Search Documents

By J S-L Chan

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Cu-Ag-Au mineralisation at Kluwih prospect in Eastern Java, Indonesia is related to a high-sulfidation hydrothermal system within a volcanic dome (2.35 × 1.7 km diameter). The mineralisation occurs mainly in steeply dipping, structurally-controlled quartz-enargite-pyrite veins (several centimetres to 2 m wide) and is hosted mainly in porphyritic dacite, volcaniclastic rocks and volcanic breccia of the dome and in an underlying andesite that yielded a zircon U-Pb age of 11.5 Ma.Short wave infrared spectrometer analyses were carried out for alteration mapping at Kluwih. There are two main stages of alteration produced by the hydrothermal activity. The alteration mineral assemblages indicate an advanced argillic alteration. The Cu mineralisation occurred in the form of enargite and subordinate chalcopyrite with an intergrown texture in the early stage. These mineralised veins are characterised by narrow pyrophyllite ± diaspore and dickite selvages (metres wide) and a peripheral K-muscovite envelope (sericitic alteration) up to 100 m wide. The K-muscovite envelope is zoned outward to Na-muscovite or Na-illite. Late-stage kaolinite and smectite alteration overprints the porphyritic dacite and may obscure the nature of early mica-clay alteration. The spatial distribution of different alteration assemblages suggests that the temperature of hydrothermal fluid increases with depth.Both the high-sulfidation mineralisation and advanced argillic alteration are suggested to be related to magmatic-hydrothermal fluids, which are likely to originate from an undiscovered deeper porphyry Cu-Au system below the porphyritic dacite. Based on alteration mapping results and comparisons to similar deposits, the porphyry intrusion could be up to 500 m below the volcanic dome. Further geochemical and mineralogical studies may help to target the potential underlying porphyry system.CITATION:Chan, J S-L, 2015. High-sulfidation epithermal Cu-Ag-Au deposit, Kluwih, eastern Java, Indonesia – alteration and implications for potential porphyry cu mineralisation, in Proceedings PACRIM 2015 Congress, pp 213–218 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The history of mining is rightly proud of its achievements in improving productivity and cost improvements over the years. No matter what measure is used, tonnes per manhour, cost per tonne, etc vast improvements have been made over the last hundred years. In fact over the last ten years in Australian coal mines raw coal output per employee has increased by 60 per cent. When one examines why these improvements have taken place the principal reasons have been technological advancement in mining equipment, excavator and dump truck capacity increases, longwall and continuous miners continually improving in reliability and size. Of course all these improvements are correlated to an increase in capital cost. Even with the above-mentioned advances the pressure for increased performance is as strong as ever. The international mining and mineral-processing sector is currently operating in a recessive market with some traditional commodities, eg gold trading at 20 year lows. During recessive times senior management will demand greater returns on capital employed: the obvious choices being reducing costs or increasing throughput. In addition, head office environments will often place a capital freeze on operational management so the opportunity to take advantage of technological change is not available. The challenge is, therefore, to increase throughput and cut costs without the need for capital. The answer is to optimise the existing labour and plant. If done systematically a result in productivity improvement, in our experience, as high as 45 per cent can be achieved with the average across South East Asia and Australasia being 21 - 23 per cent. The intention of this paper is to present a systematic approach to labour and machine utilisation thereby gaining the greatest possible return on the existing capital base.

Jan 1, 1999

By H Han, W Wang, E Zhou, D Duan

"In this study, physical, chemical and microscopic characteristics of high phosphorus oolitic hematite were studied firstly. Based on which, the new methods of high phosphorus hematite used in the æsolid state reduction by rotary hearth furnace - magnetic separationÆ and iron nugget by rotary hearth furnace direct reduction processes were discussed. The results showed that high temperature, low basicity and high carbon content is conducive for the apatite in iron ore to reduce into molten iron, but not conducive to the removal of phosphorus. Through optimisation of process parameters, dephosphorisation rate of high phosphorus hematite is more than 60 per cent by æsolid state reduction roasting-magnetic separationÆ process while that is up to 80 per cent by iron nugget process. This study can provide theoretical and technical basis on economical and rational use of high phosphorus oolitic hematite.CITATION:Han, H, Duan, D, Zhou, E and Wang, W, 2013. New methods for high phosphorus oolitic hematite dephosphorisation by direct reduction process, in Proceedings Iron Ore 2013, pp 391-396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By M E. Dunphy, P Silversmith

