Search Documents

By D Cliff

"Recent underground coal mine incidents have again raised the issue of: under what circumstanceis it safe for personnel to re-enter the mine? Mine rescue guidelines make recommendations aboutthe limits in terms of the circumstances, lives at risk, no lives at risk and training exercises. Theseare based upon percentages of the upper and lower explosive limits. Many factors infl uencesett ing limits for safe re-entry. These include: the representativeness of the sampling location(s),the rapidity of gett ing an underground sample analysed and the rate of change of the atmospherebeing monitored. Value judgements based upon these parameters will then infl uence the sett ing ofa trigger point based upon per cent explosibility. This raises the question of how the percentage ofthe lower or upper explosive limit is established. It is easy to defi ne this when the sampling pointdata sit on the fresh air limit line. However - what value is used when the sample sits somewherein the body of an explosibility diagram? This paper explores the various options and illustratesvarious pitfalls and problems that are faced in making such a determination. These include howthe data are represented and the assumed knowledge of those doing the interpretation."

Jun 1, 2012

By P Aguilera, C Guerrero, M Tucker

With the advent of Electronic Detonator Systems in the global mining industry, as well as the development of high precision pyrotechnic delays, the measurement and analysis of delay performance (usually measured in terms of dispersion about a batch mean û precision, and the deviation of that mean from the nominal detonation time û accuracy), has become an important issue. Through the non-conventional use of existing Velocity of Detonation (VoD) measurement technology, it has been shown to be feasible to measure the precision and accuracy of delay detonator series connected in the same manner as a typical open pit bench hook up. This paper describes the work undertaken to compare and contrast performance results obtained using a range of instrumentation including High Speed Video (HSV) filming, digital counter timing using a Hewlett Packard Universal Counter and a digital VoD measurement device. The results obtained demonstrated the practical feasibility of using the latter technology in order to obtain relatively large amounts of data in a time-efficient manner, with a precision of better than 0.5 microseconds, if required. The results also confirmed the close statistical agreement obtained between the three forms of performance measurement, therefore permitting the substitution of the VoD measurement technique for the more capital cost intensive HSV technique and the slow, sample-by-sample HP Universal Counter method. This paper describes the methodology applied and the results obtained.

Jan 1, 2004

By D McCoy

Titanium feedstocks are the building blocks of the titanium value chain. They can be mined directly, as is the case for ilmenite, leucoxene and rutile, or manufactured from ilmenite by extracting various quantities of non-TiO2 components from the ore by chemical and/or thermal processes.While feedstocks can be grouped into categories of materials with similar characteristics, they are essentially unique products from very different mining locations around the world. In fact, no two feedstocks are exactly the same. As such, the variations between the available feedstocks, in combination with the permutations in processing technologies to turn the feedstocks into titanium pigment or metal, mean that choices between feedstocks are specific to the location in which they are utilised.In this paper, the authors examine the key requirements of titanium feedstocks to the TiO2 pigment and metal sectors. Apart from the well known differences between feedstock choices for the sulfate and chloride process, the more opaque considerations in feedstock sourcing are examined.

Oct 5, 2011

By J Player, G Sweby, S Webber, E Jones

Seismic systems are a tool for the monitoring and forecasting the rock mass response to excavation. Common issues encountered at mine site audits and reviews are: how to design an effective seismic system, implementation of the design, interpretation of seismic source results and understanding the reliability of the seismic source. These issues are often a function of several items including: • Experience of site personnel in undertaking seismic system design. • Personnel not envisioning multiple phases of system expansion to understand system robustness issues. • System design/expansion occurring in response to damaging seismic activity rather than planned expansion of a system • The mine access development is often localised in comparison to the total orebody being mined hence, planning sensors in longholes in advance of development rather than in short holes close to development will improve the three-dimensional aspect of the network. • Limited site processing of the seismic event data, hence engineers do not see the uncertainty associated with event location, size, source and system layout. Mine site users require a framework to appreciate the challenges and limitations in locating large events. For example, event locations are given as precise measurements (to the nearest centimetre) whereas the volume of deformation resulting in the event often has dimensions of tens of metres or more (as defined by the source radius). A stronger awareness of the uncertainty of rock mass yield within large seismic sources will assist site users in the interpretation of rock mass damage. The encountered design and implementation errors are reviewed and discussed with a practical set of rules presented to provide a robust seismic system that provides consistent results and increases the user’s understanding of uncertainty in source location and size. The authors’ experience across multiple mine sites, seismic systems and damaging seismic events over a 30 year period has been summarised into practical rules for site personnel of all experience levels.

