Search Documents

By C A. Cooper, G A. Suter

The sizing of a starter dam for a Tailings Storage Facility (TSF) involves balancing many competing demands. It should cost as little as possible, be high enough to store tailings until the first raise can be constructed, it must be able to contain water safely, and it must be designed in such a way that the long-term integrity of the higher raises are not compromised, among other things. In addition to these demands there is the complication of the behaviour of the process plant, and the tailings during commissioning. Variations in slurry density, excess water in the TSF, initial settled density of the tailings, reliability issues, and beach slopes above and below water can all impact the way the tailings beaches are developed and ultimately impact the ability of the starter dyke to contain the required volume of tailings and water.The conventional approach to the design of a TSF starter dyke is to begin looking at the elevation required for a set of deterministic design parameters, find ways to reduce the size or volume of it as much as possible to reduce cost, and then possibly look at the sensitivity of some of the input parameters. This paper discusses a stochastic modelling approach for starter dykes that allows a wide range of design inputs to be simulated quickly, with an envelope of possible results produced. The sensitivity to different parameters can also be examined to understand which design inputs have the biggest impact on the required dyke sizing. By integrating the 3D TSF modelling tool Muk3D with GoldSim, it will be demonstrated how a wide range of scenarios can be evaluated and how that information can be used to make better decisions about the selection of design options.CITATION:Cooper, C A and Suter, G A, 2018. Starter dyke optimisation with Muk3D and GoldSim, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 466–475 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Harding, S Munro, R A. Bearman

Despite the importance of the primary crushing stage, performance optimisation is not well analysed with sufficient focus to give improvement opportunities. At the Newcrest owned Telfer operation, liner life plays an important part in scheduling planned maintenance. Major consideration is given to monitoring crusher performance, as the highly abrasive nature of the feed significantly impacts the liner wear life. A study was undertaken by the lead author which focused on establishing a strong baseline of accurate data pertaining to the performance of the crusher, in terms of, operating parameters, liner life and key machine design factors. As part of the study, mining feed materials were examined for a particular set of liners and this revealed that improved methods should be pursued. Due to the competitive nature of the mining industry, the business solution to complex problems with long shutdown cycles should be streamlined to incorporate a non-operational modelling approach that is significantly more efficient than traditional online trial and error methods. In order to dramatically reduce the time and business risks, it was decided to engage services to model and simulate the liner life by varying main operational and mechanical factors. The key to all simulation work is gathering high quality baseline data. Such data allowed deployment of the Kinematic Crusher Model and validation of the model against worn 2D wear liner profiles. The proven model was then successfully deployed to predict operational values that defined crusher performance. To enhance the study, further investigation into a set of mechanical and operational simulations generated a sensitivity matrix measuring key performance parameters throughout the wear life of the liners. The study revealed throughput as a highly sensitive parameter and a change in eccentric throw provided the greatest improvement in extending liner wear life.

Aug 24, 2022

The Kalgoorlie Golden Mile is proposed as an Archaean volcanogenic-type deposit, modified and redistributed along later-developed structures. Rich pyritctelluride and Green Leader gold mineralization is associated with the end phase of basic volcanism and, in a general sense, is confined to a broad interface zone between the products of marine basic volcanism and later acid volcanism. There is virtualIy no ore associated with the main body of acid volcanics.Green Leader is the local name of a type of ore that occurs at some igneous rock contacts in association with graphitic sediments and layered acidic tuffs. It is characteristicalIy green, of various shades, and commonly yields very high gold assays, the reasons for which are not apparent in hand specimen.Carbonates, carbonaceous shales, tuffites, rich gold ores, and acid and intermediate dykes, alI indicating a common heritage, are features common to the main ore hosts, viz. the Paringa Basalt (Calc Schist) and theGolden Mile Dolerite ("Quartz Dolerite Greenstone").Several probably related fracture systems have reconstituted most, but not all, of the original deposits into a large number of steep tabular lodes.Includes two sets of discussions and comments from later Proceedings volumes.

