Search Documents

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Electronic Detonators have made significant strides over the last few years, both in quality of product and performance in different blast applications. The precision and flexibility of the SMARTDET units provides the mines with a powerful means of controlling blast results, giving both cost and productivity improvements. The SMARTDET Electronic Detonator System, robust and easy to use, has been successfully deployed over the last 18 months in improving mine productivity and creating safer working conditions in both quarrying and long-hole stoping. The key to the improvements has been the precision and flexibility of the electronic timing, and the ability of the mine personnel to grasp the concept quickly and use it effectively.

Jan 1, 1999

The Australian minerals sector has a shortage of skilled professionals to satisfy an industry that is experiencing renewed vitality. Graduate numbers are low throughout Australia and the world, while economic rationalisation is seeing many educational institutions downsize, or even close, their minerals-related programs. In addition to requiring more entry-level graduates, minerals producers are looking to update the skills of their current workforce to keep up with the industryÆs continuing technological revolution. To address the issue the Minerals Council of Australia (MCA) endorsed collaboration between several Australian minerals producers and a team of universities to generate the Mineral Tertiary Education Council, or MTEC. MTEC recently initiated a venture to increase the availability of professionals with relevant skills to the minerals industry. Primarily aimed at delivering postgraduate programs, the initiative will allow graduates from other disciplines to æconvertÆ to the minerals sector as well as provide professional development training to an existing work force. This venture represents a novel approach in that courses will be delivered by more than one institution and will employ innovative teaching materials with flexible and remote delivery formats. The programs will cater specially for professional development in the minerals sector, which generally requires high flexibility due to the nature of work conditions and locations.

Jan 1, 2004

By Riley S. J

Ranger Uranium Mine is located within the Alligator Rivers Region of the Northern Territory of Australia and surrounded by the World Heritage listed Kakadu National Park (Figure 1). The mining operation is currently producing about 1500 tonnes of uranium oxide annually, as well as considerable volumes of waste rock, low grade ore and tailings. The rehabilitation of the project should ensure that the radioactive mill tailings and other contaminants remain contained for at least 200 years, as required by the existing guidelines (Commonwealth of Australia, 1987). The present uranium mining operation is regulated by the Northern Territory Department of Mines and Energy who must refer to the Environmental Requirements when considering regulatory options. These Environmental Requirements were agreed by the

Jan 1, 1994

By Seib W

In cut-and-break rock excavation use is made of the fact that breaking rock in tension towards a free face requires a specific energy of excavation which is small in comparison with that required for rock excavation using conventional tools operating by a process of indentation of the rock.The process of cut-and-break excavation comprises firstly a cutting step in which a groove is cut into the rock surface, followed by a breaking phase in which a tool is inserted into the cut in order to break the rock adjacent to the cut.

Jan 1, 1992

The Managalase area is remote and little visited by geologists or prospectors. Yet it holds the key to the tectonics and petrology of this part of Papua. The eastern Managalase plateau (M, Figure 1) lies between the Hydrographers andesite volcano (H) and Sesara shoshonite volcano (S) to the south of Popondetta on the Papua Peninsular. It contains over 30 small volcanic centres in an area of only 400 km2 . To the south and west lies the basic-utrabasic belt (B-UB) of the Morobe arc. This is the leading edge of oceanic plate obducted over the Owen Stanley Metamorphics during the lower Eocene time. To the east and southeast lies the Cape Vogel geosyncline where the western end of the Woodlark basin spreading centre enters mainland Papua. The extension of the spreading centre as a suture might pass as far as the southern margin of the Musa Coastal plain. A new pattern of plate tectonic motions has been determined by the global positioning system and the southern margin of the Woodlark plate has been redefined (Tregoning et al, 1998; Taylor, Goodliffe and Martinez, et al, 1999). The Managalase plateau is margined by two inferred faults. These outline a cusp protruding from the main basic-ultrabasic belt where these rocks are near the surface. The westerly arm of the cusp passes through the centres of the Hydrographers and Mount Lamington andesitic volcanoes. Mount Lamington overlies Quaternary alluvium and underlying Tertiary sediments (Arculus et al, 1983) but members of the basic-ultrabasic belt crop out on the southern flanks. The easterly arm of the cusp is an inferred shear zone (and ? fault) connecting up with the terminus of the suture on the Musa coastal plain. Movements on the two faults forming the cusp are thought to have produced the conjugate N-S, E-W faults on the plateau (Ruxton, 1966). To the east, and isolated, are the two large andesitic stratovolcanoes of Mounts Victory (V) and Trafalgar (T) which together form Cape Nelson. Mount Victory was last active in the 1890s. The Waiowa shoshonitic volcano explosion centres (W), last active in 1943 - 1944, lie near the suture adjacent to the actively rising Goropu mountains. Extension in these mountains is clearly demonstrated by the soil profiles being skeletal along a bounding fault and ageing uphill. The incision of small parallel ravines also dig deeper further upslope from the fault. To the south-east of Mount Suckling (K) the Dayman Dome is also an expanding mass. The Owen Stanley fault is parallel, and located to the south of the suture. The Mesozoic metamorphics form the backbone of the Papuan Peninsula. The intramontane Musa Trough is thought to date from the mid-Tertiary. At the eastern end of the trough Pleistocene and Recent ultrabasic breccias and alkali basalt crop out (Green, 1961).