Nov 29, 2022

By D Shuen, R Sales, D La Rosa

Semi-autogenous grinding (SAG) mill control is complex and depends on many dynamic process variables. Good control strategies ensure that a mill is operating as close to optimal as possible, resulting in significant economic benefits to an operation. Pueblo Viejo, a gold mine in the Dominican Republic, has been actively improving their control strategies since start-up in 2012, and one of these initiatives was to install an acoustic monitoring system on the SAG mill. The data from the system is used to optimise the mill’s performance by limiting the time the mill is either running too quiet or too loud. The lower limit is an indication that the charge in the mill is too high for efficient breakage or that the mill speed is too low and grinding media are not striking the toe of the charge. Conversely, when the acoustic emissions from the mill are too high, this can indicate that the balls are striking above the toe of the charge, resulting in inefficient grinding and excessive liner and lifter wear. Adjusting mill operating conditions to keep acoustic emissions in the ‘sweet spot’ between these limits results in more efficient grinding.Pueblo Viejo installed a Metso SmartEar™ to monitor the acoustic emissions of their SAG mill in January 2013. This system has been installed on many mills around the world and is specifically designed for optimising SAG mill control. One system output is the impact counter which measures steel-on-steel impacts on the mill shell. The impact counter uses both frequency and time domain analysis to approximate the number of ball impacts per minute. This method of analysis excludes parts of the sound signal not associated with steel-on-steel impacts and gives an accurate measure of this critical control parameter. After the acoustic system was installed, Pueblo Viejo collected data to determine the upper and lower limits for the impact count variable. The live data is available to the mill operators and it is used as one of the key operating variables to control the mill.Through continuous improvement and the use of advanced technologies like SmartEar™, Pueblo Viejo are improving the control and operation of their SAG mill, resulting in reduced liner wear, more efficient mill performance and optimised energy consumption. This paper discusses the installation of the system, and the measureable benefits obtained by using acoustic monitoring to control their SAG mill.CITATION:Shuen, D, Sales, R, Wortley, M and La Rosa, D, 2014. The benefits of using SmartEar™at Pueblo Viejo, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By A Hosseinzadeh Barforoosh, A Abedi, M Taji

The effect of blast loads on beams is one of the main issues in the analysis of steel structure. In this study, experimental tests on steel beam under blast loading, and also numerical simulation by the Autodyn software to analyse these structures, is discussed. Experiments on steel beam size of 12 by Emulite4 explosive with 30 mm diameter and cortex is done. The patterns of cutting and bending generated in the two tests (empirical and simulation) show a good match.CITATION:Taji, M, Hosseinzadeh Barforoosh, A and Abedi, A, 2015. Comparison of experiment and simulation of blast loading on the steel beam, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 161–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Ravn

