, physical and chemical uniformity as well as details of mining. As a phenomenon due to gas and stress, prevention can be achieved by relief of high gas and/or stress condition. Alternatively, controls can be applied to render mining safe for personnel. Unfortunately day-to-day prediction is not widely and reliably achieved to allow selective use of prevention or control. The initial rate of desorption is the most promising day-to-day indicator.Various researches include gas conditions and parameters, stress and failure conditions and parameters, coal variables and geological variables in relation to prediction, prevention and control. Some assistance in research may derive from study of analogous phenomena of instantaneous outbursts of salt and other rocks and gas. It is concluded that in the Sydney and Bowen Basins, any coals with less than 30 per cent Volatile Matter (VM) ash free dry (afd) at depths over 200 m could be prone. Proneness increases with depth, with lower volatile content, with geological disturbance including faulting, intrusion and recent tectonics, with increased CO2 in seam gas, with narrow work and with other factors. Much more research is needed.Unfortunately outbursts are needed too, to provide the research with realistic data. With the problems of mechanism and prediction still being unsolved much research remains to be done. No present aspect of research is satisfactorily resolved.

Jan 1, 1983

By Burgess J, Brownrigg A

The world steel industry underwent rapid growth from 1950 to 1970. Since that time, production growth has been relatively slow, with declining production in the developed countries and increasing production in some newly developing countries. Since 1970, Western World crude steel production has been static at around 450 million tonnes, with cycles around this level in a 100 million tonnes band.

Jan 1, 1992

By Gonzalez JM

The Pao gold prospect in N. Luzon, is an example of a high sulphidation epithermal gold system hosted in Mid-Tertiary alkaline volcanics, in the Philippine Arc. Styles of mineralization include: quartz-enargite veins, vuggy silica alteration bodies, and pervasive low grade (0.5ppm) gold mineralization, associated with kaolinite-pyrite-quartz alteration, and geochemically characterized by high As and Hg. Early magnetite-epidote-chlorite alteration linked to an unexposed granitoid is overprinted by an extensive zone of advanced argillic alteration (kaolinite-pyrite-quartz). No alunite is recorded. Important controls of mineralization include; a broad anticline intersected by axial faults, permeable pyroclastic units, and upward confinement of the alteration system by a highly impermeable, clay-rich volcanic unit. At this stratigraphic position the most important mineralization waz developed. The Pao high sulphidation system is not closely related to a stratovolcanic centre, and has formed subsequent to deformation of the volcanic field. It may, however, be related to an unexposed comagmatic intrusion.

Jan 1, 1990

A case study of a landslide, which threatened vital infrastructure essential for the continuous operation of the Ok Tedi copper mine is presented. The paper presents a detailed description of the land- slide, outlines the assets at risk, and how the issue was addressed. This included the consideration of remedial options and the im- plementation of the most economically sound and geotechnically feasible remedial design which was completed within budget and on schedule. The paper is intended to highlight the responsibility of a mine based Geotechnical Engineering section in providing essential geotechnical investigations, design and professional advice on addressing stability issues in the infrastructure region.

Jan 1, 1997

By Baafi EY

Open cut mining in Australia is facing the greatest challenge in its history in attempting to compete not only with other operations internationally, but also with underground operations domestically. Most flat dip and shallow depth surface-mineable coal reserves have been depleted during the last two decades and new open cut operations must extract deeper coal deposits. As open cut coal mines move into deeper areas and the stripping ratios increase, the relative cost of overburden removal also increases. It therefore becomes even more important to design the mine around the optimum overburden removal scheme. The deeper mines are usually multi-seam operations with a more complex geology and with more geotechnical and hydrological problems. Deeper mines are subjected to greater problems requiring more detailed mine planning and design, such as selection of the optimum mining method and pit layout. In planning and design of such operations, the number of alternative methods which need to be considered is consequently greater.Dragline productivity and its stripping capabilities are directly affected by the selection of digging method, strip layout and pit geometry. Every mine has a unique combination of geological conditions. The operating methods that work well at one mine may not necessarily work at another site. Selection of an optimal stripping method, strip layout and pit geometry for a given dragline must be considered with respect to the geological conditions of the mine. With increasing geological complexity of Australian strip mines, it is becoming more important to use sophisticated techniques such as computerised mine planning methods to assist in optimising dragline operations.