Jan 1, 1999

Since the introduction of the Neil George Five Point Safety System, to the underground sections of The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines in March, 1969, the Disabling Injury Frequency Rate has been halved and shows signs of contin- uing to fall. The total accident frequency rate has also fallen, although the decrease has not been as significant. Before the introduction of the Neil George Safety System, analyses of the direct causes of accidents showed that approx- imately 25 per cent were caused by "unsafe conditions", while 75 per cent were attribu- table to "unsafe acts". Within twelve months of introducing the system, these percentages had significantly changed to 7 per cent unsafe conditions and 93 per cent unsafe acts. Today, the figures are 3 per cent and 97 per cent respectively, and these figures clearly show that the main emphasis in the current programme must be directed towards making the operating men safety conscious. The effort must be focused on changing the minds of men.

Jan 1, 1975

By A Sinuhaji, R Poedjono, G Flumerfelt

PT Freeport Indonesia is currently building the DOZ mine. It is a 25 000 tonne/day block caving operation which is scheduled to reach designed production levels by the fourth quarter of 2002. This paper describes some of the issues and challenges faced by the operation when introducing a new undercut method part way through the project. Advantages and disadvantages are discussed as well as the expected benefits of the new method.

Jan 1, 2002

The purpose of this paper is to outline the basic policy problems for good community relations programmes in the resource extraction industries of Papua New Guinea. The main focus of the paper will be on defining and analysing those problems which lie on the landowner side and which are still not widely understood within the resource extraction industries despite several decades of turbulent experience. Many of the companies operating in the resource extraction industries of mining and petroleum and gas have in recent decades adopted, by choice or necessity, 'good corporate citizen' policies. Some of these companies now pursue ethical business, environmental and community relations policies. Some have adequately funded and well-trained staff in their community relations departments. Although different industry sites scattered over Papua New Guinea show significant differences in their experience of social conflict, I argue here that a good deal of this variation has less to do with the differences between the companies' public relations policies and their effectiveness and more to do with the conflict causing features of indigenous society. Experience suggests that even a company well-equipped with good intentions, good policies and good staff may experience serious difficulties in maintaining good community relations in Papua New Guinea. Many of these difficulties, I argue, can be traced to causes that lie, essentially, within the structure of Papua New Guinean communities and in the customs and social relations of Papua New Guinean peoples. Accordingly the attention of this paper is focussed on the conflict causing aspects of Papua New Guinean society. It is true, to the point of being a cliche, that Papua New Guinean societies are oriented very strongly towards achieving consensus and social harmony. In this regard Papua New Guinean communities differ significantly from, say, Australian communities. My purpose here is not to denigrate this aspect of Papua New Guinean societies but, rather, to point out that the drive for consensus is driven by the desire to avoid its opposite, dissensus. This paper sets out to define the dissensual aspects of Papua New Guinean societies and my special interest is in those conflict producing aspects of Papua New Guinean societies that are most resistant to the mechanisms that are designed to create social harmony. A survey of the recent history of industry and community relations in Papua New Guinea indicates that there are three main factors present on the landowner side which are liable, separately or through their interaction, to cause difficulties. These factors are respectively generational challenge, social boundaries and custom variability and I shall discuss each of these in turn.