Under platform exhaust (UPE) systems are often designed into metro stations as a means of removing heat generated by trains as they come to a halt in the platform. These systems are designed to extract heat from the brakes and brake resistors directly at the source in order to capture as much heat as possible before it can enter the public areas of the station, or contribute to the temperature build-up in the tunnels. Due to space requirements for the associated duct and air handling units, the UPE plays a significant role in the geometric design of the platform and station as a whole.In recent years questions have arisen as to the effectiveness of UPE systems. However, very little data is available for designers to use when making important decisions on the station designs for new metro systems. This is important as significant savings could be achieved by omitting or re-designing these systems for new build stations; not only due to the capital costs of space provision for the duct itself but also due to the associated operation and maintenance cost of the UPE system.This paper will present recent measurements of the UPE system of the Copenhagen metro together with one-dimensional (1D) simulations, looking at typical dispersion of heat into the station plenum box and air exchange through draught relief shafts as the train enters the station in order to evaluate the effectiveness of the UPE system. The aim of this paper is to disseminate the results of measurements and analysis to increase awareness of the issue and to provide discussion relevant to designers in their evaluation of heat removal systems in new build station designs.

Mar 8, 2011

By F Wu, H Wang, W Chen

A pressurisation method with multiparallel fans has been adopted at HongLiuLin Coalmine to control the significant external air leakage through the goaf area of coalface 15207. Potential damaging effects of large external air leakage on a coalmine’s ventilation system are analysed according to the current air leakage status caused by the exploitation of shallow-covered coal seams. The use of pressure balanced ventilation to prevent external air leakage through goaf areas is introduced. The calculation of ventilation network of HongLiuLin Coalmine shows that the air resistance of an external air leakage branch through a goaf area and the air pressure drops from the intake slope to the working face can be adopted to determine the values of pressure to be increased by regulating fans and airflow controlling parameters of regulators. By investigating airflow requirements of the pressure-balanced area as well as the performances of the auxiliary fans currently used in the coalmine, the number of pressurisation fans needed is fixed. The expected result is achieved after the pressurisation method has been carried out, which can be helpful for other coalmines to handle similar problems.CITATION:Wu, F, Chen, W and Wang, H, 2015. Multiparallel fan method to prevent significant external air leakages through a goaf area of a shallow covered coalmine, in Proceedings The Australian Mine Ventilation Conference, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Stevak D, Plesingerova B, Ellias K, Tkacova K

This paper presents information on the processing of minerals by decrepitation that can be an integral part of their mineral dressing. In the case of carbonates, processing by decrepitation is a special operation that has its objective as concentration of the oxide. Selective fragmentation of magnesite brought about by decrepitation uses pseudomorphosis which was observed at thermal decomposition of carbonates. By decrepitation of magnesite high-grade MgO concentrates were obtained with MgO contents above 80 per cent. With the sideritic ores a very important phenomenon was observed consisting in the removal of quartz in the fragmented fine-grained product which favourably affect pelletisation of the fines. The selective concentration of the MgO product brought about by thermal decomposition of dolomite accompanied with decrepitation was negligible.

Jan 1, 1993

By B J. Monaghan, R J. Longbottom, S Prabowo, D Del Puerto, B Maisuria, C W. Bumby

The use of hydrogen as a reducing agent can substantially reduce carbon dioxide (CO2) emissions from the ironmaking process. Iron ore fines can be reduced in a fluidised bed (FB) using hydrogen (H2) at high temperatures (>800°C), although several studies have reported the sticking of particles which causes the bed to defluidise, effectively shutting down the process. Here, we report results from the reduction of New Zealand (NZ) titanomagnetite (TTM) ironsands in a small-scale laboratory FB (100 g) at temperatures between 800–1000°C using H2 flow rates up to 5 standard L/min. No sticking phenomena are observed under any of these conditions, which is attributed to the formation of a stable titanium-bearing oxide layer on each particle’s exterior, preventing iron-iron contact at the particle surfaces. Pre-oxidised NZ TTM ironsands have also been studied and shown not to stick. Interestingly, at lower reaction temperatures the reduction kinetics for pre-oxidised ironsands is faster than for as-received ironsands. This increased kinetic rate can be attributed to the preoxidation stage inducing micro-fractures that create a void for the hydrogen to diffuse into the inner regions of the particle. In addition, oxidation of TTM appears to segregate the particle into two distinct phases, a high Aluminium-Magnesium (Al-Mg) phase and a high Titanium (Ti) phase. The findings are important as increasing the operating temperature of the FB reactor results in a faster reaction rate and higher gas utilisation, making the process more economically attractive. Furthermore, oxidation of NZ TTM ironsands results in a faster reduction rate at lower temperatures (800°C– 900°C) opening the opportunity to reduce the reaction temperature which might be beneficial in a final commercial-scale process.