Jan 1, 1974

By J Ledgerwood

Namakwa Sands is a mineral processing company based on the West Coast of South Africa and is solely owned by Exxaro Resources Limited. Mineral ore is mined and processed, concentrated and both chemical and mechanically upgraded before being sent for electrostatic and magnetic separation units. The final high value mineral products report as Zircon, Rutile and Ilmenite.The recovery of non-magnetic material is largely dependent upon a number of factors, including but not limited to dew point, ambient temperature, feed rate, mineral size distribution, specific gravity and mineral content in head feed. One important limiting factor to recovery in typical dry mill operations is the particle size distribution of the feed. Variance in the particle size has catastrophic consequences for recovery. This is the reason for this study. Until recently large variances in non-magnetic production were viewed to be a function of machine operation. This view was later rejected with the feed size distribution determined as the major driver of low recoveries, for Namakwa Sands orebody 50 per cent variance in particle size distribution can be noticed within one day. This is because of the successive mining blending techniques employed.The predicament is that the two modes were so closely placed together that recovery of a single mode is almost impossible without the consequence of greatly reducing recovery. The second mode was found at 125 µm while the first was at 90 µm. Interestingly, for the mentioned feed type a cumulative size distribution of a unimodal feed type is almost exactly the same as for a bimodal size distribution. Thus a plot of cumulative size distribution will show no difference due to the modes being so close together. This is the reason why this phenomenon was not noticed before.The study also found that, using an high tension roll (HTR) or rare earth roll, a fine stream with a single mode at 90 µm versus a coarse stream with a single mode at 150 µm would yield completely different results interms of yields. Larger conductive particles are thrown from the roll while small particles loose charge faster (entrainment). Results in terms of the bimodal size distribution show that even though 25 per cent of the feed type is greater than 150 µm the yields followed a similar pattern to that of the coarse particles rather than that of the majority (75 per cent) fine particles. This confirms what was published by M Ziemski and P N Holtham in 2005 on charge decay rates; they mentioned that particle bed effects played a major role in recovery.

Oct 5, 2011

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

By M Schaffer, T Kewe, N Moffatt

Porgera mine is 95 per cent owned by Barrick Gold Corporation. It is located at an altitude of 2200–2700 m above sea level in the Enga province of Papua New Guinea and produces approximately 460 000 oz per annum with a proven and probable reserve of 6.2 Moz. The refractory ore is ground in a conventional semi-autogenous grinding and ball mill circuit. After the gravity gold is recovered, the slurry is floated, oxidised in the autoclaves and then leached. This paper will focus on the flotation circuit and the recent upgrade of the control system. The five interdependent flotation circuits were challenging for operations to control as they dealt with variable grade, throughput and circulating loads, as well as the physical limitations of the equipment. With the installation of 18 Portage Froth Characterization® (PFC) cameras, the plant’s operation has been converted from a level-control based strategy that was focused on individual cells to one that targets grade and recovery control across the entire circuit. Variability in feed and the corresponding launder issues were addressed with a unique site initiative of deflector plates to indicate filling level. Non-linear closed loop control was implemented directly in the DeltaV Distributed Control System (DCS) using Portage Advantage Regulatory Control (PARC) algorithms and optimised with AwaRE advanced controllers. The most noticeable benefits achieved with the upgrade include improved flotation gold recovery, consistent flotation sulfur grade and autoclave performance. Correspondingly, there was a significant drop in boiler diesel fuel usage and launder overflow conditions.CITATION:Kewe, T, Moffatt, N and Schaffer, M, 2014. Porgera flotation circuit upgrade and expert system installation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 345–356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Any Australian who knows of the poverty of the early settlers in the first few years following the arrival of Captain Arthur Phillip with his "first fleet" at Botany Bay must feel proud of the progress that has been made in the 174 years that have elapsed since that momentous occasionGFor all its attractive appearance as reported by Captain Cook and Sir Joseph Banks, the shores of Botany Bay and of Port Jackson proved most ,inhospitable, and the accessible country surrounding them anything but suitable for sustaining the life of the small settlement. It is well known that during the first 15 or 20 years the hardy colonists and un-tfortunate convicts were close to starvation on several occasions and were only saved by the arrival of supply ships, which were dependent on the vagaries of wind and current, and the hazards of the uncharted seas they had to -navigate-.When Australia was little more than a miserable penal settlement, Great Britain was one of the great-powers of the world, and the U,.S.A. was an independent nation with a growing degree of prosperity that even then gave promise of its mighty awakening to become, as it has, a e.olossus of industry and commerce,-and the. leader in living standards of the world to-day.Australia, from such a shaky, and comparatively recent start, has risen to a position in which its living standards rank very high in comparison with those of most of the nations of Europe and America. Exact com-parisons are hard to fix because of the wide variety of factors involved .but the Institute of Pab?Lic Affairs .(Victoria) places Australia fifthin the world, excelled only by the U.S.A., Canada, Sweden and Switzerland. The next best after Australia are the United Kingdom, West Germany and France.How we achieved such a high standard of living is a vast subject for study but some of the economic aspects of our climb from abject poverty to a position of near affluence can readily be identified.