The Reefton Goldfield, both historically and potentially, represents a significant gold producing camp in the Westland province of New Zealand. Some two million ounces of gold have been produced from the Greenland Group host rocks between 1870 and 1951 with the most significant producers being the Blackwater and Globe Progress mines.   Steep terrain, high rainfall, poor outcrop, widespread fluvio-glacial deposits, tertiary cover and sometimes onerous environmental access conditions have proved a challenge to conventional exploration techniques. In addition classic exploration techniques have come up against a desire to reduce exploration cycle time and exploration costs while increasing both quality and quantity of geological information.   The trial, and subsequent implementation, of Wacker sampling has proved a highly successful and effective geochemical tool currently being utilised to target, discover, and define potential economic gold mineralisation in the Reefton Goldfield.

Jan 1, 1997

By M J. Kongas, K M. Saloheimo

This paper presents the art of on-stream particle size and elemental analysis used at iron ore concentrators, followed by the results and experiences from several sites.Online particle size analysis is rather common at medium- to large-sized concentrators. Online X-ray fluorescence (XRF) elemental analysis, however, is only used in some iron ore concentrators, while it is a routine practice in base metal concentrator plants. Online XRF analysis is applicable for process monitoring and control down to four to five per cent silica by measuring Fe assays accurately. With lower silica content, direct measurement of silica and other light elements is required. Some light element analysers that are based on the prompt gamma neutron activation analysis (PGNAA) method have been developed, but they have not performed up to expectations with slurry analysis. Other methods have been tried though these have not been used beyond prototype installations. Operating online light element slurry analyser installations are not common in iron ore applications.There is an economic incentive to mine lower and variable grade iron ore resources, which require concentration and removal of several impurities to produce high-quality concentrates for pellet production. Monitoring such operations by on-stream analysis has significant economic benefits, and there is a need to develop a dependable slurry online analyser for Si, Al, Mg and other light elements. The latest developments in slurry on-stream light element analysis are described.CITATION:Kongas, M J and Saloheimo, K M, 2013. Online slurry analysis for process control and monitoring at iron ore concentrators, in Proceedings Iron Ore 2013 , pp 303-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By A Giblett, M Daniel

"The Global Mining Standards and Guidelines Group (GMSG) currently supports nine individual industry working groups focused on developing standards and guidelines for the mining industry. In 2013 the GMSG established the Industrial Comminution Efficiency (ICE) working group to develop freely available guidelines for plant operators to quantify the operating efficiency of industrial comminution circuits. This initiative has engaged a diverse group of representatives from mining companies, equipment vendors, consultants and metallurgical laboratories with vast experience and capabilities in the field of comminution. The GMSG has issued the first two guidelines from the ICE working group in 2015–2016, with the third guideline having completed the approvals process and being in the final stages of editing ahead of release later in 2016.Two of the ICE guidelines present methods to quantify comminution circuit efficiency, and a complementary guideline describes best practice methods to collect the necessary samples and data to furnish these assessments. Collectively the guidelines cover sampling, survey data collection, laboratory testing procedures and calculation processes to allow the user to generate a relative circuit efficiency factor for the comminution circuit at the time of survey. The reference energy consumption is calculated considering the measured F80, P80 and ore strength at the time of survey, using either or both of the Bond or Morrell methods presented in GMSG guidelines dedicated to each method. The guidelines consequently provide the end user with practical tools to perform circuit efficiency analysis and to readily quantify the impact of optimisation efforts.This paper presents the content of the three ICE guidelines and describes their intended application.Citation:Giblett, A and Daniel, M, 2016. Global Mining Standards and Guidelines for Determining Comminution Circuit Efficiency, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

A method for the detection and analysis of tin in cassiterite ores is discussed. An empirical relationship was established between the tin content of an ore sample and the percentage absorption that this sample produced in a Mossbauer experiment. The time taken to complete an assay with this method is much less than with any of the methods currently in use. The equipment can be adapted readily for use in the field.