Sep 18, 2023

By J Seccatore, T Marin, M Cardu, G De Tomi, F Galvão, A Rezende, E Melo

Small-scale mining operations are characterised by a large variety of equipment availability and a high level of operational flexibility. Mine planning is usually scarce or absent in small quarries in Brazil, and mine management generally focuses on daily operations. As a result, analysis of the effects of unit operations, such as blasting, over the whole mining process is often neglected. The goal of the following project was to study the effect of production blasting on loading and hauling times, secondary breaking times and primary crushing times at the Experimental Mine of the Research Center for Responsible Mining of the University of São Paulo, Brazil. The operations analysed included blasts that performed:under the average operational standard, defined in this paper as Case 1according to quarry standards, defined in this paper as Case 2.In order to establish the effects of blasting on the downstream process, three key performance indictors were used:The time taken to load the truck, when there is the need for material selection. Due to the fact that we do not have an operational baseline, the increase in time cannot be established, meaning that we must content ourselves with comparing the mean time in each scenario.The average time used for secondary breaking machinery.The time required for the primary crusher to fully process the load of a single truck. The results obtained indicate correlations between the coarseness of the blasted material and these operational times. Solutions are suggested and evaluated for the improvement of the small-scale mining process.CITATION:Marin, T, Melo, E, Seccatore, J, Cardu, M, Galvão, F, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The effect of drilling and blasting performance on fragmentation in a quarry and time for loading, secondary breakage and crushing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 355–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Coveney, A Rich, D Grimsey, J Wood, S Creedy

In 2021, BHP and Metso examined processing of high-MgO nickel sulfide concentrates using Metso’s Ausmelt Top-Submerged-Lance (TSL) technology. Test work was conducted in Metso’s pilot test work facility in Dandenong, Australia to explore operability of the SiO2-FeO-MgO-CaO-NiO slag system across a wide range of compositions, temperatures and bath oxygen potentials. Pilot-scale testing aimed to define slag ‘operability limits’, representing the lowest bath temperature at which stable process and equipment operation could be maintained. This work was supported by FactSage™, version 8.2 (by Thermfact/CRCT and GTT-Technologies) thermodynamic modelling, slag viscosity measurements, physical characterisation of quenched slag samples performed by the University of Queensland and benchmarking of commercial-scale TSL nickel smelting operations. A wide range of slag compositions were examined, with Fe/SiO2 ratios varying from 0.4–1.1, CaO content from 0.8–7.0 wt per cent and MgO content from 6–19 wt per cent. Slag SiO2/MgO ratio, wt per cent CaO and matte grade were found to have the greatest impacts on identified operability limits. Operability limits were found to be influenced by both the solids content in slag and viscosity of the remaining liquid slag phase, with the relative contribution of these parameters heavily influenced by the slag composition. In the majority of trials, limits were defined by a theoretical solids content of 40–50 per cent, however in trials with a low Fe/SiO2 ratio and/or low wt per cent CaO, limits were characterised by a much lower solids content due to the increased effect of the liquid slag viscosity in determining the behaviour of these slags. The test work highlighted inherent flexibility of the Ausmelt TSL process to operate across a wide slag range of slag compositions and recover from process disturbances without an interruption to feeding. The trials also demonstrated the possibility for Ausmelt TSL technology to process concentrates with an Fe/MgO ratio as low as 1.4, which has important implications to the commercial-scale processing of high MgO feeds. Arsenic rejection across the trials was very good, with only 30 per cent of arsenic in the feed inputs reporting to the matte phase. Such high levels of arsenic removal provide the Ausmelt TSL process with a notable advantage over alternative smelting technologies.