Jan 1, 1962

By T Muzondo, C Prins, D De Vaux, R Schouwstra

The Mogalakwena Platinum Mine in the northern limb of the Bushveld Complex is Anglo American PlatinumÆs only open cast operation exploiting the Platreef. The Platreef, which extends along the basal contact of the Bushveld Complex, is geologically and mineralogically a much more complex orebody than the Merensky and UG-2 reefs. Changes in the footwall and the genesis of the Platreef translate into a number of rock types being present. These rock types vary in hardness and recovery potential and present challenges to metallurgical staff trying to optimise the concentrator. A true understanding of the implications of treating these rock types is required if the maximum value from this orebody is to be obtained.In order to more accurately forecast production and incorporate ore variation in the mine plan and comminution and flotation circuits, a geometallurgical approach to managing the operation has been used and is being further developed.CITATION:Schouwstra, R, De Vaux, D, Muzondo, T and Prins, C, 2013. A geometallurgical approach at Anglo American PlatinumÆs Mogalakwena Operation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 85-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By T C. Westerfield, G, M J. Mankosa

An innovative separator known as the HydroFloat cell has been developed specifically for the upgrading of coarse particles that are difficult to recover using conventional flotation cells. The novel characteristic of this separator is the formation of a hindered teeter-bed of fluidised solids into which small air bubbles are injected. The air bubbles selectively attach to hydrophobic particles and form particle/bubble agglomerates that segregate atop the teeter-bed due to their lower apparent specific gravity. The low-density agglomerates are eventually carried into the product overflow launder by the rising current of teeter water. Hydrophilic particles remain in the teeter-bed and are discharged to underflow as a high solids content tailing. Benefits of this hybrid flotation-density separator include enhanced bubble-particle contacting, increased particle residence time, and very low air demand. Test data indicate that significant improvements in the recovery of coarse particles can be achieved using this innovative technology. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent pilot-scale tests conducted for the phosphate industry.

Jan 1, 2005

By F C. D Michelin

As mines get deeper, the critical underground temperature limits will be exceeded, and an increasing number of mines will need to implement, expand or modify cooling systems. Surface cooling plants have many advantages over underground cooling such as efficient heat rejection, and lower relative capital cost; however the delivery of cooling through long underground distances can result in lost refrigeration capacity before the chilled air reaches the areas it is needed most. Refrigeration plants are therefore often overdesigned in size and capacity to compensate for underground losses.More mines are now utilising real-time monitoring and automated control of ventilation airflow and fan systems to ensure the conditions underground are safe and productive, and power consumption is efficiently managed. There may be significant opportunities to extend ventilation monitoring and control into the refrigeration delivery and control system.Energy reduction is an effective way to reduce costs and CO2 emissions, which is an increasingly important part of corporate governance. More efficient refrigeration control is a further step toward reducing energy consumption. This paper looks at an added step in how real-time monitoring can assist in controlling the output and chilled air delivery of a cooling plant. The requirements, implementation, benefits and challenges will be discussed.

Oct 12, 2022

By A T. Spathis, M L. Lawlor-O’Neill

A methodology for the inversion of a scaled charge weight superposition model to predict peak particle velocity (PPV) has been examined. The inversion involves two steps: first simulated annealing is used to get an initial estimate of the model parameters; and second, these parameters are used as input to a quasi-Newton non-linear optimisation method, used to refine the value of the parameters. The methodology recovers the three required parameters (two charge weight scaling parameters and a time window width) and does this directly from a single production blast for a given point of interest. It has been tested on a synthetic example and recovered the input model parameters successfully in the presence of introduced noise with a coefficient of variation ranging up to ten per cent. Another test used the vibration measurements of three tunnel blasts monitored during the construction of the Citybanan tunnel in Stockholm. In this case, the three model parameters are found from one blast and for a given point of interest, and the PPV at the same point of interest is predicted for the second and third blast fired in the same vicinity as the first blast. The three blasts used different firing sequences. The predicted PPV limits use a confidence interval determined from the scatter in the peak levels obtained from the single calibration blast. The methodology was able to predict an upper bound for the PPV in 21 of the 26 tunnel blast vibrations studied. These predictions improve on a previous study involving the same model but which did not use the inversion process above. Given this reasonable success, further testing of the method on other data sets and alternative forward prediction models is recommended.CITATION:Lawlor-O’Neill, M L and Spathis, A T, 2015. An inversion method for the prediction of peak particle velocity in blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 97–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Hill KC, Foster DA