Jan 1, 1969

By M Furche, U Noell, C Grissemann, J A. Meima, T Graupner, A Romero-Baena

The mining residues at the abandoned copper mine site Pe±a de Hierro, located at the headwaters of the Rio Tinto, contribute substantially to the pollution of the river with high loads of Fe, As, Pb, Zn and Cu. The pH of the outflow ranges from 0.5 to 2.4 in the dry and wet season, respectively. One heap composed of alternating layers, which were deposited parallel to the slope, was investigated in detail. Unsorted blocky to fine materials including gossan material, pyritic volcanics, ashes from pyrite combustion and slate were observed here. The top of the heap has a gentle slope and a hill contouring channel-rip morphology. The initially rugged surface was smoothed by heavy rainfalls filling up the pores of the blocky material with fines. These fines are capable of storing the water for a prolonged time, providing an extended reaction time close to surface in a dry climate at extremely low pH conditions (one to four). All minerals, pyrite, mica, barite and even quartz (probably due to F released from dissolved mica) have been digested and silica gel precipitates have formed a stable and quasi impermeable 100 ¦m layer with very low porosity (<5 area per cent, estimated using scanning electron microscopy (SEM) imaging). The silica layer itself is covered by Fe-oxy-hydroxide (ie FeOOH) coating (10 ¦m) and seals a 1 - 5 mm thick stable hardpan. This hardpan covers the channels and part of the rips almost entirely, guiding the rainwater subhorizontally towards slopes and sinkholes. By geoelectrical measurements, a 3D-resistivity model of the internal structures and the bedrock relief underlying the heap was generated. Internal structures relate to lithological changes in a number of layers. Zones of low resistivity may be attributed to washed-in fines within the mega pore system, whilst zones of high resistivity close to the surface probably reflect the advanced stage of drying beneath aging hardpans. The water movement at the surface was investigated by an artificial precipitation experiment with monitoring of the subsequent changes in resistivities.

Jan 1, 2008

Development of the Boleo Process Flow Sheet and the Direct Solvent Extraction (DSX) Circuit for Cobalt and Zinc Recovery The metallurgical process designed to treat the El Boleo Cu-Co-Zn-Mn ore involves a sulphuric acid leach in seawater under oxidative and then reductive conditions to maximise metal extraction. Copper and cobalt are recovered as cathodes by electrowinning, zinc and manganese as zinc sulphate monohydrate and high quality manganese carbonate, respectively, by precipitation after a number of separation and purification stages. One of the key purification stages of the Boleo metallurgical process is the CSIRO DSX circuit. The DSX circuit was developed using the synergistic solvent extraction (SSX) technology. Initially, a synthetic solution was studied, and by adding 0.4 M LIX63 to 0.5 M Versatic 10 in Shellsol D70, large synergistic shifts were obtained for cobalt (?pH50 4.24) and zinc (?pH50 1.62). After a single contact, the separation factor of metals over manganese reached over 6,000 for cobalt and over 380 for zinc, indicating excellent separation of cobalt and good separation of zinc from manganese, magnesium and calcium. The SSX system was further optimised with the modified synthetic pilot plant solution. The extraction of cobalt and Zn after a single contact was 93 per cent and 70 per cent, respectively, while the Mn concentration in the loaded organic solution was only 0.28 g/L. A proof of principle pilot plant operation was conducted in 2004 and a demonstration pilot plant for final engineering design in 2006 with outstanding performance of the DSX circuit. For the demonstration pilot plant, the overall recovery of cobalt and zinc exceeded 99 per cent with a raffinate containing only 4 mg/L Zn and 1 mg/L Co. The DSX organic system showed no sign of degradation during the pilot plant operation, indicating good chemical stability under the anticipated commercial operating conditions. The DSX circuit will be implemented in the future Boleo processing plant.