Aug 21, 2024

By C K. McKenzie

As more and more mining operations around the world either switch to, or trial, electronic initiation systems, the breadth of knowledge and experience regarding their effective application has widened considerably.In South America, for example, there is a strong perception that in order to achieve the finest possible fragmentation, very short electronic delays must be used between successive holes within a row. Limited field studies involving measurement of fragmentation have been conducted to support that paradigm and there are few long term studies which have been strongly supported by measurements of productivity either in the pit, in the plant, or in the leaching pads.On the other hand, some well documented studies have been conducted in North America, showing not only the impact of delay timing on fragmentation but also the effect on semi-autogenous grinding (SAG) mill productivity over extended periods of in excess of 12 months. To date, those studies suggest that optimum timing is considerably longer than the times commonly used in South America.This paper explores the current knowledge of the effects of delay timing on issues ranging from size distribution to vibration impacts in pit walls, to vibration and overpressure impacts in surrounding communities. It also explores how fragmentation modelling can be adapted to reflect fragmentation trends that have been reported in various technical conferences around the world.

Nov 8, 2011

By J Loeb, J Dampney, P Cameron

Optimisation of Blast Design and Execution must be done right the first time. It is too late after the ore is broken. Consequences of poor design and execution negatively affect productivity from load and haul through the primary crusher to processing and hence reduce mine site profits. Harnessing and utilising ‘big data’ from geology, geometallurgy, drill hole location, powder loading, blast timing, blast movement and fragmentation to close the loop in blast design and optimise the blast increases productivity across the entire value chain from Mine to Mill. As the internet of things and artificial intelligence increases the quantity of data available, being able to capture and utilise this data to advantage is a challenge. Recent advances in software and hardware together with the increased power of cloud computing allows engineers to close the blasting loop to increase mine site productivity. Numerous case studies over the years detail significant gains from implementing the innovative technologies available to Mine to Mill projects. The opportunity is available for all members of the multi-discipline teams at each mine site to actively ensure productivity improvements are realised and maintained not only in their area, or silo of responsibility but across the entire mine site. This paper refers to recent case studies which outline how significant improvements in productivity are available to all mining operations to increase mine site profitability and dividends to shareholders.

Jun 22, 2022

By C Linklater, A Garvie, D Kentwell

Various Australian and international regulatory bodies (Environmental Protection Authority, 2015) require an early assessment of the geochemistry of waste rock. This usually includes estimates of the locations and volumes of potentially acid forming (PAF) materials and requires sampling of the waste rock zones as well as submitting the samples for a series of tests. We know that the required number of samples will vary depending on rock type, mean sulfur levels and spatial variability of sulfur as well as total volume. The key question is how do we know when we have enough samples?This extended abstract describes the application of geostatistical methods to examine how sample numbers and sample locations influence the preliminary conclusions that may be drawn for early stage waste characterisation.CITATION:Kentwell, D, Garvie, A and Linklater, C, 2016. Geostatistics and sample numbers from an acid and metalliferous drainage perspective, in Proceedings Life-of-Mine 2016 Conference , pp 12–15 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By I M. Platten, Y Xie, B W. Cuffley, S C. Dominy