Jan 1, 1998

By Bin H

East Guangdong tin province overlaps the southmost part of the mesozoic magmatic arcof continental margin type in Southeast China and is dominated by mesozoic syntectic magmatism,which associated to tin mineralization. It is distinguished from Nanling tin province but quite close to NW Bolivian tin province in both tectonic and magmatic relations.Tin deposit's mostly of cassiterite-sulfide, cassiterite-silicate formations are localized along exsocontact zone of granitoid batholith or stock, boundary area of volcanic depression, or, within volcanic edifice. Petrochemistry studies show tin was concentrated as intermediate-acidic magma evolved by fractional crystallization. Xiling tin deposit of vein type related to extrusive... the lava dome was formed at T C 221-301 and at very shellow depth,seems to correspond to type A in classification for Bolivia tin deposits by J.N.Grant. Tashan tin deposit of dissemination type related to hypergene intrusive facies,with mineralization occured in endocontact zone of granite porphyry dykes is considered as porphyry type,which spported by H-0 isotope and gas-liquid inclusion evidences. It formed at T C 250-430, comparable to Bolivia porphyry tin deposits,but at a greater depth 1.3 3.0km.A model for known tin deposits in East Guangdong was worked out. A good prospecting perspective was revealed for the potential type of tin deposit in East Guangdong--subvolcanic porphyry tin deposit.

Jan 1, 1990

Chromite ores have a long history of low pricing and for AustraliaÆs only chromite mine this has been a particularly tough challenge, especially as the mine is located nearly 400 km from the nearest port at Port Hedland. A stockpile of chromite fines (-16 mm) has been built up since 2003. The opportunity to develop a facility to treat this material to produce a chip (-16 + 1 mm) product and a sands (-1 mm + 45 micron) product was taken when the price increased to above US$140/t. A simple add-on plant containing a heavy media cyclone circuit for the chips and a spiral circuit for the sands was designed and developed. During construction of the fines plant the price of chromite reached a level where the payback for the entire project was less than eight weeks. Soon afterwards the price and the demand for chromite plummeted and the site was put on care and maintenance, except for the commissioning of the fines plant. This put considerable pressure on whether to continue to operate the plant or to place it in care and maintenance. Times of boom and bust provide management with almost totally opposite views. By not taking a conservative view on prices and costs, the effect of extremely low prices and minimal demand can be devastating to a good project. Designing and building plants with conservative costings in boom times gives a greater chance of keeping projects alive during the bust periods that tend to follow.

Jan 1, 2009

By D Craw

Otago Schist and Klondike Schist are two Paleozoic-Mesozoic metamorphic belts on the circum-Pacific margin in which there has been a long history of abundant alluvial gold mining, but only minor hard-rock gold mining.   Modern exploration for hard-rock gold is ongoing in both belts, and the active Macraes mine in Otago (>2 Moz production) highlights the hard-rock potential of the geological setting of these belts. Hard-rock gold mineralisation in both belts formed in the latter stages of schist exhumation, after rocks were subjected to major regional ductile folding and then uplifted through the brittle-ductile transition. The majority of known hard-rock gold-bearing systems in both belts consist of well-defined, but generally discontinuous, vein swarms. Most Otago veins are hosted in steeply dipping post-metamorphic normal faults and fractures. However, the Macraes mine is hosted by a late-metamorphic shear zone, and much ore is sulphide-impregnated auriferous schist. Goldbearing veins in the Klondike schist are hosted primarily in extensional sites associated with post-metamorphic compressional structures. Some disseminated sulphide mineralisation is associated with Klondike veins and this is important as it extends the exploration target for these veins. No foliation-parallel late metamorphic mineralisation has been identified in the Klondike but exposure is relatively poor compared with Otago and both schist belts are highly prospective for deposits of this type.