Sep 13, 2010

By W Shamu

The mechanical properties of rock samples of identical lithologicalcomposition may vary significantly due to existence of materialdiscontinuities. Laboratory tests were carried out to determine the effect of material discontinuities on rock sample mechanical properties. The investigations consisted of detecting discontinuities, observing the failure mechanisms during uniaxial compressive strength tests, and analysing of the factors affecting the strength. A non-destructive testing method has been adopted to assist in thedetection of discontinuities. Laboratory testing proved that fractures leading to failures initiated on the detected discontinuities. The location, orientation, size, density and extent of the discontinuities contribute to different modes of failure and these affect the mechanical parameters of rock samples. Four modes of failure were distinguished for hard and brittlecylindrical rock samples. These modes were referred to as simple shear failure, multiple shear failure, multiple fracturing and vertical splitting. To evaluate the effect of discontinuities on mechanical parameters, the ratio of uniaxial compressive to tensile (Brazilian) strength was calculated and analysed for the different modes of failure. It was found that the value of the ratio depended on the mode of sample failure. The lowest value of the ratio was observed for shear mode of failure and the highest for vertical splitting mode of failure.

Jan 1, 1999

By D Craw

The Rise and Shine Shear Zone is a mineralised low angle deformation zone traceable for at least 7 km through biotite zone schist of the Dunstan Range, central Otago. Rocks from the shear zone obtained from recent drillholes are unweathered and facilitate paragenetic studies. There is a progression of mineral deposition from semiductile foliation-parallel shearing, to subsequent folding, and brittle fracturing. Sheared rocks are dominated by microshears containing fine grained hydrothermal muscovite and rutile that has recrystallised from metamorphic muscovite and titanite respectively. Euhedral pyrite occurs within segregations in the schist and is locally brecciated by the shears.   Arsenopyrite occurs within microshears and is intergrown with hyrothermal muscovite. Fractures within relatively undeformed schist are filled with ankerite, siderite, chalcopyrite, sphalerite and galena and these veinlets also crosscut the microshears. Locally the schist is folded and zones of brecciation, silicification and vein deposition overprint the rock. Vein quartz and albite predominate and arsenopyrite and gold infill breccia matrix and crosscutting veinlets. Sulphide deposition began in the later stages of metamorphism with pyrite deposited in quartz-albite segregations. Subsequent shearing caused brecciation of some grains and accompanied deposition of arsenopyrite ¦ gold and rare sulphides along foliation-parallel microshears. Minor amounts of chalcopyrite, sphalerite and galena were then remobilised in ankerite veins that crosscut the shears. In areas of high strain, arsenopyrite was then deposited as euhedral grains in veins and breccias. Synmineralisation deformation caused the brecciation of some grains and gold was deposited infilling fractures in the arsenopyrite. The paragenetic sequence shows gold mineralisation occurred in two distinct sets of structures (semiductile and brittle) that formed at different times in the formation of the shear zone.

Jan 1, 2006

Separation of Nickel and Cobalt from Manganese, Magnesium and Calcium by Synergistic Solvent Extraction - From Batch Tests to Pilot Plant Operation The synergistic solvent extraction system consisting of Versatic 10/LIX63/TBP was used for the separation and purification of nickel and cobalt from synthetic laterite leach solution after iron removal. Very encouraging results were obtained for separating nickel and cobalt from manganese, magnesium and calcium. In batch tests, the organic composition of the synergistic system was optimised and very large synergistic shifts for nickel and cobalt were observed. The ?pH50(Mn-Co) and ?pH50(Mn-Ni) values were as large as 1.65 and 2.40, respectively. The extraction and stripping kinetics of nickel and cobalt was fast. Semi continuous extraction tests were conducted with a pH profile of 5.5/6.1/6.5 in three stages at 40¦C. The nickel and cobalt extractions reached 99.9 per cent with only 5 mg/L Ni and <1 mg/L Co left in the raffinate. With two stages of scrubbing, only 2 mg/L Mn and less than 1 mg/L Mg and Ca were left in the scrubbed organic solution. With two stripping stages, the stripping efficiencies of Ni and Co reached over 95 per cent. A fully continuous pilot plant operation was conducted successfully for 280 hours. With an O/A ratio of about 2 and a pH profile of 5.5/5.8/6.0/6.3 for the four stages EX1/EX2/Ex3/EX4, both nickel and cobalt were almost completely extracted. Using a pH profile of 5.4/5.0 for SC1/SC2, the manganese scrubbing efficiency was over 96 per cent. Using three strip stages, over 98 per cent Ni and 99 per cent Co were stripped with only 64 mg/L Ni in the stripped organic solution. The nickel concentration in the loaded strip liquor reached 83 g/L, resulting in a ?Ni of over 28 g/L. The chemical stability of the system was also assessed over 12 weeks under proposed industrial operating conditions. Operation exclusively under strip conditions at 50¦C and 40¦C resulted in LIX63 oxime half lives of 1.1 and 2.1 years, respectively. Operation exclusively under extract conditions at 50¦C and 40¦C resulted in oxime half lives of 0.26 and 0.82 years, respectively. Losses of Versatic 10 were less than four per cent.