"Geometallurgical programs require the collection of representative samples for geochemical, mineralogical and metallurgical test work. Such protocols must be designed to suit the style of orebody in question. The distribution, proportion and size of gold particles have a direct impact on the effectiveness of sampling and test work protocols, and the gold recovery processes employed. Characterisation studies focusing on ore mineralogy, and gold particle deportment, size and distribution are required. High resolution X-ray computed tomography provides a non-destructive method for analysing the 3D nature of gold in rock samples. It can be used to calculate the modal abundance, particle size and distribution of gold in the sample volume. This paper presents a case study of the imaging of in situ gold particles in a high-grade gold ore. The Nick O’Time reef system comprises laminated quartz veins, which locally bear extreme grades of up to 100 oz/t gold. The mineralisation has previously been characterised from both a mineralogical and metallurgical perspective. Eight visible gold-bearing vein samples were scanned using X-ray microtomography. Microtomographic data were integrated with previous mineralogical and metallurgical test work outputs.CITATION:Dominy, S C, Platten, I M, Xie, Y, Cuffley, B W and O’Connor, L, 2016. Characterisation of Gold Ore from the Nick O’Time Shoot (Tarnagulla, Australia) Using High Resolution X-ray Computed Tomography, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 241–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By O Dominguez

Mine value chain reconciliation (MVC) is a necessary procedure to evaluate a mine’s performance against the assumptions and models used to plan mining and processing operations. Using nomenclature from Parker (2012), F2 reconciliation is the ratio between material received at the mill, compared with material sent to the mill, commonly reported in terms of tonnes, grade and metal. Measurements of material sent to the mill can be estimated in many ways, including: fleet management system (FMS) records, truck counts, or volume reduction. Most time-based reconciliations (for example, month-end reconciliation) use short-term model depletions of in situ rock measured by periodic topographic scans or surveys.

Mar 22, 2022

By R Durchholz, A-J Heiertz, R Schmitz

Mining of lignite is the largest bulk materials handling activity in Europe. In order to mine this lignite, with an average calorific value of only a third of bituminous coal in an economical way, highly efficient opencast mining technology is mandatory. The total continuous mining of overburden and lignite was introduced more than 60 years ago and was subsequently developed stepwise into the largest mass transport system of the world. In 2011, the Inden Mine, one of three RWE Power mines, stripped 90 Mbcm of overburden to produce 22 Mt of lignite. In total, nearly 100 Mt of Lignite was produced from the three mines of RWE Power in Germany. Beside bucket wheel excavators (BWE), several high-performance in-pit crushing and conveying (IPCC) systems, which allow the adoption of continuous mining systems, even for typical shovel and truck (S&T) operations, are available today. RWE Power assists operators considering a change from the S&T to IPCC technology, both in the planning process involving large-scale belt conveyor systems and later with operational know how transfer. In a number of cases, the challenges associated with this system change have been addressed and solved successfully. One key challenge is managing the development of skills for operating the belt conveyor systems efficiently. This paper compares the effectiveness of S&T to different configurations of continuous mining operation for an up to 170 m deep mine with a total annual output of 117 Mbcm. From the mine operatorÆs point-of-view, the quantity and skill level of staffing required for operation and maintenance are discussed in detail. The main conclusion of this paper is the larger the operation becomes and the longer the mine life is, the earlier fully continuous mining systems should be planned and implemented.CITATION:Schmitz, R, Durchholz, R and Heiertz, A-J, 2012. Change challenges for large open pit mines, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 103-110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

Longhole open stoping was introduced in the zinc-rich 'B' lode at New Broken Hill Consolidated Limited (NBHC) during 1968. Since then one longitud- inal and a series of transverse longhole open stopes have been developed. The longholes are drilled using Gardner Denver airtrac drilling jumbos and the broken ore is loaded from drawpoints and transported to chutes using Wagner ST5 scoop- trams. The holes were drilled from sill stopes 160 ft apart. The width of an emptied transverse longhole stope was successfully widened by blasting rings of blastholes drilled parallel to the stope wall. Proposed stope and pillar designs for a series of transverse longhole open stopes were assessed using a method of finite element analysis, applied to a longitudinal section through the area. Blastholes have been surveyed for dip and bearing using an Eastman borehole survey camera. The data produced has provided the basis of a study of blast- hole deviation. Deviation of boreholes is considered to be the major cause of the formation of benches in longhole stopes.

Jan 1, 1971