Jan 1, 1997

By M Hilden, G Forbes, Z Ye, M Yahyaei, F Reyes, V Jokovic

Soft sensors offer several practical advantages for the process control of comminution circuits by combining multiple conventional sensors and other data sources with real-time analysis using mechanistic, phenomenological or machine learning models. While there has been a growth in the use of machine learning techniques for developing soft sensors in minerals processing applications, this paper describes advantages and challenges of using soft sensor models developed on the basis of process knowledge. Recent experience with three new soft sensor technologies developed by the authors are discussed. The Mill Filling Inference Tool which has been implemented at several mine sites, compares SAG mill load cell and power draw measurements with outputs of a semi-mechanistic power model to estimate the mill ball and total filling in real time. The progressive wear of the mill liners is modelled, allowing the model to correct the load mass due to the mass loss automatically and to estimate the charge trajectory. This information enables the mill to be operated more confidently near its limits. A coarse-ore stockpile soft sensor as been recently developed using a 3D cellular automata-based model to track ore size throughout the pile, and estimating the live capacity and size at each stockpile feeder to the primary mills. Finally, a hydrocyclone soft sensor is being developed to monitor performance using available hydrocyclone models to estimate the size and flow balance around the cyclone in real time. The model-based soft-sensor approach aims to synthesise and analyse existing data and provide operators and engineers with process- and model-relevant information that can facilitate making better process decisions. Maintenance data has proven useful for model development as it allows soft sensors to automatically adjust and compensate for the effect of progressive wear, for example for mill liners, thus helping the models to maintain calibration throughout the equipment life.

Aug 24, 2022

By M Scoble, W S. Dunbar

This paper reviews methods for grade estimation in short-term mine planning for block caving. Two particular tools are used: Ordinary Kriging and Simple Kriging with moving averages. It is also considered the influence of draw characteristics on the grade estimation process. Reference is made to mine case study data and analysis. These demonstrate that operational grade estimation is not a trivial process. It must take into consideration: the grade variability (in terms of ore and dilution), sampling interval, geological and geotechnical characteristics, geometrical layout and draw characteristics. Significant improvements appear possible in short-term planning if variogram analysis, as well as kriging methodologies, are introduced into the operational grade estimation process.

Jan 1, 2000

By K G. van den Boogaart, S Konsulke, R Tolosana Delgado

Adaptive mineral processing has to rely on spatially predicted information on primary geometallurgical parameters, like phase composition, size and shape distributions of grains from various phases, portions of value elements in different grain types. Naively, one would predict these parameters geostatistically and select an optimal processing for the predicted structure. This is suboptimal, due to various kinds of non-linearities in the problem. First, some primary geometallurgical quantities themselves are measured in non-real scales, like compositional or stereologically distorted geometric information. Standard geostatistics has to be replaced by compositional and geometric geostatistics, involving complex transforms and restrictions. Further, only partial and uncertain information is available, introducing a stochastic character to the optimisation problem. Moreover, many response variables leading to costs, outcomes and eventual effects of later processing depend non-linearly on the primary geometallurgical parameters, which implies that the final monetary value is not estimated unbiasedly by kriging. Finally unbiased linear prediction (such as kriging) is not the best method of prediction for decision making. The conditional expectation of the monetary values is needed instead. The impact of these problems is explained in this paper, with simplified examples, and a first approach to a general solution is proposed. CITATION:van den Boogaart, K G, Konsulke, S and Tolosana Delgado, R, 2013. Non-linear geostatistics for geometallurgical optimisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 253-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

Although mining, particularly of gold and coal, played a significant role in the development of New Zealand, from the time of the spectacular gold rushes of the 1860s its economic importance to the country as a whole has decreased substantially since that time. Gold, coal and non-metallic agricultural and industrial minerals have been found in economically significant quantities, however, the search for base metals has not been successful.