Jan 1, 2007

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

By Regan R

Appin Colliery mines the Bulli Seam with a gas composition of 98.5% methane and 1.5% carbon dioxide. Relaxation of the strata generally occurs to below the base of the Wongawilli Seam, some 40 m below the Bulli Seam, and approxim- ately 125 m above the Bulli Seam, for longwall face widths of 135 m or more. Previous exper- ience showed that when longwall faces were mined for a distance approximately equal to the face width, the mine ventilation could not provide sufficient dilution due to methane emissions from the underlying measures. Postdraining downholes were drilled to intersect the Wongawilli Seam below the operat- ng longwall. These holes were connected to an underground to surface gas range and various suction levels were applied to improve gas drainage. The resulting gas flow rates and purity from all the downholes were regularly monitored and peak flows in some holes exceeded 160 1/sec. The surface plant drained almost 20 million m3 of gas for the period July 1981 to January 1982 at an average methane purity of approximately 70%. Distinct patterns emerged for different downholes from curves illustrat- ing their variations in flow rate with distance subsequent to passage of the longwall face. The difference between free flow characteristics and those obtained with the application of

Jan 1, 1982

By McDonald K. J, Flann R. C

A liquid phase sintering (LPS) process for preparing basket anodes from nickel powder has been scaled-up and the innuence of compact green density and sulphur content, as well as sintering conditions (period and syngas now.rate) on the perfonnance of anodes has been evaluated. The product anodes have been tested in an industrial electroplating tank. It is concluded that if anode residues are to be minimised, then with a sintering temperature of 960"C, compact green density needs to be as high as economically achievable (85 - 87 per cent density of solid nickel) and the sintering period approximately 40 minutes. With these constraints, if residual sulphur contents of anodes are to be kept as low as those of commercial anodes, then the sulphur content of the green compacts would need to be less than 1670 ppm. At the same time, it is also found that residual sulphur concentrations as high as 2000 ppm are beneficial to anode pcrfonnancc and not detrimental to the quality of the electroplate. The ability of the LPS process to produce marketable nickel anodes for the electroplating industry is clearly demonstrated.

Jan 1, 1993

By Tuckey SH, Wake BA, Ariti J

Astute exploration on the northern Minahasa Peninsula, North Sulawesi, resulted in the discovery of the Toka Tindung, Pajajaran, Blambagan and Araren low-sulphidation quartz-adularia vein and stockwork gold-silver deposits. Combined, these deposits have estimated mineral resources in excess of I Moz gold at an average grade of 2.8 gAu/t and 7 gAg/t and are known as the Toka Tindung Gold Project. Gold typically occurs as fine grained electrum and is often associated with acanthite. The structurally controlled mineralised veins are hosted by Late Pliocene plagioclase and pyroxene-phyric basaltic andesite volcaniclastics and flows which form part of the Early Miocene to Pleistocene Sulawesi-East Mindanao Arc. Silica-adularia alteration dominates the volcaniclastic host of the Toka Tindung deposit. K-Ar dating of vein adularia indicates a 2.16 ¦ 0.04 Ma mineralisation age. Relatively narrow envelopes of silicification and argillisation surround the chalcedonic silica, quartz and adularia veins, stockworks and breccias at the other three deposits. Remnant hydrothermal breccias, chalcedony and anomalous arsenic, antimony and mercury indicate these gold deposits were part of a mineralised geothermal system.As of June 1997, Aurora Gold Ltd is finalising a feasibility study on exploitation of the four deposits and treatment of ore through a centrally located conventional CIP plant. Subsea tailings disposal is anticipated. Favourable metallurgy of the ore and logistics of the project area assist in minimising capital requirements.

Jan 1, 1997

By Mendeckl A. J

Anglo American Corporation has always viewed technological development as vital and as such has placed research and the implementation of new technological practices high on its priority list. Support is given to a number of research institutes but a significant degree of reliance is placed on in-house research carried out at individual companies and at the Group's main laboratory complexes. The Corporation's interests are diverse with advanced practices and innovative technology ranging from new battery technology with wide application to deep level shaft technology with very specific application. In this paper, we aim to concentrate on a particular system developed primarily for use in seismically active deep mines. The system has proved to have far wider application and has the potential to be further enhanced to meet the needs of users across a broad range within the industry and even beyond. As the nature of this conference is to inform delegates of advanced mining practices, we should simply mention that we could have talked on subjects relating to the advances made in deep level winding technology including winder drive and brake control to alleviate dynamic rope loads, shaft steel design for high pay load high speed winding and shaft safety systems such as slack rope devices and moving lip loading facilities to cater for rope stretch. Other areas of interest relating to refrigeration using ice technology or non-explosive rock cutting using diamond wire or saw technology could also have been of interest. As the South African gold mines become deeper and the problems associated with depth become more acute, answers had to be found and systems developed to cope with very high rock stress and the related seismicity. The fundamental understanding of the behaviour of the rock mass has always been important but became critical on our mines to ensure the safe extraction of the orebody. Basic research into and the application of physics, applied mathematics, seismology, rock mechanics, electronics and computer technology have helped us to develop the Integrated Seismic System - Integrated because of the system's abilty to monitor seismic and non-seismic sensors simultaneously and because it encompasses data acquisition, processing and interpretation into one system. The system which is in use at all our gold mines has found application not only in South Africa but also in such locations as Australia, Chile, Canada, Europe and Japan. A highly motivated team of scientists under the leadership of Aleksander Mendecki developed the majority of the hardware and software needed for the system. In essence, the system allows us real time monitoring of energy release and stress transfer data that with the aid of modern computers is turned into useful information. The information so obtained has allowed us to improve our mine and extraction designs to minimise the inherent hazards. The system has proved to be an extremely useful management tool as substantiated by the demand for the product. The paper is intended to convey to the reader the technical concepts and the presentation is intended to demonstrate the usefulness of the system.