Sep 13, 2010

By G J. Lyman, F S. Bourgeois

As the prices of metals slide, financial control of mineral processing operations becomes more and more important. Control of a mineral processing operation implies measurement of grades, recoveries and losses, with every effort being made to recover more product from the same feed. Shareholders become more concerned with the transparency of the operations and the corporate governance.There is only one way to achieve this and this is by sampling and making good use of the results of that sampling. Sampling systems that provide only 'rough' figures are not good enough. Similarly, a competitive position in the marketplace demands close control of product quality. Maximisation of product output demands that the product just meet the specification so that product yield is maximised. Decisions based on precise sampling results carry less risk that those based on imprecise results.This paper reports some recent advances in sampling theory that permit full quantification of sampling distributions, not just the sampling variance as has been possible in the past. These advances can be used together with simulation methods to tie down sampling precisions and develop calculations that quantify decision making risk when using the sampling results. A number of examples illustrate the use of the new advances and a final example indicates the development of risk analysis curves in the coupling of sampling precision to sale of a commodity.CITATION:Lyman, G J and Bourgeois, F S, 2015. Sampling, corporate governance and risk analysis, in Proceedings MetPlant 2015, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By K Firmin

The Mt Tom Price orebody of Hamersley Iron Pty Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the ore body, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control of products based on selective mining is the production of advance data on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades are determined from assay of samples taken from blast hole cuttings. As shales are more friable than hematite, product fines are always lower in iron grade than the lump product. The realisation of contract specification grade is more difficult with fines than with lump, so maintaining the correct fines grade becomes a prime factor in quality control. Control of fines grade is presently effected by aiming for an appropriate feed grade to the primary stockpile. Studies to estimate fines grade directly by qualitatively taking into account material types are in progress. Quality control measures are checked by monitoring the crushing and screening plant output, and taking appropriate compensatory actions in the mine when required. Minor fluctuations in quality of fines can be blended out on stockpiles. The quality control measures described ensure constant quality products, and a good recovery of high grade material from the deposit.

Jan 1, 1971

The Crown Minerals Act provides a new+framework for the management of Crown owned minerals and requires that regard be had for the principles of the Treaty of Waitangi. The Act requires the preparation of Minerals Programmes to achieve the Act's objectives of efficient allocation of rights and the recovery of a fair financial return on its minerals. Efficient allocation requires that a permit is allocated to the party which values it most highly. A fair financial return to the Crown must be considered in the context of the economic rent available from individual mineral projects, with the proviso that a nil return to the Crown as the owner of the resource will not be considered a fair return from the community's perspective.

Jan 1, 1992

In the plumbing of vertical shafts the methods employed and equipment used, are generally made to best suit existing conditions. Undoubtedly, there is no method that can be called standard or that can be used with equal ease and success on all shafts. At the Mount Isa Mines Limited property in Northern Queensland, Australia, local conditions have presented no major difficulties to be overcome in shaft plumbing work. In fact, compared to those at many shafts, the problem has been rather simple. There are three vertical shafts connecting main mine workings, with the greatest plumbing depth for any single lift, 350 ft.Other conditions pertaining to plumbing work have been generally normal.The method we have employed is, in principle, similar to the Weisbach orientation method with a variation that does not necessitate damping of the wires to bring them to rest. Although conditions encountered have not been such that damping the wires would have been inconvenient, we feel we have saved much time and eliminated unnecessary...