Jan 1, 1982

By Faidel VV, Yushina TI, Yagodkina NG, Yatsimirsky AK, Chanturiya VA

Among the problems of the flotation of sulphides by the thiol collectors is the dependence and varieties of the flotation starting with the time and oxygen contents in the slurry. For sulphides, the flotation stage follows after the electrocatalytic oxidation of the collector with oxygen on the surface of the conductor minerals. The necessity of the oxygen for sulphide flotation (Plaksin and Bessonov, 1957) is in accordance with a corrosion model of a collector surface sorption (Salamy and Nixon, 1954). As Golikov and Nagimyak (1961) showed, the sulphides possess catalytic activity which provides the autoxidation of the xanthates in the sluny to the dixanthogen. This stage can be rather protracted, which limits the speed of the total process. Disulphides constitute important collectors for the sulphide flotation and the optimal degree of the xanthate oxidation is about 20 per cent for different ores (Abramov, 1978) or, following Chanturiya and Nazarova (1977) the surface compositions for various sulphide ores are different and an optimal oxidation degree is variable from five to 25 per cent according to the ore nature. The optimisation of the surface composition is possible by application of the dixanthogens, or by a partial chemical, electrochemical, or catalytic oxidation of xanthates (Desains, 1847; Schall, 1896; Vigdergauz, 1989). According to Rand (1977) and Vigdergauz (1991) sulphides possess different catalytic activities for oxygen electroreduction. In neutral solutions, for example, the following decrease in the order: FeS2 (Fe,Ni)9S8 CuFeS2 FeS; Cu5FeS4 Cu2S; PbS (Vigdergauz, 1991). For the cases of low catalytic activities of the sulphides, the preflotation oxidation of xanthate could be useful to optimise the process kinetics.

Jan 1, 1993

By F Saloojee, F K. Crundwell

Refractory ores need to be pretreated prior to cyanide leaching for acceptable gold recovery. Pressure oxidation is one method of rendering the ores more suitable for cyanidation. The focus of this work is optimisation of autoclave configuration for pressure oxidation. An autoclave for the pressure oxidation of a feed containing pyrite and arsenopyrite was modelled, using the population balance framework. The autoclave model takes into account feed particle size, reaction kinetics and retention time. Mass balance calculations were incorporated into Cycad Process« software. This allowed for the investigation of different circuit configurations. The base case model consists of a single autoclave. The feed was then doubled and additional autoclaves were added to provide the same residence time as the base case. Four different configurations for the additional equipment were simulated. These were parallel, series, series with inter-stage thickening and parallel-series circuits. The options are compared in terms of extraction and productivity. The parallel circuit behaves similarly to the base case. The series and series-parallel circuits have higher recoveries and productivities than the base case. The series circuit with inter-stage thickening provides the highest extraction and productivity. This is because the thickening reduces the slurry volume and increases the residence time of the solids in the downstream autoclave.CITATION:Saloojee, F and Crundwell, F K, 2013. Optimisation of circuits for gold pressure oxidation, in Proceedings World Gold 2013 , pp 181-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Vestre J, Kure K, Bergqvist I

Existing practical laboratory tests for comparative strength determination of commercial explosives consist of the lead block test, the ballistic mortar test, the bubble test etc. These tests are carried out in material with quite different properties compared to rock. The theoretical performance potentials of commercial explosives are traditionally described by weight-strength (WS). Some explosive producers use the Langefors formula for weight-strength calculation, where also the gas volume is considered. Neither the theoretical nor the practical methods for determination of explosive performance such as the above, give good enough prediction of fragmentation and heave in rock blasting. For these reasons a project was started for the purpose of finding a small scale test method which predicts how different explosive parameters affect fragmentation and heave. Small scale tests were carried out by using 50 cm cubical blocks, mainly of concrete, but a few also of rock. All blocks were blasted in a steel cylinder with a diameter of 1.2 meters. The velocity of detonation was monitored, and the velocity of fragments was derived from their time of arrival at the steel wall, which was registered by accelerometers. After blasting all fragments were screened. The charge diameter was 22 mm and the amount of explosive 78 grammes, resulting in a specific charge of 0.62 kg/m3. Explosive properties such as energy, gas, VOD and density were systematically changed.The results presented in this paper show how fragmentation and heave systematically change when the explosive properties like energy, gas, VOD and density are systematically changed. The results from the small scale tests are compared to full scale tests carried out in tunnel blasting, and during summer 1990 also in bench blasting.