Jan 1, 1995

A new experimental procedure for determining the solids flux curve is detailed. The procedure is based on measuring the concentration at various heights of a bed of settled solids formed during a semi-continuous sedimentation test. Unlike conventional thickener area calculations, the test procedure demonstrates the dependence of the flux curve on the system feed flux. At a given feed flux, there was good agreement between the solids flux curve determined by the method and continuous sedimentation results. The widely used method of Kynch was found to be restricted to relatively high effective feed fluxes and consequently there was poor agreement with continuous tests at low feed fluxes. The flux curve determined by the method of Coe and Clevenger was invalid for all feed fluxes. A case study shows how the required thickener area would vary for a number of fine coal processing options.

Jan 1, 1989

By Armstrong M

The highest grades of the Porgera gold deposit, Papua New Guinea, are contained in Zone 7 due to the presence of the Roamane fault, which acted as channelway of the gold-bearing fluids. Prior to the development and underground mining of this fault-controlled high-grade zone it was critical to provide grade estimates of relatively small mining units, and of the proportion of mining units above cutoff. To be applicable to Zone 7 of Porgera a grade estimation method should account for the following:1. the highly skewed and apparently lognormal distribution of the grades,2. the rapid drop off of the local mean grade and the variance as the distance to the Roamane fault increases,3. the presence of high grade pockets in the footwall, away from that fault, and4. the existence of variograms for the logs with sills parallel to the fault and without sills perpendicular to it.

Jan 1, 1990

The Olympic Dam smelter utilises Outokumpu Oy, flash smelting technology to produce blister copper direct from high grade copper concentrate.This paper describes the unit processes involved, including filtering/drying, materials handling, smelting, gas/dust handling, waste heat recovery, sulphur fixing, anode refining and casting.

Jan 1, 1993

By Ranklin W. J, Swinbourne D. R

Lead blast furnace slags contain typically 10 - 20 mass per cent Zn. The zinc can be recovered by slag fuming, in which a powdered coal/air mixture is injected into a molten slag bath. Volatilised zinc is recovered as zinc oxide from the gas and processed hydrometallurgically to produce zinc metal. The ISASMELT continuous lead smelting process in operation at Mt Isa produces a slag containing about 12 per cent Zn which is currently granulated and stockpiled. This slag could flow to a further bath-smelting reactor for continuous zinc fuming. Rather than collecting the zinc as fume from such a process, one option would be to recover it using a lead splash condenser. The success of this operation would depend on the composition of the gas produced, in particular the concentrations of gases capable of reoxidising zinc vapour, viz, carbon dioxide and water vapour. The aim of this investigation was to determine the smelting conditions for a bath-smelting process such as ISASMELT or SIROSMELT which would produce a gas similar in composition to that from an Imperial Smelting Furnace by thermodynamic modelling of the process using the CSIRO Thermochemistry System. It was found that such a gas could be produced if coal injection and oxygen enrichment of the combustion air to at least 40 per cent 02 were used. However, the off-take gases must be conditioned by addition of methane to reduce the water vapour content to acceptable levels. An addition rate of ten per cent of the off-gas flowrate was found to be adequate. Addition of methane to the off-gas had the added advantage of cooling the gas from the bath temperature to a temperature suitable for normal lead splash condenser operation.

Jan 1, 1993