Methods for ore reserve estimation are classified. The amount of information needed to asses ore reserves is analysed. Reference is made to gold sampling. Consideration is given to nugget effects and ore reserve estimation procedures where they are significant. Computer methods are discussed

Jan 1, 1997

By S Hapugoda, J R. Manuel, M J. Peterson, A Poliakov, E Donskoi

The occurrence and deportment of manganese in a number of ferromanganese and Mn-bearing iron ore samples from supergene-upgraded deposits, as well as from magnetite banded iron formation (BIF) and magnetite skarn deposits, was characterised in order to provide a basis for improved understanding of the processing characteristics of different ore types and investigate the potential for development of a robust geometallurgical classification for Mn-oxide ores. An understanding of the Mn mineralogy in mixed Fe-Mn deposits is necessary to inform any attempt to separate the Fe and Mn during beneficiation and to understand and predict the behaviour of lump and fine ore products during processing.A suite of analytical techniques was utilised, including hand sorting of lump ore particles, optical microscopy, X-ray fluorescence (XRF)/inductively-coupled plasma mass spectrometry (ICP-MS) chemistry, X-ray diffraction (XRD), scanning electron microscopy (SEM)/electron probe microanalysis (EPMA) and gas and solid phase pycnometry, in order to elucidate manganese mineralogy, mineral chemistry and mineral textures. Manganomelane group minerals (eg cryptomelane, hollandite), pyrolusite and lithiophorite were the most common manganese oxides in the samples examined. From the microprobe work, there was evidence of probable substitution of Mn, as well as Al and Si, into the structures of goethite and hematite. Manganomelane minerals were often intimately associated with goethite, in particular, and a clarification of this association and the associated Si and Al impurities is fundamental for improved understanding of beneficiation and sintering behaviour of Mn-oxide ores. Due to the poor or very fine crystallinity of some supergene manganese deposits and of some Mn oxide minerals, in particular the extent of overlapping peaks and their variable mineral chemistry, XRD was a problematic technique to equivocally determine Mn mineralogy.For lower-grade, earthy, poorly microcrystalline ores the mineralogical and textural association between mixed Mn, Fe and Al (¦ Si) phases was also critical. The deportment and potential separation of these elements in these deposits, especially Al, was complex, as they were characterised by forms of æhydrousÆ cryptomelane with higher levels of Fe-Al-Si substitution, as well as intimate intergrowths of ochreous-earthy goethite (probably aluminous in part) with cryptomelane, lithiophorite and/or kaolinite.Trace amounts of alkali elements in ferromanganese deposits were considered likely to be preferentially structurally associated with Mn oxides, while lateritic deposits with significant amounts of lithiophorite could contain elevated levels of deleterious impurities; Co and Ni in particular.A combination of solid and gas phase pycnometry proved to be a useful technique for broadly discriminating hematitic, goethitic and mixed Mn oxide-goethite lump particles based upon differences in their envelope and apparent densities. Based upon these preliminary results and ongoing Raman spectroscopy work on manganese deposits sensu stricto, Raman spectroscopy is a technique considered to have promise during targeted research to better link the optical and compositional properties of ferromanganese ore particles. CT-scan (computed tomography scan) analysis could also be combined with Raman spectroscopy and pycnometry to link mineral composition, mineral texture, ore particle textures and particle porosity/permeability to the high-temperature processing behaviour of lump and fines products.CITATION:Peterson, M J, Hapugoda, S, Manuel, J R, Donskoi, E and Poliakov, A, 2013. Textural characterisation of manganese minerals to improve the geometallurgical characterisation of ferromanganese and iron ores, in Proceedings Iron Ore 2013 , pp 281-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M Astorga, J Jackson, J Gaunt