Jan 1, 1990

By M Scoble

This paper is based upon the experiences of collaborating academics in two mining schools and their personal view of attempts to integrate the principles of sustainable development into mining education and research. In this quest, the concept of sustainable mining practices is proposed, not only relating to environmental, social and economic performance but also stressing mine safety and efficiency. These practices need to support strategies that enable flexibility and resilience within mine operations to counter recessionary cycles. Also, these counter-cyclical strategies are now imperative for sustaining mining education and research itself. There is a critical interdependence between these two different perspectives on æsustainabilityÆ. The paper concludes by demonstrating models of strategies that promote inter-disciplinarity, collaboration and networking for sustaining mining schools.

Jan 1, 2009

By B Washington, A Campbell, R Taylor

A sampling and measurement program was undertaken on the reaction shaft of the Olympic Dam copper flash smelting furnace. The object of the work was to provide information to validate a mathematical model of the burner and reaction shaft. Samples and measurements were undertaken through the burner inspection ports and the South East (SE) shaft sampling port about half way down the reaction shaft. Samples were collected to enable the calculation of particle loading of shaft gases, or sizing and chemical analysis of the partly-combusted feed, and the preparation of polished sections. Measurements were made of the temperature and sulfur dioxide content of the atmosphere, as well as plume velocity.To implement the program it was necessary to design and construct the following specialised items of equipment. For use at the burner inspection ports: a cup sampler for obtaining samples below the burners (temperature, solids loading and samples for characterisation).For use at the SE shaft sampling port and also at the settler level: trough sampler (plume definition and samples), isokinetic sampler (used as a velocity probe in this work), temperature probe (temperature traverses across the shaft), and sulfur dioxide probe (SO2 measurements across the shaft).The design of the sampling and measuring equipment is described, and examples are cited of the types of information obtained. The problems arising from working in a hot environment with molten or sticky particles are discussed.

Jan 1, 2005

By Mernagh T, Large R. R, Ryan C. G, Huston D. L

The Tennant Creek goldfield is one of the largest gold producing districts in Australia, and major deposits, including Gecko, Juno, Orlando, Peko, Warrego, Nobles Nob, Golden Forty, Argo, TC 8 and White Devil have produced more than four million ounces of gold over the past two decades. Gold-copper-bismuth mineralisation at Tennant Creek occurs in lenticular, ellipsoidal or pipe-like bodies of magnetite-hematite ironstones which are hosted in turbiditic sedimentary rocks of Proterozoic age (Large, 1975; Wedekind, Large and Williams, 1989; Le Messurier, Williams and Blake, 1990; Morrison, Donnellan and Hussey, 1992).

Jan 1, 1994

By J Burgess, G Scanlan

In 1993 after over 110 years of mining operations, production ceased at the Broken Hill North Mine. Following the cessation of operations a rehabilitation program was developed to satisfy the requirements of the various government departments. This program has been implemented progressively since mine closure. The paper will discuss: primary aims and objectives of the rehabilitation program, implementation of the program, rationale behind rehabilitation objectives, and problems encountered in implementation of the program. To-date the primary rehabilitation of the mine has involved the capping of redundant tailing dams with inert waste rock to prevent the contamination of the receiving environment. A Water Management Plan has been developed to contain all run-off from the mine area in an extreme storm event. A cultural heritage assessment of the leases has been undertaken to ensure the rehabilitation is consistent with the historical significance of the site and community expectations. All redundant material from the mine has been sold in a æno reserveÆ auction and the workshop area has been relocated to the Southern operations. At present the only active areas on the mine are a maintenance area for equipment for the Potosi open pit, and a primary crusher for Potosi ore which is railed to the Southern operations for further processing. Upon completion of the rehabilitation program, Pasminco Broken Hill Mine intends to relinquish the mining leases to the Department of Mineral Resources.

Jan 1, 1998