Jan 1, 1940

The recent boom in the mining industry has lead to some unique challenges in successfully operating processing plants. With high turn-over rates of both operators and technical staff, and many experienced personnel leaving regional sites for city based jobs there is often an onsite knowledge vacuum and this in turn puts pressure on both site training departments and senior metallurgists to provide the relevant skills to the continuous stream of new staff. Frequently both operators and new metallurgists are instructed on a æhow-toÆ basis rather than giving them the understanding as to why tasks are performed and decisions are made. This paper has been written with the plant operator and metallurgist in mind and aims to provide suitable material to be incorporated into a site training manual. Topics have been broadly divided into the following categories: factors that operational staff can control; including pulp density, air addition rate, froth depth, particle size and reagent type and use; factors that operational staff cannot control; providing general information on bubble size, froth stability, pulp chemistry and the mechanical effects of the rotor/stator system; and process improvements. Each topic is discussed with a view to clarifying the key process variables that need to be understood and optimised in an industrial operating plant.

Jan 1, 2009

By E V. Kislov

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Northern Baikal Ni-Cu province is located in Buryatia, south-east Siberia, and geologically is part of the Baikal-Muya volcano-plutonic belt. It is known for numerous PGE-Ni-Cu-bearing mafic-ultramafic intrusions of Neoproterozoic age formed in various geodynamic settings. All these deposits can be regarded as a single Ni-Cu ore cluster located near the Kholodninskoe Pb-Zn deposit, which is ready for mining. In addition, there are less studied, small dyke-like bodies with sulfide mineralisation that formed in a rift setting and may be enriched in Ni, Cu and PGE. Individually, the known bodies are of poor commercial value by their resources, but their close spatial association (<30 km) may make these PGE-Ni-Cu deposits economic in the future. This extended abstract seeks to provide a geological framework of the North Baikal Ni-Cu-PGE province, specifically at the north-eastern Synnyr rift hosting numerous small subvolcanic bodies with Ni-Cu sulfide mineralisation. Some small subvolcanic bodies contain industrial level Ni-Cu deposits (Shanuch, Cabanga-Musongati, Voisey’s Bay, Jinchuan, etc).CITATION:Kislov, E V, 2015. North Baikal region Ni-Cu deposits , in Proceedings PACRIM 2015 Congress, pp 297–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J Coward, S Bulatovic

There are currently two operators producing oil from the surface-mineable portions of AlbertaÆs oil sands (Syncrude Canada Ltd and Suncor Inc) and two other companies are proposing to enter the industry (Albian Sands Energy Inc in 2002 and True North Energy LP in 2004). Tailings from the two current oil sands plants contain approximately 220 000 tonnes per year of TiO2 and approximately 80 000 tonnes per year of zircon. This represents approximately six per cent of the worldÆs TiO2 consumption and approximately nine per cent of the worldÆs zircon production. With the commissioning of plants by Albian and True North, and the announced expansion of plants by Syncrude and Suncor, it is expected that these tonnages could quadruple in the next ten years. All of these operators have at least 50 years of reserves even at these expanded production rates. The occurrence of heavy minerals in AlbertaÆs oil sands has long been known and is well documented in the literature. There have been a number of attempts to produce market-grade products from this resource and the results of this work have been quite mixed. Typically, researchers have used the normal mineral dressing techniques of the industry and have found the mineral assemblage does not respond to these techniques all that well. This has led to the widely-held suspicion that there must be some difficult metallurgical problems associated with this resource. There are three main problem areas that have created difficulties for previous researchers:the bitumen coating on the sand grains; secondary mineralisation such as pyrite, siderite and calcite; and a high proportion of aluminosilicates (approximately 25 per cent) that have the same gravity, electrostatic and magnetic properties as other minerals in the heavy mineral suite. Recent work by Lakefield Research shows that these problems can be largely overcome with some novel approaches. The bitumen can be removed by washing with a solvent in the presence of a demulsifier; the pyrite can be removed by flotation; and the titanium and zircon minerals can be separated by selective flotation followed by conventional electrostatic and magnetic separation.

Jan 1, 2001

Applicaton of Agricultural Residues from Pyrolysis in Flotation of Black Coal

Sep 13, 2010