The Ban Houayxai mine (BHX) is a relatively low-grade, low-cost, open pit gold-silver deposit in Laos operated by Phu Bia Mining, a subsidiary of PanAust. The ore production rate at BHX is 4.5 Mt/a, with direct tipping to a semi-autogenous grinding/ball mill circuit with a carbon-in-leach process plant. Approximately 100 000 oz of gold is produced per annum.The operation is located in mountainous terrain with minimal run-of-mine stockpiling. This results in limited capacity for blending from stockpile, with the mill instead reliant upon direct feed ex-pit. Since commissioning in 2012, the plant has seen significant variation in milling rates due to variability in the feed properties of the oxide, transition and primary ores. As part of an ongoing continuous improvement program, an integrated approach was initiated, focusing on maintaining and enhancing production in the future as the proportion of harder primary ore increases. This will specifically focus on direct blending from the loading face using the ore properties and blast fragmentation to maintain mill throughput.This approach was based on the concept of physical assets management, commencing with improving information and knowledge of the condition of the orebody through modelling the characteristics, variability and performance of the feed for processes relevant to throughput. These models are used to support both mine and process plant production planning.The key ore feed characteristics and parameters modelled for the life-of-mine are blastability index, powder factor, crushability or impact resistance and grindability. These predictive spatial models were based on the data from diamond drill holes used in resource definition and geotechnical drilling programs by integrating geotechnical, geological, geochemical and metallurgical data.At the early stages of implementation, the models are being utilised for ore blending decisions to provide guidance and support for budgeting, long-term mine planning, blast design for mill feed and providing the mill with an expectation of performance.CITATION:Jackson, J, Gaunt, J and Astorga, M, 2014. Predicting mill ore feed variability using integrated geotechnical/geometallurgical models, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 165–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By B L. Sainsbury, M F. Lee, A Penney

For most practical rock engineering purposes, stress versus strength conditions around underground openings for which rock masses fail and their various modes of failure, are reasonably well-understood and predictable. Some rock masses and particular rock types fail slowly and relatively quietly. However, others can fail rapidly, violently and maybe with the ejection of significant broken rock. In some countries and in some mines, the latter style of violent fracturing and failure of the rock mass is referred to as ‘strain bursting’. It can be alarming and extremely hazardous to nearby miners and machines. For such situations, the design and installation of appropriate ground support, to provide a safe work place, can be challenging. At any particular mine site, it’s often generally understood which local rock masses (rock types) are prone to strain bursting. Competent and strong siliceous rocks and some massive sulphides are often the main offenders. While some neighbouring, equally-competent and strong rocks might also fail, they do so more quietly and without ejection. To understand this contrast, a better understanding of the fracturing process is required other than simple and standard strength versus stress considerations. Suites of standard intact rock properties from numerous Australian mines have been used to define and help understand different high-stress failure styles for component intact rock; especially those prone to violent fracturing (strain bursting). Simple considerations of micro-fracturing (defects in the intact material), plus the available energy at failure versus the energy consumed during fracturing, distinguishes between over-stressed and competent rock types that fracture violently and those that don’t. CITATION:Lee, M F, Penney, A and Sainsbury, B L, 2018. Proneness of competent over-stressed intact rock to violent fracturing, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 170–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Ibil S

The Gameta Gold Deposit is located on the north-eastern corner of Fergusson Island in the D'Entrecasteaux Islands of Milne Bay Province, PNG, at lat. 9¦ 25' 5, long. 150¦ 47' E or AMG co- ordinate 256740 E/8959000 N (Figure 1). The area is covered by the Fergusson (SC56-05) 1:250,000 scale Topographic Map Sheet and the Koitabu (9079)1:100,000 scale Topographic Map Sheet. The property is held 100% by Union Mining NL (UMG) and lies 105 km NNE of Alotau and 33 km to the ESE of UMGs recently developed Wapolu Gold Mine, a Joint Venture between UMO (51%) and Macmin NL (49%). The inferred resource estimated from surface results and 105 RC drill holes, currently stands at 1.89 million tonnes at 2.6 git gold (1.0 g/t Au cut-off) or 155,000 oz. Evaluation of the property is currently proceeding. To date 111 RC holes have been drilled for a total of 4611 m.

Jan 1, 1997

By B Nielsen, H Lehto, B Musuku

"The demand for fine and ultra-fine grinding associated with the processing of more challenging, finer grained orebodies and the global driver of minimising energy consumption has been an increased focus in our industry. Outotec’s stirred milling technology, the high intensity grinding mill (HIGmill™), was launched in 2012 in response to this industry need. First Quantum Minerals Ltd selected HIGmill™ technology for its Kevitsa mine in Northern Finland. The 700 kW mill is grinding copper rougher concentrate to improve copper/nickel separation and copper recovery. Selection of the HIGmill™ followed mineralogy analysis and laboratory and pilot testing for HIG milling in parallel with flotation tests to determine optimum grind size and energy input.The paper discusses the challenges and successes of the test work, manufacture, installation, commissioning and subsequent operation of the mill. Grinding performance is presented and a comparison between predicted and operating energy efficiency is made. In addition, the various steps to optimise wear rate and minimise maintenance and downtime are made, with particular reference to internal geometry of the mill.Citation:Nielsen, B, Lehto, H and Musuku, B, 2016. Design, Installation, Commissioning and Operation of Fine Grinding Technology at the Kevitsa Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 59–66 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Since the 1950's drilling has been rapidly mechanised. First from hand held drills with air legs to pneumatic jumbos, then to more effective hydraulic jumbos. Development of underground drilling equipment naturally could not have stopped here. Hydraulic drilling saw an improvement in drilling capacity and efficiency after the introduction of second generation drifters in the early 1980's. Also in the early 1980's a few equipment suppliers started to study how to improve the efficiency in operating the rigs. The first computerised rigs for tunnelling were delivered to work sites in mid 1980's. At the same time a few computerised longhole drills started drilling in mines.

Jan 1, 1988

By K Williams, A Lavrinec, V Gurung, D Ilic

The moisture content of iron ore during handling can range from the dust extinction moisture at the point of arrival at the port to the transportable moisture limit at the point of loading ships for maritime transport. Moisture content and ore composition, specifically fines content, have a large influence on ore flowability. Typically, elevated moisture can result in bottlenecks, downtime and lost productivity due to build-up, conveyor carry-back and blockages, increasing maintenance costs. On the other hand, low moisture can result in increased dust emissions influencing the environmental footprint and product losses. Managing the use of water across the supply chain is therefore critical for service life of equipment, productivity, but also has environmental and social impacts, affecting the social license to operate. Previously, experiments have shown that oscillations induced in iron ore during handling and transport can result in movement of moisture through the ore. This kind of moisture migration depends on the nature of these oscillations, such as the undulation of idlers during conveying, the inherent ore properties and the initial moisture content. Moisture has been observed to move either upwards and/or towards the bottom of the burden. These effects can be exploited to remove excess water from the ore influencing handleability and operation, however, the actual mechanisms of moisture migration are currently poorly understood. The study presented herein involves the use of simulation to examine moisture and ore interactions. Simulations using discrete element method (DEM) and coupled with smoothed particle hydrodynamics (SPH) are implemented to investigate the behaviour of moisture in wet ore in the presence of oscillation. This is conducted at a fundamental level first using glass beads and water which is then compared to iron ore at high moisture content. The results of the modelling are discussed in view of experiments conducted.

Sep 18, 2023

By N J. Beukes, S T. Netshio, M O. de Kock

The Thabazimbi iron ore deposit comprises a series of stratabound orebodies, on average 18 - 25 m thick that are aligned along the faulted basal contact between the Penge Iron Formation and dolostones of the Malmani Subgroup, Transvaal Supergroup. Field geological relationships and petrographic observations suggest that the formation of high-grade iron ores took place after contact metamorphism related to the intrusion of the Bushveld Complex (2.06 Ga) but before the deposition of red beds of the Waterberg Group at ca 1.9 Ga. Hard, high-grade iron ores are predominantly composed of martite and microplaty hematite. Goethite is restricted to supergene-modified ores close to the Late Cretaceous û Early Cenozoic Old African land surface. At depth, the high-grade hematite ores interfinger with low-grade dolomite-hematite and calcite-hematite ores. Iron oxides (martite, microplaty hematite) present in these low-grade ores are texturally indistinguishable from those in the associated high-grade ores, ie ore formation is genetically associated with carbonate metasomatism. Microthermometric studies of fluid inclusions in sparitic carbonates and rare megaquartz reveal their hydrothermal origin. Two compositionally distinct aqueous fluids of shallow crustal origin are identified, namely a Ca-Na-rich high-salinity brine (26 wt per cent NaClequivalent, TH ~160¦C), and an aqueous Mg-K-bearing fluid of intermediate salinity (8.3 - 12.6 wt per cent NaClequivalent, TH~120 - 150¦C). The results confirm that high-grade hematite orebodies at the Thabazimbi deposit owe their origin to an event of extensive oxidative carbonate metasomatism (calcification), similar to that recognised at other important high-grade iron ore deposits in the world. Hydrothermal ore formation is both structurally and lithologically controlled. Size and quality of the orebodies was improved by Late Mesozoic-Cenozoic deep lateritic weathering as carbonate-hematite ores were enriched to friable high-grade ores, but this supergene modification is second in importance compared to the primary event of hydrothermal ore formation.

Jan 1, 2005